All of lore.kernel.org
 help / color / mirror / Atom feed
From: satya priya <skakit@codeaurora.org>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Matthias Kaehlcke <mka@chromium.org>,
	gregkh@linuxfoundation.org, Andy Gross <agross@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, akashast@codeaurora.org,
	rojay@codeaurora.org, msavaliy@qti.qualcomm.com,
	dianders@chromium.org, satya priya <skakit@codeaurora.org>
Subject: [PATCH V5 2/4] arm64: dts: qcom: sc7180: Add necessary pinctrl and interrupt config for BT UART
Date: Thu, 10 Sep 2020 18:23:56 +0530	[thread overview]
Message-ID: <1599742438-16811-3-git-send-email-skakit@codeaurora.org> (raw)
In-Reply-To: <1599742438-16811-1-git-send-email-skakit@codeaurora.org>

Add a suitable sleep configuration for uart3 to support Bluetooth wakeup.

If QUP function is selected in sleep state, UART RTS/RFR is pulled high
during suspend and BT SoC not able to send wakeup bytes. So, configure
GPIO mode in sleep state to keep it low during suspend.

Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
---
Changes in V2:
 - This patch adds sleep state for BT UART. Newly added in V2.

Changes in V3:
 - Remove "output-high" for TX from both sleep and default states
   as it is not required. Configure pull-up for TX in sleep state.

Changes in V4:
 - As per Matthias's comment, removed drive-strength for sleep state
   and fixed nit-pick.

Changes in V5:
 - As per Matthias's comments, moved pinmux change for sleep state,
   pinctrl and interrupt config to the board specific file.

 arch/arm64/boot/dts/qcom/sc7180-idp.dts | 48 +++++++++++++++++++++++++++++++++
 1 file changed, 48 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 04888df..e529a41 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -344,6 +344,10 @@
 };
 
 &uart3 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-1 = <&qup_uart3_sleep>;
+	interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
+				<&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
 	status = "okay";
 
 	bluetooth: wcn3990-bt {
@@ -545,3 +549,47 @@
 	};
 };
 
+&tlmm {
+	qup_uart3_sleep: qup-uart3-sleep {
+		pinmux {
+			pins = "gpio38", "gpio39",
+			       "gpio40", "gpio41";
+			function = "gpio";
+		};
+
+		pinconf-cts {
+			/*
+			 * Configure a pull-down on CTS to match the pull of
+			 * the Bluetooth module.
+			 */
+			pins = "gpio38";
+			bias-pull-down;
+		};
+
+		pinconf-rts {
+			/*
+			 * Configure pull-down on RTS to make sure that the BT SoC can
+			 * wake up the system by sending wakeup bytes during suspend.
+			 */
+			 pins = "gpio39";
+			 bias-pull-down;
+		};
+
+		pinconf-tx {
+			/* Configure pull-up on TX when it isn't actively driven */
+			pins = "gpio40";
+			bias-pull-up;
+		};
+
+		pinconf-rx {
+			/*
+			 * Configure a pull-up on RX. This is needed to avoid
+			 * garbage data when the TX pin of the Bluetooth module is
+			 * in tri-state (module powered off or not driving the
+			 * signal yet).
+			 */
+			pins = "gpio41";
+			bias-pull-up;
+		};
+	};
+};
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation


  parent reply	other threads:[~2020-09-10 12:58 UTC|newest]

Thread overview: 19+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-09-10 12:53 [PATCH V5 0/4] Add wakeup support over UART RX satya priya
2020-09-10 12:53 ` [PATCH V5 1/4] arm64: dts: qcom: sc7180: Improve the pin config settings for CTS and TX satya priya
2020-09-10 14:40   ` Doug Anderson
2020-09-11 10:14     ` skakit
2020-09-10 12:53 ` satya priya [this message]
2020-09-10 14:40   ` [PATCH V5 2/4] arm64: dts: qcom: sc7180: Add necessary pinctrl and interrupt config for BT UART Doug Anderson
2020-09-11 10:15     ` skakit
2020-09-11 13:52       ` Bjorn Andersson
2020-09-11 15:30         ` Doug Anderson
2020-09-10 15:35   ` Matthias Kaehlcke
2020-09-11 10:15     ` skakit
2020-09-10 23:45   ` Bjorn Andersson
2020-09-11 10:16     ` skakit
2020-09-10 12:53 ` [PATCH V5 3/4] arm64: dts: qcom: sc7180-trogdor: Add " satya priya
2020-09-10 14:42   ` Doug Anderson
2020-09-11 10:15     ` skakit
2020-09-10 12:53 ` [PATCH V5 4/4] tty: serial: qcom_geni_serial: Fix the UART wakeup issue satya priya
2020-09-10 23:06   ` Bjorn Andersson
2020-09-16 12:25     ` Greg KH

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1599742438-16811-3-git-send-email-skakit@codeaurora.org \
    --to=skakit@codeaurora.org \
    --cc=agross@kernel.org \
    --cc=akashast@codeaurora.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dianders@chromium.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mka@chromium.org \
    --cc=msavaliy@qti.qualcomm.com \
    --cc=robh+dt@kernel.org \
    --cc=rojay@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.