soc.lore.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Linus Walleij <linus.walleij@linaro.org>
To: Bert Vermeulen <bert@biot.com>, Marc Zyngier <maz@kernel.org>,
	 Catalin Marinas <catalin.marinas@arm.com>
Cc: "open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
	<devicetree@vger.kernel.org>,
	linux-kernel <linux-kernel@vger.kernel.org>,
	 Linux ARM <linux-arm-kernel@lists.infradead.org>,
	Arnd Bergmann <arnd@arndb.de>,  Olof Johansson <olof@lixom.net>,
	SoC Team <soc@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	 John Crispin <john@phrozen.org>, Felix Fietkau <nbd@nbd.name>
Subject: Re: [PATCH 3/5] ARM: dts: Add basic support for EcoNet EN7523
Date: Fri, 30 Jul 2021 16:31:36 +0200	[thread overview]
Message-ID: <CACRpkdYvMtE8b-Xiy6=Aiz20jvY0M0Bz9XmcEQDHhqeS+LErEA@mail.gmail.com> (raw)
In-Reply-To: <20210730134552.853350-4-bert@biot.com>

Paging Marc Z and Catalin just so they can see this:

On Fri, Jul 30, 2021 at 3:49 PM Bert Vermeulen <bert@biot.com> wrote:

> From: John Crispin <john@phrozen.org>
>
> Add basic support for EcoNet EN7523, enough for booting to console.
>
> The UART is basically 8250-compatible, except for the clock selection.
> A clock-frequency value is synthesized to get this to run at 115200 bps.
>
> Signed-off-by: John Crispin <john@phrozen.org>
> Signed-off-by: Bert Vermeulen <bert@biot.com>
(...)
> +       gic: interrupt-controller@09000000 {
> +               compatible = "arm,gic-v3";
> +               interrupt-controller;
> +               #interrupt-cells = <3>;
> +               #address-cells = <1>;
> +               #size-cells = <1>;
> +               reg = <0x09000000 0x20000>,
> +                         <0x09080000 0x80000>;
> +               interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
> +
> +               its: gic-its@09020000 {
> +                       compatible = "arm,gic-v3-its";
> +                       msi-controller;
> +                       #msi-cell = <1>;
> +                       reg = <0x090200000 0x20000>;
> +               };
> +       };

Yup GICv3 on ARM32-only silicon.

> +       timer {
> +               compatible = "arm,armv8-timer";
> +               interrupt-parent = <&gic>;
> +               interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +                            <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +                            <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +                            <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> +               clock-frequency = <25000000>;
> +       };

Also arm,armv8-timer on ARM32-only silicon.

This is kind of a first.

Yours,
Linus Walleij

WARNING: multiple messages have this Message-ID (diff)
From: Linus Walleij <linus.walleij@linaro.org>
To: Bert Vermeulen <bert@biot.com>, Marc Zyngier <maz@kernel.org>,
	 Catalin Marinas <catalin.marinas@arm.com>
Cc: "open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
	<devicetree@vger.kernel.org>,
	linux-kernel <linux-kernel@vger.kernel.org>,
	 Linux ARM <linux-arm-kernel@lists.infradead.org>,
	Arnd Bergmann <arnd@arndb.de>, Olof Johansson <olof@lixom.net>,
	SoC Team <soc@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	 John Crispin <john@phrozen.org>, Felix Fietkau <nbd@nbd.name>
Subject: Re: [PATCH 3/5] ARM: dts: Add basic support for EcoNet EN7523
Date: Fri, 30 Jul 2021 16:31:36 +0200	[thread overview]
Message-ID: <CACRpkdYvMtE8b-Xiy6=Aiz20jvY0M0Bz9XmcEQDHhqeS+LErEA@mail.gmail.com> (raw)
Message-ID: <20210730143136.7BPuWHxgMf6TWugwjzXquXnLE1ulAjiYI9aguH0nA8w@z> (raw)
In-Reply-To: <20210730134552.853350-4-bert@biot.com>

Paging Marc Z and Catalin just so they can see this:

On Fri, Jul 30, 2021 at 3:49 PM Bert Vermeulen <bert@biot.com> wrote:

> From: John Crispin <john@phrozen.org>
>
> Add basic support for EcoNet EN7523, enough for booting to console.
>
> The UART is basically 8250-compatible, except for the clock selection.
> A clock-frequency value is synthesized to get this to run at 115200 bps.
>
> Signed-off-by: John Crispin <john@phrozen.org>
> Signed-off-by: Bert Vermeulen <bert@biot.com>
(...)
> +       gic: interrupt-controller@09000000 {
> +               compatible = "arm,gic-v3";
> +               interrupt-controller;
> +               #interrupt-cells = <3>;
> +               #address-cells = <1>;
> +               #size-cells = <1>;
> +               reg = <0x09000000 0x20000>,
> +                         <0x09080000 0x80000>;
> +               interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
> +
> +               its: gic-its@09020000 {
> +                       compatible = "arm,gic-v3-its";
> +                       msi-controller;
> +                       #msi-cell = <1>;
> +                       reg = <0x090200000 0x20000>;
> +               };
> +       };

Yup GICv3 on ARM32-only silicon.

> +       timer {
> +               compatible = "arm,armv8-timer";
> +               interrupt-parent = <&gic>;
> +               interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +                            <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +                            <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +                            <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> +               clock-frequency = <25000000>;
> +       };

Also arm,armv8-timer on ARM32-only silicon.

This is kind of a first.

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2021-07-30 14:31 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <20210730134552.853350-1-bert@biot.com>
2021-07-30 13:45 ` [PATCH 3/5] ARM: dts: Add basic support for EcoNet EN7523 Bert Vermeulen
2021-07-30 13:45   ` Bert Vermeulen
2021-07-30 14:31   ` Linus Walleij [this message]
2021-07-30 14:31     ` Linus Walleij
2021-07-30 14:31     ` Linus Walleij
2021-07-30 14:53     ` Marc Zyngier
2021-07-30 14:53       ` Marc Zyngier
2021-08-01  9:07       ` Bert Vermeulen
2021-08-01  9:07         ` Bert Vermeulen
2021-08-01  9:07         ` Bert Vermeulen
2021-08-01  9:40         ` Arnd Bergmann
2021-08-01  9:40           ` Arnd Bergmann
2021-08-01  9:40           ` Arnd Bergmann
2021-08-01  9:50         ` Marc Zyngier
2021-08-01  9:50           ` Marc Zyngier
2021-07-30 14:45   ` Daniel Palmer
2021-07-30 14:45     ` Daniel Palmer
2021-07-30 14:45     ` Daniel Palmer
2021-07-30 14:46   ` Mark Rutland
2021-07-30 14:46     ` Mark Rutland
2021-08-04 16:41     ` Bert Vermeulen
2021-08-04 16:41       ` Bert Vermeulen
2021-08-06 20:59       ` Rob Herring
2021-08-06 20:59         ` Rob Herring
2021-07-30 14:59   ` Mark Rutland
2021-07-30 14:59     ` Mark Rutland
2021-08-06 20:52     ` Rob Herring
2021-08-06 20:52       ` Rob Herring
2021-07-30 16:47   ` Andre Przywara
2021-07-30 16:47     ` Andre Przywara
2021-07-30 17:23     ` Marc Zyngier
2021-07-30 17:23       ` Marc Zyngier

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to='CACRpkdYvMtE8b-Xiy6=Aiz20jvY0M0Bz9XmcEQDHhqeS+LErEA@mail.gmail.com' \
    --to=linus.walleij@linaro.org \
    --cc=arnd@arndb.de \
    --cc=bert@biot.com \
    --cc=catalin.marinas@arm.com \
    --cc=devicetree@vger.kernel.org \
    --cc=john@phrozen.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=maz@kernel.org \
    --cc=nbd@nbd.name \
    --cc=olof@lixom.net \
    --cc=robh+dt@kernel.org \
    --cc=soc@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).