From: Min Li <lnimi@hotmail.com>
To: richardcochran@gmail.com, lee@kernel.org
Cc: linux-kernel@vger.kernel.org, netdev@vger.kernel.org,
Min Li <min.li.xe@renesas.com>
Subject: [PATCH net-next v2 1/1] ptp: clockmatrix: support 32-bit address space
Date: Thu, 9 Nov 2023 13:13:52 -0500 [thread overview]
Message-ID: <MW5PR03MB6932A4AAD4F612B45E9F6856A0AFA@MW5PR03MB6932.namprd03.prod.outlook.com> (raw)
From: Min Li <min.li.xe@renesas.com>
We used to assume 0x2010xxxx address. Now that
we need to access 0x2011xxxx address, we need
to support read/write the whole 32-bit address space.
Signed-off-by: Min Li <min.li.xe@renesas.com>
---
- Drop MAX_ABS_WRITE_PHASE_PICOSECONDS advised by Rahul
drivers/ptp/ptp_clockmatrix.c | 61 ++--
drivers/ptp/ptp_clockmatrix.h | 32 +-
include/linux/mfd/idt8a340_reg.h | 542 ++++++++++++++++---------------
3 files changed, 328 insertions(+), 307 deletions(-)
diff --git a/drivers/ptp/ptp_clockmatrix.c b/drivers/ptp/ptp_clockmatrix.c
index f6f9d4adce04..ff316aebff45 100644
--- a/drivers/ptp/ptp_clockmatrix.c
+++ b/drivers/ptp/ptp_clockmatrix.c
@@ -41,7 +41,7 @@ module_param(firmware, charp, 0);
static int _idtcm_adjfine(struct idtcm_channel *channel, long scaled_ppm);
static inline int idtcm_read(struct idtcm *idtcm,
- u16 module,
+ u32 module,
u16 regaddr,
u8 *buf,
u16 count)
@@ -50,7 +50,7 @@ static inline int idtcm_read(struct idtcm *idtcm,
}
static inline int idtcm_write(struct idtcm *idtcm,
- u16 module,
+ u32 module,
u16 regaddr,
u8 *buf,
u16 count)
@@ -62,7 +62,8 @@ static int contains_full_configuration(struct idtcm *idtcm,
const struct firmware *fw)
{
struct idtcm_fwrc *rec = (struct idtcm_fwrc *)fw->data;
- u16 scratch = IDTCM_FW_REG(idtcm->fw_ver, V520, SCRATCH);
+ u16 scratch = SCSR_ADDR(IDTCM_FW_REG(idtcm->fw_ver, V520, SCRATCH));
+ u16 gpio_control = SCSR_ADDR(GPIO_USER_CONTROL);
s32 full_count;
s32 count = 0;
u16 regaddr;
@@ -70,8 +71,8 @@ static int contains_full_configuration(struct idtcm *idtcm,
s32 len;
/* 4 bytes skipped every 0x80 */
- full_count = (scratch - GPIO_USER_CONTROL) -
- ((scratch >> 7) - (GPIO_USER_CONTROL >> 7)) * 4;
+ full_count = (scratch - gpio_control) -
+ ((scratch >> 7) - (gpio_control >> 7)) * 4;
/* If the firmware contains 'full configuration' SM_RESET can be used
* to ensure proper configuration.
@@ -88,7 +89,7 @@ static int contains_full_configuration(struct idtcm *idtcm,
rec++;
/* Top (status registers) and bottom are read-only */
- if (regaddr < GPIO_USER_CONTROL || regaddr >= scratch)
+ if (regaddr < gpio_control || regaddr >= scratch)
continue;
/* Page size 128, last 4 bytes of page skipped */
@@ -506,8 +507,8 @@ static int _sync_pll_output(struct idtcm *idtcm,
{
int err;
u8 val;
- u16 sync_ctrl0;
- u16 sync_ctrl1;
+ u32 sync_ctrl0;
+ u32 sync_ctrl1;
u8 temp;
if (qn == 0 && qn_plus_1 == 0)
@@ -576,21 +577,21 @@ static int _sync_pll_output(struct idtcm *idtcm,
/* PLL5 can have OUT8 as second additional output. */
if (pll == 5 && qn_plus_1 != 0) {
- err = idtcm_read(idtcm, 0, HW_Q8_CTRL_SPARE,
+ err = idtcm_read(idtcm, HW_Q8_CTRL_SPARE, 0,
&temp, sizeof(temp));
if (err)
return err;
temp &= ~(Q9_TO_Q8_SYNC_TRIG);
- err = idtcm_write(idtcm, 0, HW_Q8_CTRL_SPARE,
+ err = idtcm_write(idtcm, HW_Q8_CTRL_SPARE, 0,
&temp, sizeof(temp));
if (err)
return err;
temp |= Q9_TO_Q8_SYNC_TRIG;
- err = idtcm_write(idtcm, 0, HW_Q8_CTRL_SPARE,
+ err = idtcm_write(idtcm, HW_Q8_CTRL_SPARE, 0,
&temp, sizeof(temp));
if (err)
return err;
@@ -598,21 +599,21 @@ static int _sync_pll_output(struct idtcm *idtcm,
/* PLL6 can have OUT11 as second additional output. */
if (pll == 6 && qn_plus_1 != 0) {
- err = idtcm_read(idtcm, 0, HW_Q11_CTRL_SPARE,
+ err = idtcm_read(idtcm, HW_Q11_CTRL_SPARE, 0,
&temp, sizeof(temp));
if (err)
return err;
temp &= ~(Q10_TO_Q11_SYNC_TRIG);
- err = idtcm_write(idtcm, 0, HW_Q11_CTRL_SPARE,
+ err = idtcm_write(idtcm, HW_Q11_CTRL_SPARE, 0,
&temp, sizeof(temp));
if (err)
return err;
temp |= Q10_TO_Q11_SYNC_TRIG;
- err = idtcm_write(idtcm, 0, HW_Q11_CTRL_SPARE,
+ err = idtcm_write(idtcm, HW_Q11_CTRL_SPARE, 0,
&temp, sizeof(temp));
if (err)
return err;
@@ -637,7 +638,7 @@ static int idtcm_sync_pps_output(struct idtcm_channel *channel)
u8 temp;
u16 output_mask = channel->output_mask;
- err = idtcm_read(idtcm, 0, HW_Q8_CTRL_SPARE,
+ err = idtcm_read(idtcm, HW_Q8_CTRL_SPARE, 0,
&temp, sizeof(temp));
if (err)
return err;
@@ -646,7 +647,7 @@ static int idtcm_sync_pps_output(struct idtcm_channel *channel)
Q9_TO_Q8_FANOUT_AND_CLOCK_SYNC_ENABLE_MASK)
out8_mux = 1;
- err = idtcm_read(idtcm, 0, HW_Q11_CTRL_SPARE,
+ err = idtcm_read(idtcm, HW_Q11_CTRL_SPARE, 0,
&temp, sizeof(temp));
if (err)
return err;
@@ -1303,14 +1304,14 @@ static int idtcm_load_firmware(struct idtcm *idtcm,
err = 0;
/* Top (status registers) and bottom are read-only */
- if (regaddr < GPIO_USER_CONTROL || regaddr >= scratch)
+ if (regaddr < SCSR_ADDR(GPIO_USER_CONTROL) || regaddr >= scratch)
continue;
/* Page size 128, last 4 bytes of page skipped */
if ((loaddr > 0x7b && loaddr <= 0x7f) || loaddr > 0xfb)
continue;
- err = idtcm_write(idtcm, regaddr, 0, &val, sizeof(val));
+ err = idtcm_write(idtcm, SCSR_BASE, regaddr, &val, sizeof(val));
}
if (err)
@@ -1395,6 +1396,20 @@ static int idtcm_set_pll_mode(struct idtcm_channel *channel,
struct idtcm *idtcm = channel->idtcm;
int err;
u8 dpll_mode;
+ u8 timeout = 0;
+
+ /* Setup WF/WP timer for phase pull-in to work correctly */
+ err = idtcm_write(idtcm, channel->dpll_n, DPLL_WF_TIMER,
+ &timeout, sizeof(timeout));
+ if (err)
+ return err;
+
+ if (mode == PLL_MODE_WRITE_PHASE)
+ timeout = 160;
+ err = idtcm_write(idtcm, channel->dpll_n, DPLL_WP_TIMER,
+ &timeout, sizeof(timeout));
+ if (err)
+ return err;
err = idtcm_read(idtcm, channel->dpll_n,
IDTCM_FW_REG(idtcm->fw_ver, V520, DPLL_MODE),
@@ -1705,10 +1720,14 @@ static s32 idtcm_getmaxphase(struct ptp_clock_info *ptp __always_unused)
}
/*
- * Internal function for implementing support for write phase offset
+ * Maximum absolute value for write phase offset in picoseconds
*
* @channel: channel
* @delta_ns: delta in nanoseconds
+ *
+ * Destination signed register is 32-bit register in resolution of 50ps
+ *
+ * 0x7fffffff * 50 = 2147483647 * 50 = 107374182350
*/
static int _idtcm_adjphase(struct idtcm_channel *channel, s32 delta_ns)
{
@@ -1717,6 +1736,7 @@ static int _idtcm_adjphase(struct idtcm_channel *channel, s32 delta_ns)
u8 i;
u8 buf[4] = {0};
s32 phase_50ps;
+ s64 offset_ps;
if (channel->mode != PTP_PLL_MODE_WRITE_PHASE) {
err = channel->configure_write_phase(channel);
@@ -1724,7 +1744,8 @@ static int _idtcm_adjphase(struct idtcm_channel *channel, s32 delta_ns)
return err;
}
- phase_50ps = div_s64((s64)delta_ns * 1000, 50);
+ offset_ps = (s64)delta_ns * 1000;
+ phase_50ps = div_s64(offset_ps, 50);
for (i = 0; i < 4; i++) {
buf[i] = phase_50ps & 0xff;
diff --git a/drivers/ptp/ptp_clockmatrix.h b/drivers/ptp/ptp_clockmatrix.h
index 7c17c4f7f573..ad39dc6decdf 100644
--- a/drivers/ptp/ptp_clockmatrix.h
+++ b/drivers/ptp/ptp_clockmatrix.h
@@ -54,21 +54,9 @@
#define LOCK_TIMEOUT_MS (2000)
#define LOCK_POLL_INTERVAL_MS (10)
-#define IDTCM_MAX_WRITE_COUNT (512)
-
#define PHASE_PULL_IN_MAX_PPB (144000)
#define PHASE_PULL_IN_MIN_THRESHOLD_NS (2)
-/*
- * Return register address based on passed in firmware version
- */
-#define IDTCM_FW_REG(FW, VER, REG) (((FW) < (VER)) ? (REG) : (REG##_##VER))
-enum fw_version {
- V_DEFAULT = 0,
- V487 = 1,
- V520 = 2,
-};
-
/* PTP PLL Mode */
enum ptp_pll_mode {
PTP_PLL_MODE_MIN = 0,
@@ -84,16 +72,16 @@ struct idtcm_channel {
struct ptp_clock_info caps;
struct ptp_clock *ptp_clock;
struct idtcm *idtcm;
- u16 dpll_phase;
- u16 dpll_freq;
- u16 dpll_n;
- u16 dpll_ctrl_n;
- u16 dpll_phase_pull_in;
- u16 tod_read_primary;
- u16 tod_read_secondary;
- u16 tod_write;
- u16 tod_n;
- u16 hw_dpll_n;
+ u32 dpll_phase;
+ u32 dpll_freq;
+ u32 dpll_n;
+ u32 dpll_ctrl_n;
+ u32 dpll_phase_pull_in;
+ u32 tod_read_primary;
+ u32 tod_read_secondary;
+ u32 tod_write;
+ u32 tod_n;
+ u32 hw_dpll_n;
u8 sync_src;
enum ptp_pll_mode mode;
int (*configure_write_frequency)(struct idtcm_channel *channel);
diff --git a/include/linux/mfd/idt8a340_reg.h b/include/linux/mfd/idt8a340_reg.h
index 0c706085c205..b680a0eb5f68 100644
--- a/include/linux/mfd/idt8a340_reg.h
+++ b/include/linux/mfd/idt8a340_reg.h
@@ -7,20 +7,20 @@
#ifndef HAVE_IDT8A340_REG
#define HAVE_IDT8A340_REG
-#define PAGE_ADDR_BASE 0x0000
-#define PAGE_ADDR 0x00fc
+#define SCSR_BASE 0x20100000
+#define SCSR_ADDR(x) ((x) & 0xffff)
-#define HW_REVISION 0x8180
+#define HW_REVISION 0x20108180
#define REV_ID 0x007a
-#define HW_DPLL_0 (0x8a00)
-#define HW_DPLL_1 (0x8b00)
-#define HW_DPLL_2 (0x8c00)
-#define HW_DPLL_3 (0x8d00)
-#define HW_DPLL_4 (0x8e00)
-#define HW_DPLL_5 (0x8f00)
-#define HW_DPLL_6 (0x9000)
-#define HW_DPLL_7 (0x9100)
+#define HW_DPLL_0 (0x20108a00)
+#define HW_DPLL_1 (0x20108b00)
+#define HW_DPLL_2 (0x20108c00)
+#define HW_DPLL_3 (0x20108d00)
+#define HW_DPLL_4 (0x20108e00)
+#define HW_DPLL_5 (0x20108f00)
+#define HW_DPLL_6 (0x20109000)
+#define HW_DPLL_7 (0x20109100)
#define HW_DPLL_TOD_SW_TRIG_ADDR__0 (0x080)
#define HW_DPLL_TOD_CTRL_1 (0x089)
@@ -28,22 +28,22 @@
#define HW_DPLL_TOD_OVR__0 (0x098)
#define HW_DPLL_TOD_OUT_0__0 (0x0B0)
-#define HW_Q0_Q1_CH_SYNC_CTRL_0 (0xa740)
-#define HW_Q0_Q1_CH_SYNC_CTRL_1 (0xa741)
-#define HW_Q2_Q3_CH_SYNC_CTRL_0 (0xa742)
-#define HW_Q2_Q3_CH_SYNC_CTRL_1 (0xa743)
-#define HW_Q4_Q5_CH_SYNC_CTRL_0 (0xa744)
-#define HW_Q4_Q5_CH_SYNC_CTRL_1 (0xa745)
-#define HW_Q6_Q7_CH_SYNC_CTRL_0 (0xa746)
-#define HW_Q6_Q7_CH_SYNC_CTRL_1 (0xa747)
-#define HW_Q8_CH_SYNC_CTRL_0 (0xa748)
-#define HW_Q8_CH_SYNC_CTRL_1 (0xa749)
-#define HW_Q9_CH_SYNC_CTRL_0 (0xa74a)
-#define HW_Q9_CH_SYNC_CTRL_1 (0xa74b)
-#define HW_Q10_CH_SYNC_CTRL_0 (0xa74c)
-#define HW_Q10_CH_SYNC_CTRL_1 (0xa74d)
-#define HW_Q11_CH_SYNC_CTRL_0 (0xa74e)
-#define HW_Q11_CH_SYNC_CTRL_1 (0xa74f)
+#define HW_Q0_Q1_CH_SYNC_CTRL_0 (0x2010a740)
+#define HW_Q0_Q1_CH_SYNC_CTRL_1 (0x2010a741)
+#define HW_Q2_Q3_CH_SYNC_CTRL_0 (0x2010a742)
+#define HW_Q2_Q3_CH_SYNC_CTRL_1 (0x2010a743)
+#define HW_Q4_Q5_CH_SYNC_CTRL_0 (0x2010a744)
+#define HW_Q4_Q5_CH_SYNC_CTRL_1 (0x2010a745)
+#define HW_Q6_Q7_CH_SYNC_CTRL_0 (0x2010a746)
+#define HW_Q6_Q7_CH_SYNC_CTRL_1 (0x2010a747)
+#define HW_Q8_CH_SYNC_CTRL_0 (0x2010a748)
+#define HW_Q8_CH_SYNC_CTRL_1 (0x2010a749)
+#define HW_Q9_CH_SYNC_CTRL_0 (0x2010a74a)
+#define HW_Q9_CH_SYNC_CTRL_1 (0x2010a74b)
+#define HW_Q10_CH_SYNC_CTRL_0 (0x2010a74c)
+#define HW_Q10_CH_SYNC_CTRL_1 (0x2010a74d)
+#define HW_Q11_CH_SYNC_CTRL_0 (0x2010a74e)
+#define HW_Q11_CH_SYNC_CTRL_1 (0x2010a74f)
#define SYNC_SOURCE_DPLL0_TOD_PPS 0x14
#define SYNC_SOURCE_DPLL1_TOD_PPS 0x15
@@ -58,8 +58,8 @@
#define SYNCTRL1_Q1_DIV_SYNC_TRIG BIT(1)
#define SYNCTRL1_Q0_DIV_SYNC_TRIG BIT(0)
-#define HW_Q8_CTRL_SPARE (0xa7d4)
-#define HW_Q11_CTRL_SPARE (0xa7ec)
+#define HW_Q8_CTRL_SPARE (0x2010a7d4)
+#define HW_Q11_CTRL_SPARE (0x2010a7ec)
/**
* Select FOD5 as sync_trigger for Q8 divider.
@@ -95,12 +95,12 @@
*/
#define Q10_TO_Q11_FANOUT_AND_CLOCK_SYNC_ENABLE_MASK (BIT(0) | BIT(2))
-#define RESET_CTRL 0xc000
+#define RESET_CTRL 0x2010c000
#define SM_RESET 0x0012
#define SM_RESET_V520 0x0013
#define SM_RESET_CMD 0x5A
-#define GENERAL_STATUS 0xc014
+#define GENERAL_STATUS 0x2010c014
#define BOOT_STATUS 0x0000
#define HW_REV_ID 0x000A
#define BOND_ID 0x000B
@@ -115,7 +115,7 @@
#define PRODUCT_ID 0x001e
#define OTP_SCSR_CONFIG_SELECT 0x0022
-#define STATUS 0xc03c
+#define STATUS 0x2010c03c
#define DPLL0_STATUS 0x0018
#define DPLL1_STATUS 0x0019
#define DPLL2_STATUS 0x001a
@@ -138,60 +138,62 @@
#define USER_GPIO0_TO_7_STATUS 0x008a
#define USER_GPIO8_TO_15_STATUS 0x008b
-#define GPIO_USER_CONTROL 0xc160
+#define GPIO_USER_CONTROL 0x2010c160
#define GPIO0_TO_7_OUT 0x0000
#define GPIO8_TO_15_OUT 0x0001
#define GPIO0_TO_7_OUT_V520 0x0002
#define GPIO8_TO_15_OUT_V520 0x0003
-#define STICKY_STATUS_CLEAR 0xc164
-
-#define GPIO_TOD_NOTIFICATION_CLEAR 0xc16c
-
-#define ALERT_CFG 0xc188
-
-#define SYS_DPLL_XO 0xc194
-
-#define SYS_APLL 0xc19c
-
-#define INPUT_0 0xc1b0
-#define INPUT_1 0xc1c0
-#define INPUT_2 0xc1d0
-#define INPUT_3 0xc200
-#define INPUT_4 0xc210
-#define INPUT_5 0xc220
-#define INPUT_6 0xc230
-#define INPUT_7 0xc240
-#define INPUT_8 0xc250
-#define INPUT_9 0xc260
-#define INPUT_10 0xc280
-#define INPUT_11 0xc290
-#define INPUT_12 0xc2a0
-#define INPUT_13 0xc2b0
-#define INPUT_14 0xc2c0
-#define INPUT_15 0xc2d0
-
-#define REF_MON_0 0xc2e0
-#define REF_MON_1 0xc2ec
-#define REF_MON_2 0xc300
-#define REF_MON_3 0xc30c
-#define REF_MON_4 0xc318
-#define REF_MON_5 0xc324
-#define REF_MON_6 0xc330
-#define REF_MON_7 0xc33c
-#define REF_MON_8 0xc348
-#define REF_MON_9 0xc354
-#define REF_MON_10 0xc360
-#define REF_MON_11 0xc36c
-#define REF_MON_12 0xc380
-#define REF_MON_13 0xc38c
-#define REF_MON_14 0xc398
-#define REF_MON_15 0xc3a4
-
-#define DPLL_0 0xc3b0
+#define STICKY_STATUS_CLEAR 0x2010c164
+
+#define GPIO_TOD_NOTIFICATION_CLEAR 0x2010c16c
+
+#define ALERT_CFG 0x2010c188
+
+#define SYS_DPLL_XO 0x2010c194
+
+#define SYS_APLL 0x2010c19c
+
+#define INPUT_0 0x2010c1b0
+#define INPUT_1 0x2010c1c0
+#define INPUT_2 0x2010c1d0
+#define INPUT_3 0x2010c200
+#define INPUT_4 0x2010c210
+#define INPUT_5 0x2010c220
+#define INPUT_6 0x2010c230
+#define INPUT_7 0x2010c240
+#define INPUT_8 0x2010c250
+#define INPUT_9 0x2010c260
+#define INPUT_10 0x2010c280
+#define INPUT_11 0x2010c290
+#define INPUT_12 0x2010c2a0
+#define INPUT_13 0x2010c2b0
+#define INPUT_14 0x2010c2c0
+#define INPUT_15 0x2010c2d0
+
+#define REF_MON_0 0x2010c2e0
+#define REF_MON_1 0x2010c2ec
+#define REF_MON_2 0x2010c300
+#define REF_MON_3 0x2010c30c
+#define REF_MON_4 0x2010c318
+#define REF_MON_5 0x2010c324
+#define REF_MON_6 0x2010c330
+#define REF_MON_7 0x2010c33c
+#define REF_MON_8 0x2010c348
+#define REF_MON_9 0x2010c354
+#define REF_MON_10 0x2010c360
+#define REF_MON_11 0x2010c36c
+#define REF_MON_12 0x2010c380
+#define REF_MON_13 0x2010c38c
+#define REF_MON_14 0x2010c398
+#define REF_MON_15 0x2010c3a4
+
+#define DPLL_0 0x2010c3b0
#define DPLL_CTRL_REG_0 0x0002
#define DPLL_CTRL_REG_1 0x0003
#define DPLL_CTRL_REG_2 0x0004
+#define DPLL_WF_TIMER 0x002c
+#define DPLL_WP_TIMER 0x002e
#define DPLL_TOD_SYNC_CFG 0x0031
#define DPLL_COMBO_SLAVE_CFG_0 0x0032
#define DPLL_COMBO_SLAVE_CFG_1 0x0033
@@ -200,69 +202,69 @@
#define DPLL_PHASE_MEASUREMENT_CFG 0x0036
#define DPLL_MODE 0x0037
#define DPLL_MODE_V520 0x003B
-#define DPLL_1 0xc400
-#define DPLL_2 0xc438
-#define DPLL_2_V520 0xc43c
-#define DPLL_3 0xc480
-#define DPLL_4 0xc4b8
-#define DPLL_4_V520 0xc4bc
-#define DPLL_5 0xc500
-#define DPLL_6 0xc538
-#define DPLL_6_V520 0xc53c
-#define DPLL_7 0xc580
-#define SYS_DPLL 0xc5b8
-#define SYS_DPLL_V520 0xc5bc
-
-#define DPLL_CTRL_0 0xc600
+#define DPLL_1 0x2010c400
+#define DPLL_2 0x2010c438
+#define DPLL_2_V520 0x2010c43c
+#define DPLL_3 0x2010c480
+#define DPLL_4 0x2010c4b8
+#define DPLL_4_V520 0x2010c4bc
+#define DPLL_5 0x2010c500
+#define DPLL_6 0x2010c538
+#define DPLL_6_V520 0x2010c53c
+#define DPLL_7 0x2010c580
+#define SYS_DPLL 0x2010c5b8
+#define SYS_DPLL_V520 0x2010c5bc
+
+#define DPLL_CTRL_0 0x2010c600
#define DPLL_CTRL_DPLL_MANU_REF_CFG 0x0001
#define DPLL_CTRL_DPLL_FOD_FREQ 0x001c
#define DPLL_CTRL_COMBO_MASTER_CFG 0x003a
-#define DPLL_CTRL_1 0xc63c
-#define DPLL_CTRL_2 0xc680
-#define DPLL_CTRL_3 0xc6bc
-#define DPLL_CTRL_4 0xc700
-#define DPLL_CTRL_5 0xc73c
-#define DPLL_CTRL_6 0xc780
-#define DPLL_CTRL_7 0xc7bc
-#define SYS_DPLL_CTRL 0xc800
-
-#define DPLL_PHASE_0 0xc818
+#define DPLL_CTRL_1 0x2010c63c
+#define DPLL_CTRL_2 0x2010c680
+#define DPLL_CTRL_3 0x2010c6bc
+#define DPLL_CTRL_4 0x2010c700
+#define DPLL_CTRL_5 0x2010c73c
+#define DPLL_CTRL_6 0x2010c780
+#define DPLL_CTRL_7 0x2010c7bc
+#define SYS_DPLL_CTRL 0x2010c800
+
+#define DPLL_PHASE_0 0x2010c818
/* Signed 42-bit FFO in units of 2^(-53) */
#define DPLL_WR_PHASE 0x0000
-#define DPLL_PHASE_1 0xc81c
-#define DPLL_PHASE_2 0xc820
-#define DPLL_PHASE_3 0xc824
-#define DPLL_PHASE_4 0xc828
-#define DPLL_PHASE_5 0xc82c
-#define DPLL_PHASE_6 0xc830
-#define DPLL_PHASE_7 0xc834
-
-#define DPLL_FREQ_0 0xc838
+#define DPLL_PHASE_1 0x2010c81c
+#define DPLL_PHASE_2 0x2010c820
+#define DPLL_PHASE_3 0x2010c824
+#define DPLL_PHASE_4 0x2010c828
+#define DPLL_PHASE_5 0x2010c82c
+#define DPLL_PHASE_6 0x2010c830
+#define DPLL_PHASE_7 0x2010c834
+
+#define DPLL_FREQ_0 0x2010c838
/* Signed 42-bit FFO in units of 2^(-53) */
#define DPLL_WR_FREQ 0x0000
-#define DPLL_FREQ_1 0xc840
-#define DPLL_FREQ_2 0xc848
-#define DPLL_FREQ_3 0xc850
-#define DPLL_FREQ_4 0xc858
-#define DPLL_FREQ_5 0xc860
-#define DPLL_FREQ_6 0xc868
-#define DPLL_FREQ_7 0xc870
-
-#define DPLL_PHASE_PULL_IN_0 0xc880
+#define DPLL_FREQ_1 0x2010c840
+#define DPLL_FREQ_2 0x2010c848
+#define DPLL_FREQ_3 0x2010c850
+#define DPLL_FREQ_4 0x2010c858
+#define DPLL_FREQ_5 0x2010c860
+#define DPLL_FREQ_6 0x2010c868
+#define DPLL_FREQ_7 0x2010c870
+
+#define DPLL_PHASE_PULL_IN_0 0x2010c880
#define PULL_IN_OFFSET 0x0000 /* Signed 32 bit */
#define PULL_IN_SLOPE_LIMIT 0x0004 /* Unsigned 24 bit */
#define PULL_IN_CTRL 0x0007
-#define DPLL_PHASE_PULL_IN_1 0xc888
-#define DPLL_PHASE_PULL_IN_2 0xc890
-#define DPLL_PHASE_PULL_IN_3 0xc898
-#define DPLL_PHASE_PULL_IN_4 0xc8a0
-#define DPLL_PHASE_PULL_IN_5 0xc8a8
-#define DPLL_PHASE_PULL_IN_6 0xc8b0
-#define DPLL_PHASE_PULL_IN_7 0xc8b8
-
-#define GPIO_CFG 0xc8c0
+#define DPLL_PHASE_PULL_IN_1 0x2010c888
+#define DPLL_PHASE_PULL_IN_2 0x2010c890
+#define DPLL_PHASE_PULL_IN_3 0x2010c898
+#define DPLL_PHASE_PULL_IN_4 0x2010c8a0
+#define DPLL_PHASE_PULL_IN_5 0x2010c8a8
+#define DPLL_PHASE_PULL_IN_6 0x2010c8b0
+#define DPLL_PHASE_PULL_IN_7 0x2010c8b8
+
+#define GPIO_CFG 0x2010c8c0
#define GPIO_CFG_GBL 0x0000
-#define GPIO_0 0xc8c2
+#define GPIO_0 0x2010c8c2
#define GPIO_DCO_INC_DEC 0x0000
#define GPIO_OUT_CTRL_0 0x0001
#define GPIO_OUT_CTRL_1 0x0002
@@ -281,25 +283,25 @@
#define GPIO_TOD_NOTIFICATION_CFG 0x000f
#define GPIO_CTRL 0x0010
#define GPIO_CTRL_V520 0x0011
-#define GPIO_1 0xc8d4
-#define GPIO_2 0xc8e6
-#define GPIO_3 0xc900
-#define GPIO_4 0xc912
-#define GPIO_5 0xc924
-#define GPIO_6 0xc936
-#define GPIO_7 0xc948
-#define GPIO_8 0xc95a
-#define GPIO_9 0xc980
-#define GPIO_10 0xc992
-#define GPIO_11 0xc9a4
-#define GPIO_12 0xc9b6
-#define GPIO_13 0xc9c8
-#define GPIO_14 0xc9da
-#define GPIO_15 0xca00
-
-#define OUT_DIV_MUX 0xca12
-#define OUTPUT_0 0xca14
-#define OUTPUT_0_V520 0xca20
+#define GPIO_1 0x2010c8d4
+#define GPIO_2 0x2010c8e6
+#define GPIO_3 0x2010c900
+#define GPIO_4 0x2010c912
+#define GPIO_5 0x2010c924
+#define GPIO_6 0x2010c936
+#define GPIO_7 0x2010c948
+#define GPIO_8 0x2010c95a
+#define GPIO_9 0x2010c980
+#define GPIO_10 0x2010c992
+#define GPIO_11 0x2010c9a4
+#define GPIO_12 0x2010c9b6
+#define GPIO_13 0x2010c9c8
+#define GPIO_14 0x2010c9da
+#define GPIO_15 0x2010ca00
+
+#define OUT_DIV_MUX 0x2010ca12
+#define OUTPUT_0 0x2010ca14
+#define OUTPUT_0_V520 0x2010ca20
/* FOD frequency output divider value */
#define OUT_DIV 0x0000
#define OUT_DUTY_CYCLE_HIGH 0x0004
@@ -307,88 +309,88 @@
#define OUT_CTRL_1 0x0009
/* Phase adjustment in FOD cycles */
#define OUT_PHASE_ADJ 0x000c
-#define OUTPUT_1 0xca24
-#define OUTPUT_1_V520 0xca30
-#define OUTPUT_2 0xca34
-#define OUTPUT_2_V520 0xca40
-#define OUTPUT_3 0xca44
-#define OUTPUT_3_V520 0xca50
-#define OUTPUT_4 0xca54
-#define OUTPUT_4_V520 0xca60
-#define OUTPUT_5 0xca64
-#define OUTPUT_5_V520 0xca80
-#define OUTPUT_6 0xca80
-#define OUTPUT_6_V520 0xca90
-#define OUTPUT_7 0xca90
-#define OUTPUT_7_V520 0xcaa0
-#define OUTPUT_8 0xcaa0
-#define OUTPUT_8_V520 0xcab0
-#define OUTPUT_9 0xcab0
-#define OUTPUT_9_V520 0xcac0
-#define OUTPUT_10 0xcac0
-#define OUTPUT_10_V520 0xcad0
-#define OUTPUT_11 0xcad0
-#define OUTPUT_11_V520 0xcae0
-
-#define SERIAL 0xcae0
-#define SERIAL_V520 0xcaf0
-
-#define PWM_ENCODER_0 0xcb00
-#define PWM_ENCODER_1 0xcb08
-#define PWM_ENCODER_2 0xcb10
-#define PWM_ENCODER_3 0xcb18
-#define PWM_ENCODER_4 0xcb20
-#define PWM_ENCODER_5 0xcb28
-#define PWM_ENCODER_6 0xcb30
-#define PWM_ENCODER_7 0xcb38
-#define PWM_DECODER_0 0xcb40
-#define PWM_DECODER_1 0xcb48
-#define PWM_DECODER_1_V520 0xcb4a
-#define PWM_DECODER_2 0xcb50
-#define PWM_DECODER_2_V520 0xcb54
-#define PWM_DECODER_3 0xcb58
-#define PWM_DECODER_3_V520 0xcb5e
-#define PWM_DECODER_4 0xcb60
-#define PWM_DECODER_4_V520 0xcb68
-#define PWM_DECODER_5 0xcb68
-#define PWM_DECODER_5_V520 0xcb80
-#define PWM_DECODER_6 0xcb70
-#define PWM_DECODER_6_V520 0xcb8a
-#define PWM_DECODER_7 0xcb80
-#define PWM_DECODER_7_V520 0xcb94
-#define PWM_DECODER_8 0xcb88
-#define PWM_DECODER_8_V520 0xcb9e
-#define PWM_DECODER_9 0xcb90
-#define PWM_DECODER_9_V520 0xcba8
-#define PWM_DECODER_10 0xcb98
-#define PWM_DECODER_10_V520 0xcbb2
-#define PWM_DECODER_11 0xcba0
-#define PWM_DECODER_11_V520 0xcbbc
-#define PWM_DECODER_12 0xcba8
-#define PWM_DECODER_12_V520 0xcbc6
-#define PWM_DECODER_13 0xcbb0
-#define PWM_DECODER_13_V520 0xcbd0
-#define PWM_DECODER_14 0xcbb8
-#define PWM_DECODER_14_V520 0xcbda
-#define PWM_DECODER_15 0xcbc0
-#define PWM_DECODER_15_V520 0xcbe4
-#define PWM_USER_DATA 0xcbc8
-#define PWM_USER_DATA_V520 0xcbf0
-
-#define TOD_0 0xcbcc
-#define TOD_0_V520 0xcc00
+#define OUTPUT_1 0x2010ca24
+#define OUTPUT_1_V520 0x2010ca30
+#define OUTPUT_2 0x2010ca34
+#define OUTPUT_2_V520 0x2010ca40
+#define OUTPUT_3 0x2010ca44
+#define OUTPUT_3_V520 0x2010ca50
+#define OUTPUT_4 0x2010ca54
+#define OUTPUT_4_V520 0x2010ca60
+#define OUTPUT_5 0x2010ca64
+#define OUTPUT_5_V520 0x2010ca80
+#define OUTPUT_6 0x2010ca80
+#define OUTPUT_6_V520 0x2010ca90
+#define OUTPUT_7 0x2010ca90
+#define OUTPUT_7_V520 0x2010caa0
+#define OUTPUT_8 0x2010caa0
+#define OUTPUT_8_V520 0x2010cab0
+#define OUTPUT_9 0x2010cab0
+#define OUTPUT_9_V520 0x2010cac0
+#define OUTPUT_10 0x2010cac0
+#define OUTPUT_10_V520 0x2010cad0
+#define OUTPUT_11 0x2010cad0
+#define OUTPUT_11_V520 0x2010cae0
+
+#define SERIAL 0x2010cae0
+#define SERIAL_V520 0x2010caf0
+
+#define PWM_ENCODER_0 0x2010cb00
+#define PWM_ENCODER_1 0x2010cb08
+#define PWM_ENCODER_2 0x2010cb10
+#define PWM_ENCODER_3 0x2010cb18
+#define PWM_ENCODER_4 0x2010cb20
+#define PWM_ENCODER_5 0x2010cb28
+#define PWM_ENCODER_6 0x2010cb30
+#define PWM_ENCODER_7 0x2010cb38
+#define PWM_DECODER_0 0x2010cb40
+#define PWM_DECODER_1 0x2010cb48
+#define PWM_DECODER_1_V520 0x2010cb4a
+#define PWM_DECODER_2 0x2010cb50
+#define PWM_DECODER_2_V520 0x2010cb54
+#define PWM_DECODER_3 0x2010cb58
+#define PWM_DECODER_3_V520 0x2010cb5e
+#define PWM_DECODER_4 0x2010cb60
+#define PWM_DECODER_4_V520 0x2010cb68
+#define PWM_DECODER_5 0x2010cb68
+#define PWM_DECODER_5_V520 0x2010cb80
+#define PWM_DECODER_6 0x2010cb70
+#define PWM_DECODER_6_V520 0x2010cb8a
+#define PWM_DECODER_7 0x2010cb80
+#define PWM_DECODER_7_V520 0x2010cb94
+#define PWM_DECODER_8 0x2010cb88
+#define PWM_DECODER_8_V520 0x2010cb9e
+#define PWM_DECODER_9 0x2010cb90
+#define PWM_DECODER_9_V520 0x2010cba8
+#define PWM_DECODER_10 0x2010cb98
+#define PWM_DECODER_10_V520 0x2010cbb2
+#define PWM_DECODER_11 0x2010cba0
+#define PWM_DECODER_11_V520 0x2010cbbc
+#define PWM_DECODER_12 0x2010cba8
+#define PWM_DECODER_12_V520 0x2010cbc6
+#define PWM_DECODER_13 0x2010cbb0
+#define PWM_DECODER_13_V520 0x2010cbd0
+#define PWM_DECODER_14 0x2010cbb8
+#define PWM_DECODER_14_V520 0x2010cbda
+#define PWM_DECODER_15 0x2010cbc0
+#define PWM_DECODER_15_V520 0x2010cbe4
+#define PWM_USER_DATA 0x2010cbc8
+#define PWM_USER_DATA_V520 0x2010cbf0
+
+#define TOD_0 0x2010cbcc
+#define TOD_0_V520 0x2010cc00
/* Enable TOD counter, output channel sync and even-PPS mode */
#define TOD_CFG 0x0000
#define TOD_CFG_V520 0x0001
-#define TOD_1 0xcbce
-#define TOD_1_V520 0xcc02
-#define TOD_2 0xcbd0
-#define TOD_2_V520 0xcc04
-#define TOD_3 0xcbd2
-#define TOD_3_V520 0xcc06
-
-#define TOD_WRITE_0 0xcc00
-#define TOD_WRITE_0_V520 0xcc10
+#define TOD_1 0x2010cbce
+#define TOD_1_V520 0x2010cc02
+#define TOD_2 0x2010cbd0
+#define TOD_2_V520 0x2010cc04
+#define TOD_3 0x2010cbd2
+#define TOD_3_V520 0x2010cc06
+
+#define TOD_WRITE_0 0x2010cc00
+#define TOD_WRITE_0_V520 0x2010cc10
/* 8-bit subns, 32-bit ns, 48-bit seconds */
#define TOD_WRITE 0x0000
/* Counter increments after TOD write is completed */
@@ -397,15 +399,15 @@
#define TOD_WRITE_SELECT_CFG_0 0x000d
/* TOD write trigger selection */
#define TOD_WRITE_CMD 0x000f
-#define TOD_WRITE_1 0xcc10
-#define TOD_WRITE_1_V520 0xcc20
-#define TOD_WRITE_2 0xcc20
-#define TOD_WRITE_2_V520 0xcc30
-#define TOD_WRITE_3 0xcc30
-#define TOD_WRITE_3_V520 0xcc40
-
-#define TOD_READ_PRIMARY_0 0xcc40
-#define TOD_READ_PRIMARY_0_V520 0xcc50
+#define TOD_WRITE_1 0x2010cc10
+#define TOD_WRITE_1_V520 0x2010cc20
+#define TOD_WRITE_2 0x2010cc20
+#define TOD_WRITE_2_V520 0x2010cc30
+#define TOD_WRITE_3 0x2010cc30
+#define TOD_WRITE_3_V520 0x2010cc40
+
+#define TOD_READ_PRIMARY_0 0x2010cc40
+#define TOD_READ_PRIMARY_0_V520 0x2010cc50
/* 8-bit subns, 32-bit ns, 48-bit seconds */
#define TOD_READ_PRIMARY_BASE 0x0000
/* Counter increments after TOD write is completed */
@@ -415,15 +417,15 @@
/* Read trigger selection */
#define TOD_READ_PRIMARY_CMD 0x000e
#define TOD_READ_PRIMARY_CMD_V520 0x000f
-#define TOD_READ_PRIMARY_1 0xcc50
-#define TOD_READ_PRIMARY_1_V520 0xcc60
-#define TOD_READ_PRIMARY_2 0xcc60
-#define TOD_READ_PRIMARY_2_V520 0xcc80
-#define TOD_READ_PRIMARY_3 0xcc80
-#define TOD_READ_PRIMARY_3_V520 0xcc90
-
-#define TOD_READ_SECONDARY_0 0xcc90
-#define TOD_READ_SECONDARY_0_V520 0xcca0
+#define TOD_READ_PRIMARY_1 0x2010cc50
+#define TOD_READ_PRIMARY_1_V520 0x2010cc60
+#define TOD_READ_PRIMARY_2 0x2010cc60
+#define TOD_READ_PRIMARY_2_V520 0x2010cc80
+#define TOD_READ_PRIMARY_3 0x2010cc80
+#define TOD_READ_PRIMARY_3_V520 0x2010cc90
+
+#define TOD_READ_SECONDARY_0 0x2010cc90
+#define TOD_READ_SECONDARY_0_V520 0x2010cca0
/* 8-bit subns, 32-bit ns, 48-bit seconds */
#define TOD_READ_SECONDARY_BASE 0x0000
/* Counter increments after TOD write is completed */
@@ -434,30 +436,30 @@
#define TOD_READ_SECONDARY_CMD 0x000e
#define TOD_READ_SECONDARY_CMD_V520 0x000f
-#define TOD_READ_SECONDARY_1 0xcca0
-#define TOD_READ_SECONDARY_1_V520 0xccb0
-#define TOD_READ_SECONDARY_2 0xccb0
-#define TOD_READ_SECONDARY_2_V520 0xccc0
-#define TOD_READ_SECONDARY_3 0xccc0
-#define TOD_READ_SECONDARY_3_V520 0xccd0
+#define TOD_READ_SECONDARY_1 0x2010cca0
+#define TOD_READ_SECONDARY_1_V520 0x2010ccb0
+#define TOD_READ_SECONDARY_2 0x2010ccb0
+#define TOD_READ_SECONDARY_2_V520 0x2010ccc0
+#define TOD_READ_SECONDARY_3 0x2010ccc0
+#define TOD_READ_SECONDARY_3_V520 0x2010ccd0
-#define OUTPUT_TDC_CFG 0xccd0
-#define OUTPUT_TDC_CFG_V520 0xcce0
-#define OUTPUT_TDC_0 0xcd00
-#define OUTPUT_TDC_1 0xcd08
-#define OUTPUT_TDC_2 0xcd10
-#define OUTPUT_TDC_3 0xcd18
-#define INPUT_TDC 0xcd20
+#define OUTPUT_TDC_CFG 0x2010ccd0
+#define OUTPUT_TDC_CFG_V520 0x2010cce0
+#define OUTPUT_TDC_0 0x2010cd00
+#define OUTPUT_TDC_1 0x2010cd08
+#define OUTPUT_TDC_2 0x2010cd10
+#define OUTPUT_TDC_3 0x2010cd18
+#define INPUT_TDC 0x2010cd20
-#define SCRATCH 0xcf50
-#define SCRATCH_V520 0xcf4c
+#define SCRATCH 0x2010cf50
+#define SCRATCH_V520 0x2010cf4c
-#define EEPROM 0xcf68
-#define EEPROM_V520 0xcf64
+#define EEPROM 0x2010cf68
+#define EEPROM_V520 0x2010cf64
-#define OTP 0xcf70
+#define OTP 0x2010cf70
-#define BYTE 0xcf80
+#define BYTE 0x2010cf80
/* Bit definitions for the MAJ_REL register */
#define MAJOR_SHIFT (1)
@@ -665,6 +667,16 @@
#define DPLL_STATE_MASK (0xf)
#define DPLL_STATE_SHIFT (0x0)
+/*
+ * Return register address based on passed in firmware version
+ */
+#define IDTCM_FW_REG(FW, VER, REG) (((FW) < (VER)) ? (REG) : (REG##_##VER))
+enum fw_version {
+ V_DEFAULT = 0,
+ V487 = 1,
+ V520 = 2,
+};
+
/* Values of DPLL_N.DPLL_MODE.PLL_MODE */
enum pll_mode {
PLL_MODE_MIN = 0,
--
2.39.2
next reply other threads:[~2023-11-09 18:14 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-11-09 18:13 Min Li [this message]
2023-11-09 22:25 ` [PATCH net-next v2 1/1] ptp: clockmatrix: support 32-bit address space Simon Horman
2023-11-09 23:34 ` Rahul Rameshbabu
2023-11-11 11:03 ` kernel test robot
2023-11-20 10:54 ` Dan Carpenter
2023-11-10 22:10 kernel test robot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=MW5PR03MB6932A4AAD4F612B45E9F6856A0AFA@MW5PR03MB6932.namprd03.prod.outlook.com \
--to=lnimi@hotmail.com \
--cc=lee@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=min.li.xe@renesas.com \
--cc=netdev@vger.kernel.org \
--cc=richardcochran@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.