[PATCH v3 0/3] can: at91_can: fix for errata 50.2.6.3 & 50.3.5.3

[PATCH v3 0/3] can: at91_can: fix for errata 50.2.6.3 & 50.3.5.3

[Marc Kleine-Budde]

Hello,

as promised I've implemented the proposed workaround for the errata
50.2.6.3 & 50.3.5.3:
"Contents of Mailbox 0 can be sent Even if Mailbox is Disabled"

This means under high bus load it can happen that the mailbox 0 is send
to the bus. And it does happen, even with the mainline driver where
Mailbox 0 is a receive mailbox. The errata proposes not to use mailbox 0
and load it with an unused can_id that will not disturb the bus.

The first patch cleans up the driver without any functional changes, so
that the mailbox 0 can be disabled in the second patch. The third patch
adds a sysfs parameter to the driver, so that the identifier of mailbox 0
can configured.

This series applies to net-2.6/master. It has been tested on a ronetix pm9263
board against a PCI-SJA1000 card with the canfdtest utility and on custom
at91 boards against each other.

changes since v2:
- rebased to current net-2.6/master
- added Acked-by (Thanks to Kurt Van Dijck, Wolfgang Grandegger
  and Wolfram Sang)

regards, Marc

[PATCH v3 1/3] can: at91_can: clean up usage of AT91_MB_RX_FIRST and AT91_MB_RX_NUM

[Marc Kleine-Budde]

This patch cleans up the usage of two macros which specify the mailbox
usage. AT91_MB_RX_FIRST and AT91_MB_RX_NUM define the first and the
number of RX mailboxes. The current driver uses these variables in an
unclean way; assuming that AT91_MB_RX_FIRST is 0;

This patch cleans up the usage of these macros, no longer assuming
AT91_MB_RX_FIRST == 0.

Signed-off-by: Marc Kleine-Budde <mkl-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
Acked-by: Wolfgang Grandegger <wg-5Yr1BZd7O62+XT7JhA+gdA@public.gmane.org>
---
 drivers/net/can/at91_can.c |   18 ++++++++++--------
 1 files changed, 10 insertions(+), 8 deletions(-)

diff --git a/drivers/net/can/at91_can.c b/drivers/net/can/at91_can.c
index 7ef83d0..892c3d8 100644
--- a/drivers/net/can/at91_can.c
+++ b/drivers/net/can/at91_can.c
@@ -2,7 +2,7 @@
  * at91_can.c - CAN network driver for AT91 SoC CAN controller
  *
  * (C) 2007 by Hans J. Koch <hjk-vqZO0P4V72/QD6PfKP4TzA@public.gmane.org>
- * (C) 2008, 2009, 2010 by Marc Kleine-Budde <kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
+ * (C) 2008, 2009, 2010, 2011 by Marc Kleine-Budde <kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
  *
  * This software may be distributed under the terms of the GNU General
  * Public License ("GPL") version 2 as distributed in the 'COPYING'
@@ -55,7 +55,8 @@
 #define AT91_MB_RX_MASK(i)	((1 << (i)) - 1)
 #define AT91_MB_RX_SPLIT	8
 #define AT91_MB_RX_LOW_LAST	(AT91_MB_RX_SPLIT - 1)
-#define AT91_MB_RX_LOW_MASK	(AT91_MB_RX_MASK(AT91_MB_RX_SPLIT))
+#define AT91_MB_RX_LOW_MASK	(AT91_MB_RX_MASK(AT91_MB_RX_SPLIT) & \
+				 ~AT91_MB_RX_MASK(AT91_MB_RX_FIRST))
 
 #define AT91_MB_TX_NUM		(1 << AT91_MB_TX_SHIFT)
 #define AT91_MB_TX_FIRST	(AT91_MB_RX_LAST + 1)
@@ -254,7 +255,8 @@ static void at91_setup_mailboxes(struct net_device *dev)
 		set_mb_mode_prio(priv, i, AT91_MB_MODE_TX, 0);
 
 	/* Reset tx and rx helper pointers */
-	priv->tx_next = priv->tx_echo = priv->rx_next = 0;
+	priv->tx_next = priv->tx_echo = 0;
+	priv->rx_next = AT91_MB_RX_FIRST;
 }
 
 static int at91_set_bittiming(struct net_device *dev)
@@ -590,10 +592,10 @@ static int at91_poll_rx(struct net_device *dev, int quota)
 			"order of incoming frames cannot be guaranteed\n");
 
  again:
-	for (mb = find_next_bit(addr, AT91_MB_RX_NUM, priv->rx_next);
-	     mb < AT91_MB_RX_NUM && quota > 0;
+	for (mb = find_next_bit(addr, AT91_MB_RX_LAST + 1, priv->rx_next);
+	     mb < AT91_MB_RX_LAST + 1 && quota > 0;
 	     reg_sr = at91_read(priv, AT91_SR),
-	     mb = find_next_bit(addr, AT91_MB_RX_NUM, ++priv->rx_next)) {
+	     mb = find_next_bit(addr, AT91_MB_RX_LAST + 1, ++priv->rx_next)) {
 		at91_read_msg(dev, mb);
 
 		/* reactivate mailboxes */
@@ -610,8 +612,8 @@ static int at91_poll_rx(struct net_device *dev, int quota)
 
 	/* upper group completed, look again in lower */
 	if (priv->rx_next > AT91_MB_RX_LOW_LAST &&
-	    quota > 0 && mb >= AT91_MB_RX_NUM) {
-		priv->rx_next = 0;
+	    quota > 0 && mb > AT91_MB_RX_LAST) {
+		priv->rx_next = AT91_MB_RX_FIRST;
 		goto again;
 	}
 
-- 
1.7.2.3

[PATCH v3 2/3] can: at91_can: don't use mailbox 0

[Marc Kleine-Budde]

Due to a chip bug (errata 50.2.6.3 & 50.3.5.3 in
"AT91SAM9263 Preliminary 6249H-ATARM-27-Jul-09") the contents of mailbox
0 may be send under certain conditions (even if disabled or in rx mode).

The workaround in the errata suggests not to use the mailbox and load it
with a unused identifier.

This patch implements the first part of the workaround, it updates
AT91_MB_RX_NUM and AT91_MB_RX_FIRST (and the inline documentation)
so that mailbox 0 stays unused.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
---
 drivers/net/can/at91_can.c |   32 ++++++++++++++++++++------------
 1 files changed, 20 insertions(+), 12 deletions(-)

diff --git a/drivers/net/can/at91_can.c b/drivers/net/can/at91_can.c
index 892c3d8..16e45a5 100644
--- a/drivers/net/can/at91_can.c
+++ b/drivers/net/can/at91_can.c
@@ -40,16 +40,16 @@
 
 #include <mach/board.h>
 
-#define AT91_NAPI_WEIGHT	12
+#define AT91_NAPI_WEIGHT	11
 
 /*
  * RX/TX Mailbox split
  * don't dare to touch
  */
-#define AT91_MB_RX_NUM		12
+#define AT91_MB_RX_NUM		11
 #define AT91_MB_TX_SHIFT	2
 
-#define AT91_MB_RX_FIRST	0
+#define AT91_MB_RX_FIRST	1
 #define AT91_MB_RX_LAST		(AT91_MB_RX_FIRST + AT91_MB_RX_NUM - 1)
 
 #define AT91_MB_RX_MASK(i)	((1 << (i)) - 1)
@@ -236,10 +236,14 @@ static void at91_setup_mailboxes(struct net_device *dev)
 	unsigned int i;
 
 	/*
-	 * The first 12 mailboxes are used as a reception FIFO. The
-	 * last mailbox is configured with overwrite option. The
-	 * overwrite flag indicates a FIFO overflow.
+	 * Due to a chip bug (errata 50.2.6.3 & 50.3.5.3) the first
+	 * mailbox is disabled. The next 11 mailboxes are used as a
+	 * reception FIFO. The last mailbox is configured with
+	 * overwrite option. The overwrite flag indicates a FIFO
+	 * overflow.
 	 */
+	for (i = 0; i < AT91_MB_RX_FIRST; i++)
+		set_mb_mode(priv, i, AT91_MB_MODE_DISABLED);
 	for (i = AT91_MB_RX_FIRST; i < AT91_MB_RX_LAST; i++)
 		set_mb_mode(priv, i, AT91_MB_MODE_RX);
 	set_mb_mode(priv, AT91_MB_RX_LAST, AT91_MB_MODE_RX_OVRWR);
@@ -541,27 +545,31 @@ static void at91_read_msg(struct net_device *dev, unsigned int mb)
  *
  * Theory of Operation:
  *
- * 12 of the 16 mailboxes on the chip are reserved for RX. we split
- * them into 2 groups. The lower group holds 8 and upper 4 mailboxes.
+ * 11 of the 16 mailboxes on the chip are reserved for RX. we split
+ * them into 2 groups. The lower group holds 7 and upper 4 mailboxes.
  *
  * Like it or not, but the chip always saves a received CAN message
  * into the first free mailbox it finds (starting with the
  * lowest). This makes it very difficult to read the messages in the
  * right order from the chip. This is how we work around that problem:
  *
- * The first message goes into mb nr. 0 and issues an interrupt. All
+ * The first message goes into mb nr. 1 and issues an interrupt. All
  * rx ints are disabled in the interrupt handler and a napi poll is
  * scheduled. We read the mailbox, but do _not_ reenable the mb (to
  * receive another message).
  *
  *    lower mbxs      upper
- *   ______^______    __^__
- *  /             \  /     \
+ *     ____^______    __^__
+ *    /           \  /     \
  * +-+-+-+-+-+-+-+-++-+-+-+-+
- * |x|x|x|x|x|x|x|x|| | | | |
+ * | |x|x|x|x|x|x|x|| | | | |
  * +-+-+-+-+-+-+-+-++-+-+-+-+
  *  0 0 0 0 0 0  0 0 0 0 1 1  \ mail
  *  0 1 2 3 4 5  6 7 8 9 0 1  / box
+ *  ^
+ *  |
+ *   \
+ *     unused, due to chip bug
  *
  * The variable priv->rx_next points to the next mailbox to read a
  * message from. As long we're in the lower mailboxes we just read the
-- 
1.7.2.3

[PATCH v3 3/3] can: at91_can: make can_id of mailbox 0 configurable

[Marc Kleine-Budde]

Due to a chip bug (errata 50.2.6.3 & 50.3.5.3 in
"AT91SAM9263 Preliminary 6249H-ATARM-27-Jul-09") the contents of mailbox
0 may be send under certain conditions (even if disabled or in rx mode).

The workaround in the errata suggests not to use the mailbox and load it
with an unused identifier.

This patch implements the second part of the workaround. A sysfs entry
"mb0_id" is introduced. While the interface is down it can be used to
configure the can_id of mailbox 0. The default value id 0x7ff.

In order to use an extended can_id add the CAN_EFF_FLAG (0x80000000U)
to the can_id. Example:

- standard id 0x7ff:
echo 0x7ff      > /sys/class/net/can0/mb0_id

- extended id 0x1fffffff:
echo 0x9fffffff > /sys/class/net/can0/mb0_id

Signed-off-by: Marc Kleine-Budde <mkl-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
Acked-by: Wolfgang Grandegger <wg-5Yr1BZd7O62+XT7JhA+gdA@public.gmane.org>
Acked-by: Kurt Van Dijck <kurt.van.dijck-/BeEPy95v10@public.gmane.org>
For the Documentation-part:
Acked-by: Wolfram Sang <w.sang-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
---
 Documentation/ABI/testing/sysfs-platform-at91 |   25 +++++++
 drivers/net/can/at91_can.c                    |   90 +++++++++++++++++++++++--
 2 files changed, 108 insertions(+), 7 deletions(-)
 create mode 100644 Documentation/ABI/testing/sysfs-platform-at91

diff --git a/Documentation/ABI/testing/sysfs-platform-at91 b/Documentation/ABI/testing/sysfs-platform-at91
new file mode 100644
index 0000000..4cc6a86
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-platform-at91
@@ -0,0 +1,25 @@
+What:		/sys/devices/platform/at91_can/net/<iface>/mb0_id
+Date:		January 2011
+KernelVersion:	2.6.38
+Contact:	Marc Kleine-Budde <kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
+Description:
+		Value representing the can_id of mailbox 0.
+
+		Default: 0x7ff (standard frame)
+
+		Due to a chip bug (errata 50.2.6.3 & 50.3.5.3 in
+		"AT91SAM9263 Preliminary 6249H-ATARM-27-Jul-09") the
+		contents of mailbox 0 may be send under certain
+		conditions (even if disabled or in rx mode).
+
+		The workaround in the errata suggests not to use the
+		mailbox and load it with an unused identifier.
+
+		In order to use an extended can_id add the
+		CAN_EFF_FLAG (0x80000000U) to the can_id. Example:
+
+		- standard id 0x7ff:
+		echo 0x7ff      > /sys/class/net/can0/mb0_id
+
+		- extended id 0x1fffffff:
+		echo 0x9fffffff > /sys/class/net/can0/mb0_id
diff --git a/drivers/net/can/at91_can.c b/drivers/net/can/at91_can.c
index 16e45a5..2532b96 100644
--- a/drivers/net/can/at91_can.c
+++ b/drivers/net/can/at91_can.c
@@ -30,6 +30,7 @@
 #include <linux/module.h>
 #include <linux/netdevice.h>
 #include <linux/platform_device.h>
+#include <linux/rtnetlink.h>
 #include <linux/skbuff.h>
 #include <linux/spinlock.h>
 #include <linux/string.h>
@@ -169,6 +170,8 @@ struct at91_priv {
 
 	struct clk		*clk;
 	struct at91_can_data	*pdata;
+
+	canid_t			mb0_id;
 };
 
 static struct can_bittiming_const at91_bittiming_const = {
@@ -221,6 +224,18 @@ static inline void set_mb_mode(const struct at91_priv *priv, unsigned int mb,
 	set_mb_mode_prio(priv, mb, mode, 0);
 }
 
+static inline u32 at91_can_id_to_reg_mid(canid_t can_id)
+{
+	u32 reg_mid;
+
+	if (can_id & CAN_EFF_FLAG)
+		reg_mid = (can_id & CAN_EFF_MASK) | AT91_MID_MIDE;
+	else
+		reg_mid = (can_id & CAN_SFF_MASK) << 18;
+
+	return reg_mid;
+}
+
 /*
  * Swtich transceiver on or off
  */
@@ -234,6 +249,7 @@ static void at91_setup_mailboxes(struct net_device *dev)
 {
 	struct at91_priv *priv = netdev_priv(dev);
 	unsigned int i;
+	u32 reg_mid;
 
 	/*
 	 * Due to a chip bug (errata 50.2.6.3 & 50.3.5.3) the first
@@ -242,8 +258,13 @@ static void at91_setup_mailboxes(struct net_device *dev)
 	 * overwrite option. The overwrite flag indicates a FIFO
 	 * overflow.
 	 */
-	for (i = 0; i < AT91_MB_RX_FIRST; i++)
+	reg_mid = at91_can_id_to_reg_mid(priv->mb0_id);
+	for (i = 0; i < AT91_MB_RX_FIRST; i++) {
 		set_mb_mode(priv, i, AT91_MB_MODE_DISABLED);
+		at91_write(priv, AT91_MID(i), reg_mid);
+		at91_write(priv, AT91_MCR(i), 0x0);	/* clear dlc */
+	}
+
 	for (i = AT91_MB_RX_FIRST; i < AT91_MB_RX_LAST; i++)
 		set_mb_mode(priv, i, AT91_MB_MODE_RX);
 	set_mb_mode(priv, AT91_MB_RX_LAST, AT91_MB_MODE_RX_OVRWR);
@@ -378,12 +399,7 @@ static netdev_tx_t at91_start_xmit(struct sk_buff *skb, struct net_device *dev)
 		netdev_err(dev, "BUG! TX buffer full when queue awake!\n");
 		return NETDEV_TX_BUSY;
 	}
-
-	if (cf->can_id & CAN_EFF_FLAG)
-		reg_mid = (cf->can_id & CAN_EFF_MASK) | AT91_MID_MIDE;
-	else
-		reg_mid = (cf->can_id & CAN_SFF_MASK) << 18;
-
+	reg_mid = at91_can_id_to_reg_mid(cf->can_id);
 	reg_mcr = ((cf->can_id & CAN_RTR_FLAG) ? AT91_MCR_MRTR : 0) |
 		(cf->can_dlc << 16) | AT91_MCR_MTCR;
 
@@ -1047,6 +1063,64 @@ static const struct net_device_ops at91_netdev_ops = {
 	.ndo_start_xmit	= at91_start_xmit,
 };
 
+static ssize_t at91_sysfs_show_mb0_id(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct at91_priv *priv = netdev_priv(to_net_dev(dev));
+
+	if (priv->mb0_id & CAN_EFF_FLAG)
+		return snprintf(buf, PAGE_SIZE, "0x%08x\n", priv->mb0_id);
+	else
+		return snprintf(buf, PAGE_SIZE, "0x%03x\n", priv->mb0_id);
+}
+
+static ssize_t at91_sysfs_set_mb0_id(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct net_device *ndev = to_net_dev(dev);
+	struct at91_priv *priv = netdev_priv(ndev);
+	unsigned long can_id;
+	ssize_t ret;
+	int err;
+
+	rtnl_lock();
+
+	if (ndev->flags & IFF_UP) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	err = strict_strtoul(buf, 0, &can_id);
+	if (err) {
+		ret = err;
+		goto out;
+	}
+
+	if (can_id & CAN_EFF_FLAG)
+		can_id &= CAN_EFF_MASK | CAN_EFF_FLAG;
+	else
+		can_id &= CAN_SFF_MASK;
+
+	priv->mb0_id = can_id;
+	ret = count;
+
+ out:
+	rtnl_unlock();
+	return ret;
+}
+
+static DEVICE_ATTR(mb0_id, S_IWUGO | S_IRUGO,
+	at91_sysfs_show_mb0_id, at91_sysfs_set_mb0_id);
+
+static struct attribute *at91_sysfs_attrs[] = {
+	&dev_attr_mb0_id.attr,
+	NULL,
+};
+
+static struct attribute_group at91_sysfs_attr_group = {
+	.attrs = at91_sysfs_attrs,
+};
+
 static int __devinit at91_can_probe(struct platform_device *pdev)
 {
 	struct net_device *dev;
@@ -1092,6 +1166,7 @@ static int __devinit at91_can_probe(struct platform_device *pdev)
 	dev->netdev_ops	= &at91_netdev_ops;
 	dev->irq = irq;
 	dev->flags |= IFF_ECHO;
+	dev->sysfs_groups[0] = &at91_sysfs_attr_group;
 
 	priv = netdev_priv(dev);
 	priv->can.clock.freq = clk_get_rate(clk);
@@ -1103,6 +1178,7 @@ static int __devinit at91_can_probe(struct platform_device *pdev)
 	priv->dev = dev;
 	priv->clk = clk;
 	priv->pdata = pdev->dev.platform_data;
+	priv->mb0_id = 0x7ff;
 
 	netif_napi_add(dev, &priv->napi, at91_poll, AT91_NAPI_WEIGHT);
 
-- 
1.7.2.3

Re: [PATCH v3 0/3] can: at91_can: fix for errata 50.2.6.3 & 50.3.5.3

[Marc Kleine-Budde]

[-- Attachment #1.1: Type: text/plain, Size: 2083 bytes --]

On 01/24/2011 03:15 PM, Marc Kleine-Budde wrote:
> Hello,
> 
> as promised I've implemented the proposed workaround for the errata
> 50.2.6.3 & 50.3.5.3:
> "Contents of Mailbox 0 can be sent Even if Mailbox is Disabled"
> 
> This means under high bus load it can happen that the mailbox 0 is send
> to the bus. And it does happen, even with the mainline driver where
> Mailbox 0 is a receive mailbox. The errata proposes not to use mailbox 0
> and load it with an unused can_id that will not disturb the bus.
> 
> The first patch cleans up the driver without any functional changes, so
> that the mailbox 0 can be disabled in the second patch. The third patch
> adds a sysfs parameter to the driver, so that the identifier of mailbox 0
> can configured.
> 
> This series applies to net-2.6/master. It has been tested on a ronetix pm9263
> board against a PCI-SJA1000 card with the canfdtest utility and on custom
> at91 boards against each other.

I've updated the patch series in my git-repo, too.

The following changes since commit b30532515f0a62bfe17207ab00883dd262497006:

  bonding: Ensure that we unshare skbs prior to calling pskb_may_pull (2011-01-20 16:45:56 -0800)

are available in the git repository at:
  git://git.pengutronix.de/git/mkl/linux-2.6.git can/at91_can-for-net-2.6

Marc Kleine-Budde (3):
      can: at91_can: clean up usage of AT91_MB_RX_FIRST and AT91_MB_RX_NUM
      can: at91_can: don't use mailbox 0
      can: at91_can: make can_id of mailbox 0 configurable

 Documentation/ABI/testing/sysfs-platform-at91 |   25 +++++
 drivers/net/can/at91_can.c                    |  138 ++++++++++++++++++++-----
 2 files changed, 137 insertions(+), 26 deletions(-)
 create mode 100644 Documentation/ABI/testing/sysfs-platform-at91

regards, Marc

-- 
Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |


[-- Attachment #1.2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 262 bytes --]

[-- Attachment #2: Type: text/plain, Size: 188 bytes --]

_______________________________________________
Socketcan-core mailing list
Socketcan-core-0fE9KPoRgkgATYTw5x5z8w@public.gmane.org
https://lists.berlios.de/mailman/listinfo/socketcan-core

Re: [PATCH v3 0/3] can: at91_can: fix for errata 50.2.6.3 & 50.3.5.3

[David Miller]

From: Marc Kleine-Budde <mkl@pengutronix.de>
Date: Mon, 24 Jan 2011 15:19:16 +0100

> I've updated the patch series in my git-repo, too.
> 
> The following changes since commit b30532515f0a62bfe17207ab00883dd262497006:
> 
>   bonding: Ensure that we unshare skbs prior to calling pskb_may_pull (2011-01-20 16:45:56 -0800)
> 
> are available in the git repository at:
>   git://git.pengutronix.de/git/mkl/linux-2.6.git can/at91_can-for-net-2.6
> 
> Marc Kleine-Budde (3):
>       can: at91_can: clean up usage of AT91_MB_RX_FIRST and AT91_MB_RX_NUM
>       can: at91_can: don't use mailbox 0
>       can: at91_can: make can_id of mailbox 0 configurable

Pulled into net-2.6, thanks Marc.