[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

[Dieter Kiermaier]

-------- Original-Nachricht --------
> Datum: Mon, 22 Jun 2009 10:10:20 -0700
> Von: Prafulla Wadaskar <prafulla@marvell.com>
> An: "dk-arm-linux at gmx.de" <dk-arm-linux@gmx.de>, "Andr? Schwarz" <andre.schwarz@matrix-vision.de>
> CC: "u-boot at lists.denx.de" <u-boot@lists.denx.de>
> Betreff: RE: [U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

>  
> 
> > -----Original Message-----
> > From: u-boot-bounces at lists.denx.de 
> > [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Dieter Kiermaier
> > Sent: Monday, June 22, 2009 9:21 PM
> > To: Andr? Schwarz
> > Cc: u-boot at lists.denx.de
> > Subject: Re: [U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot
> > 
> > Am Montag 22 Juni 2009 17:34:35 schrieb Andr? Schwarz:
> > Andr?,
> > 
> > > Dieter,
> > >
> > > On Mon, 2009-06-22 at 17:01 +0200, Dieter Kiermaier wrote:
> > > > Am Montag 22 Juni 2009 15:08:20 schrieb Dieter Kiermaier:
> > > >
> > > > This seems to be an issue regarding Gigabit / 100MBits 
> > uplink with 
> > > > current marvell git u-boot.
> > >
> > > this gives lots of things worth looking at them :
> > >
> > > - are you running on a custom board, i.e. is MDIO known to work 
> > > properly
> > > -> PHY adressing ?
> > > - Does your chips require different clocks for 100M/1000M ?
> > > - What about mis-strapped link advertisement of the PHY ? Maybe 
> > > 100M-FD disabled ?
> > >
> > > Have you tried mii diagnostics ?
> > > Have a look at common/cmd_mii.c -> "mii info" and "mii 
> > dump" should be 
> > > your friends.
> > >
> > 
> > I don't think it's a hardware problem.
> > An older u-boot version provided from marvell works without 
> > any problems.
> Yes, this is not h/w problem, auto-speed negociation was disabled, hence
> it was not working with 100baseT, now this problem is resolved,
> Please use attached patches to resolve this for current u-boot.git 
> 
> The improved version of this driver is already mainlined you can find it
> here
> http://lists.denx.de/pipermail/u-boot/2009-June/054314.html
> 
> I am sorry I could not update the thread, niether u-boot.git on
> git.marvell.com :-(,
> I am facing some problem at my end, hopefully I will update everything by
> tomorrow.
> 
> > > > > > > >
> > > > > > > > type "save" here and "reset".
> > > > > > > >
> > > > > > > > > Environment is broken only with marvell git u-boot. 
> > > > > > > > > Preflashed u-boot find environment is ok.
> > > > > > > > > Does sheevaplug u-boot from marvell git use other 
> > > > > > > > > environment settings than preflashed u-boot?
> Yes Marvell u-boot and u-boot.git are different uses different address to
> save environment variables, so if you altered any of u-boot, environment
> will be resetted.
> 
> And they are not same on these both u-boot. u-boot.git are simple and
> minimal but enough to boot from nand.

Thanks for clarifying these, too.

> 
> > > > > > > > >
> > > > > > > > > Marvell>> printenv
> > > > > > > > > bootcmd=${x_bootcmd_kernel}; setenv bootargs 
> > ${x_bootargs}  
> > > > > > > > >${x_bootargs_root}; bootm 0x6400000;
> > > > > > > > > bootdelay=3
> > > > > > > > > baudrate=115200
> > > > > > > > > x_bootargs=console=ttyS0,115200  
> > > > > > > > 
> > >mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13
> > > > > > > > >m at 5m (roo tf s) rw x_bootcmd_kernel=nand read 0x100000 
> > > > > > > > >0x6400000  0x300000 
> > x_bootargs_root=root=/dev/mtdblock3 rw
> > > > > > > > > rootfstype=jffs2 stdin=serial  stdout=serial  
> > > > > > > > >stderr=serial
> > > > > > > > > ethaddr=00:50:43:e0:b9:d8
> > > > > > > > > ethact=egiga0
> > > > > > > > > ipaddr=192.168.2.75
> > > > > > > > >
> > > > > > > > > (ipaddr is set after bootup with setenv ipaddr 
> > > > > > > > > 192.168.2.75)
> > > > > >
> > > > > > Did you try "bootp" or "dhcp" to set up the I/F ?
> > > > >
> > > > > Yes, but everytimes the same:
> > > > > Marvell>> dhcp
> > > > > BOOTP broadcast 1
> > > > >
> > > > > ... machine hangs and only a reset helps...
> Even this problem is resolved in new driver/attached patches.
> 

Many thanks for the quick response!
Dieter
> Regards.
> Prafulla . .

-- 
GRATIS f?r alle GMX-Mitglieder: Die maxdome Movie-FLAT!
Jetzt freischalten unter http://portal.gmx.net/de/go/maxdome01

[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

[Dieter Kiermaier]

Am Montag 22 Juni 2009 17:34:35 schrieb Andr?? Schwarz:
Andr??,

> Dieter,
>
> On Mon, 2009-06-22 at 17:01 +0200, Dieter Kiermaier wrote:
> > Am Montag 22 Juni 2009 15:08:20 schrieb Dieter Kiermaier:
> >
> > This seems to be an issue regarding Gigabit / 100MBits uplink with
> > current marvell git u-boot.
>
> this gives lots of things worth looking at them :
>
> - are you running on a custom board, i.e. is MDIO known to work properly
> -> PHY adressing ?
> - Does your chips require different clocks for 100M/1000M ?
> - What about mis-strapped link advertisement of the PHY ? Maybe 100M-FD
> disabled ?
>
> Have you tried mii diagnostics ?
> Have a look at common/cmd_mii.c -> "mii info" and "mii dump" should be
> your friends.
>

I don't think it's a hardware problem.
An older u-boot version provided from marvell works without any problems.

I have contacted Prafulla from marvell. Maybe he's got an idea what's going on 
wrong there.

Thanks for helping!
Dieter


>
>
> Regards,
> Andr??
>
> > If I work with 100MBit/s network show the reported errors.
> > With gigabit connection everything seems to be working fine until now.
> >
> > Andr??, thanks for your help!
> > Dieter
> >
> > > Am Montag 22 Juni 2009 14:53:44 schrieb Andr?? Schwarz:
> > > > On Mon, 2009-06-22 at 14:41 +0200, Dieter Kiermaier wrote:
> > > > > Andr??,
> > > > >
> > > > > > Dieter,
> > > > > >
> > > > > > On Mon, 2009-06-22 at 14:04 +0200, Dieter Kiermaier wrote:
> > > > > > > Hi all,
> > > > > > >
> > > > > > > I've tried the first time booting a self compiled u-boot from
> > > > > > > git.marvell.com U-Boot can be downloaded and started with
> > > > > > > openocd quite well.
> > > > > > > Boot messages (version is dirty due to a comment in board
> > > > > > > file):
> > > > > > >
> > > > > > > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 -
> > > > > > > 13:40:45) Marvell-Sheevaplug
> > > > > > >
> > > > > > > SoC:   Kirkwood 88F6281_A0
> > > > > > > DRAM:  512 MB
> > > > > > > NAND:  512 MiB
> > > > > > > *** Warning - bad CRC or NAND, using default environment
> > > > > >
> > > > > > most propably you'll need to save the environment.
> > > > >
> > > > > Also saving environment doesn't help.
> > > > > The bad CRC message disappered as expected but that's all what
> > > > > happened.
> > > > >
> > > > > > > In:    serial
> > > > > > > Out:   serial
> > > > > > > Err:   serial
> > > > > > > Net:   egiga0
> > > > > > > 88E1116 Initialized on egiga0
> > > > > > > Hit any key to stop autoboot:  0
> > > > > > > Marvell>>
> > > > > >
> > > > > > type "save" here and "reset".
> > > > > >
> > > > > > > Environment is broken only with marvell git u-boot. Preflashed
> > > > > > > u-boot find environment is ok.
> > > > > > > Does sheevaplug u-boot from marvell git use other environment
> > > > > > > settings than preflashed u-boot?
> > > > > > >
> > > > > > > Marvell>> printenv
> > > > > > > bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs}
> > > > > > > ${x_bootargs_root}; bootm 0x6400000;
> > > > > > > bootdelay=3
> > > > > > > baudrate=115200
> > > > > > > x_bootargs=console=ttyS0,115200
> > > > > > > mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m
> > > > > > >(roo tf s) rw x_bootcmd_kernel=nand read 0x100000 0x6400000
> > > > > > > 0x300000 x_bootargs_root=root=/dev/mtdblock3 rw
> > > > > > > rootfstype=jffs2 stdin=serial
> > > > > > > stdout=serial
> > > > > > > stderr=serial
> > > > > > > ethaddr=00:50:43:e0:b9:d8
> > > > > > > ethact=egiga0
> > > > > > > ipaddr=192.168.2.75
> > > > > > >
> > > > > > > (ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
> > > >
> > > > Did you try "bootp" or "dhcp" to set up the I/F ?
> > >
> > > Yes, but everytimes the same:
> > > Marvell>> dhcp
> > > BOOTP broadcast 1
> > >
> > > ... machine hangs and only a reset helps...
> > >
> > >
> > > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> > > Marvell-Sheevaplug
> > >
> > > SoC:   Kirkwood 88F6281_A0
> > > DRAM:  512 MB
> > > NAND:  512 MiB
> > > *** Warning - bad CRC or NAND, using default environment
> > >
> > > In:    serial
> > > Out:   serial
> > > Err:   serial
> > > Net:   egiga0
> > > 88E1116 Initialized on egiga0
> > > Hit any key to stop autoboot:  0
> > > Marvell>> bootp
> > > BOOTP broadcast 1
> > >
> > > ...the same here again...
> > >
> > > It seems that the network would be activated (1 blink on the activity
> > > LED) but nothing more happens.
> > >
> > > > > > > If I now try to ping another machine in the same network:
> > > > > > > Marvell>> ping 192.168.2.251
> > > > > > > Using egiga0 device
> > > > > >
> > > > > > maybe your MAC is missing ? environment ?
> > > > >
> > > > > MAC is available in default (compiled in environment) as shown in
> > > > > env
> > >
> > > above:
> > > > > > > ethaddr=00:50:43:e0:b9:d8
> > > > >
> > > > > Also writing a new MAC to environment / savenenv / reset made no
> > > > > difference :(
> > > > >
> > > > > > > This is all what happens - no response from board, CTRL-C
> > > > > > > doesn't work. Only a hard reset will get the board up again.
> > > > > > >
> > > > > > > Do I have to change something in the default board
> > > > > > > configuration to succesfullly use networking on the sheevaplug?
> > > > > > >
> > > > > > > u-boot is build with following commands:
> > > > > > >
> > > > > > > make ARCH=arm sheevaplug_config
> > > > > > > make
> > > > > > >
> > > > > > > I get no errors during build.
> > > > > > >
> > > > > > > My gcc version is:
> > > > > > > arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
> > > > > > >
> > > > > > > Any help would be appreciated,
> > > > > > > Dieter
> > > > > >
> > > > > > Regards,
> > > > > >
> > > > > > Andr??
> > > > >
> > > > > Dieter
> > > > >
> > > > > > > _______________________________________________
> > > > > > > U-Boot mailing list
> > > > > > > U-Boot at lists.denx.de
> > > > > > > http://lists.denx.de/mailman/listinfo/u-boot
> > > > > >
> > > > > > MATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
> > > > > > Registergericht: Amtsgericht Stuttgart, HRB 271090
> > > > > > Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> > > > > > Hans-Joachim Reich
> > > >
> > > > MATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
> > > > Registergericht: Amtsgericht Stuttgart, HRB 271090
> > > > Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> > > > Hans-Joachim Reich
>
> MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
> Registergericht: Amtsgericht Stuttgart, HRB 271090
> Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> Hans-Joachim Reich

[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

[André Schwarz]

Dieter,

On Mon, 2009-06-22 at 17:01 +0200, Dieter Kiermaier wrote:
> Am Montag 22 Juni 2009 15:08:20 schrieb Dieter Kiermaier:
> 
> This seems to be an issue regarding Gigabit / 100MBits uplink with current 
> marvell git u-boot.

this gives lots of things worth looking at them :

- are you running on a custom board, i.e. is MDIO known to work properly
-> PHY adressing ?
- Does your chips require different clocks for 100M/1000M ?
- What about mis-strapped link advertisement of the PHY ? Maybe 100M-FD
disabled ?

Have you tried mii diagnostics ?
Have a look at common/cmd_mii.c -> "mii info" and "mii dump" should be
your friends.



Regards,
Andr??
> 
> If I work with 100MBit/s network show the reported errors.
> With gigabit connection everything seems to be working fine until now.
> 
> Andr??, thanks for your help!
> Dieter
> 
> 
> > Am Montag 22 Juni 2009 14:53:44 schrieb Andr?? Schwarz:
> > > On Mon, 2009-06-22 at 14:41 +0200, Dieter Kiermaier wrote:
> > > > Andr??,
> > > >
> > > > > Dieter,
> > > > >
> > > > > On Mon, 2009-06-22 at 14:04 +0200, Dieter Kiermaier wrote:
> > > > > > Hi all,
> > > > > >
> > > > > > I've tried the first time booting a self compiled u-boot from
> > > > > > git.marvell.com U-Boot can be downloaded and started with openocd
> > > > > > quite well.
> > > > > > Boot messages (version is dirty due to a comment in board file):
> > > > > >
> > > > > > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> > > > > > Marvell-Sheevaplug
> > > > > >
> > > > > > SoC:   Kirkwood 88F6281_A0
> > > > > > DRAM:  512 MB
> > > > > > NAND:  512 MiB
> > > > > > *** Warning - bad CRC or NAND, using default environment
> > > > >
> > > > > most propably you'll need to save the environment.
> > > >
> > > > Also saving environment doesn't help.
> > > > The bad CRC message disappered as expected but that's all what
> > > > happened.
> > > >
> > > > > > In:    serial
> > > > > > Out:   serial
> > > > > > Err:   serial
> > > > > > Net:   egiga0
> > > > > > 88E1116 Initialized on egiga0
> > > > > > Hit any key to stop autoboot:  0
> > > > > > Marvell>>
> > > > >
> > > > > type "save" here and "reset".
> > > > >
> > > > > > Environment is broken only with marvell git u-boot. Preflashed
> > > > > > u-boot find environment is ok.
> > > > > > Does sheevaplug u-boot from marvell git use other environment
> > > > > > settings than preflashed u-boot?
> > > > > >
> > > > > > Marvell>> printenv
> > > > > > bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs}
> > > > > > ${x_bootargs_root}; bootm 0x6400000;
> > > > > > bootdelay=3
> > > > > > baudrate=115200
> > > > > > x_bootargs=console=ttyS0,115200
> > > > > > mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(roo
> > > > > >tf s) rw x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000
> > > > > > x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
> > > > > > stdin=serial
> > > > > > stdout=serial
> > > > > > stderr=serial
> > > > > > ethaddr=00:50:43:e0:b9:d8
> > > > > > ethact=egiga0
> > > > > > ipaddr=192.168.2.75
> > > > > >
> > > > > > (ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
> > >
> > > Did you try "bootp" or "dhcp" to set up the I/F ?
> >
> > Yes, but everytimes the same:
> > Marvell>> dhcp
> > BOOTP broadcast 1
> >
> > ... machine hangs and only a reset helps...
> >
> >
> > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> > Marvell-Sheevaplug
> >
> > SoC:   Kirkwood 88F6281_A0
> > DRAM:  512 MB
> > NAND:  512 MiB
> > *** Warning - bad CRC or NAND, using default environment
> >
> > In:    serial
> > Out:   serial
> > Err:   serial
> > Net:   egiga0
> > 88E1116 Initialized on egiga0
> > Hit any key to stop autoboot:  0
> > Marvell>> bootp
> > BOOTP broadcast 1
> >
> > ...the same here again...
> >
> > It seems that the network would be activated (1 blink on the activity LED)
> > but nothing more happens.
> >
> > > > > > If I now try to ping another machine in the same network:
> > > > > > Marvell>> ping 192.168.2.251
> > > > > > Using egiga0 device
> > > > >
> > > > > maybe your MAC is missing ? environment ?
> > > >
> > > > MAC is available in default (compiled in environment) as shown in env
> >
> > above:
> > > > > > ethaddr=00:50:43:e0:b9:d8
> > > >
> > > > Also writing a new MAC to environment / savenenv / reset made no
> > > > difference :(
> > > >
> > > > > > This is all what happens - no response from board, CTRL-C doesn't
> > > > > > work. Only a hard reset will get the board up again.
> > > > > >
> > > > > > Do I have to change something in the default board configuration to
> > > > > > succesfullly use networking on the sheevaplug?
> > > > > >
> > > > > > u-boot is build with following commands:
> > > > > >
> > > > > > make ARCH=arm sheevaplug_config
> > > > > > make
> > > > > >
> > > > > > I get no errors during build.
> > > > > >
> > > > > > My gcc version is:
> > > > > > arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
> > > > > >
> > > > > > Any help would be appreciated,
> > > > > > Dieter
> > > > >
> > > > > Regards,
> > > > >
> > > > > Andr??
> > > >
> > > > Dieter
> > > >
> > > > > > _______________________________________________
> > > > > > U-Boot mailing list
> > > > > > U-Boot at lists.denx.de
> > > > > > http://lists.denx.de/mailman/listinfo/u-boot
> > > > >
> > > > > MATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
> > > > > Registergericht: Amtsgericht Stuttgart, HRB 271090
> > > > > Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> > > > > Hans-Joachim Reich
> > >
> > > MATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
> > > Registergericht: Amtsgericht Stuttgart, HRB 271090
> > > Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> > > Hans-Joachim Reich
> 
> 



MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich

[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

[Dieter Kiermaier]

Am Montag 22 Juni 2009 15:08:20 schrieb Dieter Kiermaier:

This seems to be an issue regarding Gigabit / 100MBits uplink with current 
marvell git u-boot.

If I work with 100MBit/s network show the reported errors.
With gigabit connection everything seems to be working fine until now.

Andr??, thanks for your help!
Dieter


> Am Montag 22 Juni 2009 14:53:44 schrieb Andr?? Schwarz:
> > On Mon, 2009-06-22 at 14:41 +0200, Dieter Kiermaier wrote:
> > > Andr??,
> > >
> > > > Dieter,
> > > >
> > > > On Mon, 2009-06-22 at 14:04 +0200, Dieter Kiermaier wrote:
> > > > > Hi all,
> > > > >
> > > > > I've tried the first time booting a self compiled u-boot from
> > > > > git.marvell.com U-Boot can be downloaded and started with openocd
> > > > > quite well.
> > > > > Boot messages (version is dirty due to a comment in board file):
> > > > >
> > > > > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> > > > > Marvell-Sheevaplug
> > > > >
> > > > > SoC:   Kirkwood 88F6281_A0
> > > > > DRAM:  512 MB
> > > > > NAND:  512 MiB
> > > > > *** Warning - bad CRC or NAND, using default environment
> > > >
> > > > most propably you'll need to save the environment.
> > >
> > > Also saving environment doesn't help.
> > > The bad CRC message disappered as expected but that's all what
> > > happened.
> > >
> > > > > In:    serial
> > > > > Out:   serial
> > > > > Err:   serial
> > > > > Net:   egiga0
> > > > > 88E1116 Initialized on egiga0
> > > > > Hit any key to stop autoboot:  0
> > > > > Marvell>>
> > > >
> > > > type "save" here and "reset".
> > > >
> > > > > Environment is broken only with marvell git u-boot. Preflashed
> > > > > u-boot find environment is ok.
> > > > > Does sheevaplug u-boot from marvell git use other environment
> > > > > settings than preflashed u-boot?
> > > > >
> > > > > Marvell>> printenv
> > > > > bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs}
> > > > > ${x_bootargs_root}; bootm 0x6400000;
> > > > > bootdelay=3
> > > > > baudrate=115200
> > > > > x_bootargs=console=ttyS0,115200
> > > > > mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(roo
> > > > >tf s) rw x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000
> > > > > x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
> > > > > stdin=serial
> > > > > stdout=serial
> > > > > stderr=serial
> > > > > ethaddr=00:50:43:e0:b9:d8
> > > > > ethact=egiga0
> > > > > ipaddr=192.168.2.75
> > > > >
> > > > > (ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
> >
> > Did you try "bootp" or "dhcp" to set up the I/F ?
>
> Yes, but everytimes the same:
> Marvell>> dhcp
> BOOTP broadcast 1
>
> ... machine hangs and only a reset helps...
>
>
> U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> Marvell-Sheevaplug
>
> SoC:   Kirkwood 88F6281_A0
> DRAM:  512 MB
> NAND:  512 MiB
> *** Warning - bad CRC or NAND, using default environment
>
> In:    serial
> Out:   serial
> Err:   serial
> Net:   egiga0
> 88E1116 Initialized on egiga0
> Hit any key to stop autoboot:  0
> Marvell>> bootp
> BOOTP broadcast 1
>
> ...the same here again...
>
> It seems that the network would be activated (1 blink on the activity LED)
> but nothing more happens.
>
> > > > > If I now try to ping another machine in the same network:
> > > > > Marvell>> ping 192.168.2.251
> > > > > Using egiga0 device
> > > >
> > > > maybe your MAC is missing ? environment ?
> > >
> > > MAC is available in default (compiled in environment) as shown in env
>
> above:
> > > > > ethaddr=00:50:43:e0:b9:d8
> > >
> > > Also writing a new MAC to environment / savenenv / reset made no
> > > difference :(
> > >
> > > > > This is all what happens - no response from board, CTRL-C doesn't
> > > > > work. Only a hard reset will get the board up again.
> > > > >
> > > > > Do I have to change something in the default board configuration to
> > > > > succesfullly use networking on the sheevaplug?
> > > > >
> > > > > u-boot is build with following commands:
> > > > >
> > > > > make ARCH=arm sheevaplug_config
> > > > > make
> > > > >
> > > > > I get no errors during build.
> > > > >
> > > > > My gcc version is:
> > > > > arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
> > > > >
> > > > > Any help would be appreciated,
> > > > > Dieter
> > > >
> > > > Regards,
> > > >
> > > > Andr??
> > >
> > > Dieter
> > >
> > > > > _______________________________________________
> > > > > U-Boot mailing list
> > > > > U-Boot at lists.denx.de
> > > > > http://lists.denx.de/mailman/listinfo/u-boot
> > > >
> > > > MATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
> > > > Registergericht: Amtsgericht Stuttgart, HRB 271090
> > > > Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> > > > Hans-Joachim Reich
> >
> > MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
> > Registergericht: Amtsgericht Stuttgart, HRB 271090
> > Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> > Hans-Joachim Reich

[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

[Dieter Kiermaier]

Am Montag 22 Juni 2009 14:53:44 schrieb Andr?? Schwarz:
> On Mon, 2009-06-22 at 14:41 +0200, Dieter Kiermaier wrote:
> > Andr??,
> >
> > > Dieter,
> > >
> > > On Mon, 2009-06-22 at 14:04 +0200, Dieter Kiermaier wrote:
> > > > Hi all,
> > > >
> > > > I've tried the first time booting a self compiled u-boot from
> > > > git.marvell.com U-Boot can be downloaded and started with openocd
> > > > quite well.
> > > > Boot messages (version is dirty due to a comment in board file):
> > > >
> > > > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> > > > Marvell-Sheevaplug
> > > >
> > > > SoC:   Kirkwood 88F6281_A0
> > > > DRAM:  512 MB
> > > > NAND:  512 MiB
> > > > *** Warning - bad CRC or NAND, using default environment
> > >
> > > most propably you'll need to save the environment.
> >
> > Also saving environment doesn't help.
> > The bad CRC message disappered as expected but that's all what happened.
> >
> > > > In:    serial
> > > > Out:   serial
> > > > Err:   serial
> > > > Net:   egiga0
> > > > 88E1116 Initialized on egiga0
> > > > Hit any key to stop autoboot:  0
> > > > Marvell>>
> > >
> > > type "save" here and "reset".
> > >
> > > > Environment is broken only with marvell git u-boot. Preflashed u-boot
> > > > find environment is ok.
> > > > Does sheevaplug u-boot from marvell git use other environment
> > > > settings than preflashed u-boot?
> > > >
> > > > Marvell>> printenv
> > > > bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs}
> > > > ${x_bootargs_root}; bootm 0x6400000;
> > > > bootdelay=3
> > > > baudrate=115200
> > > > x_bootargs=console=ttyS0,115200
> > > > mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootf
> > > >s) rw x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000
> > > > x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
> > > > stdin=serial
> > > > stdout=serial
> > > > stderr=serial
> > > > ethaddr=00:50:43:e0:b9:d8
> > > > ethact=egiga0
> > > > ipaddr=192.168.2.75
> > > >
> > > > (ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
>
> Did you try "bootp" or "dhcp" to set up the I/F ?
>
Yes, but everytimes the same:
Marvell>> dhcp
BOOTP broadcast 1

... machine hangs and only a reset helps...


U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
Marvell-Sheevaplug

SoC:   Kirkwood 88F6281_A0
DRAM:  512 MB
NAND:  512 MiB
*** Warning - bad CRC or NAND, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0
Marvell>> bootp
BOOTP broadcast 1

...the same here again...

It seems that the network would be activated (1 blink on the activity LED) but 
nothing more happens.


> > > > If I now try to ping another machine in the same network:
> > > > Marvell>> ping 192.168.2.251
> > > > Using egiga0 device
> > >
> > > maybe your MAC is missing ? environment ?
> >
> > MAC is available in default (compiled in environment) as shown in env 
above:
> > > > ethaddr=00:50:43:e0:b9:d8
> >
> > Also writing a new MAC to environment / savenenv / reset made no
> > difference :(
> >
> > > > This is all what happens - no response from board, CTRL-C doesn't
> > > > work. Only a hard reset will get the board up again.
> > > >
> > > > Do I have to change something in the default board configuration to
> > > > succesfullly use networking on the sheevaplug?
> > > >
> > > > u-boot is build with following commands:
> > > >
> > > > make ARCH=arm sheevaplug_config
> > > > make
> > > >
> > > > I get no errors during build.
> > > >
> > > > My gcc version is:
> > > > arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
> > > >
> > > > Any help would be appreciated,
> > > > Dieter
> > >
> > > Regards,
> > >
> > > Andr??
> >
> > Dieter
> >
> > > > _______________________________________________
> > > > U-Boot mailing list
> > > > U-Boot at lists.denx.de
> > > > http://lists.denx.de/mailman/listinfo/u-boot
> > >
> > > MATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
> > > Registergericht: Amtsgericht Stuttgart, HRB 271090
> > > Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> > > Hans-Joachim Reich
>
> MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
> Registergericht: Amtsgericht Stuttgart, HRB 271090
> Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> Hans-Joachim Reich

[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

[André Schwarz]

On Mon, 2009-06-22 at 14:41 +0200, Dieter Kiermaier wrote:
> Andr??,
> 
> > Dieter,
> >
> > On Mon, 2009-06-22 at 14:04 +0200, Dieter Kiermaier wrote:
> > > Hi all,
> > >
> > > I've tried the first time booting a self compiled u-boot from
> > > git.marvell.com U-Boot can be downloaded and started with openocd quite
> > > well.
> > > Boot messages (version is dirty due to a comment in board file):
> > >
> > > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> > > Marvell-Sheevaplug
> > >
> > > SoC:   Kirkwood 88F6281_A0
> > > DRAM:  512 MB
> > > NAND:  512 MiB
> > > *** Warning - bad CRC or NAND, using default environment
> >
> > most propably you'll need to save the environment.
> 
> Also saving environment doesn't help.
> The bad CRC message disappered as expected but that's all what happened.
> 
> >
> > > In:    serial
> > > Out:   serial
> > > Err:   serial
> > > Net:   egiga0
> > > 88E1116 Initialized on egiga0
> > > Hit any key to stop autoboot:  0
> > > Marvell>>
> >
> > type "save" here and "reset".
> >
> > > Environment is broken only with marvell git u-boot. Preflashed u-boot
> > > find environment is ok.
> > > Does sheevaplug u-boot from marvell git use other environment settings
> > > than preflashed u-boot?
> > >
> > > Marvell>> printenv
> > > bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs}
> > > ${x_bootargs_root}; bootm 0x6400000;
> > > bootdelay=3
> > > baudrate=115200
> > > x_bootargs=console=ttyS0,115200
> > > mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs)
> > > rw x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000
> > > x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
> > > stdin=serial
> > > stdout=serial
> > > stderr=serial
> > > ethaddr=00:50:43:e0:b9:d8
> > > ethact=egiga0
> > > ipaddr=192.168.2.75
> > >
> > > (ipaddr is set after bootup with setenv ipaddr 192.168.2.75)

Did you try "bootp" or "dhcp" to set up the I/F ?

> > >
> > > If I now try to ping another machine in the same network:
> > > Marvell>> ping 192.168.2.251
> > > Using egiga0 device
> >
> > maybe your MAC is missing ? environment ?
> 
> MAC is available in default (compiled in environment) as shown in env above:
> > > ethaddr=00:50:43:e0:b9:d8
> Also writing a new MAC to environment / savenenv / reset made no difference :(
> 
> >
> > > This is all what happens - no response from board, CTRL-C doesn't work.
> > > Only a hard reset will get the board up again.
> > >
> > > Do I have to change something in the default board configuration to
> > > succesfullly use networking on the sheevaplug?
> > >
> > > u-boot is build with following commands:
> > >
> > > make ARCH=arm sheevaplug_config
> > > make
> > >
> > > I get no errors during build.
> > >
> > > My gcc version is:
> > > arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
> > >
> > > Any help would be appreciated,
> > > Dieter
> >
> > Regards,
> >
> > Andr??
> >
> Dieter
> 
> 
> > > _______________________________________________
> > > U-Boot mailing list
> > > U-Boot at lists.denx.de
> > > http://lists.denx.de/mailman/listinfo/u-boot
> >
> > MATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
> > Registergericht: Amtsgericht Stuttgart, HRB 271090
> > Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> > Hans-Joachim Reich
> 
> 



MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich

[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

[Dieter Kiermaier]

Andr??,

> Dieter,
>
> On Mon, 2009-06-22 at 14:04 +0200, Dieter Kiermaier wrote:
> > Hi all,
> >
> > I've tried the first time booting a self compiled u-boot from
> > git.marvell.com U-Boot can be downloaded and started with openocd quite
> > well.
> > Boot messages (version is dirty due to a comment in board file):
> >
> > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> > Marvell-Sheevaplug
> >
> > SoC:   Kirkwood 88F6281_A0
> > DRAM:  512 MB
> > NAND:  512 MiB
> > *** Warning - bad CRC or NAND, using default environment
>
> most propably you'll need to save the environment.

Also saving environment doesn't help.
The bad CRC message disappered as expected but that's all what happened.

>
> > In:    serial
> > Out:   serial
> > Err:   serial
> > Net:   egiga0
> > 88E1116 Initialized on egiga0
> > Hit any key to stop autoboot:  0
> > Marvell>>
>
> type "save" here and "reset".
>
> > Environment is broken only with marvell git u-boot. Preflashed u-boot
> > find environment is ok.
> > Does sheevaplug u-boot from marvell git use other environment settings
> > than preflashed u-boot?
> >
> > Marvell>> printenv
> > bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs}
> > ${x_bootargs_root}; bootm 0x6400000;
> > bootdelay=3
> > baudrate=115200
> > x_bootargs=console=ttyS0,115200
> > mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs)
> > rw x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000
> > x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
> > stdin=serial
> > stdout=serial
> > stderr=serial
> > ethaddr=00:50:43:e0:b9:d8
> > ethact=egiga0
> > ipaddr=192.168.2.75
> >
> > (ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
> >
> > If I now try to ping another machine in the same network:
> > Marvell>> ping 192.168.2.251
> > Using egiga0 device
>
> maybe your MAC is missing ? environment ?

MAC is available in default (compiled in environment) as shown in env above:
> > ethaddr=00:50:43:e0:b9:d8
Also writing a new MAC to environment / savenenv / reset made no difference :(

>
> > This is all what happens - no response from board, CTRL-C doesn't work.
> > Only a hard reset will get the board up again.
> >
> > Do I have to change something in the default board configuration to
> > succesfullly use networking on the sheevaplug?
> >
> > u-boot is build with following commands:
> >
> > make ARCH=arm sheevaplug_config
> > make
> >
> > I get no errors during build.
> >
> > My gcc version is:
> > arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
> >
> > Any help would be appreciated,
> > Dieter
>
> Regards,
>
> Andr??
>
Dieter


> > _______________________________________________
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > http://lists.denx.de/mailman/listinfo/u-boot
>
> MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
> Registergericht: Amtsgericht Stuttgart, HRB 271090
> Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> Hans-Joachim Reich

[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

[André Schwarz]

Dieter,

On Mon, 2009-06-22 at 14:04 +0200, Dieter Kiermaier wrote:
> Hi all,
> 
> I've tried the first time booting a self compiled u-boot from git.marvell.com 
> U-Boot can be downloaded and started with openocd quite well.
> Boot messages (version is dirty due to a comment in board file):
> 
> U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> Marvell-Sheevaplug
> 
> SoC:   Kirkwood 88F6281_A0
> DRAM:  512 MB
> NAND:  512 MiB
> *** Warning - bad CRC or NAND, using default environment

most propably you'll need to save the environment.

> 
> In:    serial
> Out:   serial
> Err:   serial
> Net:   egiga0
> 88E1116 Initialized on egiga0
> Hit any key to stop autoboot:  0
> Marvell>>

type "save" here and "reset".

> 
> 
> Environment is broken only with marvell git u-boot. Preflashed u-boot find 
> environment is ok.
> Does sheevaplug u-boot from marvell git use other environment settings than 
> preflashed u-boot?
> 
> Marvell>> printenv
> bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; 
> bootm 0x6400000;
> bootdelay=3
> baudrate=115200
> x_bootargs=console=ttyS0,115200 
> mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs) rw
> x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000
> x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
> stdin=serial
> stdout=serial
> stderr=serial
> ethaddr=00:50:43:e0:b9:d8
> ethact=egiga0
> ipaddr=192.168.2.75
> 
> (ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
> 
> If I now try to ping another machine in the same network:
> Marvell>> ping 192.168.2.251
> Using egiga0 device

maybe your MAC is missing ? environment ?

> 
> 
> 
> This is all what happens - no response from board, CTRL-C doesn't work.
> Only a hard reset will get the board up again.
> 
> Do I have to change something in the default board configuration to 
> succesfullly use networking on the sheevaplug?
> 
> u-boot is build with following commands:
> 
> make ARCH=arm sheevaplug_config
> make
> 
> I get no errors during build.
> 
> My gcc version is:
> arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
> 
> Any help would be appreciated,
> Dieter
> 
> 
Regards,

Andr??
> 
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot



MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich

[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

[Dieter Kiermaier]

Hi all,

I've tried the first time booting a self compiled u-boot from git.marvell.com 
U-Boot can be downloaded and started with openocd quite well.
Boot messages (version is dirty due to a comment in board file):

U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
Marvell-Sheevaplug

SoC:   Kirkwood 88F6281_A0
DRAM:  512 MB
NAND:  512 MiB
*** Warning - bad CRC or NAND, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0
Marvell>>


Environment is broken only with marvell git u-boot. Preflashed u-boot find 
environment is ok.
Does sheevaplug u-boot from marvell git use other environment settings than 
preflashed u-boot?

Marvell>> printenv
bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; 
bootm 0x6400000;
bootdelay=3
baudrate=115200
x_bootargs=console=ttyS0,115200 
mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs) rw
x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000
x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
stdin=serial
stdout=serial
stderr=serial
ethaddr=00:50:43:e0:b9:d8
ethact=egiga0
ipaddr=192.168.2.75

(ipaddr is set after bootup with setenv ipaddr 192.168.2.75)

If I now try to ping another machine in the same network:
Marvell>> ping 192.168.2.251
Using egiga0 device



This is all what happens - no response from board, CTRL-C doesn't work.
Only a hard reset will get the board up again.

Do I have to change something in the default board configuration to 
succesfullly use networking on the sheevaplug?

u-boot is build with following commands:

make ARCH=arm sheevaplug_config
make

I get no errors during build.

My gcc version is:
arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)

Any help would be appreciated,
Dieter