From: Florian Fainelli <f.fainelli@gmail.com>
To: stable@vger.kernel.org
Cc: Florian Fainelli <f.fainelli@gmail.com>,
Linus Walleij <linus.walleij@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>, Ray Jui <rjui@broadcom.com>,
Scott Branden <sbranden@broadcom.com>,
bcm-kernel-feedback-list@broadcom.com (maintainer:BROADCOM
BCM281XX/BCM11XXX/BCM216XX ARM ARCHITE...),
Eric Anholt <eric@anholt.net>, Stefan Wahren <wahrenst@gmx.net>,
Nicolas Saenz Julienne <nsaenz@kernel.org>,
Phil Elwell <phil@raspberrypi.com>,
devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND
FLATTENED DEVICE TREE BINDINGS),
linux-kernel@vger.kernel.org (open list),
linux-gpio@vger.kernel.org (open list:PIN CONTROL SUBSYSTEM),
linux-rpi-kernel@lists.infradead.org (moderated list:BROADCOM
BCM2711/BCM2835 ARM ARCHITECTURE),
linux-arm-kernel@lists.infradead.org (moderated list:BROADCOM
BCM2711/BCM2835 ARM ARCHITECTURE)
Subject: [PATCH stable 5.4 5/7] pinctrl: bcm2835: Add support for wake-up interrupts
Date: Tue, 25 Jan 2022 11:42:20 -0800 [thread overview]
Message-ID: <20220125194222.12783-6-f.fainelli@gmail.com> (raw)
In-Reply-To: <20220125194222.12783-1-f.fainelli@gmail.com>
commit 920fecc1aa4591da27ef9dcb338fc5da86b404d7 upstream
Leverage the IRQCHIP_MASK_ON_SUSPEND flag in order to avoid having to
specifically treat the GPIO interrupts during suspend and resume, and
simply implement an irq_set_wake() callback that is responsible for
enabling the parent wake-up interrupt as a wake-up interrupt.
To avoid allocating unnecessary resources for other chips, the wake-up
interrupts are only initialized if we have a brcm,bcm7211-gpio
compatibility string.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200531001101.24945-5-f.fainelli@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/pinctrl/bcm/pinctrl-bcm2835.c | 76 ++++++++++++++++++++++++++-
1 file changed, 75 insertions(+), 1 deletion(-)
diff --git a/drivers/pinctrl/bcm/pinctrl-bcm2835.c b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
index e763c680b9c2..436184ebd2ef 100644
--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
@@ -19,6 +19,7 @@
#include <linux/irq.h>
#include <linux/irqdesc.h>
#include <linux/init.h>
+#include <linux/interrupt.h>
#include <linux/of_address.h>
#include <linux/of.h>
#include <linux/of_irq.h>
@@ -76,6 +77,7 @@
struct bcm2835_pinctrl {
struct device *dev;
void __iomem *base;
+ int *wake_irq;
/* note: locking assumes each bank will have its own unsigned long */
unsigned long enabled_irq_map[BCM2835_NUM_BANKS];
@@ -432,6 +434,11 @@ static void bcm2835_gpio_irq_handler(struct irq_desc *desc)
chained_irq_exit(host_chip, desc);
}
+static irqreturn_t bcm2835_gpio_wake_irq_handler(int irq, void *dev_id)
+{
+ return IRQ_HANDLED;
+}
+
static inline void __bcm2835_gpio_irq_config(struct bcm2835_pinctrl *pc,
unsigned reg, unsigned offset, bool enable)
{
@@ -631,6 +638,34 @@ static void bcm2835_gpio_irq_ack(struct irq_data *data)
bcm2835_gpio_set_bit(pc, GPEDS0, gpio);
}
+static int bcm2835_gpio_irq_set_wake(struct irq_data *data, unsigned int on)
+{
+ struct gpio_chip *chip = irq_data_get_irq_chip_data(data);
+ struct bcm2835_pinctrl *pc = gpiochip_get_data(chip);
+ unsigned gpio = irqd_to_hwirq(data);
+ unsigned int irqgroup;
+ int ret = -EINVAL;
+
+ if (!pc->wake_irq)
+ return ret;
+
+ if (gpio <= 27)
+ irqgroup = 0;
+ else if (gpio >= 28 && gpio <= 45)
+ irqgroup = 1;
+ else if (gpio >= 46 && gpio <= 57)
+ irqgroup = 2;
+ else
+ return ret;
+
+ if (on)
+ ret = enable_irq_wake(pc->wake_irq[irqgroup]);
+ else
+ ret = disable_irq_wake(pc->wake_irq[irqgroup]);
+
+ return ret;
+}
+
static struct irq_chip bcm2835_gpio_irq_chip = {
.name = MODULE_NAME,
.irq_enable = bcm2835_gpio_irq_enable,
@@ -639,6 +674,8 @@ static struct irq_chip bcm2835_gpio_irq_chip = {
.irq_ack = bcm2835_gpio_irq_ack,
.irq_mask = bcm2835_gpio_irq_disable,
.irq_unmask = bcm2835_gpio_irq_enable,
+ .irq_set_wake = bcm2835_gpio_irq_set_wake,
+ .flags = IRQCHIP_MASK_ON_SUSPEND,
};
static int bcm2835_pctl_get_groups_count(struct pinctrl_dev *pctldev)
@@ -1151,6 +1188,7 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev)
struct resource iomem;
int err, i;
const struct of_device_id *match;
+ int is_7211 = 0;
BUILD_BUG_ON(ARRAY_SIZE(bcm2835_gpio_pins) != BCM2711_NUM_GPIOS);
BUILD_BUG_ON(ARRAY_SIZE(bcm2835_gpio_groups) != BCM2711_NUM_GPIOS);
@@ -1177,6 +1215,7 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev)
return -EINVAL;
pdata = match->data;
+ is_7211 = of_device_is_compatible(np, "brcm,bcm7211-gpio");
pc->gpio_chip = *pdata->gpio_chip;
pc->gpio_chip.parent = dev;
@@ -1211,6 +1250,15 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev)
GFP_KERNEL);
if (!girq->parents)
return -ENOMEM;
+
+ if (is_7211) {
+ pc->wake_irq = devm_kcalloc(dev, BCM2835_NUM_IRQS,
+ sizeof(*pc->wake_irq),
+ GFP_KERNEL);
+ if (!pc->wake_irq)
+ return -ENOMEM;
+ }
+
/*
* Use the same handler for all groups: this is necessary
* since we use one gpiochip to cover all lines - the
@@ -1218,8 +1266,34 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev)
* bank that was firing the IRQ and look up the per-group
* and bank data.
*/
- for (i = 0; i < BCM2835_NUM_IRQS; i++)
+ for (i = 0; i < BCM2835_NUM_IRQS; i++) {
+ int len;
+ char *name;
+
girq->parents[i] = irq_of_parse_and_map(np, i);
+ if (!is_7211)
+ continue;
+
+ /* Skip over the all banks interrupts */
+ pc->wake_irq[i] = irq_of_parse_and_map(np, i +
+ BCM2835_NUM_IRQS + 1);
+
+ len = strlen(dev_name(pc->dev)) + 16;
+ name = devm_kzalloc(pc->dev, len, GFP_KERNEL);
+ if (!name)
+ return -ENOMEM;
+
+ snprintf(name, len, "%s:bank%d", dev_name(pc->dev), i);
+
+ /* These are optional interrupts */
+ err = devm_request_irq(dev, pc->wake_irq[i],
+ bcm2835_gpio_wake_irq_handler,
+ IRQF_SHARED, name, pc);
+ if (err)
+ dev_warn(dev, "unable to request wake IRQ %d\n",
+ pc->wake_irq[i]);
+ }
+
girq->default_type = IRQ_TYPE_NONE;
girq->handler = handle_level_irq;
--
2.25.1
next prev parent reply other threads:[~2022-01-25 19:42 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-01-25 19:42 [PATCH stable 5.4 0/7] pinctrl-bcm2835 gpio-ranges bugfix Florian Fainelli
2022-01-25 19:42 ` [PATCH stable 5.4 1/7] pinctrl: bcm2835: Drop unused define Florian Fainelli
2022-01-25 19:42 ` [PATCH stable 5.4 2/7] pinctrl: bcm2835: Refactor platform data Florian Fainelli
2022-01-25 19:42 ` [PATCH stable 5.4 3/7] pinctrl: bcm2835: Add support for all GPIOs on BCM2711 Florian Fainelli
2022-01-25 19:42 ` [PATCH stable 5.4 4/7] pinctrl: bcm2835: Match BCM7211 compatible string Florian Fainelli
2022-01-25 19:42 ` Florian Fainelli [this message]
2022-01-25 19:42 ` [PATCH stable 5.4 6/7] pinctrl: bcm2835: Change init order for gpio hogs Florian Fainelli
2022-01-25 19:42 ` [PATCH stable 5.4 7/7] ARM: dts: gpio-ranges property is now required Florian Fainelli
2022-01-27 15:41 ` [PATCH stable 5.4 0/7] pinctrl-bcm2835 gpio-ranges bugfix Greg KH
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220125194222.12783-6-f.fainelli@gmail.com \
--to=f.fainelli@gmail.com \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=devicetree@vger.kernel.org \
--cc=eric@anholt.net \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rpi-kernel@lists.infradead.org \
--cc=mark.rutland@arm.com \
--cc=nsaenz@kernel.org \
--cc=phil@raspberrypi.com \
--cc=rjui@broadcom.com \
--cc=robh+dt@kernel.org \
--cc=sbranden@broadcom.com \
--cc=stable@vger.kernel.org \
--cc=wahrenst@gmx.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).