[PATCH v2 0/2] net: davinci_mdio: reuse for keystone2 arch

[PATCH v2 0/2] net: davinci_mdio: reuse for keystone2 arch

[Grygorii Strashko]

The similar MDIO HW blocks is used by keystone 2 SoCs as
in Davinci SoCs:
- one in Gigabit Ethernet (GbE) Switch Subsystem
  See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
- one in 10 Gigabit Ethernet Subsystem
  See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf

Hence, reuse Davinci MDIO driver for Keystone 2 and
enable TI networking for Keystone 2 devices.

Also, as part of this series, enable PHY's creation from DT, because
Keystone 2 supports DT boot mode only.

Changes in v2:
- review comments applied. 
  Keystone 2 compatibility string changed to "ti,keystone_mdio".

Grygorii Strashko (2):
  net: davinci_mdio: reuse for keystone2 arch
  net: davinci_mdio: allow to create phys from dt

 .../devicetree/bindings/net/davinci-mdio.txt       |    8 ++++----
 drivers/net/ethernet/ti/Kconfig                    |    4 ++--
 drivers/net/ethernet/ti/davinci_mdio.c             |   21 ++++++++++++++++++--
 3 files changed, 25 insertions(+), 8 deletions(-)

-- 
1.7.9.5

[PATCH v2 0/2] net: davinci_mdio: reuse for keystone2 arch

[Grygorii Strashko]

The similar MDIO HW blocks is used by keystone 2 SoCs as
in Davinci SoCs:
- one in Gigabit Ethernet (GbE) Switch Subsystem
  See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
- one in 10 Gigabit Ethernet Subsystem
  See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf

Hence, reuse Davinci MDIO driver for Keystone 2 and
enable TI networking for Keystone 2 devices.

Also, as part of this series, enable PHY's creation from DT, because
Keystone 2 supports DT boot mode only.

Changes in v2:
- review comments applied. 
  Keystone 2 compatibility string changed to "ti,keystone_mdio".

Grygorii Strashko (2):
  net: davinci_mdio: reuse for keystone2 arch
  net: davinci_mdio: allow to create phys from dt

 .../devicetree/bindings/net/davinci-mdio.txt       |    8 ++++----
 drivers/net/ethernet/ti/Kconfig                    |    4 ++--
 drivers/net/ethernet/ti/davinci_mdio.c             |   21 ++++++++++++++++++--
 3 files changed, 25 insertions(+), 8 deletions(-)

-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 0/2] net: davinci_mdio: reuse for keystone2 arch

[Grygorii Strashko]

The similar MDIO HW blocks is used by keystone 2 SoCs as
in Davinci SoCs:
- one in Gigabit Ethernet (GbE) Switch Subsystem
  See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
- one in 10 Gigabit Ethernet Subsystem
  See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf

Hence, reuse Davinci MDIO driver for Keystone 2 and
enable TI networking for Keystone 2 devices.

Also, as part of this series, enable PHY's creation from DT, because
Keystone 2 supports DT boot mode only.

Changes in v2:
- review comments applied. 
  Keystone 2 compatibility string changed to "ti,keystone_mdio".

Grygorii Strashko (2):
  net: davinci_mdio: reuse for keystone2 arch
  net: davinci_mdio: allow to create phys from dt

 .../devicetree/bindings/net/davinci-mdio.txt       |    8 ++++----
 drivers/net/ethernet/ti/Kconfig                    |    4 ++--
 drivers/net/ethernet/ti/davinci_mdio.c             |   21 ++++++++++++++++++--
 3 files changed, 25 insertions(+), 8 deletions(-)

-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 1/2] net: davinci_mdio: reuse for keystone2 arch

[Grygorii Strashko]

The similar MDIO HW blocks is used by keystone 2 SoCs as
in Davinci SoCs:
- one in Gigabit Ethernet (GbE) Switch Subsystem
  See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
- one in 10 Gigabit Ethernet Subsystem
  See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf

Hence, reuse Davinci MDIO driver for Keystone 2 and
enable TI networking for Keystone 2 devices

Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
 .../devicetree/bindings/net/davinci-mdio.txt       |    8 ++++----
 drivers/net/ethernet/ti/Kconfig                    |    4 ++--
 2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt
index 72efaaf..0369e25 100644
--- a/Documentation/devicetree/bindings/net/davinci-mdio.txt
+++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt
@@ -1,8 +1,8 @@
-TI SoC Davinci MDIO Controller Device Tree Bindings
+TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings
 ---------------------------------------------------
 
 Required properties:
-- compatible		: Should be "ti,davinci_mdio"
+- compatible		: Should be "ti,davinci_mdio" or "ti,keystone_mdio"
 - reg			: physical base address and size of the davinci mdio
 			  registers map
 - bus_freq		: Mdio Bus frequency
@@ -19,7 +19,7 @@ file.
 Examples:
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		reg = <0x4A101000 0x1000>;
 		bus_freq = <1000000>;
 	};
@@ -27,7 +27,7 @@ Examples:
 (or)
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		ti,hwmods = "davinci_mdio";
 		bus_freq = <1000000>;
 	};
diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
index 53150c2..1769700 100644
--- a/drivers/net/ethernet/ti/Kconfig
+++ b/drivers/net/ethernet/ti/Kconfig
@@ -5,7 +5,7 @@
 config NET_VENDOR_TI
 	bool "Texas Instruments (TI) devices"
 	default y
-	depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX))
+	depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE))
 	---help---
 	  If you have a network (Ethernet) card belonging to this class, say Y
 	  and read the Ethernet-HOWTO, available from
@@ -32,7 +32,7 @@ config TI_DAVINCI_EMAC
 
 config TI_DAVINCI_MDIO
 	tristate "TI DaVinci MDIO Support"
-	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX )
+	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE )
 	select PHYLIB
 	---help---
 	  This driver supports TI's DaVinci MDIO module.
-- 
1.7.9.5

[PATCH v2 1/2] net: davinci_mdio: reuse for keystone2 arch

[Grygorii Strashko]

The similar MDIO HW blocks is used by keystone 2 SoCs as
in Davinci SoCs:
- one in Gigabit Ethernet (GbE) Switch Subsystem
  See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
- one in 10 Gigabit Ethernet Subsystem
  See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf

Hence, reuse Davinci MDIO driver for Keystone 2 and
enable TI networking for Keystone 2 devices

Reviewed-by: Santosh Shilimkar <santosh.shilimkar-l0cyMroinI0@public.gmane.org>
Acked-by: Mugunthan V N <mugunthanvnm-l0cyMroinI0@public.gmane.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko-l0cyMroinI0@public.gmane.org>
---
 .../devicetree/bindings/net/davinci-mdio.txt       |    8 ++++----
 drivers/net/ethernet/ti/Kconfig                    |    4 ++--
 2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt
index 72efaaf..0369e25 100644
--- a/Documentation/devicetree/bindings/net/davinci-mdio.txt
+++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt
@@ -1,8 +1,8 @@
-TI SoC Davinci MDIO Controller Device Tree Bindings
+TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings
 ---------------------------------------------------
 
 Required properties:
-- compatible		: Should be "ti,davinci_mdio"
+- compatible		: Should be "ti,davinci_mdio" or "ti,keystone_mdio"
 - reg			: physical base address and size of the davinci mdio
 			  registers map
 - bus_freq		: Mdio Bus frequency
@@ -19,7 +19,7 @@ file.
 Examples:
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		reg = <0x4A101000 0x1000>;
 		bus_freq = <1000000>;
 	};
@@ -27,7 +27,7 @@ Examples:
 (or)
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		ti,hwmods = "davinci_mdio";
 		bus_freq = <1000000>;
 	};
diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
index 53150c2..1769700 100644
--- a/drivers/net/ethernet/ti/Kconfig
+++ b/drivers/net/ethernet/ti/Kconfig
@@ -5,7 +5,7 @@
 config NET_VENDOR_TI
 	bool "Texas Instruments (TI) devices"
 	default y
-	depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX))
+	depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE))
 	---help---
 	  If you have a network (Ethernet) card belonging to this class, say Y
 	  and read the Ethernet-HOWTO, available from
@@ -32,7 +32,7 @@ config TI_DAVINCI_EMAC
 
 config TI_DAVINCI_MDIO
 	tristate "TI DaVinci MDIO Support"
-	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX )
+	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE )
 	select PHYLIB
 	---help---
 	  This driver supports TI's DaVinci MDIO module.
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 1/2] net: davinci_mdio: reuse for keystone2 arch

[Grygorii Strashko]

The similar MDIO HW blocks is used by keystone 2 SoCs as
in Davinci SoCs:
- one in Gigabit Ethernet (GbE) Switch Subsystem
  See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
- one in 10 Gigabit Ethernet Subsystem
  See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf

Hence, reuse Davinci MDIO driver for Keystone 2 and
enable TI networking for Keystone 2 devices

Reviewed-by: Santosh Shilimkar <santosh.shilimkar-l0cyMroinI0@public.gmane.org>
Acked-by: Mugunthan V N <mugunthanvnm-l0cyMroinI0@public.gmane.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko-l0cyMroinI0@public.gmane.org>
---
 .../devicetree/bindings/net/davinci-mdio.txt       |    8 ++++----
 drivers/net/ethernet/ti/Kconfig                    |    4 ++--
 2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt
index 72efaaf..0369e25 100644
--- a/Documentation/devicetree/bindings/net/davinci-mdio.txt
+++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt
@@ -1,8 +1,8 @@
-TI SoC Davinci MDIO Controller Device Tree Bindings
+TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings
 ---------------------------------------------------
 
 Required properties:
-- compatible		: Should be "ti,davinci_mdio"
+- compatible		: Should be "ti,davinci_mdio" or "ti,keystone_mdio"
 - reg			: physical base address and size of the davinci mdio
 			  registers map
 - bus_freq		: Mdio Bus frequency
@@ -19,7 +19,7 @@ file.
 Examples:
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		reg = <0x4A101000 0x1000>;
 		bus_freq = <1000000>;
 	};
@@ -27,7 +27,7 @@ Examples:
 (or)
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		ti,hwmods = "davinci_mdio";
 		bus_freq = <1000000>;
 	};
diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
index 53150c2..1769700 100644
--- a/drivers/net/ethernet/ti/Kconfig
+++ b/drivers/net/ethernet/ti/Kconfig
@@ -5,7 +5,7 @@
 config NET_VENDOR_TI
 	bool "Texas Instruments (TI) devices"
 	default y
-	depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX))
+	depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE))
 	---help---
 	  If you have a network (Ethernet) card belonging to this class, say Y
 	  and read the Ethernet-HOWTO, available from
@@ -32,7 +32,7 @@ config TI_DAVINCI_EMAC
 
 config TI_DAVINCI_MDIO
 	tristate "TI DaVinci MDIO Support"
-	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX )
+	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE )
 	select PHYLIB
 	---help---
 	  This driver supports TI's DaVinci MDIO module.
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 2/2] net: davinci_mdio: allow to create phys from dt

[Grygorii Strashko]

This patch allows to create PHYs from DT in case
if they are explicitly defined. The of_mdiobus_register() is
used for such purposes.

For backward compatibility, call  of_mdiobus_register() only in case
if at least one PHY's child is defined in DT, otherwise rollback to
mdiobus_register().

Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
Hi Santosh,

I haven't changed style for long-comments, because Networking subsystem
requires first line of comment not to be empty:
WARNING:NETWORKING_BLOCK_COMMENT_STYLE: networking block comments don't use an empty /* line, use /* Comment...

 drivers/net/ethernet/ti/davinci_mdio.c |   21 +++++++++++++++++++--
 1 file changed, 19 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/ti/davinci_mdio.c b/drivers/net/ethernet/ti/davinci_mdio.c
index 735dc53..2791f6f 100644
--- a/drivers/net/ethernet/ti/davinci_mdio.c
+++ b/drivers/net/ethernet/ti/davinci_mdio.c
@@ -38,6 +38,7 @@
 #include <linux/davinci_emac.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_mdio.h>
 #include <linux/pinctrl/consumer.h>
 
 /*
@@ -95,6 +96,10 @@ struct davinci_mdio_data {
 	struct mii_bus	*bus;
 	bool		suspended;
 	unsigned long	access_time; /* jiffies */
+	/* Indicates that driver shouldn't modify phy_mask in case
+	 * if MDIO bus is registered from DT.
+	 */
+	bool		skip_scan;
 };
 
 static void __davinci_mdio_reset(struct davinci_mdio_data *data)
@@ -144,6 +149,9 @@ static int davinci_mdio_reset(struct mii_bus *bus)
 	dev_info(data->dev, "davinci mdio revision %d.%d\n",
 		 (ver >> 8) & 0xff, ver & 0xff);
 
+	if (data->skip_scan)
+		return 0;
+
 	/* get phy mask from the alive register */
 	phy_mask = __raw_readl(&data->regs->alive);
 	if (phy_mask) {
@@ -369,8 +377,17 @@ static int davinci_mdio_probe(struct platform_device *pdev)
 		goto bail_out;
 	}
 
-	/* register the mii bus */
-	ret = mdiobus_register(data->bus);
+	/* register the mii bus
+	 * Create PHYs from DT only in case if PHY child nodes are explicitly
+	 * defined to support backward compatibility with DTs which assume that
+	 * Davinci MDIO will always scan the bus for PHYs detection.
+	 */
+	if (dev->of_node && of_get_child_count(dev->of_node)) {
+		data->skip_scan = true;
+		ret = of_mdiobus_register(data->bus, dev->of_node);
+	} else {
+		ret = mdiobus_register(data->bus);
+	}
 	if (ret)
 		goto bail_out;
 
-- 
1.7.9.5

[PATCH v2 2/2] net: davinci_mdio: allow to create phys from dt

[Grygorii Strashko]

This patch allows to create PHYs from DT in case
if they are explicitly defined. The of_mdiobus_register() is
used for such purposes.

For backward compatibility, call  of_mdiobus_register() only in case
if at least one PHY's child is defined in DT, otherwise rollback to
mdiobus_register().

Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
Hi Santosh,

I haven't changed style for long-comments, because Networking subsystem
requires first line of comment not to be empty:
WARNING:NETWORKING_BLOCK_COMMENT_STYLE: networking block comments don't use an empty /* line, use /* Comment...

 drivers/net/ethernet/ti/davinci_mdio.c |   21 +++++++++++++++++++--
 1 file changed, 19 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/ti/davinci_mdio.c b/drivers/net/ethernet/ti/davinci_mdio.c
index 735dc53..2791f6f 100644
--- a/drivers/net/ethernet/ti/davinci_mdio.c
+++ b/drivers/net/ethernet/ti/davinci_mdio.c
@@ -38,6 +38,7 @@
 #include <linux/davinci_emac.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_mdio.h>
 #include <linux/pinctrl/consumer.h>
 
 /*
@@ -95,6 +96,10 @@ struct davinci_mdio_data {
 	struct mii_bus	*bus;
 	bool		suspended;
 	unsigned long	access_time; /* jiffies */
+	/* Indicates that driver shouldn't modify phy_mask in case
+	 * if MDIO bus is registered from DT.
+	 */
+	bool		skip_scan;
 };
 
 static void __davinci_mdio_reset(struct davinci_mdio_data *data)
@@ -144,6 +149,9 @@ static int davinci_mdio_reset(struct mii_bus *bus)
 	dev_info(data->dev, "davinci mdio revision %d.%d\n",
 		 (ver >> 8) & 0xff, ver & 0xff);
 
+	if (data->skip_scan)
+		return 0;
+
 	/* get phy mask from the alive register */
 	phy_mask = __raw_readl(&data->regs->alive);
 	if (phy_mask) {
@@ -369,8 +377,17 @@ static int davinci_mdio_probe(struct platform_device *pdev)
 		goto bail_out;
 	}
 
-	/* register the mii bus */
-	ret = mdiobus_register(data->bus);
+	/* register the mii bus
+	 * Create PHYs from DT only in case if PHY child nodes are explicitly
+	 * defined to support backward compatibility with DTs which assume that
+	 * Davinci MDIO will always scan the bus for PHYs detection.
+	 */
+	if (dev->of_node && of_get_child_count(dev->of_node)) {
+		data->skip_scan = true;
+		ret = of_mdiobus_register(data->bus, dev->of_node);
+	} else {
+		ret = mdiobus_register(data->bus);
+	}
 	if (ret)
 		goto bail_out;
 
-- 
1.7.9.5

Re: [PATCH v2 1/2] net: davinci_mdio: reuse for keystone2 arch

[Prabhakar Lad]

On Wed, Jul 16, 2014 at 1:13 PM, Grygorii Strashko
<grygorii.strashko@ti.com> wrote:
> The similar MDIO HW blocks is used by keystone 2 SoCs as
> in Davinci SoCs:
> - one in Gigabit Ethernet (GbE) Switch Subsystem
>   See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
> - one in 10 Gigabit Ethernet Subsystem
>   See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf
>
> Hence, reuse Davinci MDIO driver for Keystone 2 and
> enable TI networking for Keystone 2 devices
>
> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
> Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>

Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>

Thanks,
--Prabhakar Lad

> ---
>  .../devicetree/bindings/net/davinci-mdio.txt       |    8 ++++----
>  drivers/net/ethernet/ti/Kconfig                    |    4 ++--
>  2 files changed, 6 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt
> index 72efaaf..0369e25 100644
> --- a/Documentation/devicetree/bindings/net/davinci-mdio.txt
> +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt
> @@ -1,8 +1,8 @@
> -TI SoC Davinci MDIO Controller Device Tree Bindings
> +TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings
>  ---------------------------------------------------
>
>  Required properties:
> -- compatible           : Should be "ti,davinci_mdio"
> +- compatible           : Should be "ti,davinci_mdio" or "ti,keystone_mdio"
>  - reg                  : physical base address and size of the davinci mdio
>                           registers map
>  - bus_freq             : Mdio Bus frequency
> @@ -19,7 +19,7 @@ file.
>  Examples:
>
>         mdio: davinci_mdio@4A101000 {
> -               compatible = "ti,cpsw";
> +               compatible = "ti,davinci_mdio";
>                 reg = <0x4A101000 0x1000>;
>                 bus_freq = <1000000>;
>         };
> @@ -27,7 +27,7 @@ Examples:
>  (or)
>
>         mdio: davinci_mdio@4A101000 {
> -               compatible = "ti,cpsw";
> +               compatible = "ti,davinci_mdio";
>                 ti,hwmods = "davinci_mdio";
>                 bus_freq = <1000000>;
>         };
> diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
> index 53150c2..1769700 100644
> --- a/drivers/net/ethernet/ti/Kconfig
> +++ b/drivers/net/ethernet/ti/Kconfig
> @@ -5,7 +5,7 @@
>  config NET_VENDOR_TI
>         bool "Texas Instruments (TI) devices"
>         default y
> -       depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX))
> +       depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE))
>         ---help---
>           If you have a network (Ethernet) card belonging to this class, say Y
>           and read the Ethernet-HOWTO, available from
> @@ -32,7 +32,7 @@ config TI_DAVINCI_EMAC
>
>  config TI_DAVINCI_MDIO
>         tristate "TI DaVinci MDIO Support"
> -       depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX )
> +       depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE )
>         select PHYLIB
>         ---help---
>           This driver supports TI's DaVinci MDIO module.
> --
> 1.7.9.5
>

Re: [PATCH v2 1/2] net: davinci_mdio: reuse for keystone2 arch

[Prabhakar Lad]

On Wed, Jul 16, 2014 at 1:13 PM, Grygorii Strashko
<grygorii.strashko-l0cyMroinI0@public.gmane.org> wrote:
> The similar MDIO HW blocks is used by keystone 2 SoCs as
> in Davinci SoCs:
> - one in Gigabit Ethernet (GbE) Switch Subsystem
>   See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
> - one in 10 Gigabit Ethernet Subsystem
>   See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf
>
> Hence, reuse Davinci MDIO driver for Keystone 2 and
> enable TI networking for Keystone 2 devices
>
> Reviewed-by: Santosh Shilimkar <santosh.shilimkar-l0cyMroinI0@public.gmane.org>
> Acked-by: Mugunthan V N <mugunthanvnm-l0cyMroinI0@public.gmane.org>
> Signed-off-by: Grygorii Strashko <grygorii.strashko-l0cyMroinI0@public.gmane.org>

Reviewed-by: Lad, Prabhakar <prabhakar.csengg-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Thanks,
--Prabhakar Lad

> ---
>  .../devicetree/bindings/net/davinci-mdio.txt       |    8 ++++----
>  drivers/net/ethernet/ti/Kconfig                    |    4 ++--
>  2 files changed, 6 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt
> index 72efaaf..0369e25 100644
> --- a/Documentation/devicetree/bindings/net/davinci-mdio.txt
> +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt
> @@ -1,8 +1,8 @@
> -TI SoC Davinci MDIO Controller Device Tree Bindings
> +TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings
>  ---------------------------------------------------
>
>  Required properties:
> -- compatible           : Should be "ti,davinci_mdio"
> +- compatible           : Should be "ti,davinci_mdio" or "ti,keystone_mdio"
>  - reg                  : physical base address and size of the davinci mdio
>                           registers map
>  - bus_freq             : Mdio Bus frequency
> @@ -19,7 +19,7 @@ file.
>  Examples:
>
>         mdio: davinci_mdio@4A101000 {
> -               compatible = "ti,cpsw";
> +               compatible = "ti,davinci_mdio";
>                 reg = <0x4A101000 0x1000>;
>                 bus_freq = <1000000>;
>         };
> @@ -27,7 +27,7 @@ Examples:
>  (or)
>
>         mdio: davinci_mdio@4A101000 {
> -               compatible = "ti,cpsw";
> +               compatible = "ti,davinci_mdio";
>                 ti,hwmods = "davinci_mdio";
>                 bus_freq = <1000000>;
>         };
> diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
> index 53150c2..1769700 100644
> --- a/drivers/net/ethernet/ti/Kconfig
> +++ b/drivers/net/ethernet/ti/Kconfig
> @@ -5,7 +5,7 @@
>  config NET_VENDOR_TI
>         bool "Texas Instruments (TI) devices"
>         default y
> -       depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX))
> +       depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE))
>         ---help---
>           If you have a network (Ethernet) card belonging to this class, say Y
>           and read the Ethernet-HOWTO, available from
> @@ -32,7 +32,7 @@ config TI_DAVINCI_EMAC
>
>  config TI_DAVINCI_MDIO
>         tristate "TI DaVinci MDIO Support"
> -       depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX )
> +       depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE )
>         select PHYLIB
>         ---help---
>           This driver supports TI's DaVinci MDIO module.
> --
> 1.7.9.5
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 2/2] net: davinci_mdio: allow to create phys from dt

[Prabhakar Lad]

On Wed, Jul 16, 2014 at 1:13 PM, Grygorii Strashko
<grygorii.strashko@ti.com> wrote:
> This patch allows to create PHYs from DT in case
> if they are explicitly defined. The of_mdiobus_register() is
> used for such purposes.
>
> For backward compatibility, call  of_mdiobus_register() only in case
> if at least one PHY's child is defined in DT, otherwise rollback to
> mdiobus_register().
>
> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
> Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>

Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>

Thanks,
--Prabhakar Lad

> ---
> Hi Santosh,
>
> I haven't changed style for long-comments, because Networking subsystem
> requires first line of comment not to be empty:
> WARNING:NETWORKING_BLOCK_COMMENT_STYLE: networking block comments don't use an empty /* line, use /* Comment...
>
>  drivers/net/ethernet/ti/davinci_mdio.c |   21 +++++++++++++++++++--
>  1 file changed, 19 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/net/ethernet/ti/davinci_mdio.c b/drivers/net/ethernet/ti/davinci_mdio.c
> index 735dc53..2791f6f 100644
> --- a/drivers/net/ethernet/ti/davinci_mdio.c
> +++ b/drivers/net/ethernet/ti/davinci_mdio.c
> @@ -38,6 +38,7 @@
>  #include <linux/davinci_emac.h>
>  #include <linux/of.h>
>  #include <linux/of_device.h>
> +#include <linux/of_mdio.h>
>  #include <linux/pinctrl/consumer.h>
>
>  /*
> @@ -95,6 +96,10 @@ struct davinci_mdio_data {
>         struct mii_bus  *bus;
>         bool            suspended;
>         unsigned long   access_time; /* jiffies */
> +       /* Indicates that driver shouldn't modify phy_mask in case
> +        * if MDIO bus is registered from DT.
> +        */
> +       bool            skip_scan;
>  };
>
>  static void __davinci_mdio_reset(struct davinci_mdio_data *data)
> @@ -144,6 +149,9 @@ static int davinci_mdio_reset(struct mii_bus *bus)
>         dev_info(data->dev, "davinci mdio revision %d.%d\n",
>                  (ver >> 8) & 0xff, ver & 0xff);
>
> +       if (data->skip_scan)
> +               return 0;
> +
>         /* get phy mask from the alive register */
>         phy_mask = __raw_readl(&data->regs->alive);
>         if (phy_mask) {
> @@ -369,8 +377,17 @@ static int davinci_mdio_probe(struct platform_device *pdev)
>                 goto bail_out;
>         }
>
> -       /* register the mii bus */
> -       ret = mdiobus_register(data->bus);
> +       /* register the mii bus
> +        * Create PHYs from DT only in case if PHY child nodes are explicitly
> +        * defined to support backward compatibility with DTs which assume that
> +        * Davinci MDIO will always scan the bus for PHYs detection.
> +        */
> +       if (dev->of_node && of_get_child_count(dev->of_node)) {
> +               data->skip_scan = true;
> +               ret = of_mdiobus_register(data->bus, dev->of_node);
> +       } else {
> +               ret = mdiobus_register(data->bus);
> +       }
>         if (ret)
>                 goto bail_out;
>
> --
> 1.7.9.5
>

Re: [PATCH v2 2/2] net: davinci_mdio: allow to create phys from dt

[Prabhakar Lad]

On Wed, Jul 16, 2014 at 1:13 PM, Grygorii Strashko
<grygorii.strashko-l0cyMroinI0@public.gmane.org> wrote:
> This patch allows to create PHYs from DT in case
> if they are explicitly defined. The of_mdiobus_register() is
> used for such purposes.
>
> For backward compatibility, call  of_mdiobus_register() only in case
> if at least one PHY's child is defined in DT, otherwise rollback to
> mdiobus_register().
>
> Reviewed-by: Santosh Shilimkar <santosh.shilimkar-l0cyMroinI0@public.gmane.org>
> Acked-by: Mugunthan V N <mugunthanvnm-l0cyMroinI0@public.gmane.org>
> Signed-off-by: Grygorii Strashko <grygorii.strashko-l0cyMroinI0@public.gmane.org>

Reviewed-by: Lad, Prabhakar <prabhakar.csengg-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Thanks,
--Prabhakar Lad

> ---
> Hi Santosh,
>
> I haven't changed style for long-comments, because Networking subsystem
> requires first line of comment not to be empty:
> WARNING:NETWORKING_BLOCK_COMMENT_STYLE: networking block comments don't use an empty /* line, use /* Comment...
>
>  drivers/net/ethernet/ti/davinci_mdio.c |   21 +++++++++++++++++++--
>  1 file changed, 19 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/net/ethernet/ti/davinci_mdio.c b/drivers/net/ethernet/ti/davinci_mdio.c
> index 735dc53..2791f6f 100644
> --- a/drivers/net/ethernet/ti/davinci_mdio.c
> +++ b/drivers/net/ethernet/ti/davinci_mdio.c
> @@ -38,6 +38,7 @@
>  #include <linux/davinci_emac.h>
>  #include <linux/of.h>
>  #include <linux/of_device.h>
> +#include <linux/of_mdio.h>
>  #include <linux/pinctrl/consumer.h>
>
>  /*
> @@ -95,6 +96,10 @@ struct davinci_mdio_data {
>         struct mii_bus  *bus;
>         bool            suspended;
>         unsigned long   access_time; /* jiffies */
> +       /* Indicates that driver shouldn't modify phy_mask in case
> +        * if MDIO bus is registered from DT.
> +        */
> +       bool            skip_scan;
>  };
>
>  static void __davinci_mdio_reset(struct davinci_mdio_data *data)
> @@ -144,6 +149,9 @@ static int davinci_mdio_reset(struct mii_bus *bus)
>         dev_info(data->dev, "davinci mdio revision %d.%d\n",
>                  (ver >> 8) & 0xff, ver & 0xff);
>
> +       if (data->skip_scan)
> +               return 0;
> +
>         /* get phy mask from the alive register */
>         phy_mask = __raw_readl(&data->regs->alive);
>         if (phy_mask) {
> @@ -369,8 +377,17 @@ static int davinci_mdio_probe(struct platform_device *pdev)
>                 goto bail_out;
>         }
>
> -       /* register the mii bus */
> -       ret = mdiobus_register(data->bus);
> +       /* register the mii bus
> +        * Create PHYs from DT only in case if PHY child nodes are explicitly
> +        * defined to support backward compatibility with DTs which assume that
> +        * Davinci MDIO will always scan the bus for PHYs detection.
> +        */
> +       if (dev->of_node && of_get_child_count(dev->of_node)) {
> +               data->skip_scan = true;
> +               ret = of_mdiobus_register(data->bus, dev->of_node);
> +       } else {
> +               ret = mdiobus_register(data->bus);
> +       }
>         if (ret)
>                 goto bail_out;
>
> --
> 1.7.9.5
>

Re: [PATCH v2 0/2] net: davinci_mdio: reuse for keystone2 arch

[David Miller]

From: Grygorii Strashko <grygorii.strashko@ti.com>
Date: Wed, 16 Jul 2014 15:13:01 +0300

> The similar MDIO HW blocks is used by keystone 2 SoCs as
> in Davinci SoCs:
> - one in Gigabit Ethernet (GbE) Switch Subsystem
>   See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
> - one in 10 Gigabit Ethernet Subsystem
>   See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf
> 
> Hence, reuse Davinci MDIO driver for Keystone 2 and
> enable TI networking for Keystone 2 devices.
> 
> Also, as part of this series, enable PHY's creation from DT, because
> Keystone 2 supports DT boot mode only.
> 
> Changes in v2:
> - review comments applied. 
>   Keystone 2 compatibility string changed to "ti,keystone_mdio".

Series applied to net-next, thanks.

Re: [PATCH v2 0/2] net: davinci_mdio: reuse for keystone2 arch

[David Miller]

From: Grygorii Strashko <grygorii.strashko-l0cyMroinI0@public.gmane.org>
Date: Wed, 16 Jul 2014 15:13:01 +0300

> The similar MDIO HW blocks is used by keystone 2 SoCs as
> in Davinci SoCs:
> - one in Gigabit Ethernet (GbE) Switch Subsystem
>   See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
> - one in 10 Gigabit Ethernet Subsystem
>   See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf
> 
> Hence, reuse Davinci MDIO driver for Keystone 2 and
> enable TI networking for Keystone 2 devices.
> 
> Also, as part of this series, enable PHY's creation from DT, because
> Keystone 2 supports DT boot mode only.
> 
> Changes in v2:
> - review comments applied. 
>   Keystone 2 compatibility string changed to "ti,keystone_mdio".

Series applied to net-next, thanks.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html