[PATCH 2/2] arm64: dts: rockchip: Add Radxa ZERO 3W/3E

[Jonas Karlman <jonas@kwiboo.se>]

The Radxa ZERO 3W/3E is an ultra-small, high-performance single board
computer based on the Rockchip RK3566, with a compact form factor and
rich interfaces.

The ZERO 3W and ZERO 3E are basically the same size and model, but
differ only in storage and network interfaces.

- eMMC (3W)
- SD-card (both)
- Ethernet (3E)
- WiFi/BT (3W)

This adds initial support for eMMC, SD-card, Ethernet, HDMI and USB.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
---
 .../dts/rockchip/rk3566-radxa-zero-3e.dts     |  41 ++
 .../dts/rockchip/rk3566-radxa-zero-3w.dts     |  26 +
 .../boot/dts/rockchip/rk3566-radxa-zero3.dtsi | 443 ++++++++++++++++++
 3 files changed, 510 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-radxa-zero-3e.dts
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-radxa-zero-3w.dts
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-radxa-zero3.dtsi

diff --git a/arch/arm64/boot/dts/rockchip/rk3566-radxa-zero-3e.dts b/arch/arm64/boot/dts/rockchip/rk3566-radxa-zero-3e.dts
new file mode 100644
index 000000000000..0826f7e99a81
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-radxa-zero-3e.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-radxa-zero3.dtsi"
+
+/ {
+	model = "Radxa ZERO 3E";
+	compatible = "radxa,zero-3e", "rockchip,rk3566";
+
+	aliases {
+		ethernet0 = &gmac1;
+	};
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_rgmii_bus
+		     &gmac1m1_clkinout>;
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-radxa-zero-3w.dts b/arch/arm64/boot/dts/rockchip/rk3566-radxa-zero-3w.dts
new file mode 100644
index 000000000000..be4ddce78378
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-radxa-zero-3w.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-radxa-zero3.dtsi"
+
+/ {
+	model = "Radxa ZERO 3W";
+	compatible = "radxa,zero-3w", "rockchip,rk3566";
+
+	aliases {
+		mmc1 = &sdhci;
+	};
+};
+
+&sdhci {
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-radxa-zero3.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-radxa-zero3.dtsi
new file mode 100644
index 000000000000..b69bc7b3addc
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-radxa-zero3.dtsi
@@ -0,0 +1,443 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &sdmmc0;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-green {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "on";
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&user_led2>;
+		};
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "d";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	vcc_sys: vcc-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc_1v8: vcc-1v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_1v8_p>;
+	};
+
+	vcc_3v3: vcc-3v3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	vcca_1v8: vcca-1v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcca_1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_1v8_p>;
+	};
+
+	vcca1v8_image: vcca1v8-image-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcca1v8_image";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_1v8_p>;
+	};
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu_npu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda_0v9>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1390000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk817: pmic@20 {
+		compatible = "rockchip,rk817";
+		reg = <0x20>;
+		#clock-cells = <1>;
+		clock-output-names = "rk817-clkout1", "rk817-clkout2";
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdd_gpu_npu: DCDC_REG2 {
+				regulator-name = "vdd_gpu_npu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc3v3_sys: DCDC_REG4 {
+				regulator-name = "vcc3v3_sys";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG1 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_1v8_p: LDO_REG7 {
+				regulator-name = "vcc_1v8_p";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc1v8_dvp: LDO_REG8 {
+				regulator-name = "vcc1v8_dvp";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc2v8_dvp: LDO_REG9 {
+				regulator-name = "vcc2v8_dvp";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2s0_8ch {
+	status = "okay";
+};
+
+&pinctrl {
+	leds {
+		user_led2: user-led2 {
+			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcca1v8_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_3v3>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
-- 
2.43.2