From: Robin Murphy <robin.murphy@arm.com> To: heiko@sntech.de Cc: linux-rockchip@lists.infradead.org, linux-arm-kernel@lists.infradead.org Subject: [PATCH] arm64: dts: rockchip: Add nanopi4 bluetooth Date: Fri, 15 Feb 2019 00:02:34 +0000 [thread overview] Message-ID: <a7c0fae925a838ad5bb540f4302614a94472b437.1550188024.git.robin.murphy@arm.com> (raw) Describe the Bluetooth portion of the Ampak combo module - this is either an AP6356S or an AP6212 depending on the board variant, but there are no relevant compatibility differences between the two. Signed-off-by: Robin Murphy <robin.murphy@arm.com> --- .../boot/dts/rockchip/rk3399-nanopi4.dtsi | 31 +++++++++++++++++-- 1 file changed, 29 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi index 2d304d2df62e..db48e986b361 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi @@ -218,7 +218,7 @@ rk808: pmic@1b { compatible = "rockchip,rk808"; reg = <0x1b>; - clock-output-names = "xin32k", "rk808-clkout2"; + clock-output-names = "xin32k", "rtc_clko_wifi"; #clock-cells = <1>; interrupt-parent = <&gpio1>; interrupts = <21 IRQ_TYPE_LEVEL_LOW>; @@ -501,7 +501,20 @@ }; }; - sdio-pwrseq { + sdio { + bt_host_wake_l: bt-host-wake-l { + rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + bt_reg_on_h: bt-reg-on-h { + /* external pullup to VCC1V8_PMUPLL */ + rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + bt_wake_l: bt-wake-l { + rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + wifi_reg_on_h: wifi-reg_on-h { rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; }; @@ -621,6 +634,20 @@ pinctrl-names = "default"; pinctrl-0 = <&uart0_xfer &uart0_rts &uart0_cts>; status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + clocks = <&rk808 1>; + clock-names = "lpo"; + device-wakeup-gpios = <&gpio2 RK_PD2 GPIO_ACTIVE_HIGH>; + host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>; + shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>; + max-speed = <4000000>; + pinctrl-names = "default"; + pinctrl-0 = <&bt_reg_on_h &bt_host_wake_l &bt_wake_l>; + vbat-supply = <&vcc3v3_sys>; + vddio-supply = <&vcc_1v8>; + }; }; &uart2 { -- 2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: Robin Murphy <robin.murphy@arm.com> To: heiko@sntech.de Cc: linux-rockchip@lists.infradead.org, linux-arm-kernel@lists.infradead.org Subject: [PATCH] arm64: dts: rockchip: Add nanopi4 bluetooth Date: Fri, 15 Feb 2019 00:02:34 +0000 [thread overview] Message-ID: <a7c0fae925a838ad5bb540f4302614a94472b437.1550188024.git.robin.murphy@arm.com> (raw) Describe the Bluetooth portion of the Ampak combo module - this is either an AP6356S or an AP6212 depending on the board variant, but there are no relevant compatibility differences between the two. Signed-off-by: Robin Murphy <robin.murphy@arm.com> --- .../boot/dts/rockchip/rk3399-nanopi4.dtsi | 31 +++++++++++++++++-- 1 file changed, 29 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi index 2d304d2df62e..db48e986b361 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi @@ -218,7 +218,7 @@ rk808: pmic@1b { compatible = "rockchip,rk808"; reg = <0x1b>; - clock-output-names = "xin32k", "rk808-clkout2"; + clock-output-names = "xin32k", "rtc_clko_wifi"; #clock-cells = <1>; interrupt-parent = <&gpio1>; interrupts = <21 IRQ_TYPE_LEVEL_LOW>; @@ -501,7 +501,20 @@ }; }; - sdio-pwrseq { + sdio { + bt_host_wake_l: bt-host-wake-l { + rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + bt_reg_on_h: bt-reg-on-h { + /* external pullup to VCC1V8_PMUPLL */ + rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + bt_wake_l: bt-wake-l { + rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + wifi_reg_on_h: wifi-reg_on-h { rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; }; @@ -621,6 +634,20 @@ pinctrl-names = "default"; pinctrl-0 = <&uart0_xfer &uart0_rts &uart0_cts>; status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + clocks = <&rk808 1>; + clock-names = "lpo"; + device-wakeup-gpios = <&gpio2 RK_PD2 GPIO_ACTIVE_HIGH>; + host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>; + shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>; + max-speed = <4000000>; + pinctrl-names = "default"; + pinctrl-0 = <&bt_reg_on_h &bt_host_wake_l &bt_wake_l>; + vbat-supply = <&vcc3v3_sys>; + vddio-supply = <&vcc_1v8>; + }; }; &uart2 { -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2019-02-15 0:02 UTC|newest] Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-02-15 0:02 Robin Murphy [this message] 2019-02-15 0:02 ` [PATCH] arm64: dts: rockchip: Add nanopi4 bluetooth Robin Murphy 2019-02-15 9:07 ` Heiko Stübner 2019-02-15 9:07 ` Heiko Stübner
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=a7c0fae925a838ad5bb540f4302614a94472b437.1550188024.git.robin.murphy@arm.com \ --to=robin.murphy@arm.com \ --cc=heiko@sntech.de \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-rockchip@lists.infradead.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.