From: Peter Yin <peteryin.openbmc@gmail.com> To: patrick@stwcx.xyz, Wim Van Sebroeck <wim@linux-watchdog.org>, Guenter Roeck <linux@roeck-us.net>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Conor Dooley <conor+dt@kernel.org>, Joel Stanley <joel@jms.id.au>, Andrew Jeffery <andrew@codeconstruct.com.au>, linux-watchdog@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-aspeed@lists.ozlabs.org, linux-kernel@vger.kernel.org Subject: [PATCH v4 4/4] drivers: watchdog: ast2500 and ast2600 support bootstatus Date: Wed, 27 Mar 2024 16:53:30 +0800 [thread overview] Message-ID: <20240327085330.3281697-5-peteryin.openbmc@gmail.com> (raw) In-Reply-To: <20240327085330.3281697-1-peteryin.openbmc@gmail.com> Add WDIOF_EXTERN1 and WDIOF_CARDRESET bootstatus in ast2600 Regarding the AST2600 specification, the WDTn Timeout Status Register (WDT10) has bit 1 reserved. Bit 1 of the status register indicates on ast2500 if the boot was from the second boot source. It does not indicate that the most recent reset was triggered by the watchdog. The code should just be changed to set WDIOF_CARDRESET if bit 0 of the status register is set. Include SCU register to veriy WDIOF_EXTERN1 in ast2600 SCU74 or ast2500 SCU3C when bit1 is set. Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> --- drivers/watchdog/aspeed_wdt.c | 60 +++++++++++++++++++++++++---------- 1 file changed, 44 insertions(+), 16 deletions(-) diff --git a/drivers/watchdog/aspeed_wdt.c b/drivers/watchdog/aspeed_wdt.c index b4773a6aaf8c..29e9afdee619 100644 --- a/drivers/watchdog/aspeed_wdt.c +++ b/drivers/watchdog/aspeed_wdt.c @@ -11,10 +11,12 @@ #include <linux/io.h> #include <linux/kernel.h> #include <linux/kstrtox.h> +#include <linux/mfd/syscon.h> #include <linux/module.h> #include <linux/of.h> #include <linux/of_irq.h> #include <linux/platform_device.h> +#include <linux/regmap.h> #include <linux/watchdog.h> static bool nowayout = WATCHDOG_NOWAYOUT; @@ -65,23 +67,32 @@ MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table); #define WDT_RELOAD_VALUE 0x04 #define WDT_RESTART 0x08 #define WDT_CTRL 0x0C -#define WDT_CTRL_BOOT_SECONDARY BIT(7) -#define WDT_CTRL_RESET_MODE_SOC (0x00 << 5) -#define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5) -#define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5) -#define WDT_CTRL_1MHZ_CLK BIT(4) -#define WDT_CTRL_WDT_EXT BIT(3) -#define WDT_CTRL_WDT_INTR BIT(2) -#define WDT_CTRL_RESET_SYSTEM BIT(1) -#define WDT_CTRL_ENABLE BIT(0) +#define WDT_CTRL_BOOT_SECONDARY BIT(7) +#define WDT_CTRL_RESET_MODE_SOC (0x00 << 5) +#define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5) +#define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5) +#define WDT_CTRL_1MHZ_CLK BIT(4) +#define WDT_CTRL_WDT_EXT BIT(3) +#define WDT_CTRL_WDT_INTR BIT(2) +#define WDT_CTRL_RESET_SYSTEM BIT(1) +#define WDT_CTRL_ENABLE BIT(0) #define WDT_TIMEOUT_STATUS 0x10 -#define WDT_TIMEOUT_STATUS_IRQ BIT(2) -#define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1) +#define WDT_TIMEOUT_STATUS_IRQ BIT(2) +#define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1) +#define WDT_TIMEOUT_STATUS_EVENT BIT(0) #define WDT_CLEAR_TIMEOUT_STATUS 0x14 -#define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0) +#define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0) #define WDT_RESET_MASK1 0x1c #define WDT_RESET_MASK2 0x20 +/* + * Ast2600 SCU74 bit1 is External reset flag + * Ast2500 SCU3C bit1 is External reset flag + */ +#define EXTERN_RESET_FLAG BIT(1) +#define AST2500_SYSTEM_RESET_EVENT 0x3C +#define AST2600_SYSTEM_RESET_EVENT 0x74 + /* * WDT_RESET_WIDTH controls the characteristics of the external pulse (if * enabled), specifically: @@ -330,6 +341,11 @@ static int aspeed_wdt_probe(struct platform_device *pdev) if (IS_ERR(wdt->base)) return PTR_ERR(wdt->base); + struct regmap *scu_base = syscon_regmap_lookup_by_phandle(dev->of_node, + "aspeed,scu"); + if (IS_ERR(scu_base)) + return PTR_ERR(scu_base); + wdt->wdd.info = &aspeed_wdt_info; if (wdt->cfg->irq_mask) { @@ -459,14 +475,26 @@ static int aspeed_wdt_probe(struct platform_device *pdev) } status = readl(wdt->base + WDT_TIMEOUT_STATUS); - if (status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY) { + if (status & WDT_TIMEOUT_STATUS_EVENT) wdt->wdd.bootstatus = WDIOF_CARDRESET; - if (of_device_is_compatible(np, "aspeed,ast2400-wdt") || - of_device_is_compatible(np, "aspeed,ast2500-wdt")) - wdt->wdd.groups = bswitch_groups; + if (of_device_is_compatible(np, "aspeed,ast2600-wdt")) { + ret = regmap_read(scu_base, + AST2600_SYSTEM_RESET_EVENT, + &status); + } else { + ret = regmap_read(scu_base, + AST2500_SYSTEM_RESET_EVENT, + &status); + wdt->wdd.groups = bswitch_groups; } + /* + * Reset cause by Extern Reset + */ + if (status & EXTERN_RESET_FLAG && !ret) + wdt->wdd.bootstatus |= WDIOF_EXTERN1; + dev_set_drvdata(dev, wdt); return devm_watchdog_register_device(dev, &wdt->wdd); -- 2.25.1
WARNING: multiple messages have this Message-ID (diff)
From: Peter Yin <peteryin.openbmc@gmail.com> To: patrick@stwcx.xyz, Wim Van Sebroeck <wim@linux-watchdog.org>, Guenter Roeck <linux@roeck-us.net>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Conor Dooley <conor+dt@kernel.org>, Joel Stanley <joel@jms.id.au>, Andrew Jeffery <andrew@codeconstruct.com.au>, linux-watchdog@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-aspeed@lists.ozlabs.org, linux-kernel@vger.kernel.org Subject: [PATCH v4 4/4] drivers: watchdog: ast2500 and ast2600 support bootstatus Date: Wed, 27 Mar 2024 16:53:30 +0800 [thread overview] Message-ID: <20240327085330.3281697-5-peteryin.openbmc@gmail.com> (raw) In-Reply-To: <20240327085330.3281697-1-peteryin.openbmc@gmail.com> Add WDIOF_EXTERN1 and WDIOF_CARDRESET bootstatus in ast2600 Regarding the AST2600 specification, the WDTn Timeout Status Register (WDT10) has bit 1 reserved. Bit 1 of the status register indicates on ast2500 if the boot was from the second boot source. It does not indicate that the most recent reset was triggered by the watchdog. The code should just be changed to set WDIOF_CARDRESET if bit 0 of the status register is set. Include SCU register to veriy WDIOF_EXTERN1 in ast2600 SCU74 or ast2500 SCU3C when bit1 is set. Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> --- drivers/watchdog/aspeed_wdt.c | 60 +++++++++++++++++++++++++---------- 1 file changed, 44 insertions(+), 16 deletions(-) diff --git a/drivers/watchdog/aspeed_wdt.c b/drivers/watchdog/aspeed_wdt.c index b4773a6aaf8c..29e9afdee619 100644 --- a/drivers/watchdog/aspeed_wdt.c +++ b/drivers/watchdog/aspeed_wdt.c @@ -11,10 +11,12 @@ #include <linux/io.h> #include <linux/kernel.h> #include <linux/kstrtox.h> +#include <linux/mfd/syscon.h> #include <linux/module.h> #include <linux/of.h> #include <linux/of_irq.h> #include <linux/platform_device.h> +#include <linux/regmap.h> #include <linux/watchdog.h> static bool nowayout = WATCHDOG_NOWAYOUT; @@ -65,23 +67,32 @@ MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table); #define WDT_RELOAD_VALUE 0x04 #define WDT_RESTART 0x08 #define WDT_CTRL 0x0C -#define WDT_CTRL_BOOT_SECONDARY BIT(7) -#define WDT_CTRL_RESET_MODE_SOC (0x00 << 5) -#define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5) -#define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5) -#define WDT_CTRL_1MHZ_CLK BIT(4) -#define WDT_CTRL_WDT_EXT BIT(3) -#define WDT_CTRL_WDT_INTR BIT(2) -#define WDT_CTRL_RESET_SYSTEM BIT(1) -#define WDT_CTRL_ENABLE BIT(0) +#define WDT_CTRL_BOOT_SECONDARY BIT(7) +#define WDT_CTRL_RESET_MODE_SOC (0x00 << 5) +#define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5) +#define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5) +#define WDT_CTRL_1MHZ_CLK BIT(4) +#define WDT_CTRL_WDT_EXT BIT(3) +#define WDT_CTRL_WDT_INTR BIT(2) +#define WDT_CTRL_RESET_SYSTEM BIT(1) +#define WDT_CTRL_ENABLE BIT(0) #define WDT_TIMEOUT_STATUS 0x10 -#define WDT_TIMEOUT_STATUS_IRQ BIT(2) -#define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1) +#define WDT_TIMEOUT_STATUS_IRQ BIT(2) +#define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1) +#define WDT_TIMEOUT_STATUS_EVENT BIT(0) #define WDT_CLEAR_TIMEOUT_STATUS 0x14 -#define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0) +#define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0) #define WDT_RESET_MASK1 0x1c #define WDT_RESET_MASK2 0x20 +/* + * Ast2600 SCU74 bit1 is External reset flag + * Ast2500 SCU3C bit1 is External reset flag + */ +#define EXTERN_RESET_FLAG BIT(1) +#define AST2500_SYSTEM_RESET_EVENT 0x3C +#define AST2600_SYSTEM_RESET_EVENT 0x74 + /* * WDT_RESET_WIDTH controls the characteristics of the external pulse (if * enabled), specifically: @@ -330,6 +341,11 @@ static int aspeed_wdt_probe(struct platform_device *pdev) if (IS_ERR(wdt->base)) return PTR_ERR(wdt->base); + struct regmap *scu_base = syscon_regmap_lookup_by_phandle(dev->of_node, + "aspeed,scu"); + if (IS_ERR(scu_base)) + return PTR_ERR(scu_base); + wdt->wdd.info = &aspeed_wdt_info; if (wdt->cfg->irq_mask) { @@ -459,14 +475,26 @@ static int aspeed_wdt_probe(struct platform_device *pdev) } status = readl(wdt->base + WDT_TIMEOUT_STATUS); - if (status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY) { + if (status & WDT_TIMEOUT_STATUS_EVENT) wdt->wdd.bootstatus = WDIOF_CARDRESET; - if (of_device_is_compatible(np, "aspeed,ast2400-wdt") || - of_device_is_compatible(np, "aspeed,ast2500-wdt")) - wdt->wdd.groups = bswitch_groups; + if (of_device_is_compatible(np, "aspeed,ast2600-wdt")) { + ret = regmap_read(scu_base, + AST2600_SYSTEM_RESET_EVENT, + &status); + } else { + ret = regmap_read(scu_base, + AST2500_SYSTEM_RESET_EVENT, + &status); + wdt->wdd.groups = bswitch_groups; } + /* + * Reset cause by Extern Reset + */ + if (status & EXTERN_RESET_FLAG && !ret) + wdt->wdd.bootstatus |= WDIOF_EXTERN1; + dev_set_drvdata(dev, wdt); return devm_watchdog_register_device(dev, &wdt->wdd); -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2024-03-27 8:53 UTC|newest] Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top 2024-03-27 8:53 [PATCH v4 0/4] drivers: watchdog: ast2500 and ast2600 support bootstatus Peter Yin 2024-03-27 8:53 ` Peter Yin 2024-03-27 8:53 ` [PATCH v4 1/4] ARM: dts: aspeed: Add the AST2500 WDT with SCU register Peter Yin 2024-03-27 8:53 ` Peter Yin 2024-03-27 8:53 ` [PATCH v4 2/4] ARM: dts: aspeed: Add the AST2600 " Peter Yin 2024-03-27 8:53 ` Peter Yin 2024-03-27 8:53 ` [PATCH v4 3/4] dt-bindings: watchdog: aspeed-wdt: Add aspeed,scu Peter Yin 2024-03-27 8:53 ` Peter Yin 2024-03-27 8:53 ` Peter Yin [this message] 2024-03-27 8:53 ` [PATCH v4 4/4] drivers: watchdog: ast2500 and ast2600 support bootstatus Peter Yin 2024-03-27 15:47 ` Guenter Roeck 2024-03-27 15:47 ` Guenter Roeck 2024-03-27 16:07 ` Chia Hsing Yin 2024-03-27 16:07 ` Chia Hsing Yin
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20240327085330.3281697-5-peteryin.openbmc@gmail.com \ --to=peteryin.openbmc@gmail.com \ --cc=andrew@codeconstruct.com.au \ --cc=conor+dt@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=joel@jms.id.au \ --cc=krzysztof.kozlowski+dt@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-aspeed@lists.ozlabs.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-watchdog@vger.kernel.org \ --cc=linux@roeck-us.net \ --cc=patrick@stwcx.xyz \ --cc=robh+dt@kernel.org \ --cc=wim@linux-watchdog.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.