From: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
To: lpieralisi@kernel.org, kw@linux.com, robh@kernel.org,
bhelgaas@google.com, krzysztof.kozlowski+dt@linaro.org,
conor+dt@kernel.org, jingoohan1@gmail.com, mani@kernel.org
Cc: marek.vasut+renesas@gmail.com, linux-pci@vger.kernel.org,
devicetree@vger.kernel.org, linux-renesas-soc@vger.kernel.org,
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Subject: [PATCH v4 6/7] PCI: dwc: rcar-gen4: Add support for r8a779g0
Date: Wed, 3 Apr 2024 14:33:03 +0900 [thread overview]
Message-ID: <20240403053304.3695096-7-yoshihiro.shimoda.uh@renesas.com> (raw)
In-Reply-To: <20240403053304.3695096-1-yoshihiro.shimoda.uh@renesas.com>
This driver previously supported r8a779f0 (R-Car S4-8). Add support
for r8a779g0 (R-Car V4H).
To support r8a779g0, it requires specific firmware.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
drivers/pci/controller/dwc/pcie-rcar-gen4.c | 201 +++++++++++++++++++-
1 file changed, 200 insertions(+), 1 deletion(-)
diff --git a/drivers/pci/controller/dwc/pcie-rcar-gen4.c b/drivers/pci/controller/dwc/pcie-rcar-gen4.c
index e760bcd30c4e..5d5a088bd2c1 100644
--- a/drivers/pci/controller/dwc/pcie-rcar-gen4.c
+++ b/drivers/pci/controller/dwc/pcie-rcar-gen4.c
@@ -5,8 +5,10 @@
*/
#include <linux/delay.h>
+#include <linux/firmware.h>
#include <linux/interrupt.h>
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/pci.h>
@@ -20,9 +22,10 @@
/* Renesas-specific */
/* PCIe Mode Setting Register 0 */
#define PCIEMSR0 0x0000
-#define BIFUR_MOD_SET_ON BIT(0)
+#define APP_SRIS_MODE BIT(6)
#define DEVICE_TYPE_EP 0
#define DEVICE_TYPE_RC BIT(4)
+#define BIFUR_MOD_SET_ON BIT(0)
/* PCIe Interrupt Status 0 */
#define PCIEINTSTS0 0x0084
@@ -37,19 +40,47 @@
#define PCIEDMAINTSTSEN 0x0314
#define PCIEDMAINTSTSEN_INIT GENMASK(15, 0)
+/* Port Logic Registers 89 */
+#define PRTLGC89 0x0b70
+
+/* Port Logic Registers 90 */
+#define PRTLGC90 0x0b74
+
/* PCIe Reset Control Register 1 */
#define PCIERSTCTRL1 0x0014
#define APP_HOLD_PHY_RST BIT(16)
#define APP_LTSSM_ENABLE BIT(0)
+/* PCIe Power Management Control */
+#define PCIEPWRMNGCTRL 0x0070
+#define APP_CLK_REQ_N BIT(11)
+#define APP_CLK_PM_EN BIT(10)
+
+/*
+ * The R-Car Gen4 documents don't describe the PHY registers' name.
+ * But, the initialization procedure describes these offsets. So,
+ * this driver makes up own #defines for the offsets.
+ */
+#define RCAR_GEN4_PCIE_PHY_0f8 0x0f8
+#define RCAR_GEN4_PCIE_PHY_148 0x148
+#define RCAR_GEN4_PCIE_PHY_1d4 0x1d4
+#define RCAR_GEN4_PCIE_PHY_514 0x514
+#define RCAR_GEN4_PCIE_PHY_700 0x700
+
#define RCAR_NUM_SPEED_CHANGE_RETRIES 10
#define RCAR_MAX_LINK_SPEED 4
#define RCAR_GEN4_PCIE_EP_FUNC_DBI_OFFSET 0x1000
#define RCAR_GEN4_PCIE_EP_FUNC_DBI2_OFFSET 0x800
+#define RCAR_GEN4_PCIE_FIRMWARE_NAME "rcar_gen4_pcie.bin"
+#define RCAR_GEN4_PCIE_FIRMWARE_BASE_ADDR 0xc000
+
+MODULE_FIRMWARE(RCAR_GEN4_PCIE_FIRMWARE_NAME);
+
struct rcar_gen4_pcie;
struct rcar_gen4_pcie_platdata {
+ void (*additional_common_init)(struct rcar_gen4_pcie *rcar);
int (*ltssm_enable)(struct rcar_gen4_pcie *rcar);
enum dw_pcie_device_mode mode;
};
@@ -57,12 +88,144 @@ struct rcar_gen4_pcie_platdata {
struct rcar_gen4_pcie {
struct dw_pcie dw;
void __iomem *base;
+ void __iomem *phy_base;
struct platform_device *pdev;
const struct rcar_gen4_pcie_platdata *platdata;
};
#define to_rcar_gen4_pcie(_dw) container_of(_dw, struct rcar_gen4_pcie, dw)
/* Common */
+static void rcar_gen4_pcie_phy_reg_update_bits(struct rcar_gen4_pcie *rcar,
+ u32 offset, u32 mask, u32 val)
+{
+ u32 tmp;
+
+ tmp = readl(rcar->phy_base + offset);
+ tmp &= ~mask;
+ tmp |= val;
+ writel(tmp, rcar->phy_base + offset);
+}
+
+static int rcar_gen4_pcie_reg_check_bit(struct rcar_gen4_pcie *rcar,
+ u32 offset, u32 mask)
+{
+ struct dw_pcie *dw = &rcar->dw;
+
+ if (dw_pcie_readl_dbi(dw, offset) & mask)
+ return -EAGAIN;
+
+ return 0;
+}
+
+static int rcar_gen4_pcie_update_phy_firmware(struct rcar_gen4_pcie *rcar)
+{
+ const u32 check_addr[] = { 0x00101018, 0x00101118, 0x00101021, 0x00101121};
+ struct dw_pcie *dw = &rcar->dw;
+ const struct firmware *fw;
+ unsigned int i, timeout;
+ u32 data;
+ int ret;
+
+ ret = request_firmware(&fw, RCAR_GEN4_PCIE_FIRMWARE_NAME, dw->dev);
+ if (ret) {
+ dev_err(dw->dev, "%s: Requesting firmware failed\n", __func__);
+ return ret;
+ }
+
+ for (i = 0; i < (fw->size / 2); i++) {
+ data = fw->data[i * 2] | fw->data[(i * 2) + 1] << 8;
+ timeout = 100;
+ do {
+ dw_pcie_writel_dbi(dw, PRTLGC89, RCAR_GEN4_PCIE_FIRMWARE_BASE_ADDR + i);
+ dw_pcie_writel_dbi(dw, PRTLGC90, data);
+ if (rcar_gen4_pcie_reg_check_bit(rcar, PRTLGC89, BIT(30)) >= 0)
+ break;
+ if (!(--timeout)) {
+ ret = -ETIMEDOUT;
+ goto exit;
+ }
+ usleep_range(100, 200);
+ } while (1);
+ }
+
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_0f8, BIT(17), BIT(17));
+
+ for (i = 0; i < ARRAY_SIZE(check_addr); i++) {
+ timeout = 100;
+ do {
+ dw_pcie_writel_dbi(dw, PRTLGC89, check_addr[i]);
+ ret = rcar_gen4_pcie_reg_check_bit(rcar, PRTLGC89, BIT(30));
+ ret |= rcar_gen4_pcie_reg_check_bit(rcar, PRTLGC90, BIT(0));
+ if (ret >= 0)
+ break;
+ if (!(--timeout)) {
+ ret = -ETIMEDOUT;
+ goto exit;
+ }
+ usleep_range(100, 200);
+ } while (1);
+ }
+
+ ret = 0;
+exit:
+ release_firmware(fw);
+
+ return ret;
+}
+
+static int rcar_gen4_pcie_enable_phy(struct rcar_gen4_pcie *rcar)
+{
+ struct dw_pcie *dw = &rcar->dw;
+ u32 val;
+ int ret;
+
+ val = dw_pcie_readl_dbi(dw, PCIE_PORT_FORCE);
+ val |= PORT_FORCE_DO_DESKEW_FOR_SRIS;
+ dw_pcie_writel_dbi(dw, PCIE_PORT_FORCE, val);
+
+ val = readl(rcar->base + PCIEMSR0);
+ val |= APP_SRIS_MODE;
+ writel(val, rcar->base + PCIEMSR0);
+
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_700, BIT(28), 0);
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_700, BIT(20), 0);
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_700, BIT(12), 0);
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_700, BIT(4), 0);
+
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_148,
+ GENMASK(23, 22), BIT(22));
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_148,
+ GENMASK(18, 16), GENMASK(17, 16));
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_148,
+ GENMASK(7, 6), BIT(6));
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_148,
+ GENMASK(2, 0), GENMASK(11, 0));
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_1d4,
+ GENMASK(16, 15), GENMASK(16, 15));
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_514, BIT(26), BIT(26));
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_0f8, BIT(16), 0);
+ rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_0f8, BIT(19), BIT(19));
+
+ val = readl(rcar->base + PCIERSTCTRL1);
+ val &= ~APP_HOLD_PHY_RST;
+ writel(val, rcar->base + PCIERSTCTRL1);
+
+ ret = readl_poll_timeout(rcar->phy_base + RCAR_GEN4_PCIE_PHY_0f8, val,
+ !(val & BIT(18)), 100, 10000);
+ if (ret < 0)
+ return ret;
+
+ ret = rcar_gen4_pcie_update_phy_firmware(rcar);
+ if (ret)
+ return ret;
+
+ val = readl(rcar->base + PCIERSTCTRL1);
+ val |= APP_LTSSM_ENABLE;
+ writel(val, rcar->base + PCIERSTCTRL1);
+
+ return 0;
+}
+
static void rcar_gen4_pcie_ltssm_control(struct rcar_gen4_pcie *rcar,
bool enable)
{
@@ -200,6 +363,9 @@ static int rcar_gen4_pcie_common_init(struct rcar_gen4_pcie *rcar)
if (ret)
goto err_unprepare;
+ if (rcar->platdata->additional_common_init)
+ rcar->platdata->additional_common_init(rcar);
+
return 0;
err_unprepare:
@@ -241,6 +407,10 @@ static void rcar_gen4_pcie_unprepare(struct rcar_gen4_pcie *rcar)
static int rcar_gen4_pcie_get_resources(struct rcar_gen4_pcie *rcar)
{
+ rcar->phy_base = devm_platform_ioremap_resource_byname(rcar->pdev, "phy");
+ if (IS_ERR(rcar->phy_base))
+ return PTR_ERR(rcar->base);
+
/* Renesas-specific registers */
rcar->base = devm_platform_ioremap_resource_byname(rcar->pdev, "app");
@@ -517,6 +687,31 @@ static int r8a779f0_pcie_ltssm_enable(struct rcar_gen4_pcie *rcar)
return 0;
}
+static void rcar_gen4_pcie_additional_common_init(struct rcar_gen4_pcie *rcar)
+{
+ struct dw_pcie *dw = &rcar->dw;
+ u32 val;
+
+ /*
+ * The SoC manual said the register setting is required. Otherwise,
+ * linkup failed.
+ */
+ val = dw_pcie_readl_dbi(dw, PCIE_PORT_LANE_SKEW);
+ val &= ~PORT_LANE_SKEW_INSERT_MASK;
+ if (dw->num_lanes < 4)
+ val |= BIT(6);
+ dw_pcie_writel_dbi(dw, PCIE_PORT_LANE_SKEW, val);
+
+ val = readl(rcar->base + PCIEPWRMNGCTRL);
+ val |= APP_CLK_REQ_N | APP_CLK_PM_EN;
+ writel(val, rcar->base + PCIEPWRMNGCTRL);
+}
+
+static int rcar_gen4_pcie_ltssm_enable(struct rcar_gen4_pcie *rcar)
+{
+ return rcar_gen4_pcie_enable_phy(rcar);
+}
+
static struct rcar_gen4_pcie_platdata platdata_r8a779f0_pcie = {
.ltssm_enable = r8a779f0_pcie_ltssm_enable,
.mode = DW_PCIE_RC_TYPE,
@@ -528,10 +723,14 @@ static struct rcar_gen4_pcie_platdata platdata_r8a779f0_pcie_ep = {
};
static struct rcar_gen4_pcie_platdata platdata_rcar_gen4_pcie = {
+ .additional_common_init = rcar_gen4_pcie_additional_common_init,
+ .ltssm_enable = rcar_gen4_pcie_ltssm_enable,
.mode = DW_PCIE_RC_TYPE,
};
static struct rcar_gen4_pcie_platdata platdata_rcar_gen4_pcie_ep = {
+ .additional_common_init = rcar_gen4_pcie_additional_common_init,
+ .ltssm_enable = rcar_gen4_pcie_ltssm_enable,
.mode = DW_PCIE_EP_TYPE,
};
--
2.25.1
next prev parent reply other threads:[~2024-04-03 5:33 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-04-03 5:32 [PATCH v4 0/7] PCI: dwc: rcar-gen4: Add R-Car V4H support Yoshihiro Shimoda
2024-04-03 5:32 ` [PATCH v4 1/7] dt-bindings: PCI: rcar-gen4-pci-host: Add R-Car V4H compatible Yoshihiro Shimoda
2024-04-03 5:32 ` [PATCH v4 2/7] dt-bindings: PCI: rcar-gen4-pci-ep: " Yoshihiro Shimoda
2024-04-03 5:33 ` [PATCH v4 3/7] PCI: dwc: Add PCIE_PORT_{FORCE,LANE_SKEW} macros Yoshihiro Shimoda
2024-04-03 5:33 ` [PATCH v4 4/7] PCI: dwc: rcar-gen4: Add rcar_gen4_pcie_platdata Yoshihiro Shimoda
2024-04-03 5:33 ` [PATCH v4 5/7] PCI: dwc: rcar-gen4: Add .ltssm_enable() for other SoC support Yoshihiro Shimoda
2024-04-05 14:13 ` Geert Uytterhoeven
2024-04-08 1:11 ` Yoshihiro Shimoda
2024-04-03 5:33 ` Yoshihiro Shimoda [this message]
2024-04-03 5:33 ` [PATCH v4 7/7] misc: pci_endpoint_test: Document a policy about adding pci_device_id Yoshihiro Shimoda
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240403053304.3695096-7-yoshihiro.shimoda.uh@renesas.com \
--to=yoshihiro.shimoda.uh@renesas.com \
--cc=bhelgaas@google.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jingoohan1@gmail.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=kw@linux.com \
--cc=linux-pci@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=lpieralisi@kernel.org \
--cc=mani@kernel.org \
--cc=marek.vasut+renesas@gmail.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.