From: Yifan Gu <me@yifangu.com>
To: u-boot@lists.denx.de
Cc: Yifan Gu <me@yifangu.com>,
Jagan Teki <jagan@amarulasolutions.com>,
Andre Przywara <andre.przywara@arm.com>,
Icenowy Zheng <icenowy@aosc.io>,
George Hilliard <thirtythreeforty@gmail.com>
Subject: [PATCH 17/27] sunxi: spi: Add suniv pin controller support
Date: Sun, 25 Jul 2021 19:16:26 -0400 [thread overview]
Message-ID: <20210725231636.879913-18-me@yifangu.com> (raw)
In-Reply-To: <20210725231636.879913-1-me@yifangu.com>
From: George Hilliard <thirtythreeforty@gmail.com>
suniv needs slightly different register settings to enable the SPI
peripheral. The magic numbers are already provided by the architecture
support; we just have to check for them here.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Yifan Gu <me@yifangu.com>
---
drivers/spi/spi-sunxi.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/spi/spi-sunxi.c b/drivers/spi/spi-sunxi.c
index aa392502b7..320bd61d13 100644
--- a/drivers/spi/spi-sunxi.c
+++ b/drivers/spi/spi-sunxi.c
@@ -255,6 +255,8 @@ static int sun4i_spi_parse_pins(struct udevice *dev)
if (IS_ENABLED(CONFIG_MACH_SUN50I))
sunxi_gpio_set_cfgpin(pin, SUN50I_GPC_SPI0);
+ else if (IS_ENABLED(CONFIG_MACH_SUNIV))
+ sunxi_gpio_set_cfgpin(pin, SUNIV_GPC_SPI0);
else
sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_SPI0);
sunxi_gpio_set_drv(pin, drive);
--
2.25.1
next prev parent reply other threads:[~2021-07-25 23:36 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-07-25 23:16 [PATCH 00/27] Add F1C100s based PocketGo handheld support Yifan Gu
2021-07-25 23:16 ` [PATCH 01/27] arm: arm926ejs: start.S: port save_boot_params support from armv7 code Yifan Gu
2021-07-25 23:16 ` [PATCH 02/27] arm: arm926ej-s: add sunxi code Yifan Gu
2021-07-25 23:16 ` [PATCH 03/27] sunxi: add support for suniv architecture Yifan Gu
2021-07-25 23:16 ` [PATCH 04/27] sunxi: suniv: add support for Lichee Pi Nano Yifan Gu
2021-07-25 23:16 ` [PATCH 05/27] sunxi: suniv: add boot sequence for SPL to try Yifan Gu
2021-07-25 23:16 ` [PATCH 06/27] sunxi: spi-spl: add support for SUNIV Yifan Gu
2021-07-25 23:16 ` [PATCH 07/27] sunxi: add SPI0 node for suniv Yifan Gu
2021-07-25 23:16 ` [PATCH 08/27] sunxi: enable SPI NOR on Lichee Pi Nano Yifan Gu
2021-07-25 23:16 ` [PATCH 09/27] sunxi: add defconfig for Lichee Pi Nano with SPI Flash support Yifan Gu
2021-07-25 23:16 ` [PATCH 10/27] sunxi: add support for UART at PF for suniv Yifan Gu
2021-07-25 23:16 ` [PATCH 11/27] sunxi: do not set PF MMC0 pinmux when PF uart is used Yifan Gu
2021-07-25 23:16 ` [PATCH 12/27] sunxi: allow to enable MMC driver when using PF UART0 Yifan Gu
2021-07-25 23:16 ` [PATCH 13/27] sunxi: Don't provide enable_cache() on suniv Yifan Gu
2021-07-25 23:16 ` [PATCH 14/27] sunxi: implement clock driver for suniv f1c100s Yifan Gu
2022-01-20 0:38 ` Sean Anderson
2021-07-25 23:16 ` [PATCH 15/27] sunxi: gpio: Add support for suniv-f1c100s Yifan Gu
2021-07-25 23:16 ` [PATCH 16/27] sunxi: spi: restore bus speed and mode after reset Yifan Gu
2021-07-25 23:16 ` Yifan Gu [this message]
2021-07-25 23:16 ` [PATCH 18/27] sunxi: suniv: add device tree nodes for f1c100s MMC controllers Yifan Gu
2021-07-25 23:16 ` [PATCH 19/27] arm: dts: sunxi: do not renumber if mmc2 does not exist Yifan Gu
2021-07-26 1:01 ` Icenowy Zheng
2021-07-25 23:16 ` [PATCH 20/27] board: licheepi_nano: set CONFIG_MMC_SUNXI_SLOT_EXTRA Yifan Gu
2021-07-25 23:16 ` [PATCH 21/27] sunxi: suniv: add missing header include for udelay Yifan Gu
2021-07-25 23:16 ` [PATCH 22/27] sunxi: suniv: allow serial connection on uart1 Yifan Gu
2021-07-25 23:16 ` [PATCH 23/27] sunxi: suniv: do not detect boot sector on suniv Yifan Gu
2021-07-25 23:16 ` [PATCH 24/27] sunxi: suniv: set SYS_TEXT_BASE default Yifan Gu
2021-07-25 23:16 ` [PATCH 25/27] sunxi: suniv: disable mmc optimization for suniv Yifan Gu
2021-07-25 23:16 ` [PATCH 26/27] arm: dts: suniv: define uart1 pins Yifan Gu
2021-07-25 23:16 ` [PATCH 27/27] arm: dts: add pocketgo handheld support Yifan Gu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210725231636.879913-18-me@yifangu.com \
--to=me@yifangu.com \
--cc=andre.przywara@arm.com \
--cc=icenowy@aosc.io \
--cc=jagan@amarulasolutions.com \
--cc=thirtythreeforty@gmail.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).