From: Matthew Hagan <mnhagan88@gmail.com>
To: Arnd Bergmann <arnd@arndb.de>
Cc: Florian Fainelli <f.fainelli@gmail.com>,
Vladimir Oltean <olteanv@gmail.com>,
Rob Herring <robh+dt@kernel.org>, Olof Johansson <olof@lixom.net>,
SoC Team <soc@kernel.org>, Ray Jui <rjui@broadcom.com>,
Scott Branden <sbranden@broadcom.com>,
bcm-kernel-feedback-list <bcm-kernel-feedback-list@broadcom.com>,
Viresh Kumar <viresh.kumar@linaro.org>,
Sam Ravnborg <sam@ravnborg.org>,
Geert Uytterhoeven <geert+renesas@glider.be>,
DTML <devicetree@vger.kernel.org>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Linux ARM <linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH v4 2/4] ARM: dts: NSP: Add DT files for Meraki MX64 series
Date: Fri, 25 Jun 2021 18:26:19 +0100 [thread overview]
Message-ID: <bbf38c31-ed75-69d2-39ed-94f324b1f220@gmail.com> (raw)
In-Reply-To: <CAK8P3a3NAOgBa1j+Zsm6FwSm2ux49rFcnTEYJJsmSF8TggRnYA@mail.gmail.com>
On 25/06/2021 10:59, Arnd Bergmann wrote:
> On Fri, Jun 25, 2021 at 11:52 AM Matthew Hagan <mnhagan88@gmail.com> wrote:
>> MX64 & MX64W Hardware info:
>> - CPU: Broadcom BCM58625 Cortex A9 @ 1200Mhz
>> - RAM: 2 GB (4 x 4Gb SK Hynix H5TC4G83CFR)
>> - Storage: 1 GB (Micron MT29F8G08ABACA)
>> - Networking: BCM58625 internal switch (5x 1GbE ports)
>> - USB: 1x USB2.0
>> - Serial: Internal header
>> - WLAN(MX64W only): 2x Broadcom BCM43520KMLG on the PCI bus
>>
>> This patch adds the Meraki MX64 series-specific bindings. Since some
>> devices make use of the older A0 SoC, changes need to be made to
>> accommodate this case, including removal of coherency options and
>> modification to the secondary-boot-reg.
>>
>> Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
> Removing the dma-coherent flags in the dts file seemed really odd until
> I read the text above. It would seem more logical to me to have a .dtsi file
> that has all the a0 revision specific changes, and include that from the
> dts file.
How about having separate bcm-nsp-ax and bcm-nsp-bx dtsi files with the
appropriate secondary-boot-reg and dma-coherent (or lack of)
properties, which then include bcm-nsp.dtsi. Thus we can also avoid use
of /delete-property/. Would this be preferable?
>
> On the other hand, the /chosen, /aliases and /memory nodes that you have
> in the .dtsi file should probably get moved into the .dts files, as these tend
> to be board specific settings, even if the examples you have are all
> the same.
I did not come across any convention regarding this, though there are
plenty of cases where the /chosen, /aliases and /memory nodes are
defined in a .dtsi file and used by multiple similar boards. Also note
in this case /aliases is defined in bcm-nsp.dtsi, not by me. Would we
not prefer to avoid having 6x duplication?
> Arnd
>
Matthew
WARNING: multiple messages have this Message-ID
From: Matthew Hagan <mnhagan88@gmail.com>
To: Arnd Bergmann <arnd@arndb.de>
Cc: Florian Fainelli <f.fainelli@gmail.com>,
Vladimir Oltean <olteanv@gmail.com>,
Rob Herring <robh+dt@kernel.org>, Olof Johansson <olof@lixom.net>,
SoC Team <soc@kernel.org>, Ray Jui <rjui@broadcom.com>,
Scott Branden <sbranden@broadcom.com>,
bcm-kernel-feedback-list <bcm-kernel-feedback-list@broadcom.com>,
Viresh Kumar <viresh.kumar@linaro.org>,
Sam Ravnborg <sam@ravnborg.org>,
Geert Uytterhoeven <geert+renesas@glider.be>,
DTML <devicetree@vger.kernel.org>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Linux ARM <linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH v4 2/4] ARM: dts: NSP: Add DT files for Meraki MX64 series
Date: Fri, 25 Jun 2021 18:26:19 +0100 [thread overview]
Message-ID: <bbf38c31-ed75-69d2-39ed-94f324b1f220@gmail.com> (raw)
Message-ID: <20210625172619.iHRwCFvNW8NCDYOAy0ngAN6e30rXvXnKAfwORX-8Lcw@z> (raw)
In-Reply-To: <CAK8P3a3NAOgBa1j+Zsm6FwSm2ux49rFcnTEYJJsmSF8TggRnYA@mail.gmail.com>
On 25/06/2021 10:59, Arnd Bergmann wrote:
> On Fri, Jun 25, 2021 at 11:52 AM Matthew Hagan <mnhagan88@gmail.com> wrote:
>> MX64 & MX64W Hardware info:
>> - CPU: Broadcom BCM58625 Cortex A9 @ 1200Mhz
>> - RAM: 2 GB (4 x 4Gb SK Hynix H5TC4G83CFR)
>> - Storage: 1 GB (Micron MT29F8G08ABACA)
>> - Networking: BCM58625 internal switch (5x 1GbE ports)
>> - USB: 1x USB2.0
>> - Serial: Internal header
>> - WLAN(MX64W only): 2x Broadcom BCM43520KMLG on the PCI bus
>>
>> This patch adds the Meraki MX64 series-specific bindings. Since some
>> devices make use of the older A0 SoC, changes need to be made to
>> accommodate this case, including removal of coherency options and
>> modification to the secondary-boot-reg.
>>
>> Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
> Removing the dma-coherent flags in the dts file seemed really odd until
> I read the text above. It would seem more logical to me to have a .dtsi file
> that has all the a0 revision specific changes, and include that from the
> dts file.
How about having separate bcm-nsp-ax and bcm-nsp-bx dtsi files with the
appropriate secondary-boot-reg and dma-coherent (or lack of)
properties, which then include bcm-nsp.dtsi. Thus we can also avoid use
of /delete-property/. Would this be preferable?
>
> On the other hand, the /chosen, /aliases and /memory nodes that you have
> in the .dtsi file should probably get moved into the .dts files, as these tend
> to be board specific settings, even if the examples you have are all
> the same.
I did not come across any convention regarding this, though there are
plenty of cases where the /chosen, /aliases and /memory nodes are
defined in a .dtsi file and used by multiple similar boards. Also note
in this case /aliases is defined in bcm-nsp.dtsi, not by me. Would we
not prefer to avoid having 6x duplication?
> Arnd
>
Matthew
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-06-25 17:26 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-25 9:49 [PATCH v4 0/4] ARM: dts: NSP: add Meraki MX64/MX65 series Matthew Hagan
2021-06-25 9:49 ` Matthew Hagan
2021-06-25 9:49 ` Matthew Hagan
2021-06-25 9:49 ` [PATCH v4 1/4] ARM: dts: NSP: Add common bindings for MX64/MX65 Matthew Hagan
2021-06-25 9:49 ` Matthew Hagan
2021-06-25 9:49 ` Matthew Hagan
2021-06-25 9:49 ` [PATCH v4 2/4] ARM: dts: NSP: Add DT files for Meraki MX64 series Matthew Hagan
2021-06-25 9:49 ` Matthew Hagan
2021-06-25 9:49 ` Matthew Hagan
2021-06-25 9:59 ` Arnd Bergmann
2021-06-25 9:59 ` Arnd Bergmann
2021-06-25 9:59 ` Arnd Bergmann
2021-06-25 17:26 ` Matthew Hagan [this message]
2021-06-25 17:26 ` Matthew Hagan
2021-06-25 17:30 ` Florian Fainelli
2021-06-25 17:30 ` Florian Fainelli
2021-06-25 18:40 ` Arnd Bergmann
2021-06-25 18:40 ` Arnd Bergmann
2021-06-25 18:40 ` Arnd Bergmann
2021-06-25 9:49 ` [PATCH v4 3/4] ARM: dts: NSP: Add DT files for Meraki MX65 series Matthew Hagan
2021-06-25 9:49 ` Matthew Hagan
2021-06-25 9:49 ` Matthew Hagan
2021-06-25 9:49 ` [PATCH v4 4/4] dt-bindings: arm: bcm: NSP: add Meraki MX64/MX65 Matthew Hagan
2021-06-25 9:49 ` Matthew Hagan
2021-06-25 9:49 ` Matthew Hagan
2021-07-02 15:14 ` Rob Herring
2021-07-02 15:14 ` Rob Herring
2021-08-05 8:57 ` [PATCH v4 0/4] ARM: dts: NSP: add Meraki MX64/MX65 series Florian Fainelli
2021-08-05 8:57 ` Florian Fainelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=bbf38c31-ed75-69d2-39ed-94f324b1f220@gmail.com \
--to=mnhagan88@gmail.com \
--cc=arnd@arndb.de \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=geert+renesas@glider.be \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=olof@lixom.net \
--cc=olteanv@gmail.com \
--cc=rjui@broadcom.com \
--cc=robh+dt@kernel.org \
--cc=sam@ravnborg.org \
--cc=sbranden@broadcom.com \
--cc=soc@kernel.org \
--cc=viresh.kumar@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).