From: Michal Simek <monstr@monstr.eu>
To: SoC Team <soc@kernel.org>
Subject: [GIT PULL RESEND] arm64: dts: ZynqMP DT changes for v6.5
Date: Tue, 13 Jun 2023 13:48:57 +0200 [thread overview]
Message-ID: <CAHTX3d+2s_KmCnd=x5hydGb+LYoznAzYGTizvqqN2NFmrBurfw@mail.gmail.com> (raw)
Hi,
please pull these changes to your tree. Based on our chat I am sending
this request again because previous
one wasn't recorded properly in patchwork.
Thanks,
Michal
The following changes since commit ac9a78681b921877518763ba0e89202254349d1b:
Linux 6.4-rc1 (2023-05-07 13:34:35 -0700)
are available in the Git repository at:
https://github.com/Xilinx/linux-xlnx.git tags/zynqmp-dt-for-v6.5
for you to fetch changes up to 067bf44de11ceae0d2787c86127a39a67b2d60a6:
dt-bindings: usb: xilinx: Replace Manish by Piyush (2023-06-05 13:18:32 +0200)
----------------------------------------------------------------
arm64: ZynqMP DT changes for v6.5
Various small fixes and cleanups to be aligned with the latest dt-schema.
Other major changes are:
- Wire mali-400 gpu
- Change board name for zcu1275
- Use ethernet-phy-id to handle ETH phy reset properly
- Switch to amd.com emails
- Update people in DT bindings
----------------------------------------------------------------
Amit Kumar Mahapatra (2):
arm64: zynqmp: Add mtd partition for secure OS storage area
arm64: zynqmp: Set qspi tx-buswidth to 4
Ashok Reddy Soma (1):
arm64: zynqmp: Fix usb node drive strength and slew rate
Michal Simek (24):
dt-bindings: arm: xilinx: Change zc1275 board name to zcu1275
arm64: zynqmp: Change zc1275 board name to zcu1275
Revert "arm64: dts: zynqmp: Add address-cells property to
interrupt controllers"
arm64: zynqmp: Rename ams_ps/pl node names
arm64: zynqmp: Sync node name address with reg (mailbox)
arm64: zynqmp: Fix usb reset over bootmode pins on zcu100
arm64: zynqmp: Add dmas, dp, rtc, watchdogs and opp nodes for SOM
arm64: zynqmp: Use assigned-clock-rates for setting up SD clock in SOM
arm64: zynqmp: Add gpio labels for modepin gpio
arm64: zynqmp: Add pinctrl emmc description to SM-K26
arm64: zynqmp: Switch to ethernet-phy-id in kv260
arm64: zynqmp: Setup clock for DP and DPDMA
arm64: zynqmp: Enable DP driver for SOMs
arm64: zynqmp: Enable AMS on SOM and other zcu10x boards
arm64: zynqmp: Describe bus-width for SD card on KV260
arm64: zynqmp: Add phase tags marking
arm64: xilinx: Use zynqmp prefix for SOM dt overlays
dt-bindings: xilinx: Switch xilinx.com emails to amd.com
arm64: zynqmp: Convert kv260-revA overlay to ASCII text
arm64: zynqmp: Switch to amd.com emails
arm64: zynqmp: Describe TI phy as ethernet-phy-id
arm64: zynqmp: Used fixed-partitions for QSPI in k26
dt-bindings: xilinx: Remove Rajan, Jolly and Manish
dt-bindings: usb: xilinx: Replace Manish by Piyush
Parth Gajjar (2):
dt-bindings: gpu: mali-utgard: Add xlnx,zynqmp-mali compatible
arm64: zynqmp: Add mali-400 gpu node for zynqmp
Piyush Mehta (1):
arm64: zynqmp: Disable USB3.0 for zc1751-xm016-dc2
Radhey Shyam Pandey (1):
arm64: zynqmp: Add pmu interrupt-affinity
Sai Krishna Potthuri (1):
arm64: zynqmp: Add resets property to sdhci nodes
Srinivas Neeli (1):
arm64: zynqmp: Add linux,code for gpio button
Documentation/devicetree/bindings/arm/xilinx.yaml | 8 +-
Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml | 2 +-
Documentation/devicetree/bindings/clock/xlnx,clocking-wizard.yaml | 2 +-
Documentation/devicetree/bindings/clock/xlnx,versal-clk.yaml | 4 +-
Documentation/devicetree/bindings/crypto/xlnx,zynqmp-aes.yaml | 4 +-
Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.yaml
| 2 +-
Documentation/devicetree/bindings/fpga/xilinx-zynq-fpga-mgr.yaml | 2 +-
Documentation/devicetree/bindings/fpga/xlnx,versal-fpga.yaml | 2 +-
Documentation/devicetree/bindings/fpga/xlnx,zynqmp-pcap-fpga.yaml | 2 +-
Documentation/devicetree/bindings/gpio/gpio-zynq.yaml | 2 +-
Documentation/devicetree/bindings/gpio/xlnx,gpio-xilinx.yaml | 2 +-
Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml | 2 +-
Documentation/devicetree/bindings/gpu/arm,mali-utgard.yaml | 1 +
Documentation/devicetree/bindings/i2c/cdns,i2c-r1p10.yaml | 2 +-
Documentation/devicetree/bindings/mailbox/xlnx,zynqmp-ipi-mailbox.yaml
| 2 +-
Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml | 2 +-
Documentation/devicetree/bindings/memory-controllers/snps,dw-umctl2-ddrc.yaml
| 3 +-
Documentation/devicetree/bindings/memory-controllers/xlnx,zynq-ddrc-a05.yaml
| 3 +-
Documentation/devicetree/bindings/pci/xilinx-versal-cpm.yaml | 2 +-
Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.yaml | 2 +-
Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.yaml | 3 +-
Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.yaml | 2 +-
Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml | 2 +-
Documentation/devicetree/bindings/serial/cdns,uart.yaml | 2 +-
Documentation/devicetree/bindings/spi/spi-cadence.yaml | 2 +-
Documentation/devicetree/bindings/spi/spi-xilinx.yaml | 2 +-
Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.yaml | 2 +-
Documentation/devicetree/bindings/spi/xlnx,zynq-qspi.yaml | 2 +-
Documentation/devicetree/bindings/timer/cdns,ttc.yaml | 2 +-
Documentation/devicetree/bindings/usb/dwc3-xilinx.yaml | 2 +-
Documentation/devicetree/bindings/usb/xlnx,usb2.yaml | 2 +-
Documentation/devicetree/bindings/watchdog/xlnx,xps-timebase-wdt.yaml | 4 +-
arch/arm64/boot/dts/xilinx/Makefile | 18 +-
arch/arm64/boot/dts/xilinx/avnet-ultra96-rev1.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 21 +-
arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso | 28 +-
arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso | 22 +-
arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts | 327 +++++++++++++++-----
arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts | 4 +-
arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts | 6 +-
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts | 15 +-
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts | 12 +-
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts | 8 +-
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts | 4 +-
arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 38 ++-
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts | 48 ++-
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts | 27 +-
arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts | 48 ++-
arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts | 48 ++-
arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts | 35 ++-
arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts | 35 ++-
arch/arm64/boot/dts/xilinx/{zynqmp-zc1275-revA.dts =>
zynqmp-zcu1275-revA.dts} | 10 +-
arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 40 ++-
57 files changed, 633 insertions(+), 249 deletions(-)
rename arch/arm64/boot/dts/xilinx/{zynqmp-zc1275-revA.dts =>
zynqmp-zcu1275-revA.dts} (73%)
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Xilinx Microblaze
Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP ARM64 SoCs
U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP/Versal SoCs
next reply other threads:[~2023-06-13 11:49 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-06-13 11:48 Michal Simek [this message]
2023-06-20 21:21 ` [GIT PULL RESEND] arm64: dts: ZynqMP DT changes for v6.5 patchwork-bot+linux-soc
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAHTX3d+2s_KmCnd=x5hydGb+LYoznAzYGTizvqqN2NFmrBurfw@mail.gmail.com' \
--to=monstr@monstr.eu \
--cc=soc@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.