From: Anup Patel <anup.patel@broadcom.com>
To: Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>,
Will Deacon <will.deacon@arm.com>, Ray Jui <rjui@broadcom.com>,
Scott Branden <sbranden@broadcom.com>,
Jon Mason <jonmason@broadcom.com>,
Florian Fainelli <f.fainelli@gmail.com>,
Oza Pawandeep <oza.oza@broadcom.com>,
Srinath Mannam <srinath.mannam@broadcom.com>,
Pramod Kumar <pramod.kumar@broadcom.com>,
Sandeep Tripathy <sandeep.tripathy@broadcom.com>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-clk@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
bcm-kernel-feedback-list@broadcom.com,
Pramod Kumar <pramodku@broadcom.com>
Subject: [PATCH v6 08/11] arm64: dts: Add GPIO DT nodes for Stingray SOC
Date: Fri, 2 Jun 2017 12:04:32 +0530 [thread overview]
Message-ID: <1496385275-6899-9-git-send-email-anup.patel@broadcom.com> (raw)
In-Reply-To: <1496385275-6899-1-git-send-email-anup.patel@broadcom.com>
From: Pramod Kumar <pramod.kumar@broadcom.com>
The GPIOs on Stingray SOC are based on iProc GPIOs hence
using this we add GPIO DT nodes for Stingray SOC.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
.../arm64/boot/dts/broadcom/stingray/stingray.dtsi | 34 ++++++++++++++++++++++
1 file changed, 34 insertions(+)
diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
index 639c25d..e91debe 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
@@ -251,6 +251,14 @@
ranges = <0x0 0x0 0x66400000 0x100000>;
#include "stingray-clock.dtsi"
+
+ gpio_crmu: gpio@00024800 {
+ compatible = "brcm,iproc-gpio";
+ reg = <0x00024800 0x4c>;
+ ngpios = <6>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
};
hsls {
@@ -261,6 +269,32 @@
#include "stingray-pinctrl.dtsi"
+ gpio_hsls: gpio@000d0000 {
+ compatible = "brcm,iproc-gpio";
+ reg = <0x000d0000 0x864>;
+ ngpios = <151>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-ranges = <&pinmux 0 0 16>,
+ <&pinmux 16 71 2>,
+ <&pinmux 18 131 8>,
+ <&pinmux 26 83 6>,
+ <&pinmux 32 123 4>,
+ <&pinmux 36 43 24>,
+ <&pinmux 60 89 2>,
+ <&pinmux 62 73 4>,
+ <&pinmux 66 95 28>,
+ <&pinmux 94 127 4>,
+ <&pinmux 98 139 10>,
+ <&pinmux 108 16 27>,
+ <&pinmux 135 77 6>,
+ <&pinmux 141 67 4>,
+ <&pinmux 145 149 6>,
+ <&pinmux 151 91 4>;
+ };
+
uart0: uart@00100000 {
device_type = "serial";
compatible = "snps,dw-apb-uart";
--
2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: anup.patel@broadcom.com (Anup Patel)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v6 08/11] arm64: dts: Add GPIO DT nodes for Stingray SOC
Date: Fri, 2 Jun 2017 12:04:32 +0530 [thread overview]
Message-ID: <1496385275-6899-9-git-send-email-anup.patel@broadcom.com> (raw)
In-Reply-To: <1496385275-6899-1-git-send-email-anup.patel@broadcom.com>
From: Pramod Kumar <pramod.kumar@broadcom.com>
The GPIOs on Stingray SOC are based on iProc GPIOs hence
using this we add GPIO DT nodes for Stingray SOC.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
.../arm64/boot/dts/broadcom/stingray/stingray.dtsi | 34 ++++++++++++++++++++++
1 file changed, 34 insertions(+)
diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
index 639c25d..e91debe 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
@@ -251,6 +251,14 @@
ranges = <0x0 0x0 0x66400000 0x100000>;
#include "stingray-clock.dtsi"
+
+ gpio_crmu: gpio at 00024800 {
+ compatible = "brcm,iproc-gpio";
+ reg = <0x00024800 0x4c>;
+ ngpios = <6>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
};
hsls {
@@ -261,6 +269,32 @@
#include "stingray-pinctrl.dtsi"
+ gpio_hsls: gpio at 000d0000 {
+ compatible = "brcm,iproc-gpio";
+ reg = <0x000d0000 0x864>;
+ ngpios = <151>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-ranges = <&pinmux 0 0 16>,
+ <&pinmux 16 71 2>,
+ <&pinmux 18 131 8>,
+ <&pinmux 26 83 6>,
+ <&pinmux 32 123 4>,
+ <&pinmux 36 43 24>,
+ <&pinmux 60 89 2>,
+ <&pinmux 62 73 4>,
+ <&pinmux 66 95 28>,
+ <&pinmux 94 127 4>,
+ <&pinmux 98 139 10>,
+ <&pinmux 108 16 27>,
+ <&pinmux 135 77 6>,
+ <&pinmux 141 67 4>,
+ <&pinmux 145 149 6>,
+ <&pinmux 151 91 4>;
+ };
+
uart0: uart at 00100000 {
device_type = "serial";
compatible = "snps,dw-apb-uart";
--
2.7.4
next prev parent reply other threads:[~2017-06-02 6:36 UTC|newest]
Thread overview: 41+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-02 6:34 [PATCH v6 00/11] Broadcom Stingray SOC Initial Support Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 6:34 ` [PATCH v6 01/11] dt-bindings: bcm: Add Broadcom Stingray bindings document Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 6:34 ` [PATCH v6 02/11] dt-bindings: clk: Extend binding doc for Stingray SOC Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 6:34 ` [PATCH v6 03/11] clk: bcm: Add clocks " Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 22:10 ` Stephen Boyd
2017-06-02 22:10 ` Stephen Boyd
2017-06-06 4:21 ` Anup Patel
2017-06-06 4:21 ` Anup Patel
2017-06-02 6:34 ` [PATCH v6 04/11] arm64: dts: Initial DTS files for Broadcom " Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 6:34 ` [PATCH v6 05/11] arm64: dts: Add clock DT nodes for " Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 6:34 ` [PATCH v6 06/11] arm64: dts: Add NAND " Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 6:34 ` [PATCH v6 07/11] arm64: dts: Add pinctrl " Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 6:34 ` Anup Patel [this message]
2017-06-02 6:34 ` [PATCH v6 08/11] arm64: dts: Add GPIO " Anup Patel
2017-06-02 6:34 ` [PATCH v6 09/11] arm64: dts: Add I2C DT nodes for Stingray SoC Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 6:34 ` [PATCH v6 10/11] arm64: dts: Add PL022, PL330 and SP805 DT nodes for Stingray Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-02 6:34 ` [PATCH v6 11/11] arm64: dts: Add PWM and SDHCI DT nodes for Stingray SOC Anup Patel
2017-06-02 6:34 ` Anup Patel
2017-06-05 16:51 ` [PATCH v6 00/11] Broadcom Stingray SOC Initial Support Florian Fainelli
2017-06-05 16:51 ` Florian Fainelli
2017-06-06 2:08 ` Florian Fainelli
2017-06-06 2:08 ` Florian Fainelli
2017-06-06 3:20 ` Anup Patel
2017-06-06 3:20 ` Anup Patel
2017-06-06 22:30 ` Stephen Boyd
2017-06-06 22:30 ` Stephen Boyd
2017-06-06 22:30 ` Stephen Boyd
2017-06-20 0:28 ` Florian Fainelli
2017-06-20 0:28 ` Florian Fainelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1496385275-6899-9-git-send-email-anup.patel@broadcom.com \
--to=anup.patel@broadcom.com \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=catalin.marinas@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=jonmason@broadcom.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mturquette@baylibre.com \
--cc=oza.oza@broadcom.com \
--cc=pramod.kumar@broadcom.com \
--cc=pramodku@broadcom.com \
--cc=rjui@broadcom.com \
--cc=robh+dt@kernel.org \
--cc=sandeep.tripathy@broadcom.com \
--cc=sboyd@codeaurora.org \
--cc=sbranden@broadcom.com \
--cc=srinath.mannam@broadcom.com \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.