From: Vasily Khoruzhick <anarsoul@gmail.com> To: Maxime Ripard <maxime.ripard@bootlin.com>, Chen-Yu Tsai <wens@csie.org>, Rob Herring <robh+dt@kernel.org>, Mark Rutland <mark.rutland@arm.com>, Catalin Marinas <catalin.marinas@arm.com>, Will Deacon <will.deacon@arm.com>, linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org Cc: Vasily Khoruzhick <anarsoul@gmail.com>, Icenowy Zheng <icenowy@aosc.xyz> Subject: [PATCH 3/3] arm64: dts: allwinner: add support for Pinebook Date: Thu, 31 May 2018 23:29:01 -0700 [thread overview] Message-ID: <20180601062901.8052-4-anarsoul@gmail.com> (raw) In-Reply-To: <20180601062901.8052-1-anarsoul@gmail.com> From: Icenowy Zheng <icenowy@aosc.xyz> Pinebook is a A64-based laptop produced by Pine64, with the following peripherals: USB: - Two external USB ports (one is directly connected to A64's OTG controller, the other is under a internal hub connected to the host-only controller.) - USB HID keyboard and touchpad connected to the internal hub. - USB UVC camera connected to the internal hub. Power-related: - A DC IN jack connected to AXP803's DCIN pin. - A Li-Polymer battery connected to AXP803's battery pins. Storage: - An eMMC by Foresee on the main board (in the product revision of the main board it's designed to be switchable). - An external MicroSD card slot. Display: - An eDP LCD panel (1366x768) connected via an ANX6345 RGB-eDP bridge. - A mini HDMI port. Misc: - A Hall sensor designed to detect the status of lid, connected to GPIO PL12. - A headphone jack connected to the SoC's internal codec. - A debug UART port muxed with headphone jack. This commit adds basical support for it. [vasily: squashed several commits into one, added simplefb node, added usbphy to ehci0 and ohci0 nodes] Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-a64-pinebook.dts | 285 ++++++++++++++++++ 2 files changed, 286 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 8bebe7da5ed9..a8c6d0c6f2c5 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-nanopi-a64.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-olinuxino.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts new file mode 100644 index 000000000000..d952db217702 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -0,0 +1,285 @@ +/* + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz> + * Copyright (C) 2018 Vasily Khoruzhick <anarsoul@gmail.com> + * + * SPDX-License-Identifier: (GPL-2.0 OR MIT) + */ + +/dts-v1/; + +#include "sun50i-a64.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + model = "Pinebook"; + compatible = "pine64,pinebook", "allwinner,sun50i-a64"; + + aliases { + serial0 = &uart0; + ethernet0 = &rtl8723cs; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 50000 0>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <2>; + enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */ + }; + + chosen { + stdout-path = "serial0:115200n8"; + + framebuffer-lcd { + panel-supply = <®_dc1sw>; + dvdd25-supply = <®_dldo2>; + dvdd12-supply = <®_fldo1>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + lid_switch { + label = "Lid Switch"; + gpios = <&r_pio 0 12 GPIO_ACTIVE_LOW>; /* PL12 */ + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + linux,can-disable; + }; + }; + + reg_vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ + }; +}; + +&ehci0 { + phys = <&usbphy 0>; + phy-names = "usb"; + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_dcdc1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; + cd-inverted; + disable-wp; + bus-width = <4>; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_dldo4>; + vqmmc-supply = <®_eldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + rtl8723cs: wifi@1 { + reg = <1>; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_eldo1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + mmc-hs200-1_8v; + status = "okay"; +}; + +&ohci0 { + phys = <&usbphy 0>; + phy-names = "usb"; + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pin>; + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp803: pmic@3a3 { + compatible = "x-powers,axp803"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +/* The ANX6345 eDP-bridge is on r_i2c. There is no linux (mainline) + * driver for this chip at the moment, the bootloader initializes it. + * However it can be accessed with the i2c-dev driver from user space. + */ +&r_i2c { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&r_i2c_pins_a>; + status = "okay"; +}; + +#include "axp803.dtsi" + +®_aldo1 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vcc-csi"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pl"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pll-avcc"; +}; + +®_dc1sw { + regulator-name = "vcc-lcd"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-cpux"; +}; + +/* DCDC3 is polyphased with DCDC2 */ + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-hdmi"; +}; + +®_dldo2 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-edp"; +}; + +®_dldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avdd-csi"; +}; + +®_dldo4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_eldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "cpvdd"; +}; + +®_eldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vdd-1v8-csi"; +}; + +®_fldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-1v2-hsic"; +}; + +®_fldo2 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_ldo_io0 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-usb"; + status = "okay"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "host"; +}; + +&usbphy { + usb0_vbus-supply = <®_ldo_io0>; + usb1_vbus-supply = <®_ldo_io0>; + status = "okay"; +}; -- 2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: anarsoul@gmail.com (Vasily Khoruzhick) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH 3/3] arm64: dts: allwinner: add support for Pinebook Date: Thu, 31 May 2018 23:29:01 -0700 [thread overview] Message-ID: <20180601062901.8052-4-anarsoul@gmail.com> (raw) In-Reply-To: <20180601062901.8052-1-anarsoul@gmail.com> From: Icenowy Zheng <icenowy@aosc.xyz> Pinebook is a A64-based laptop produced by Pine64, with the following peripherals: USB: - Two external USB ports (one is directly connected to A64's OTG controller, the other is under a internal hub connected to the host-only controller.) - USB HID keyboard and touchpad connected to the internal hub. - USB UVC camera connected to the internal hub. Power-related: - A DC IN jack connected to AXP803's DCIN pin. - A Li-Polymer battery connected to AXP803's battery pins. Storage: - An eMMC by Foresee on the main board (in the product revision of the main board it's designed to be switchable). - An external MicroSD card slot. Display: - An eDP LCD panel (1366x768) connected via an ANX6345 RGB-eDP bridge. - A mini HDMI port. Misc: - A Hall sensor designed to detect the status of lid, connected to GPIO PL12. - A headphone jack connected to the SoC's internal codec. - A debug UART port muxed with headphone jack. This commit adds basical support for it. [vasily: squashed several commits into one, added simplefb node, added usbphy to ehci0 and ohci0 nodes] Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-a64-pinebook.dts | 285 ++++++++++++++++++ 2 files changed, 286 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 8bebe7da5ed9..a8c6d0c6f2c5 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-nanopi-a64.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-olinuxino.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts new file mode 100644 index 000000000000..d952db217702 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -0,0 +1,285 @@ +/* + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz> + * Copyright (C) 2018 Vasily Khoruzhick <anarsoul@gmail.com> + * + * SPDX-License-Identifier: (GPL-2.0 OR MIT) + */ + +/dts-v1/; + +#include "sun50i-a64.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + model = "Pinebook"; + compatible = "pine64,pinebook", "allwinner,sun50i-a64"; + + aliases { + serial0 = &uart0; + ethernet0 = &rtl8723cs; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 50000 0>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <2>; + enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */ + }; + + chosen { + stdout-path = "serial0:115200n8"; + + framebuffer-lcd { + panel-supply = <®_dc1sw>; + dvdd25-supply = <®_dldo2>; + dvdd12-supply = <®_fldo1>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + lid_switch { + label = "Lid Switch"; + gpios = <&r_pio 0 12 GPIO_ACTIVE_LOW>; /* PL12 */ + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + linux,can-disable; + }; + }; + + reg_vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ + }; +}; + +&ehci0 { + phys = <&usbphy 0>; + phy-names = "usb"; + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_dcdc1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; + cd-inverted; + disable-wp; + bus-width = <4>; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_dldo4>; + vqmmc-supply = <®_eldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + rtl8723cs: wifi at 1 { + reg = <1>; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_eldo1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + mmc-hs200-1_8v; + status = "okay"; +}; + +&ohci0 { + phys = <&usbphy 0>; + phy-names = "usb"; + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pin>; + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp803: pmic at 3a3 { + compatible = "x-powers,axp803"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +/* The ANX6345 eDP-bridge is on r_i2c. There is no linux (mainline) + * driver for this chip at the moment, the bootloader initializes it. + * However it can be accessed with the i2c-dev driver from user space. + */ +&r_i2c { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&r_i2c_pins_a>; + status = "okay"; +}; + +#include "axp803.dtsi" + +®_aldo1 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vcc-csi"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pl"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pll-avcc"; +}; + +®_dc1sw { + regulator-name = "vcc-lcd"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-cpux"; +}; + +/* DCDC3 is polyphased with DCDC2 */ + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-hdmi"; +}; + +®_dldo2 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-edp"; +}; + +®_dldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avdd-csi"; +}; + +®_dldo4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_eldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "cpvdd"; +}; + +®_eldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vdd-1v8-csi"; +}; + +®_fldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-1v2-hsic"; +}; + +®_fldo2 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_ldo_io0 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-usb"; + status = "okay"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "host"; +}; + +&usbphy { + usb0_vbus-supply = <®_ldo_io0>; + usb1_vbus-supply = <®_ldo_io0>; + status = "okay"; +}; -- 2.17.1
next prev parent reply other threads:[~2018-06-01 6:29 UTC|newest] Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top 2018-06-01 6:28 [PATCH 0/3] arm64: allwinner: a64: Add initial support for Pinebook Vasily Khoruzhick 2018-06-01 6:28 ` Vasily Khoruzhick 2018-06-01 6:28 ` [PATCH 1/3] arm64: allwinner: a64: add R_I2C controller Vasily Khoruzhick 2018-06-01 6:28 ` Vasily Khoruzhick 2018-06-01 9:16 ` Maxime Ripard 2018-06-01 9:16 ` Maxime Ripard 2018-06-01 17:30 ` Vasily Khoruzhick 2018-06-01 17:30 ` Vasily Khoruzhick 2018-06-04 8:51 ` Maxime Ripard 2018-06-04 8:51 ` Maxime Ripard 2018-06-01 6:29 ` [PATCH 2/3] dts: sunxi: A64: Add PWM controllers Vasily Khoruzhick 2018-06-01 6:29 ` Vasily Khoruzhick 2018-06-01 9:18 ` Maxime Ripard 2018-06-01 9:18 ` Maxime Ripard 2018-06-01 17:31 ` Vasily Khoruzhick 2018-06-01 17:31 ` Vasily Khoruzhick 2018-06-01 6:29 ` Vasily Khoruzhick [this message] 2018-06-01 6:29 ` [PATCH 3/3] arm64: dts: allwinner: add support for Pinebook Vasily Khoruzhick 2018-06-01 9:23 ` Maxime Ripard 2018-06-01 9:23 ` Maxime Ripard 2018-06-01 17:37 ` Vasily Khoruzhick 2018-06-01 17:37 ` Vasily Khoruzhick 2018-06-04 8:49 ` Maxime Ripard 2018-06-04 8:49 ` Maxime Ripard
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20180601062901.8052-4-anarsoul@gmail.com \ --to=anarsoul@gmail.com \ --cc=catalin.marinas@arm.com \ --cc=devicetree@vger.kernel.org \ --cc=icenowy@aosc.xyz \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=mark.rutland@arm.com \ --cc=maxime.ripard@bootlin.com \ --cc=robh+dt@kernel.org \ --cc=wens@csie.org \ --cc=will.deacon@arm.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.