Linux kernel regressions
 help / color / Atom feed
From: Chukun Pan <amadeus@jmu.edu.cn>
To: maxime@cerno.tech
Cc: amadeus@jmu.edu.cn, devicetree@vger.kernel.org,
	jernej.skrabec@siol.net, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-sunxi@lists.linux.dev,
	lkft-triage@lists.linaro.org, naresh.kamboju@linaro.org,
	regressions@lists.linux.dev, robh+dt@kernel.org, wens@csie.org
Subject: [PATCH v2 1/2] arm64: dts: allwinner: h5: Add NanoPi R1S H5 support
Date: Mon, 17 May 2021 00:35:22 +0800
Message-ID: <20210516163523.9484-2-amadeus@jmu.edu.cn> (raw)
In-Reply-To: <20210516163523.9484-1-amadeus@jmu.edu.cn>

The NanoPi R1S H5 is a open source board made by FriendlyElec.
It has the following features:

- Allwinner H5, Quad-core Cortex-A53
- 512MB DDR3 RAM
- 10/100/1000M Ethernet x 2
- RTL8189ETV WiFi 802.11b/g/n
- USB 2.0 host port (A)
- MicroSD Slot
- Serial Debug Port
- 5V 2A DC power-supply

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts | 195 ++++++++++++++++++
 2 files changed, 196 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 41ce680e5f8d..a96d9d2d8dd8 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -25,6 +25,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-libretech-all-h3-it.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-libretech-all-h5-cc.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-r1s-h5.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
new file mode 100644
index 000000000000..55bcdf8d1a07
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 Chukun Pan <amadeus@jmu.edu.cn>
+ *
+ * Based on sun50i-h5-nanopi-neo-plus2.dts, which is:
+ *   Copyright (C) 2017 Antony Antony <antony@phenome.org>
+ *   Copyright (C) 2016 ARM Ltd.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+#include "sun50i-h5-cpu-opp.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "FriendlyARM NanoPi R1S H5";
+	compatible = "friendlyarm,nanopi-r1s-h5", "allwinner,sun50i-h5";
+
+	aliases {
+		ethernet0 = &emac;
+		ethernet1 = &rtl8189etv;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_LAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	r-gpio-keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usb0_vbus: usb0-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+		status = "okay";
+	};
+
+	vdd_cpux: gpio-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0x1>;
+		states = <1100000 0x0>, <1300000 0x1>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpux>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "microchip,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	rtl8189etv: sdio_wifi@1 {
+		reg = <1>;
+	};
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	/* USB Type-A port's VBUS is always on */
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
-- 
2.17.1


  reply index

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <20210503142905.21468-1-amadeus@jmu.edu.cn>
2021-05-11  5:21 ` [PATCH " Naresh Kamboju
2021-05-11  8:18   ` Maxime Ripard
2021-05-16 16:35     ` [PATCH v2 0/2] Add support for NanoPi R1S H5 Chukun Pan
2021-05-16 16:35       ` Chukun Pan [this message]
2021-05-16 16:35       ` [PATCH v2 2/2] dt-bindings: arm: Add " Chukun Pan
2021-05-18 14:01       ` [PATCH v2 0/2] Add support for " Maxime Ripard

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210516163523.9484-2-amadeus@jmu.edu.cn \
    --to=amadeus@jmu.edu.cn \
    --cc=devicetree@vger.kernel.org \
    --cc=jernej.skrabec@siol.net \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-sunxi@lists.linux.dev \
    --cc=lkft-triage@lists.linaro.org \
    --cc=maxime@cerno.tech \
    --cc=naresh.kamboju@linaro.org \
    --cc=regressions@lists.linux.dev \
    --cc=robh+dt@kernel.org \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux kernel regressions

Archives are clonable:
	git clone --mirror https://lore.kernel.org/regressions/0 regressions/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 regressions regressions/ https://lore.kernel.org/regressions \
		regressions@lists.linux.dev
	public-inbox-index regressions

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/dev.linux.lists.regressions


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git