[PATCH 1/2] rockchip: rk3328: Add support for Orange Pi R1 Plus

[Tianling Shen <cnsztl@gmail.com>]

Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.

This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.

The device tree and description are taken from kernel v6.3-rc1:
https://github.com/torvalds/linux/commit/51712e1d014aaaa4c6e1e7e84932d58b5c0f59ed

Signed-off-by: Tianling Shen <cnsztl@gmail.com>
---

Please note this patch is based on my previous one:
https://lore.kernel.org/u-boot/20230411101449.17123-1-cnsztl@gmail.com/

---
 arch/arm/dts/Makefile                         |   1 +
 .../dts/rk3328-orangepi-r1-plus-u-boot.dtsi   |  46 +++
 arch/arm/dts/rk3328-orangepi-r1-plus.dts      | 373 ++++++++++++++++++
 board/rockchip/evb_rk3328/MAINTAINERS         |   6 +
 configs/orangepi-r1-plus-rk3328_defconfig     | 114 ++++++
 5 files changed, 540 insertions(+)
 create mode 100644 arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3328-orangepi-r1-plus.dts
 create mode 100644 configs/orangepi-r1-plus-rk3328_defconfig

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 0d9b832467..73633d6bf4 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -125,6 +125,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3328) += \
 	rk3328-evb.dtb \
 	rk3328-nanopi-r2c.dtb \
 	rk3328-nanopi-r2s.dtb \
+	rk3328-orangepi-r1-plus.dtb \
 	rk3328-roc-cc.dtb \
 	rk3328-rock64.dtb \
 	rk3328-rock-pi-e.dtb
diff --git a/arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi b/arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi
new file mode 100644
index 0000000000..637c70adf1
--- /dev/null
+++ b/arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * (C) Copyright 2018-2019 Rockchip Electronics Co., Ltd
+ * (C) Copyright 2020 David Bauer
+ */
+
+#include "rk3328-u-boot.dtsi"
+#include "rk3328-sdram-ddr4-666.dtsi"
+/ {
+	chosen {
+		u-boot,spl-boot-order = "same-as-spl", &sdmmc, &emmc;
+	};
+};
+
+&gpio0 {
+	bootph-pre-ram;
+};
+
+&pinctrl {
+	bootph-pre-ram;
+};
+
+&sdmmc0m1_pin {
+	bootph-pre-ram;
+};
+
+&pcfg_pull_up_4ma {
+	bootph-pre-ram;
+};
+
+/* Need this and all the pinctrl/gpio stuff above to set pinmux */
+&vcc_sd {
+	bootph-pre-ram;
+};
+
+&gmac2io {
+	snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+};
+
+&spi0 {
+	spi_flash: spiflash@0 {
+		bootph-all;
+	};
+};
diff --git a/arch/arm/dts/rk3328-orangepi-r1-plus.dts b/arch/arm/dts/rk3328-orangepi-r1-plus.dts
new file mode 100644
index 0000000000..dc83d74045
--- /dev/null
+++ b/arch/arm/dts/rk3328-orangepi-r1-plus.dts
@@ -0,0 +1,373 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Based on rk3328-nanopi-r2s.dts, which is:
+ *   Copyright (c) 2020 David Bauer <mail@david-bauer.net>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "rk3328.dtsi"
+
+/ {
+	model = "Xunlong Orange Pi R1 Plus";
+	compatible = "xunlong,orangepi-r1-plus", "rockchip,rk3328";
+
+	aliases {
+		ethernet1 = &rtl8153;
+		mmc0 = &sdmmc;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac_clk: gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac_clkin";
+		#clock-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
+		pinctrl-names = "default";
+
+		led-0 {
+			function = LED_FUNCTION_LAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
+		pinctrl-0 = <&sdmmc0m1_pin>;
+		pinctrl-names = "default";
+		regulator-name = "vcc_sd";
+		regulator-boot-on;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_sys: vcc-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vdd_5v_lan: vdd-5v-lan-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&lan_vdd_pin>;
+		pinctrl-names = "default";
+		regulator-name = "vdd_5v_lan";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&display_subsystem {
+	status = "disabled";
+};
+
+&gmac2io {
+	assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+	assigned-clock-parents = <&gmac_clk>, <&gmac_clk>;
+	clock_in_out = "input";
+	phy-handle = <&rtl8211e>;
+	phy-mode = "rgmii";
+	phy-supply = <&vcc_io>;
+	pinctrl-0 = <&rgmiim1_pins>;
+	pinctrl-names = "default";
+	snps,aal;
+	rx_delay = <0x18>;
+	tx_delay = <0x24>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtl8211e: ethernet-phy@1 {
+			reg = <1>;
+			pinctrl-0 = <&eth_phy_reset_pin>;
+			pinctrl-names = "default";
+			reset-assert-us = <10000>;
+			reset-deassert-us = <50000>;
+			reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	rk805: pmic@18 {
+		compatible = "rockchip,rk805";
+		reg = <0x18>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk805-clkout2";
+		gpio-controller;
+		#gpio-cells = <2>;
+		pinctrl-0 = <&pmic_int_l>;
+		pinctrl-names = "default";
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_io>;
+		vcc6-supply = <&vcc_sys>;
+
+		regulators {
+			vdd_log: DCDC_REG1 {
+				regulator-name = "vdd_log";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <712500>;
+				regulator-max-microvolt = <1450000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vdd_arm: DCDC_REG2 {
+				regulator-name = "vdd_arm";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <712500>;
+				regulator-max-microvolt = <1450000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <950000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-name = "vcc_io";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_18: LDO_REG1 {
+				regulator-name = "vcc_18";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_emmc: LDO_REG2 {
+				regulator-name = "vcc18_emmc";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-name = "vdd_10";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+		};
+	};
+};
+
+&io_domains {
+	pmuio-supply = <&vcc_io>;
+	vccio1-supply = <&vcc_io>;
+	vccio2-supply = <&vcc18_emmc>;
+	vccio3-supply = <&vcc_io>;
+	vccio4-supply = <&vcc_io>;
+	vccio5-supply = <&vcc_io>;
+	vccio6-supply = <&vcc_io>;
+	status = "okay";
+};
+
+&pinctrl {
+	gmac2io {
+		eth_phy_reset_pin: eth-phy-reset-pin {
+			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	leds {
+		lan_led_pin: lan-led-pin {
+			rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		sys_led_pin: sys-led-pin {
+			rockchip,pins = <3 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		wan_led_pin: wan-led-pin {
+			rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	lan {
+		lan_vdd_pin: lan-vdd-pin {
+			rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	disable-wp;
+	pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
+	pinctrl-names = "default";
+	vmmc-supply = <&vcc_sd>;
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&u2phy {
+	status = "okay";
+};
+
+&u2phy_host {
+	status = "okay";
+};
+
+&u2phy_otg {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb20_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbdrd3 {
+	dr_mode = "host";
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* Second port is for USB 3.0 */
+	rtl8153: device@2 {
+		compatible = "usbbda,8153";
+		reg = <2>;
+	};
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
diff --git a/board/rockchip/evb_rk3328/MAINTAINERS b/board/rockchip/evb_rk3328/MAINTAINERS
index 3c46613ab5..91dc6b58cf 100644
--- a/board/rockchip/evb_rk3328/MAINTAINERS
+++ b/board/rockchip/evb_rk3328/MAINTAINERS
@@ -18,6 +18,12 @@ F:      configs/nanopi-r2s-rk3328_defconfig
 F:      arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi
 F:      arch/arm/dts/rk3328-nanopi-r2s.dts
 
+ORANGEPI-R1-PLUS-RK3328
+M:      Tianling Shen <cnsztl@gmail.com>
+S:      Maintained
+F:      configs/orangepi-r1-plus-rk3328_defconfig
+F:      arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi
+
 ROC-RK3328-CC
 M:      Loic Devulder <ldevulder@suse.com>
 M:      Chen-Yu Tsai <wens@csie.org>
diff --git a/configs/orangepi-r1-plus-rk3328_defconfig b/configs/orangepi-r1-plus-rk3328_defconfig
new file mode 100644
index 0000000000..3f62f0588d
--- /dev/null
+++ b/configs/orangepi-r1-plus-rk3328_defconfig
@@ -0,0 +1,114 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00200000
+CONFIG_SPL_GPIO=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
+CONFIG_ENV_OFFSET=0x3F8000
+CONFIG_DEFAULT_DEVICE_TREE="rk3328-orangepi-r1-plus"
+CONFIG_DM_RESET=y
+CONFIG_ROCKCHIP_RK3328=y
+CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_TPL_LIBCOMMON_SUPPORT=y
+CONFIG_TPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_DRIVERS_MISC=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_SPL_STACK=0x400000
+CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
+CONFIG_DEBUG_UART_BASE=0xFF130000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SYS_LOAD_ADDR=0x800800
+CONFIG_DEBUG_UART=y
+# CONFIG_ANDROID_BOOT_IMAGE is not set
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_MISC_INIT_R=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x2000000
+CONFIG_SPL_BSS_MAX_SIZE=0x2000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_I2C=y
+CONFIG_SPL_POWER=y
+CONFIG_SPL_ATF=y
+CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
+CONFIG_TPL_SYS_MALLOC_SIMPLE=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TIME=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_TPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_TPL_OF_PLATDATA=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_TPL_DM=y
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_TPL_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SPL_SYSCON=y
+CONFIG_TPL_SYSCON=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_FASTBOOT_BUF_ADDR=0x800800
+CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_SF_DEFAULT_SPEED=20000000
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_SPL_PMIC_RK8XX=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_REGULATOR_PWM=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_SPL_DM_REGULATOR_FIXED=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_RAM=y
+CONFIG_SPL_RAM=y
+CONFIG_TPL_RAM=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_ROCKCHIP_SPI=y
+CONFIG_SYSINFO=y
+CONFIG_SYSRESET=y
+# CONFIG_TPL_SYSRESET is not set
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_SPL_TINY_MEMSET=y
+CONFIG_TPL_TINY_MEMSET=y
+CONFIG_ERRNO_STR=y
-- 
2.40.0