[PATCH 2/2] ARM: dts: owl-s500-roseapplepi: Add ethernet support

[Cristian Ciocaltea <cristian.ciocaltea@gmail.com>]

Add pinctrl configuration for enabling the Ethernet MAC on RoseapplePi
SBC. Additionally, provide the necessary properties for the generic S500
ethernet node in order to setup PHY and MDIO.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
---
 arch/arm/boot/dts/owl-s500-roseapplepi.dts | 56 ++++++++++++++++++++++
 1 file changed, 56 insertions(+)

diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
index b8c5db2344aa..bffabc7eaa50 100644
--- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts
+++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
@@ -225,6 +225,38 @@ bias1-pinconf {
 			bias-pull-down;
 		};
 	};
+
+	ethernet_pins: ethernet-pins {
+		txd01-pinmux {
+			groups = "rmii_txd0_mfp", "rmii_txd1_mfp";
+			function = "eth_rmii";
+		};
+
+		rxd01-pinmux {
+			groups = "rmii_rxd0_mfp", "rmii_rxd1_mfp";
+			function = "eth_rmii";
+		};
+
+		txen_rxer-pinmux {
+			groups = "rmii_txen_mfp", "rmii_rxen_mfp";
+			function = "eth_rmii";
+		};
+
+		crs_dv_ref_clk-pinmux {
+			groups = "rmii_crs_dv_mfp", "rmii_ref_clk_mfp";
+			function = "eth_rmii";
+		};
+
+		ref_clk-pinconf {
+			groups = "rmii_ref_clk_drv";
+			drive-strength = <2>;
+		};
+
+		phy_clk-pinmux {
+			groups = "clko_25m_mfp";
+			function = "clko_25m";
+		};
+	};
 };
 
 /* uSD */
@@ -241,6 +273,30 @@ &mmc0 {
 	vqmmc-supply = <&sd_vcc>;
 };
 
+&ethernet {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&eth_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&pinctrl 88 GPIO_ACTIVE_LOW>; /* GPIOC24 */
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <150000>;
+
+		eth_phy: ethernet-phy@3 {
+			reg = <0x3>;
+			max-speed = <100>;
+			interrupt-parent = <&sirq>;
+			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
 &twd_timer {
 	status = "okay";
 };
-- 
2.32.0