[PATCH v2 08/10] arm64: dts: microchip: sparx5_pcb135: drop LED unit addresses

From: Krzysztof Kozlowski <krzk@kernel.org>
To: Conor Dooley <conor@kernel.org>,
	Nicolas Ferre <nicolas.ferre@microchip.com>,
	Claudiu Beznea <claudiu.beznea@tuxon.dev>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Lars Povlsen <lars.povlsen@microchip.com>,
	Steen Hegelund <Steen.Hegelund@microchip.com>,
	Daniel Machon <daniel.machon@microchip.com>,
	UNGLinuxDriver@microchip.com,
	Bjarni Jonasson <bjarni.jonasson@microchip.com>,
	"David S. Miller" <davem@davemloft.net>,
	linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org
Cc: horatiu.vultur@microchip.com, steen.hegelund@microchip.com,
	Krzysztof Kozlowski <krzk@kernel.org>
Subject: [PATCH v2 08/10] arm64: dts: microchip: sparx5_pcb135: drop LED unit addresses
Date: Fri,  5 Apr 2024 21:04:17 +0200	[thread overview]
Message-ID: <20240405190419.74162-8-krzk@kernel.org> (raw)
In-Reply-To: <20240405190419.74162-1-krzk@kernel.org>

GPIO leds should not have unit addresses (no "reg" property), as
reported by dtc W=1 warnings:

  sparx5_pcb135_board.dtsi:18.9-22.5: Warning (unit_address_vs_reg): /leds/led@0: node has a unit name, but no reg or ranges property

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Changes in v2:
1. None
---
 .../boot/dts/microchip/sparx5_pcb135_board.dtsi  | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index 860975ffe0a1..20016efb3656 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -15,42 +15,42 @@ gpio-restart {
 
 	leds {
 		compatible = "gpio-leds";
-		led@0 {
+		led-0 {
 			label = "eth60:yellow";
 			gpios = <&sgpio_out1 28 0 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
-		led@1 {
+		led-1 {
 			label = "eth60:green";
 			gpios = <&sgpio_out1 28 1 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
-		led@2 {
+		led-2 {
 			label = "eth61:yellow";
 			gpios = <&sgpio_out1 29 0 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
-		led@3 {
+		led-3 {
 			label = "eth61:green";
 			gpios = <&sgpio_out1 29 1 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
-		led@4 {
+		led-4 {
 			label = "eth62:yellow";
 			gpios = <&sgpio_out1 30 0 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
-		led@5 {
+		led-5 {
 			label = "eth62:green";
 			gpios = <&sgpio_out1 30 1 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
-		led@6 {
+		led-6 {
 			label = "eth63:yellow";
 			gpios = <&sgpio_out1 31 0 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
-		led@7 {
+		led-7 {
 			label = "eth63:green";
 			gpios = <&sgpio_out1 31 1 GPIO_ACTIVE_LOW>;
 			default-state = "off";
-- 
2.34.1

