From: Bert Vermeulen <bert@biot.com>
To: Marc Zyngier <maz@kernel.org>, Linus Walleij <linus.walleij@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
linux-kernel <linux-kernel@vger.kernel.org>,
Linux ARM <linux-arm-kernel@lists.infradead.org>,
Arnd Bergmann <arnd@arndb.de>, Olof Johansson <olof@lixom.net>,
SoC Team <soc@kernel.org>, Rob Herring <robh+dt@kernel.org>,
John Crispin <john@phrozen.org>, Felix Fietkau <nbd@nbd.name>
Subject: Re: [PATCH 3/5] ARM: dts: Add basic support for EcoNet EN7523
Date: Sun, 1 Aug 2021 11:07:48 +0200 [thread overview]
Message-ID: <0fe113c6-4160-fd3c-488d-53d40b6043ee@biot.com> (raw)
In-Reply-To: <87y29n26po.wl-maz@kernel.org>
On 7/30/21 4:53 PM, Marc Zyngier wrote:
> On Fri, 30 Jul 2021 15:31:36 +0100,
> Linus Walleij <linus.walleij@linaro.org> wrote:
>>
>> Paging Marc Z and Catalin just so they can see this:
>>
>> On Fri, Jul 30, 2021 at 3:49 PM Bert Vermeulen <bert@biot.com> wrote:
>>
>> > From: John Crispin <john@phrozen.org>
>> >
>> > Add basic support for EcoNet EN7523, enough for booting to console.
>> >
>> > The UART is basically 8250-compatible, except for the clock selection.
>> > A clock-frequency value is synthesized to get this to run at 115200 bps.
>> >
>> > Signed-off-by: John Crispin <john@phrozen.org>
>> > Signed-off-by: Bert Vermeulen <bert@biot.com>
>> (...)
>> > + gic: interrupt-controller@09000000 {
>> > + compatible = "arm,gic-v3";
>> > + interrupt-controller;
>> > + #interrupt-cells = <3>;
>> > + #address-cells = <1>;
>> > + #size-cells = <1>;
>> > + reg = <0x09000000 0x20000>,
>> > + <0x09080000 0x80000>;
>> > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
>> > +
>> > + its: gic-its@09020000 {
>> > + compatible = "arm,gic-v3-its";
>> > + msi-controller;
>> > + #msi-cell = <1>;
>> > + reg = <0x090200000 0x20000>;
>> > + };
>> > + };
>>
>> Yup GICv3 on ARM32-only silicon.
>
> Hey, why not. But that's very unlikely, as Cortex-A7 doesn't have a
> GICv3 CPU interface built in (it only has the memory mapped version),
> and A53/57 were the first CPUs to ever support GICv3. I don't believe
> the description of the CPU in the DT is accurate.
>
> Bert, please send a kernel boot log.
At the bottom of this mail.
>> > + timer {
>> > + compatible = "arm,armv8-timer";
>> > + interrupt-parent = <&gic>;
>> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
>
> Copy paste bug. These are not valid intspecs for GICv3.
FWIW all these were taken verbatim from the vendor's SDK. Not that this
makes them necessarily correct :)
>> > + clock-frequency = <25000000>;
>> > + };
>>
>> Also arm,armv8-timer on ARM32-only silicon.
>
> Probably because that's not what it actually is. My bet is on A53 with
> a crippled firmware.
kernel boot log:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.14.0-rc3-00042-g3af70c6f8e95-dirty
(bert@sumner) (arm-linux-gnueabi-gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0,
GNU ld (GNU Binutils for Ubuntu) 2.34) #392 SMP Sun Aug 1 10:28:13 CEST 2021
[ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] OF: fdt: Machine model: econet,en7523
[ 0.000000] earlycon: uart8250 at MMIO32 0x1fbf0000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x0000000083ffffff]
[ 0.000000] node 0: [mem 0x0000000084000000-0x00000000849fffff]
[ 0.000000] node 0: [mem 0x0000000084a00000-0x0000000084afffff]
[ 0.000000] node 0: [mem 0x0000000084b00000-0x0000000084bfffff]
[ 0.000000] node 0: [mem 0x0000000084c00000-0x0000000084ffffff]
[ 0.000000] node 0: [mem 0x0000000085000000-0x00000000869fffff]
[ 0.000000] node 0: [mem 0x0000000086a00000-0x0000000086afffff]
[ 0.000000] node 0: [mem 0x0000000086b00000-0x0000000086bfffff]
[ 0.000000] node 0: [mem 0x0000000086c00000-0x0000000086cfffff]
[ 0.000000] node 0: [mem 0x0000000086d00000-0x0000000086dfffff]
[ 0.000000] node 0: [mem 0x0000000086e00000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30604 r8192 d22644 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0x1fbf0000
console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 461316K/524288K available (7168K kernel code, 312K
rwdata, 1488K rodata, 8192K init, 142K bss, 62972K reserved, 0K
cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10
jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GICv3: 256 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x09080000
[ 0.000000] random: get_random_bytes called from start_kernel+0x484/0x628
with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff
max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every
4398046511100ns
[ 0.008791] Switching to timer-based delay loop, resolution 40ns
[ 0.015454] Calibrating delay loop (skipped), value calculated using
timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.026833] pid_max: default: 32768 minimum: 301
[ 0.032013] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes,
linear)
[ 0.040047] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes, linear)
[ 0.049172] CPU: Testing write buffer coherency: ok
[ 0.054780] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.061362] Setting up static identity map for 0x80100000 - 0x80100060
[ 0.068667] rcu: Hierarchical SRCU implementation.
[ 0.074290] gic-its@09020000: unable to locate ITS domain
[ 0.080461] smp: Bringing up secondary CPUs ...
[ 0.085769] smp: Brought up 1 node, 1 CPU
[ 0.090179] SMP: Total of 1 processors activated (50.00 BogoMIPS).
[ 0.097013] CPU: All CPU(s) started in SVC mode.
[ 0.103634] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.114499] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.122380] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.129153] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.137265] thermal_sys: Registered thermal governor 'step_wise'
[ 0.137333] No ATAGs?
[ 0.153205] iommu: Default domain type: Translated
[ 0.158713] usbcore: registered new interface driver usbfs
[ 0.164769] usbcore: registered new interface driver hub
[ 0.170660] usbcore: registered new device driver usb
[ 0.176704] NET: Registered PF_ATMPVC protocol family
[ 0.182296] NET: Registered PF_ATMSVC protocol family
[ 0.188055] clocksource: Switched to clocksource arch_sys_counter
[ 0.195462] NET: Registered PF_INET protocol family
[ 0.200971] IP idents hash table entries: 8192 (order: 4, 65536 bytes,
linear)
[ 0.209452] tcp_listen_portaddr_hash hash table entries: 512 (order: 0,
6144 bytes, linear)
[ 0.218713] TCP established hash table entries: 4096 (order: 2, 16384
bytes, linear)
[ 0.227251] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.235158] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.242212] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.249416] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.257205] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.263464] PCI: CLS 0 bytes, default 64
[ 0.348846] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.360684] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.367197] ntfs: driver 2.1.32 [Flags: R/W DEBUG].
[ 0.372785] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.598557] io scheduler mq-deadline registered
[ 0.603555] io scheduler kyber registered
[ 0.619475] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.626838] printk: console [ttyS0] disabled
[ 0.631671] 1fbf0000.serial: ttyS0 at MMIO 0x1fbf0000 (irq = 28,
base_baud = 115200) is a 8250
[ 0.641169] printk: console [ttyS0] enabled
[ 0.641169] printk: console [ttyS0] enabled
[ 0.649943] printk: bootconsole [uart8250] disabled
[ 0.649943] printk: bootconsole [uart8250] disabled
[ 0.706413] brd: module loaded
[ 0.709758] PPP generic driver version 2.4.2
[ 0.714097] PPP BSD Compression module registered
[ 0.718832] PPP Deflate Compression module registered
[ 0.723877] NET: Registered PF_PPPOX protocol family
[ 0.728989] usbcore: registered new interface driver cdc_acm
[ 0.734648] cdc_acm: USB Abstract Control Model driver for USB modems and
ISDN adapters
[ 0.742712] usbcore: registered new interface driver usbserial_generic
[ 0.749278] usbserial: USB Serial support registered for generic
[ 0.755299] usbcore: registered new interface driver cypress_m8
[ 0.761234] usbserial: USB Serial support registered for DeLorme
Earthmate USB
[ 0.768476] usbserial: USB Serial support registered for HID->COM RS232
Adapter
[ 0.775790] usbserial: USB Serial support registered for Nokia CA-42 V2
Adapter
[ 0.783121] usbcore: registered new interface driver ftdi_sio
[ 0.788889] usbserial: USB Serial support registered for FTDI USB Serial
Device
[ 0.796272] hid: raw HID events driver (C) Jiri Kosina
[ 0.801492] usbcore: registered new interface driver usbhid
[ 0.807061] usbhid: USB HID core driver
[ 0.811617] IPv4 over IPsec tunneling driver
[ 0.816458] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[ 0.822866] Initializing XFRM netlink socket
[ 0.827522] NET: Registered PF_INET6 protocol family
[ 0.955712] Segment Routing with IPv6
[ 0.959637] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 0.966526] NET: Registered PF_PACKET protocol family
[ 0.971663] NET: Registered PF_KEY protocol family
[ 0.976464] 8021q: 802.1Q VLAN Support v1.8
[ 0.980675] lib80211: common routines for IEEE802.11 drivers
[ 0.986398] Registering SWP/SWPB emulation handler
[ 0.999840] Freeing unused kernel image (initmem) memory: 8192K
[ 1.006133] Run /init as init process
--
Bert Vermeulen
bert@biot.com
WARNING: multiple messages have this Message-ID (diff)
From: Bert Vermeulen <bert@biot.com>
To: Marc Zyngier <maz@kernel.org>, Linus Walleij <linus.walleij@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
linux-kernel <linux-kernel@vger.kernel.org>,
Linux ARM <linux-arm-kernel@lists.infradead.org>,
Arnd Bergmann <arnd@arndb.de>, Olof Johansson <olof@lixom.net>,
SoC Team <soc@kernel.org>, Rob Herring <robh+dt@kernel.org>,
John Crispin <john@phrozen.org>, Felix Fietkau <nbd@nbd.name>
Subject: Re: [PATCH 3/5] ARM: dts: Add basic support for EcoNet EN7523
Date: Sun, 1 Aug 2021 11:07:48 +0200 [thread overview]
Message-ID: <0fe113c6-4160-fd3c-488d-53d40b6043ee@biot.com> (raw)
Message-ID: <20210801090748.zzNrx5_2z5gvaAbVM13vP-hLkmkxa4cfrdcS6IeVekw@z> (raw)
In-Reply-To: <87y29n26po.wl-maz@kernel.org>
On 7/30/21 4:53 PM, Marc Zyngier wrote:
> On Fri, 30 Jul 2021 15:31:36 +0100,
> Linus Walleij <linus.walleij@linaro.org> wrote:
>>
>> Paging Marc Z and Catalin just so they can see this:
>>
>> On Fri, Jul 30, 2021 at 3:49 PM Bert Vermeulen <bert@biot.com> wrote:
>>
>> > From: John Crispin <john@phrozen.org>
>> >
>> > Add basic support for EcoNet EN7523, enough for booting to console.
>> >
>> > The UART is basically 8250-compatible, except for the clock selection.
>> > A clock-frequency value is synthesized to get this to run at 115200 bps.
>> >
>> > Signed-off-by: John Crispin <john@phrozen.org>
>> > Signed-off-by: Bert Vermeulen <bert@biot.com>
>> (...)
>> > + gic: interrupt-controller@09000000 {
>> > + compatible = "arm,gic-v3";
>> > + interrupt-controller;
>> > + #interrupt-cells = <3>;
>> > + #address-cells = <1>;
>> > + #size-cells = <1>;
>> > + reg = <0x09000000 0x20000>,
>> > + <0x09080000 0x80000>;
>> > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
>> > +
>> > + its: gic-its@09020000 {
>> > + compatible = "arm,gic-v3-its";
>> > + msi-controller;
>> > + #msi-cell = <1>;
>> > + reg = <0x090200000 0x20000>;
>> > + };
>> > + };
>>
>> Yup GICv3 on ARM32-only silicon.
>
> Hey, why not. But that's very unlikely, as Cortex-A7 doesn't have a
> GICv3 CPU interface built in (it only has the memory mapped version),
> and A53/57 were the first CPUs to ever support GICv3. I don't believe
> the description of the CPU in the DT is accurate.
>
> Bert, please send a kernel boot log.
At the bottom of this mail.
>> > + timer {
>> > + compatible = "arm,armv8-timer";
>> > + interrupt-parent = <&gic>;
>> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
>
> Copy paste bug. These are not valid intspecs for GICv3.
FWIW all these were taken verbatim from the vendor's SDK. Not that this
makes them necessarily correct :)
>> > + clock-frequency = <25000000>;
>> > + };
>>
>> Also arm,armv8-timer on ARM32-only silicon.
>
> Probably because that's not what it actually is. My bet is on A53 with
> a crippled firmware.
kernel boot log:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.14.0-rc3-00042-g3af70c6f8e95-dirty
(bert@sumner) (arm-linux-gnueabi-gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0,
GNU ld (GNU Binutils for Ubuntu) 2.34) #392 SMP Sun Aug 1 10:28:13 CEST 2021
[ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] OF: fdt: Machine model: econet,en7523
[ 0.000000] earlycon: uart8250 at MMIO32 0x1fbf0000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x0000000083ffffff]
[ 0.000000] node 0: [mem 0x0000000084000000-0x00000000849fffff]
[ 0.000000] node 0: [mem 0x0000000084a00000-0x0000000084afffff]
[ 0.000000] node 0: [mem 0x0000000084b00000-0x0000000084bfffff]
[ 0.000000] node 0: [mem 0x0000000084c00000-0x0000000084ffffff]
[ 0.000000] node 0: [mem 0x0000000085000000-0x00000000869fffff]
[ 0.000000] node 0: [mem 0x0000000086a00000-0x0000000086afffff]
[ 0.000000] node 0: [mem 0x0000000086b00000-0x0000000086bfffff]
[ 0.000000] node 0: [mem 0x0000000086c00000-0x0000000086cfffff]
[ 0.000000] node 0: [mem 0x0000000086d00000-0x0000000086dfffff]
[ 0.000000] node 0: [mem 0x0000000086e00000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30604 r8192 d22644 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0x1fbf0000
console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 461316K/524288K available (7168K kernel code, 312K
rwdata, 1488K rodata, 8192K init, 142K bss, 62972K reserved, 0K
cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10
jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GICv3: 256 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x09080000
[ 0.000000] random: get_random_bytes called from start_kernel+0x484/0x628
with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff
max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every
4398046511100ns
[ 0.008791] Switching to timer-based delay loop, resolution 40ns
[ 0.015454] Calibrating delay loop (skipped), value calculated using
timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.026833] pid_max: default: 32768 minimum: 301
[ 0.032013] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes,
linear)
[ 0.040047] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes, linear)
[ 0.049172] CPU: Testing write buffer coherency: ok
[ 0.054780] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.061362] Setting up static identity map for 0x80100000 - 0x80100060
[ 0.068667] rcu: Hierarchical SRCU implementation.
[ 0.074290] gic-its@09020000: unable to locate ITS domain
[ 0.080461] smp: Bringing up secondary CPUs ...
[ 0.085769] smp: Brought up 1 node, 1 CPU
[ 0.090179] SMP: Total of 1 processors activated (50.00 BogoMIPS).
[ 0.097013] CPU: All CPU(s) started in SVC mode.
[ 0.103634] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.114499] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.122380] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.129153] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.137265] thermal_sys: Registered thermal governor 'step_wise'
[ 0.137333] No ATAGs?
[ 0.153205] iommu: Default domain type: Translated
[ 0.158713] usbcore: registered new interface driver usbfs
[ 0.164769] usbcore: registered new interface driver hub
[ 0.170660] usbcore: registered new device driver usb
[ 0.176704] NET: Registered PF_ATMPVC protocol family
[ 0.182296] NET: Registered PF_ATMSVC protocol family
[ 0.188055] clocksource: Switched to clocksource arch_sys_counter
[ 0.195462] NET: Registered PF_INET protocol family
[ 0.200971] IP idents hash table entries: 8192 (order: 4, 65536 bytes,
linear)
[ 0.209452] tcp_listen_portaddr_hash hash table entries: 512 (order: 0,
6144 bytes, linear)
[ 0.218713] TCP established hash table entries: 4096 (order: 2, 16384
bytes, linear)
[ 0.227251] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.235158] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.242212] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.249416] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.257205] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.263464] PCI: CLS 0 bytes, default 64
[ 0.348846] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.360684] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.367197] ntfs: driver 2.1.32 [Flags: R/W DEBUG].
[ 0.372785] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.598557] io scheduler mq-deadline registered
[ 0.603555] io scheduler kyber registered
[ 0.619475] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.626838] printk: console [ttyS0] disabled
[ 0.631671] 1fbf0000.serial: ttyS0 at MMIO 0x1fbf0000 (irq = 28,
base_baud = 115200) is a 8250
[ 0.641169] printk: console [ttyS0] enabled
[ 0.641169] printk: console [ttyS0] enabled
[ 0.649943] printk: bootconsole [uart8250] disabled
[ 0.649943] printk: bootconsole [uart8250] disabled
[ 0.706413] brd: module loaded
[ 0.709758] PPP generic driver version 2.4.2
[ 0.714097] PPP BSD Compression module registered
[ 0.718832] PPP Deflate Compression module registered
[ 0.723877] NET: Registered PF_PPPOX protocol family
[ 0.728989] usbcore: registered new interface driver cdc_acm
[ 0.734648] cdc_acm: USB Abstract Control Model driver for USB modems and
ISDN adapters
[ 0.742712] usbcore: registered new interface driver usbserial_generic
[ 0.749278] usbserial: USB Serial support registered for generic
[ 0.755299] usbcore: registered new interface driver cypress_m8
[ 0.761234] usbserial: USB Serial support registered for DeLorme
Earthmate USB
[ 0.768476] usbserial: USB Serial support registered for HID->COM RS232
Adapter
[ 0.775790] usbserial: USB Serial support registered for Nokia CA-42 V2
Adapter
[ 0.783121] usbcore: registered new interface driver ftdi_sio
[ 0.788889] usbserial: USB Serial support registered for FTDI USB Serial
Device
[ 0.796272] hid: raw HID events driver (C) Jiri Kosina
[ 0.801492] usbcore: registered new interface driver usbhid
[ 0.807061] usbhid: USB HID core driver
[ 0.811617] IPv4 over IPsec tunneling driver
[ 0.816458] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[ 0.822866] Initializing XFRM netlink socket
[ 0.827522] NET: Registered PF_INET6 protocol family
[ 0.955712] Segment Routing with IPv6
[ 0.959637] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 0.966526] NET: Registered PF_PACKET protocol family
[ 0.971663] NET: Registered PF_KEY protocol family
[ 0.976464] 8021q: 802.1Q VLAN Support v1.8
[ 0.980675] lib80211: common routines for IEEE802.11 drivers
[ 0.986398] Registering SWP/SWPB emulation handler
[ 0.999840] Freeing unused kernel image (initmem) memory: 8192K
[ 1.006133] Run /init as init process
--
Bert Vermeulen
bert@biot.com
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-08-01 9:07 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20210730134552.853350-1-bert@biot.com>
2021-07-30 13:45 ` [PATCH 3/5] ARM: dts: Add basic support for EcoNet EN7523 Bert Vermeulen
2021-07-30 13:45 ` Bert Vermeulen
2021-07-30 14:31 ` Linus Walleij
2021-07-30 14:31 ` Linus Walleij
2021-07-30 14:31 ` Linus Walleij
2021-07-30 14:53 ` Marc Zyngier
2021-07-30 14:53 ` Marc Zyngier
2021-08-01 9:07 ` Bert Vermeulen [this message]
2021-08-01 9:07 ` Bert Vermeulen
2021-08-01 9:07 ` Bert Vermeulen
2021-08-01 9:40 ` Arnd Bergmann
2021-08-01 9:40 ` Arnd Bergmann
2021-08-01 9:40 ` Arnd Bergmann
2021-08-01 9:50 ` Marc Zyngier
2021-08-01 9:50 ` Marc Zyngier
2021-07-30 14:45 ` Daniel Palmer
2021-07-30 14:45 ` Daniel Palmer
2021-07-30 14:45 ` Daniel Palmer
2021-07-30 14:46 ` Mark Rutland
2021-07-30 14:46 ` Mark Rutland
2021-08-04 16:41 ` Bert Vermeulen
2021-08-04 16:41 ` Bert Vermeulen
2021-08-06 20:59 ` Rob Herring
2021-08-06 20:59 ` Rob Herring
2021-07-30 14:59 ` Mark Rutland
2021-07-30 14:59 ` Mark Rutland
2021-08-06 20:52 ` Rob Herring
2021-08-06 20:52 ` Rob Herring
2021-07-30 16:47 ` Andre Przywara
2021-07-30 16:47 ` Andre Przywara
2021-07-30 17:23 ` Marc Zyngier
2021-07-30 17:23 ` Marc Zyngier
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=0fe113c6-4160-fd3c-488d-53d40b6043ee@biot.com \
--to=bert@biot.com \
--cc=arnd@arndb.de \
--cc=catalin.marinas@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=john@phrozen.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=maz@kernel.org \
--cc=nbd@nbd.name \
--cc=olof@lixom.net \
--cc=robh+dt@kernel.org \
--cc=soc@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).