From: Lorenzo Bianconi <lorenzo@kernel.org>
To: jic23@kernel.org
Cc: linux-iio@vger.kernel.org, sean@geanix.com, martin@geanix.com,
rjones@gateworks.com, lorenzo.bianconi@redhat.com,
devicetree@vger.kernel.org
Subject: [PATCH 03/13] iio: imu: st_lsm6dsx: move irq related definitions in irq_config
Date: Sun, 6 Oct 2019 15:21:57 +0200 [thread overview]
Message-ID: <873559493f99be2a659f27da293f66a546598c2b.1570367532.git.lorenzo@kernel.org> (raw)
In-Reply-To: <cover.1570367532.git.lorenzo@kernel.org>
Group irq related definition in irq_config structure in
st_lsm6dsx_settings. This is a preliminary patch to move
OpenDrain/Active low registers in st_lsm6dsx_settings.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
---
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h | 22 +-
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 265 ++++++++++++-------
2 files changed, 179 insertions(+), 108 deletions(-)
diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
index fd02d0e184f3..873ec3b8fd69 100644
--- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
+++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
@@ -236,29 +236,21 @@ struct st_lsm6dsx_ext_dev_settings {
/**
* struct st_lsm6dsx_settings - ST IMU sensor settings
* @wai: Sensor WhoAmI default value.
- * @int1_addr: Control Register address for INT1
- * @int2_addr: Control Register address for INT2
* @reset_addr: register address for reset/reboot
* @max_fifo_size: Sensor max fifo length in FIFO words.
* @id: List of hw id/device name supported by the driver configuration.
* @channels: IIO channels supported by the device.
+ * @irq_config: interrupts related registers.
* @odr_table: Hw sensors odr table (Hz + val).
* @fs_table: Hw sensors gain table (gain + val).
* @decimator: List of decimator register info (addr + mask).
* @batch: List of FIFO batching register info (addr + mask).
- * @lir: Latched interrupt register info (addr + mask).
- * @clear_on_read: Clear on read register info (addr + mask).
* @fifo_ops: Sensor hw FIFO parameters.
* @ts_settings: Hw timer related settings.
* @shub_settings: i2c controller related settings.
*/
struct st_lsm6dsx_settings {
u8 wai;
- u8 int1_addr;
- u8 int2_addr;
- u8 int1_func_addr;
- u8 int2_func_addr;
- u8 int_func_mask;
u8 reset_addr;
u16 max_fifo_size;
struct {
@@ -269,12 +261,18 @@ struct st_lsm6dsx_settings {
const struct iio_chan_spec *chan;
int len;
} channels[2];
+ struct {
+ struct st_lsm6dsx_reg irq1;
+ struct st_lsm6dsx_reg irq2;
+ struct st_lsm6dsx_reg irq1_func;
+ struct st_lsm6dsx_reg irq2_func;
+ struct st_lsm6dsx_reg lir;
+ struct st_lsm6dsx_reg clear_on_read;
+ } irq_config;
struct st_lsm6dsx_odr_table_entry odr_table[2];
struct st_lsm6dsx_fs_table_entry fs_table[2];
struct st_lsm6dsx_reg decimator[ST_LSM6DSX_MAX_ID];
struct st_lsm6dsx_reg batch[ST_LSM6DSX_MAX_ID];
- struct st_lsm6dsx_reg lir;
- struct st_lsm6dsx_reg clear_on_read;
struct st_lsm6dsx_fifo_ops fifo_ops;
struct st_lsm6dsx_hw_ts_settings ts_settings;
struct st_lsm6dsx_shub_settings shub_settings;
@@ -359,9 +357,9 @@ struct st_lsm6dsx_hw {
u8 ts_sip;
u8 sip;
+ const struct st_lsm6dsx_reg *irq_routing;
u8 event_threshold;
u8 enable_event;
- struct st_lsm6dsx_reg irq_routing;
u8 *buff;
diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
index eac695663b6f..23d67caa24ed 100644
--- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
+++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
@@ -61,7 +61,6 @@
#include "st_lsm6dsx.h"
-#define ST_LSM6DSX_REG_FIFO_FTH_IRQ_MASK BIT(3)
#define ST_LSM6DSX_REG_WHOAMI_ADDR 0x0f
#define ST_LSM6DSX_REG_RESET_MASK BIT(0)
#define ST_LSM6DSX_REG_BOOT_MASK BIT(7)
@@ -97,8 +96,6 @@ static const struct iio_chan_spec st_lsm6ds0_gyro_channels[] = {
static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
{
.wai = 0x68,
- .int1_addr = 0x0c,
- .int2_addr = 0x0d,
.reset_addr = 0x22,
.max_fifo_size = 32,
.id = {
@@ -164,14 +161,19 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[2] = { IIO_DEGREE_TO_RAD(2000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0c,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ },
},
{
.wai = 0x69,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
- .int1_func_addr = 0x5e,
- .int2_func_addr = 0x5f,
- .int_func_mask = BIT(5),
.reset_addr = 0x12,
.max_fifo_size = 1365,
.id = {
@@ -238,6 +240,28 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x58,
+ .mask = BIT(0),
+ },
+ .irq1_func = {
+ .addr = 0x5e,
+ .mask = BIT(5),
+ },
+ .irq2_func = {
+ .addr = 0x5f,
+ .mask = BIT(5),
+ },
+ },
.decimator = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x08,
@@ -248,10 +272,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(5, 3),
},
},
- .lir = {
- .addr = 0x58,
- .mask = BIT(0),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_fifo,
@@ -297,11 +317,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
},
{
.wai = 0x69,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
- .int1_func_addr = 0x5e,
- .int2_func_addr = 0x5f,
- .int_func_mask = BIT(5),
.reset_addr = 0x12,
.max_fifo_size = 682,
.id = {
@@ -368,6 +383,28 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x58,
+ .mask = BIT(0),
+ },
+ .irq1_func = {
+ .addr = 0x5e,
+ .mask = BIT(5),
+ },
+ .irq2_func = {
+ .addr = 0x5f,
+ .mask = BIT(5),
+ },
+ },
.decimator = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x08,
@@ -378,10 +415,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(5, 3),
},
},
- .lir = {
- .addr = 0x58,
- .mask = BIT(0),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_fifo,
@@ -427,11 +460,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
},
{
.wai = 0x6a,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
- .int1_func_addr = 0x5e,
- .int2_func_addr = 0x5f,
- .int_func_mask = BIT(5),
.reset_addr = 0x12,
.max_fifo_size = 682,
.id = {
@@ -507,6 +535,28 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x58,
+ .mask = BIT(0),
+ },
+ .irq1_func = {
+ .addr = 0x5e,
+ .mask = BIT(5),
+ },
+ .irq2_func = {
+ .addr = 0x5f,
+ .mask = BIT(5),
+ },
+ },
.decimator = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x08,
@@ -517,10 +567,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(5, 3),
},
},
- .lir = {
- .addr = 0x58,
- .mask = BIT(0),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_fifo,
@@ -570,8 +616,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
},
{
.wai = 0x6c,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
.reset_addr = 0x12,
.max_fifo_size = 512,
.id = {
@@ -641,6 +685,24 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x56,
+ .mask = BIT(0),
+ },
+ .clear_on_read = {
+ .addr = 0x56,
+ .mask = BIT(6),
+ },
+ },
.batch = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x09,
@@ -651,14 +713,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(7, 4),
},
},
- .lir = {
- .addr = 0x56,
- .mask = BIT(0),
- },
- .clear_on_read = {
- .addr = 0x56,
- .mask = BIT(6),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_tagged_fifo,
@@ -711,11 +765,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
},
{
.wai = 0x6b,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
- .int1_func_addr = 0x5e,
- .int2_func_addr = 0x5f,
- .int_func_mask = BIT(5),
.reset_addr = 0x12,
.max_fifo_size = 512,
.id = {
@@ -782,6 +831,32 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x56,
+ .mask = BIT(0),
+ },
+ .clear_on_read = {
+ .addr = 0x56,
+ .mask = BIT(6),
+ },
+ .irq1_func = {
+ .addr = 0x5e,
+ .mask = BIT(5),
+ },
+ .irq2_func = {
+ .addr = 0x5f,
+ .mask = BIT(5),
+ },
+ },
.batch = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x09,
@@ -792,14 +867,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(7, 4),
},
},
- .lir = {
- .addr = 0x56,
- .mask = BIT(0),
- },
- .clear_on_read = {
- .addr = 0x56,
- .mask = BIT(6),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_tagged_fifo,
@@ -841,11 +908,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
},
{
.wai = 0x6b,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
- .int1_func_addr = 0x5e,
- .int2_func_addr = 0x5f,
- .int_func_mask = BIT(5),
.reset_addr = 0x12,
.max_fifo_size = 512,
.id = {
@@ -915,6 +977,32 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x56,
+ .mask = BIT(0),
+ },
+ .clear_on_read = {
+ .addr = 0x56,
+ .mask = BIT(6),
+ },
+ .irq1_func = {
+ .addr = 0x5e,
+ .mask = BIT(5),
+ },
+ .irq2_func = {
+ .addr = 0x5f,
+ .mask = BIT(5),
+ },
+ },
.batch = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x09,
@@ -925,14 +1013,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(7, 4),
},
},
- .lir = {
- .addr = 0x56,
- .mask = BIT(0),
- },
- .clear_on_read = {
- .addr = 0x56,
- .mask = BIT(6),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_tagged_fifo,
@@ -1281,7 +1361,7 @@ static int st_lsm6dsx_event_setup(struct st_lsm6dsx_hw *hw, int state)
int err;
u8 enable = 0;
- if (!hw->settings->int1_func_addr)
+ if (!hw->settings->irq_config.irq1_func.addr)
return -ENOTSUPP;
enable = state ? hw->settings->event_settings.enable_reg.mask : 0;
@@ -1293,12 +1373,11 @@ static int st_lsm6dsx_event_setup(struct st_lsm6dsx_hw *hw, int state)
if (err < 0)
return err;
- enable = state ? hw->irq_routing.mask : 0;
+ enable = state ? hw->irq_routing->mask : 0;
/* Enable wakeup interrupt */
- return regmap_update_bits(hw->regmap, hw->irq_routing.addr,
- hw->irq_routing.mask,
- enable);
+ return regmap_update_bits(hw->regmap, hw->irq_routing->addr,
+ hw->irq_routing->mask, enable);
}
static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
@@ -1527,7 +1606,9 @@ static int st_lsm6dsx_of_get_drdy_pin(struct st_lsm6dsx_hw *hw, int *drdy_pin)
return of_property_read_u32(np, "st,drdy-int-pin", drdy_pin);
}
-static int st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw, u8 *drdy_reg)
+static int
+st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw,
+ const struct st_lsm6dsx_reg **drdy_reg)
{
int err = 0, drdy_pin;
@@ -1541,14 +1622,12 @@ static int st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw, u8 *drdy_reg)
switch (drdy_pin) {
case 1:
- *drdy_reg = hw->settings->int1_addr;
- hw->irq_routing.addr = hw->settings->int1_func_addr;
- hw->irq_routing.mask = hw->settings->int_func_mask;
+ hw->irq_routing = &hw->settings->irq_config.irq1_func;
+ *drdy_reg = &hw->settings->irq_config.irq1;
break;
case 2:
- *drdy_reg = hw->settings->int2_addr;
- hw->irq_routing.addr = hw->settings->int2_func_addr;
- hw->irq_routing.mask = hw->settings->int_func_mask;
+ hw->irq_routing = &hw->settings->irq_config.irq2_func;
+ *drdy_reg = &hw->settings->irq_config.irq2;
break;
default:
dev_err(hw->dev, "unsupported data ready pin\n");
@@ -1644,7 +1723,7 @@ static int st_lsm6dsx_init_hw_timer(struct st_lsm6dsx_hw *hw)
static int st_lsm6dsx_init_device(struct st_lsm6dsx_hw *hw)
{
- u8 drdy_int_reg;
+ const struct st_lsm6dsx_reg *reg;
int err;
/* device sw reset */
@@ -1673,35 +1752,29 @@ static int st_lsm6dsx_init_device(struct st_lsm6dsx_hw *hw)
return err;
/* enable FIFO watermak interrupt */
- err = st_lsm6dsx_get_drdy_reg(hw, &drdy_int_reg);
+ err = st_lsm6dsx_get_drdy_reg(hw, ®);
if (err < 0)
return err;
- err = regmap_update_bits(hw->regmap, drdy_int_reg,
- ST_LSM6DSX_REG_FIFO_FTH_IRQ_MASK,
- FIELD_PREP(ST_LSM6DSX_REG_FIFO_FTH_IRQ_MASK,
- 1));
+ err = regmap_update_bits(hw->regmap, reg->addr, reg->mask,
+ ST_LSM6DSX_SHIFT_VAL(1, reg->mask));
if (err < 0)
return err;
/* enable Latched interrupts for device events */
- if (hw->settings->lir.addr) {
- unsigned int data;
-
- data = ST_LSM6DSX_SHIFT_VAL(1, hw->settings->lir.mask);
- err = regmap_update_bits(hw->regmap, hw->settings->lir.addr,
- hw->settings->lir.mask, data);
+ if (hw->settings->irq_config.lir.addr) {
+ reg = &hw->settings->irq_config.lir;
+ err = regmap_update_bits(hw->regmap, reg->addr, reg->mask,
+ ST_LSM6DSX_SHIFT_VAL(1, reg->mask));
if (err < 0)
return err;
/* enable clear on read for latched interrupts */
- if (hw->settings->clear_on_read.addr) {
- data = ST_LSM6DSX_SHIFT_VAL(1,
- hw->settings->clear_on_read.mask);
+ if (hw->settings->irq_config.clear_on_read.addr) {
+ reg = &hw->settings->irq_config.clear_on_read;
err = regmap_update_bits(hw->regmap,
- hw->settings->clear_on_read.addr,
- hw->settings->clear_on_read.mask,
- data);
+ reg->addr, reg->mask,
+ ST_LSM6DSX_SHIFT_VAL(1, reg->mask));
if (err < 0)
return err;
}
--
2.21.0
next prev parent reply other threads:[~2019-10-06 13:22 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-06 13:21 [PATCH 00/13] various st_lsm6dsx fixes and missing bits Lorenzo Bianconi
2019-10-06 13:21 ` [PATCH 01/13] iio: imu: st_lsm6dsx: use st_lsm6dsx_read_locked in st_lsm6dsx_report_motion_event Lorenzo Bianconi
2019-10-07 7:54 ` Sean Nyekjaer
2019-10-12 12:08 ` Jonathan Cameron
2019-10-06 13:21 ` [PATCH 02/13] iio: imu: st_lsm6dsx: add sanity check for read_fifo pointer Lorenzo Bianconi
2019-10-06 13:21 ` Lorenzo Bianconi [this message]
2019-10-07 7:54 ` [PATCH 03/13] iio: imu: st_lsm6dsx: move irq related definitions in irq_config Sean Nyekjaer
2019-10-12 12:13 ` Jonathan Cameron
2019-10-06 13:21 ` [PATCH 04/13] iio: imu: st_lsm6dsx: do not access active-low/open-drain regs if not supported Lorenzo Bianconi
2019-10-12 12:14 ` Jonathan Cameron
2019-10-06 13:21 ` [PATCH 05/13] iio: imu: st_lsm6dsx: move bdu/boot and reset register info in hw_settings Lorenzo Bianconi
2019-10-12 12:19 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 06/13] iio: imu: st_lsm6dsx: always check enable_reg in st_lsm6dsx_event_setup Lorenzo Bianconi
2019-10-07 7:55 ` Sean Nyekjaer
2019-10-12 12:21 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 07/13] iio: imu: st_lsm6dsx: rely on st_lsm6dsx_update_bits_locked configuring events Lorenzo Bianconi
2019-10-12 12:22 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 08/13] iio: imu: st_lsm6dsx: grab conf mutex in st_lsm6dsx_write_event_config Lorenzo Bianconi
2019-10-12 12:23 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 09/13] iio: imu: st_lsm6dsx: fix checkpatch warning Lorenzo Bianconi
2019-10-12 12:24 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 10/13] iio: imu: st_lsm6dsx: add wakeup_source in st_sensors_platform_data Lorenzo Bianconi
2019-10-12 12:25 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 11/13] iio: imu: st_lsm6dsx: add missing kernel documenation Lorenzo Bianconi
2019-10-07 7:56 ` Sean Nyekjaer
2019-10-12 12:26 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 12/13] dt-bindings: iio: imu: st_lsm6dsx: document missing wakeup-source property Lorenzo Bianconi
2019-10-07 7:56 ` Sean Nyekjaer
2019-10-15 20:34 ` Rob Herring
2019-10-06 13:22 ` [PATCH 13/13] iio: imu: st_lsm6dsx: enable wake-up event for LSM6DSO Lorenzo Bianconi
2019-10-12 12:28 ` Jonathan Cameron
2019-10-12 12:20 ` [PATCH 00/13] various st_lsm6dsx fixes and missing bits Jonathan Cameron
2019-10-12 12:26 ` Lorenzo Bianconi
2019-10-12 13:26 ` Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=873559493f99be2a659f27da293f66a546598c2b.1570367532.git.lorenzo@kernel.org \
--to=lorenzo@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jic23@kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=lorenzo.bianconi@redhat.com \
--cc=martin@geanix.com \
--cc=rjones@gateworks.com \
--cc=sean@geanix.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.