* [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
@ 2022-01-08 3:04 Patrick Venture
2022-01-10 2:17 ` Patrick Venture
2022-01-10 9:35 ` Philippe Mathieu-Daudé
0 siblings, 2 replies; 15+ messages in thread
From: Patrick Venture @ 2022-01-08 3:04 UTC (permalink / raw)
To: thuth, lvivier, pbonzini; +Cc: qemu-devel, Hao Wu, Doug Evans
From: Hao Wu <wuhaotsh@google.com>
SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
interface that reports AMD SoC's Ttcl (normalized temperature),
and resembles a typical 8-pin remote temperature sensor's I2C interface
to BMC.
This patch implements a basic AMD SB-TSI sensor that is
compatible with the open-source data sheet from AMD and Linux
kernel driver.
Reference:
Linux kernel driver:
https://lkml.org/lkml/2020/12/11/968
Register Map:
https://developer.amd.com/wp-content/resources/56255_3_03.PDF
(Chapter 6)
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Doug Evans <dje@google.com>
---
hw/sensor/Kconfig | 4 +
hw/sensor/meson.build | 1 +
hw/sensor/tmp_sbtsi.c | 393 +++++++++++++++++++++++++++++++++++
hw/sensor/trace-events | 5 +
hw/sensor/trace.h | 1 +
meson.build | 1 +
tests/qtest/meson.build | 1 +
tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
8 files changed, 586 insertions(+)
create mode 100644 hw/sensor/tmp_sbtsi.c
create mode 100644 hw/sensor/trace-events
create mode 100644 hw/sensor/trace.h
create mode 100644 tests/qtest/tmp_sbtsi-test.c
diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
index 9c8a049b06..27f6f79c84 100644
--- a/hw/sensor/Kconfig
+++ b/hw/sensor/Kconfig
@@ -21,3 +21,7 @@ config ADM1272
config MAX34451
bool
depends on I2C
+
+config AMDSBTSI
+ bool
+ depends on I2C
diff --git a/hw/sensor/meson.build b/hw/sensor/meson.build
index 059c4ca935..f7b0e645eb 100644
--- a/hw/sensor/meson.build
+++ b/hw/sensor/meson.build
@@ -4,3 +4,4 @@ softmmu_ss.add(when: 'CONFIG_DPS310', if_true: files('dps310.c'))
softmmu_ss.add(when: 'CONFIG_EMC141X', if_true: files('emc141x.c'))
softmmu_ss.add(when: 'CONFIG_ADM1272', if_true: files('adm1272.c'))
softmmu_ss.add(when: 'CONFIG_MAX34451', if_true: files('max34451.c'))
+softmmu_ss.add(when: 'CONFIG_AMDSBTSI', if_true: files('tmp_sbtsi.c'))
diff --git a/hw/sensor/tmp_sbtsi.c b/hw/sensor/tmp_sbtsi.c
new file mode 100644
index 0000000000..b68c7ebf61
--- /dev/null
+++ b/hw/sensor/tmp_sbtsi.c
@@ -0,0 +1,393 @@
+/*
+ * AMD SBI Temperature Sensor Interface (SB-TSI)
+ *
+ * Copyright 2021 Google LLC
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ */
+
+#include "qemu/osdep.h"
+#include "hw/i2c/smbus_slave.h"
+#include "hw/irq.h"
+#include "migration/vmstate.h"
+#include "qapi/error.h"
+#include "qapi/visitor.h"
+#include "qemu/log.h"
+#include "qemu/module.h"
+#include "trace.h"
+
+#define TYPE_SBTSI "sbtsi"
+#define SBTSI(obj) OBJECT_CHECK(SBTSIState, (obj), TYPE_SBTSI)
+
+/**
+ * SBTSIState:
+ * temperatures are in units of 0.125 degrees
+ * @temperature: Temperature
+ * @limit_low: Lowest temperature
+ * @limit_high: Highest temperature
+ * @status: The status register
+ * @config: The config register
+ * @alert_config: The config for alarm_l output.
+ * @addr: The address to read/write for the next cmd.
+ * @alarm: The alarm_l output pin (GPIO)
+ */
+typedef struct SBTSIState {
+ SMBusDevice parent;
+
+ uint32_t temperature;
+ uint32_t limit_low;
+ uint32_t limit_high;
+ uint8_t status;
+ uint8_t config;
+ uint8_t alert_config;
+ uint8_t addr;
+ qemu_irq alarm;
+} SBTSIState;
+
+/*
+ * SB-TSI registers only support SMBus byte data access. "_INT" registers are
+ * the integer part of a temperature value or limit, and "_DEC" registers are
+ * corresponding decimal parts.
+ */
+#define SBTSI_REG_TEMP_INT 0x01 /* RO */
+#define SBTSI_REG_STATUS 0x02 /* RO */
+#define SBTSI_REG_CONFIG 0x03 /* RO */
+#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
+#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
+#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
+#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
+#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
+#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
+#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
+#define SBTSI_REG_MAN 0xFE /* RO */
+#define SBTSI_REG_REV 0xFF /* RO */
+
+#define SBTSI_STATUS_HIGH_ALERT BIT(4)
+#define SBTSI_STATUS_LOW_ALERT BIT(3)
+#define SBTSI_CONFIG_ALERT_MASK BIT(7)
+#define SBTSI_ALARM_EN BIT(0)
+
+#define SBTSI_LIMIT_LOW_DEFAULT (0)
+#define SBTSI_LIMIT_HIGH_DEFAULT (560)
+#define SBTSI_MAN_DEFAULT (0)
+#define SBTSI_REV_DEFAULT (4)
+#define SBTSI_ALARM_L "alarm_l"
+
+/* The temperature we stored are in units of 0.125 degrees. */
+#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
+
+/*
+ * The integer part and decimal of the temperature both 8 bits.
+ * Only the top 3 bits of the decimal parts are used.
+ * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875 degrees.
+ */
+#define SBTSI_TEMP_MAX 255875
+
+/* The integer part of the temperature in terms of 0.125 degrees. */
+static uint8_t get_temp_int(uint32_t temp)
+{
+ return temp >> 3;
+}
+
+/*
+ * The decimal part of the temperature, in terms of 0.125 degrees.
+ * H/W store it in the top 3 bits so we shift it by 5.
+ */
+static uint8_t get_temp_dec(uint32_t temp)
+{
+ return (temp & 0x7) << 5;
+}
+
+/*
+ * Compute the temperature using the integer and decimal part,
+ * in terms of 0.125 degrees. The decimal part are only the top 3 bits
+ * so we shift it by 5 here.
+ */
+static uint32_t compute_temp(uint8_t integer, uint8_t decimal)
+{
+ return (integer << 3) + (decimal >> 5);
+}
+
+/* Compute new temp with new int part of the temperature. */
+static uint32_t compute_temp_int(uint32_t temp, uint8_t integer)
+{
+ return compute_temp(integer, get_temp_dec(temp));
+}
+
+/* Compute new temp with new dec part of the temperature. */
+static uint32_t compute_temp_dec(uint32_t temp, uint8_t decimal)
+{
+ return compute_temp(get_temp_int(temp), decimal);
+}
+
+/* The integer part of the temperature. */
+static void sbtsi_update_status(SBTSIState *s)
+{
+ s->status = 0;
+ if (s->alert_config & SBTSI_ALARM_EN) {
+ if (s->temperature >= s->limit_high) {
+ s->status |= SBTSI_STATUS_HIGH_ALERT;
+ }
+ if (s->temperature <= s->limit_low) {
+ s->status |= SBTSI_STATUS_LOW_ALERT;
+ }
+ }
+}
+
+static void sbtsi_update_alarm(SBTSIState *s)
+{
+ sbtsi_update_status(s);
+ if (s->status != 0 && !(s->config & SBTSI_CONFIG_ALERT_MASK)) {
+ qemu_irq_raise(s->alarm);
+ } else {
+ qemu_irq_lower(s->alarm);
+ }
+}
+
+static uint8_t sbtsi_read_byte(SMBusDevice *d)
+{
+ SBTSIState *s = SBTSI(d);
+ uint8_t data = 0;
+
+ switch (s->addr) {
+ case SBTSI_REG_TEMP_INT:
+ data = get_temp_int(s->temperature);
+ break;
+
+ case SBTSI_REG_TEMP_DEC:
+ data = get_temp_dec(s->temperature);
+ break;
+
+ case SBTSI_REG_TEMP_HIGH_INT:
+ data = get_temp_int(s->limit_high);
+ break;
+
+ case SBTSI_REG_TEMP_LOW_INT:
+ data = get_temp_int(s->limit_low);
+ break;
+
+ case SBTSI_REG_TEMP_HIGH_DEC:
+ data = get_temp_dec(s->limit_high);
+ break;
+
+ case SBTSI_REG_TEMP_LOW_DEC:
+ data = get_temp_dec(s->limit_low);
+ break;
+
+ case SBTSI_REG_CONFIG:
+ case SBTSI_REG_CONFIG_WR:
+ data = s->config;
+ break;
+
+ case SBTSI_REG_STATUS:
+ sbtsi_update_alarm(s);
+ data = s->status;
+ break;
+
+ case SBTSI_REG_ALERT_CONFIG:
+ data = s->alert_config;
+ break;
+
+ case SBTSI_REG_MAN:
+ data = SBTSI_MAN_DEFAULT;
+ break;
+
+ case SBTSI_REG_REV:
+ data = SBTSI_REV_DEFAULT;
+ break;
+
+ default:
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: reading from invalid reg: 0x%02x\n",
+ __func__, s->addr);
+ break;
+ }
+
+ trace_tmp_sbtsi_read_data(s->addr, data);
+ return data;
+}
+
+static void sbtsi_write(SBTSIState *s, uint8_t data)
+{
+ trace_tmp_sbtsi_write_data(s->addr, data);
+ switch (s->addr) {
+ case SBTSI_REG_CONFIG_WR:
+ s->config = data;
+ break;
+
+ case SBTSI_REG_TEMP_HIGH_INT:
+ s->limit_high = compute_temp_int(s->limit_high, data);
+ break;
+
+ case SBTSI_REG_TEMP_LOW_INT:
+ s->limit_low = compute_temp_int(s->limit_low, data);
+ break;
+
+ case SBTSI_REG_TEMP_HIGH_DEC:
+ s->limit_high = compute_temp_dec(s->limit_high, data);
+ break;
+
+ case SBTSI_REG_TEMP_LOW_DEC:
+ s->limit_low = compute_temp_dec(s->limit_low, data);
+ break;
+
+ case SBTSI_REG_ALERT_CONFIG:
+ s->alert_config = data;
+ break;
+
+ case SBTSI_REG_TEMP_INT:
+ case SBTSI_REG_TEMP_DEC:
+ case SBTSI_REG_CONFIG:
+ case SBTSI_REG_STATUS:
+ case SBTSI_REG_MAN:
+ case SBTSI_REG_REV:
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: writing to read only reg: 0x%02x data: 0x%02x\n",
+ __func__, s->addr, data);
+ break;
+
+ default:
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: writing to invalid reg: 0x%02x data: 0x%02x\n",
+ __func__, s->addr, data);
+ break;
+ }
+ sbtsi_update_alarm(s);
+}
+
+static int sbtsi_write_data(SMBusDevice *d, uint8_t *buf, uint8_t len)
+{
+ SBTSIState *s = SBTSI(d);
+
+ if (len == 0) {
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: writing empty data\n", __func__);
+ return -1;
+ }
+
+ s->addr = buf[0];
+ if (len > 1) {
+ sbtsi_write(s, buf[1]);
+ if (len > 2) {
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: extra data at end\n", __func__);
+ }
+ }
+ return 0;
+}
+
+/* Units are millidegrees. */
+static void sbtsi_get_temperature(Object *obj, Visitor *v, const char *name,
+ void *opaque, Error **errp)
+{
+ SBTSIState *s = SBTSI(obj);
+ uint32_t temp = s->temperature * SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
+
+ visit_type_uint32(v, name, &temp, errp);
+}
+
+/* Units are millidegrees. */
+static void sbtsi_set_temperature(Object *obj, Visitor *v, const char *name,
+ void *opaque, Error **errp)
+{
+ SBTSIState *s = SBTSI(obj);
+ uint32_t temp;
+
+ if (!visit_type_uint32(v, name, &temp, errp)) {
+ return;
+ }
+ if (temp > SBTSI_TEMP_MAX) {
+ error_setg(errp, "value %" PRIu32 ".%03" PRIu32 " C is out of range",
+ temp / 1000, temp % 1000);
+ return;
+ }
+
+ s->temperature = temp / SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
+ sbtsi_update_alarm(s);
+}
+
+static int sbtsi_post_load(void *opaque, int version_id)
+{
+ SBTSIState *s = opaque;
+
+ sbtsi_update_alarm(s);
+ return 0;
+}
+
+static const VMStateDescription vmstate_sbtsi = {
+ .name = "SBTSI",
+ .version_id = 0,
+ .minimum_version_id = 0,
+ .post_load = sbtsi_post_load,
+ .fields = (VMStateField[]) {
+ VMSTATE_UINT32(temperature, SBTSIState),
+ VMSTATE_UINT32(limit_low, SBTSIState),
+ VMSTATE_UINT32(limit_high, SBTSIState),
+ VMSTATE_UINT8(config, SBTSIState),
+ VMSTATE_UINT8(status, SBTSIState),
+ VMSTATE_UINT8(addr, SBTSIState),
+ VMSTATE_END_OF_LIST()
+ }
+};
+
+static void sbtsi_enter_reset(Object *obj, ResetType type)
+{
+ SBTSIState *s = SBTSI(obj);
+
+ s->config = 0;
+ s->limit_low = SBTSI_LIMIT_LOW_DEFAULT;
+ s->limit_high = SBTSI_LIMIT_HIGH_DEFAULT;
+}
+
+static void sbtsi_hold_reset(Object *obj)
+{
+ SBTSIState *s = SBTSI(obj);
+
+ qemu_irq_lower(s->alarm);
+}
+
+static void sbtsi_init(Object *obj)
+{
+ SBTSIState *s = SBTSI(obj);
+
+ /* Current temperature in millidegrees. */
+ object_property_add(obj, "temperature", "uint32",
+ sbtsi_get_temperature, sbtsi_set_temperature,
+ NULL, NULL);
+ qdev_init_gpio_out_named(DEVICE(obj), &s->alarm, SBTSI_ALARM_L, 0);
+}
+
+static void sbtsi_class_init(ObjectClass *klass, void *data)
+{
+ ResettableClass *rc = RESETTABLE_CLASS(klass);
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
+
+ dc->desc = "SB-TSI Temperature Sensor";
+ dc->vmsd = &vmstate_sbtsi;
+ k->write_data = sbtsi_write_data;
+ k->receive_byte = sbtsi_read_byte;
+ rc->phases.enter = sbtsi_enter_reset;
+ rc->phases.hold = sbtsi_hold_reset;
+}
+
+static const TypeInfo sbtsi_info = {
+ .name = TYPE_SBTSI,
+ .parent = TYPE_SMBUS_DEVICE,
+ .instance_size = sizeof(SBTSIState),
+ .instance_init = sbtsi_init,
+ .class_init = sbtsi_class_init,
+};
+
+static void sbtsi_register_types(void)
+{
+ type_register_static(&sbtsi_info);
+}
+
+type_init(sbtsi_register_types)
diff --git a/hw/sensor/trace-events b/hw/sensor/trace-events
new file mode 100644
index 0000000000..21ab3809e2
--- /dev/null
+++ b/hw/sensor/trace-events
@@ -0,0 +1,5 @@
+# See docs/devel/tracing.rst for syntax documentation.
+
+# tmp_sbtsi.c
+tmp_sbtsi_write_data(uint8_t addr, uint8_t value) "SBTSI write addr:0x%02x data: 0x%02x"
+tmp_sbtsi_read_data(uint8_t addr, uint8_t value) "SBTSI read addr:0x%02x data: 0x%02x"
diff --git a/hw/sensor/trace.h b/hw/sensor/trace.h
new file mode 100644
index 0000000000..e4721560b0
--- /dev/null
+++ b/hw/sensor/trace.h
@@ -0,0 +1 @@
+#include "trace/trace-hw_sensor.h"
diff --git a/meson.build b/meson.build
index 53065e96ec..f8ab0bf74e 100644
--- a/meson.build
+++ b/meson.build
@@ -2494,6 +2494,7 @@ if have_system
'hw/rtc',
'hw/s390x',
'hw/scsi',
+ 'hw/sensor',
'hw/sd',
'hw/sh4',
'hw/sparc',
diff --git a/tests/qtest/meson.build b/tests/qtest/meson.build
index 37e1eaa449..d1a8c38f74 100644
--- a/tests/qtest/meson.build
+++ b/tests/qtest/meson.build
@@ -254,6 +254,7 @@ qos_test_ss.add(
'spapr-phb-test.c',
'tmp105-test.c',
'emc141x-test.c',
+ 'tmp_sbtsi-test.c',
'usb-hcd-ohci-test.c',
'virtio-test.c',
'virtio-blk-test.c',
diff --git a/tests/qtest/tmp_sbtsi-test.c b/tests/qtest/tmp_sbtsi-test.c
new file mode 100644
index 0000000000..7f5fafacc7
--- /dev/null
+++ b/tests/qtest/tmp_sbtsi-test.c
@@ -0,0 +1,180 @@
+/*
+ * QTests for the SBTSI temperature sensor
+ *
+ * Copyright 2020 Google LLC
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ */
+
+#include "qemu/osdep.h"
+
+#include "libqtest-single.h"
+#include "libqos/qgraph.h"
+#include "libqos/i2c.h"
+#include "qapi/qmp/qdict.h"
+#include "qemu/bitops.h"
+
+#define TEST_ID "sbtsi-test"
+#define TEST_ADDR (0x4c)
+
+/*
+ * SB-TSI registers only support SMBus byte data access. "_INT" registers are
+ * the integer part of a temperature value or limit, and "_DEC" registers are
+ * corresponding decimal parts.
+ */
+#define REG_TEMP_INT 0x01 /* RO */
+#define REG_STATUS 0x02 /* RO */
+#define REG_CONFIG 0x03 /* RO */
+#define REG_TEMP_HIGH_INT 0x07 /* RW */
+#define REG_TEMP_LOW_INT 0x08 /* RW */
+#define REG_CONFIG_WR 0x09 /* RW */
+#define REG_TEMP_DEC 0x10 /* RO */
+#define REG_TEMP_HIGH_DEC 0x13 /* RW */
+#define REG_TEMP_LOW_DEC 0x14 /* RW */
+#define REG_ALERT_CONFIG 0xBF /* RW */
+
+#define STATUS_HIGH_ALERT BIT(4)
+#define STATUS_LOW_ALERT BIT(3)
+#define CONFIG_ALERT_MASK BIT(7)
+#define ALARM_EN BIT(0)
+
+/* The temperature stored are in units of 0.125 degrees. */
+#define TEMP_UNIT_IN_MILLIDEGREE 125
+#define LIMIT_LOW (10500)
+#define LIMIT_HIGH (55125)
+
+static uint32_t qmp_sbtsi_get_temperature(const char *id)
+{
+ QDict *response;
+ int ret;
+
+ response = qmp("{ 'execute': 'qom-get', 'arguments': { 'path': %s, "
+ "'property': 'temperature' } }", id);
+ g_assert(qdict_haskey(response, "return"));
+ ret = (uint32_t)qdict_get_int(response, "return");
+ qobject_unref(response);
+ return ret;
+}
+
+static void qmp_sbtsi_set_temperature(const char *id, uint32_t value)
+{
+ QDict *response;
+
+ response = qmp("{ 'execute': 'qom-set', 'arguments': { 'path': %s, "
+ "'property': 'temperature', 'value': %d } }", id, value);
+ g_assert(qdict_haskey(response, "return"));
+ qobject_unref(response);
+}
+
+/*
+ * Compute the temperature using the integer and decimal part and return
+ * millidegrees. The decimal part are only the top 3 bits so we shift it by
+ * 5 here.
+ */
+static uint32_t regs_to_temp(uint8_t integer, uint8_t decimal)
+{
+ return ((integer << 3) + (decimal >> 5)) * TEMP_UNIT_IN_MILLIDEGREE;
+}
+
+/*
+ * Compute the integer and decimal parts of the temperature in millidegrees.
+ * H/W store the decimal in the top 3 bits so we shift it by 5.
+ */
+static void temp_to_regs(uint32_t temp, uint8_t *integer, uint8_t *decimal)
+{
+ temp /= TEMP_UNIT_IN_MILLIDEGREE;
+ *integer = temp >> 3;
+ *decimal = (temp & 0x7) << 5;
+}
+
+static void tx_rx(void *obj, void *data, QGuestAllocator *alloc)
+{
+ uint16_t value;
+ uint8_t integer, decimal;
+ QI2CDevice *i2cdev = (QI2CDevice *)obj;
+
+ /* Test default values */
+ value = qmp_sbtsi_get_temperature(TEST_ID);
+ g_assert_cmpuint(value, ==, 0);
+
+ integer = i2c_get8(i2cdev, REG_TEMP_INT);
+ decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
+ g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 0);
+
+ /* Test setting temperature */
+ qmp_sbtsi_set_temperature(TEST_ID, 20000);
+ value = qmp_sbtsi_get_temperature(TEST_ID);
+ g_assert_cmpuint(value, ==, 20000);
+
+ integer = i2c_get8(i2cdev, REG_TEMP_INT);
+ decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
+ g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 20000);
+
+ /* Set alert mask in config */
+ i2c_set8(i2cdev, REG_CONFIG_WR, CONFIG_ALERT_MASK);
+ value = i2c_get8(i2cdev, REG_CONFIG);
+ g_assert_cmphex(value, ==, CONFIG_ALERT_MASK);
+ /* Enable alarm_en */
+ i2c_set8(i2cdev, REG_ALERT_CONFIG, ALARM_EN);
+ value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
+ g_assert_cmphex(value, ==, ALARM_EN);
+
+ /* Test setting limits */
+ /* Limit low = 10.500 */
+ temp_to_regs(LIMIT_LOW, &integer, &decimal);
+ i2c_set8(i2cdev, REG_TEMP_LOW_INT, integer);
+ i2c_set8(i2cdev, REG_TEMP_LOW_DEC, decimal);
+ integer = i2c_get8(i2cdev, REG_TEMP_LOW_INT);
+ decimal = i2c_get8(i2cdev, REG_TEMP_LOW_DEC);
+ g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_LOW);
+ /* Limit high = 55.125 */
+ temp_to_regs(LIMIT_HIGH, &integer, &decimal);
+ i2c_set8(i2cdev, REG_TEMP_HIGH_INT, integer);
+ i2c_set8(i2cdev, REG_TEMP_HIGH_DEC, decimal);
+ integer = i2c_get8(i2cdev, REG_TEMP_HIGH_INT);
+ decimal = i2c_get8(i2cdev, REG_TEMP_HIGH_DEC);
+ g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_HIGH);
+ /* No alert is generated. */
+ value = i2c_get8(i2cdev, REG_STATUS);
+ g_assert_cmphex(value, ==, 0);
+
+ /* Test alert for low temperature */
+ qmp_sbtsi_set_temperature(TEST_ID, LIMIT_LOW);
+ value = i2c_get8(i2cdev, REG_STATUS);
+ g_assert_cmphex(value, ==, STATUS_LOW_ALERT);
+
+ /* Test alert for high temperature */
+ qmp_sbtsi_set_temperature(TEST_ID, LIMIT_HIGH);
+ value = i2c_get8(i2cdev, REG_STATUS);
+ g_assert_cmphex(value, ==, STATUS_HIGH_ALERT);
+
+ /* Disable alarm_en */
+ i2c_set8(i2cdev, REG_ALERT_CONFIG, 0);
+ value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
+ g_assert_cmphex(value, ==, 0);
+ /* No alert when alarm_en is false. */
+ value = i2c_get8(i2cdev, REG_STATUS);
+ g_assert_cmphex(value, ==, 0);
+}
+
+static void sbtsi_register_nodes(void)
+{
+ QOSGraphEdgeOptions opts = {
+ .extra_device_opts = "id=" TEST_ID ",address=0x4c"
+ };
+ add_qi2c_address(&opts, &(QI2CAddress) { TEST_ADDR });
+
+ qos_node_create_driver("sbtsi", i2c_device_create);
+ qos_node_consumes("sbtsi", "i2c-bus", &opts);
+
+ qos_add_test("tx-rx", "sbtsi", tx_rx, NULL);
+}
+libqos_init(sbtsi_register_nodes);
--
2.34.1.575.g55b058a8bb-goog
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-08 3:04 [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface Patrick Venture
@ 2022-01-10 2:17 ` Patrick Venture
2022-01-17 14:05 ` Corey Minyard
2022-01-10 9:35 ` Philippe Mathieu-Daudé
1 sibling, 1 reply; 15+ messages in thread
From: Patrick Venture @ 2022-01-10 2:17 UTC (permalink / raw)
To: Thomas Huth, lvivier, Paolo Bonzini, Corey Minyard
Cc: QEMU Developers, Hao Wu, Doug Evans
[-- Attachment #1: Type: text/plain, Size: 22399 bytes --]
On Fri, Jan 7, 2022 at 7:04 PM Patrick Venture <venture@google.com> wrote:
> From: Hao Wu <wuhaotsh@google.com>
>
> SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
> interface that reports AMD SoC's Ttcl (normalized temperature),
> and resembles a typical 8-pin remote temperature sensor's I2C interface
> to BMC.
>
> This patch implements a basic AMD SB-TSI sensor that is
> compatible with the open-source data sheet from AMD and Linux
> kernel driver.
>
> Reference:
> Linux kernel driver:
> https://lkml.org/lkml/2020/12/11/968
> Register Map:
> https://developer.amd.com/wp-content/resources/56255_3_03.PDF
> (Chapter 6)
>
> Signed-off-by: Hao Wu <wuhaotsh@google.com>
> Reviewed-by: Doug Evans <dje@google.com>
> ---
> hw/sensor/Kconfig | 4 +
> hw/sensor/meson.build | 1 +
> hw/sensor/tmp_sbtsi.c | 393 +++++++++++++++++++++++++++++++++++
> hw/sensor/trace-events | 5 +
> hw/sensor/trace.h | 1 +
> meson.build | 1 +
> tests/qtest/meson.build | 1 +
> tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
> 8 files changed, 586 insertions(+)
> create mode 100644 hw/sensor/tmp_sbtsi.c
> create mode 100644 hw/sensor/trace-events
> create mode 100644 hw/sensor/trace.h
> create mode 100644 tests/qtest/tmp_sbtsi-test.c
>
> diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
> index 9c8a049b06..27f6f79c84 100644
> --- a/hw/sensor/Kconfig
> +++ b/hw/sensor/Kconfig
> @@ -21,3 +21,7 @@ config ADM1272
> config MAX34451
> bool
> depends on I2C
> +
> +config AMDSBTSI
> + bool
> + depends on I2C
> diff --git a/hw/sensor/meson.build b/hw/sensor/meson.build
> index 059c4ca935..f7b0e645eb 100644
> --- a/hw/sensor/meson.build
> +++ b/hw/sensor/meson.build
> @@ -4,3 +4,4 @@ softmmu_ss.add(when: 'CONFIG_DPS310', if_true:
> files('dps310.c'))
> softmmu_ss.add(when: 'CONFIG_EMC141X', if_true: files('emc141x.c'))
> softmmu_ss.add(when: 'CONFIG_ADM1272', if_true: files('adm1272.c'))
> softmmu_ss.add(when: 'CONFIG_MAX34451', if_true: files('max34451.c'))
> +softmmu_ss.add(when: 'CONFIG_AMDSBTSI', if_true: files('tmp_sbtsi.c'))
> diff --git a/hw/sensor/tmp_sbtsi.c b/hw/sensor/tmp_sbtsi.c
> new file mode 100644
> index 0000000000..b68c7ebf61
> --- /dev/null
> +++ b/hw/sensor/tmp_sbtsi.c
> @@ -0,0 +1,393 @@
> +/*
> + * AMD SBI Temperature Sensor Interface (SB-TSI)
> + *
> + * Copyright 2021 Google LLC
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful, but
> WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
> + * for more details.
> + */
> +
> +#include "qemu/osdep.h"
> +#include "hw/i2c/smbus_slave.h"
> +#include "hw/irq.h"
> +#include "migration/vmstate.h"
> +#include "qapi/error.h"
> +#include "qapi/visitor.h"
> +#include "qemu/log.h"
> +#include "qemu/module.h"
> +#include "trace.h"
> +
> +#define TYPE_SBTSI "sbtsi"
> +#define SBTSI(obj) OBJECT_CHECK(SBTSIState, (obj), TYPE_SBTSI)
> +
> +/**
> + * SBTSIState:
> + * temperatures are in units of 0.125 degrees
> + * @temperature: Temperature
> + * @limit_low: Lowest temperature
> + * @limit_high: Highest temperature
> + * @status: The status register
> + * @config: The config register
> + * @alert_config: The config for alarm_l output.
> + * @addr: The address to read/write for the next cmd.
> + * @alarm: The alarm_l output pin (GPIO)
> + */
> +typedef struct SBTSIState {
> + SMBusDevice parent;
> +
> + uint32_t temperature;
> + uint32_t limit_low;
> + uint32_t limit_high;
> + uint8_t status;
> + uint8_t config;
> + uint8_t alert_config;
> + uint8_t addr;
> + qemu_irq alarm;
> +} SBTSIState;
> +
> +/*
> + * SB-TSI registers only support SMBus byte data access. "_INT" registers
> are
> + * the integer part of a temperature value or limit, and "_DEC" registers
> are
> + * corresponding decimal parts.
> + */
> +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
> +#define SBTSI_REG_STATUS 0x02 /* RO */
> +#define SBTSI_REG_CONFIG 0x03 /* RO */
> +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
> +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
> +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
> +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
> +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
> +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
> +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
> +#define SBTSI_REG_MAN 0xFE /* RO */
> +#define SBTSI_REG_REV 0xFF /* RO */
> +
> +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
> +#define SBTSI_STATUS_LOW_ALERT BIT(3)
> +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
> +#define SBTSI_ALARM_EN BIT(0)
> +
> +#define SBTSI_LIMIT_LOW_DEFAULT (0)
> +#define SBTSI_LIMIT_HIGH_DEFAULT (560)
> +#define SBTSI_MAN_DEFAULT (0)
> +#define SBTSI_REV_DEFAULT (4)
> +#define SBTSI_ALARM_L "alarm_l"
> +
> +/* The temperature we stored are in units of 0.125 degrees. */
> +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
> +
> +/*
> + * The integer part and decimal of the temperature both 8 bits.
> + * Only the top 3 bits of the decimal parts are used.
> + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875 degrees.
> + */
> +#define SBTSI_TEMP_MAX 255875
> +
> +/* The integer part of the temperature in terms of 0.125 degrees. */
> +static uint8_t get_temp_int(uint32_t temp)
> +{
> + return temp >> 3;
> +}
> +
> +/*
> + * The decimal part of the temperature, in terms of 0.125 degrees.
> + * H/W store it in the top 3 bits so we shift it by 5.
> + */
> +static uint8_t get_temp_dec(uint32_t temp)
> +{
> + return (temp & 0x7) << 5;
> +}
> +
> +/*
> + * Compute the temperature using the integer and decimal part,
> + * in terms of 0.125 degrees. The decimal part are only the top 3 bits
> + * so we shift it by 5 here.
> + */
> +static uint32_t compute_temp(uint8_t integer, uint8_t decimal)
> +{
> + return (integer << 3) + (decimal >> 5);
> +}
> +
> +/* Compute new temp with new int part of the temperature. */
> +static uint32_t compute_temp_int(uint32_t temp, uint8_t integer)
> +{
> + return compute_temp(integer, get_temp_dec(temp));
> +}
> +
> +/* Compute new temp with new dec part of the temperature. */
> +static uint32_t compute_temp_dec(uint32_t temp, uint8_t decimal)
> +{
> + return compute_temp(get_temp_int(temp), decimal);
> +}
> +
> +/* The integer part of the temperature. */
> +static void sbtsi_update_status(SBTSIState *s)
> +{
> + s->status = 0;
> + if (s->alert_config & SBTSI_ALARM_EN) {
> + if (s->temperature >= s->limit_high) {
> + s->status |= SBTSI_STATUS_HIGH_ALERT;
> + }
> + if (s->temperature <= s->limit_low) {
> + s->status |= SBTSI_STATUS_LOW_ALERT;
> + }
> + }
> +}
> +
> +static void sbtsi_update_alarm(SBTSIState *s)
> +{
> + sbtsi_update_status(s);
> + if (s->status != 0 && !(s->config & SBTSI_CONFIG_ALERT_MASK)) {
> + qemu_irq_raise(s->alarm);
> + } else {
> + qemu_irq_lower(s->alarm);
> + }
> +}
> +
> +static uint8_t sbtsi_read_byte(SMBusDevice *d)
> +{
> + SBTSIState *s = SBTSI(d);
> + uint8_t data = 0;
> +
> + switch (s->addr) {
> + case SBTSI_REG_TEMP_INT:
> + data = get_temp_int(s->temperature);
> + break;
> +
> + case SBTSI_REG_TEMP_DEC:
> + data = get_temp_dec(s->temperature);
> + break;
> +
> + case SBTSI_REG_TEMP_HIGH_INT:
> + data = get_temp_int(s->limit_high);
> + break;
> +
> + case SBTSI_REG_TEMP_LOW_INT:
> + data = get_temp_int(s->limit_low);
> + break;
> +
> + case SBTSI_REG_TEMP_HIGH_DEC:
> + data = get_temp_dec(s->limit_high);
> + break;
> +
> + case SBTSI_REG_TEMP_LOW_DEC:
> + data = get_temp_dec(s->limit_low);
> + break;
> +
> + case SBTSI_REG_CONFIG:
> + case SBTSI_REG_CONFIG_WR:
> + data = s->config;
> + break;
> +
> + case SBTSI_REG_STATUS:
> + sbtsi_update_alarm(s);
> + data = s->status;
> + break;
> +
> + case SBTSI_REG_ALERT_CONFIG:
> + data = s->alert_config;
> + break;
> +
> + case SBTSI_REG_MAN:
> + data = SBTSI_MAN_DEFAULT;
> + break;
> +
> + case SBTSI_REG_REV:
> + data = SBTSI_REV_DEFAULT;
> + break;
> +
> + default:
> + qemu_log_mask(LOG_GUEST_ERROR,
> + "%s: reading from invalid reg: 0x%02x\n",
> + __func__, s->addr);
> + break;
> + }
> +
> + trace_tmp_sbtsi_read_data(s->addr, data);
> + return data;
> +}
> +
> +static void sbtsi_write(SBTSIState *s, uint8_t data)
> +{
> + trace_tmp_sbtsi_write_data(s->addr, data);
> + switch (s->addr) {
> + case SBTSI_REG_CONFIG_WR:
> + s->config = data;
> + break;
> +
> + case SBTSI_REG_TEMP_HIGH_INT:
> + s->limit_high = compute_temp_int(s->limit_high, data);
> + break;
> +
> + case SBTSI_REG_TEMP_LOW_INT:
> + s->limit_low = compute_temp_int(s->limit_low, data);
> + break;
> +
> + case SBTSI_REG_TEMP_HIGH_DEC:
> + s->limit_high = compute_temp_dec(s->limit_high, data);
> + break;
> +
> + case SBTSI_REG_TEMP_LOW_DEC:
> + s->limit_low = compute_temp_dec(s->limit_low, data);
> + break;
> +
> + case SBTSI_REG_ALERT_CONFIG:
> + s->alert_config = data;
> + break;
> +
> + case SBTSI_REG_TEMP_INT:
> + case SBTSI_REG_TEMP_DEC:
> + case SBTSI_REG_CONFIG:
> + case SBTSI_REG_STATUS:
> + case SBTSI_REG_MAN:
> + case SBTSI_REG_REV:
> + qemu_log_mask(LOG_GUEST_ERROR,
> + "%s: writing to read only reg: 0x%02x data: 0x%02x\n",
> + __func__, s->addr, data);
> + break;
> +
> + default:
> + qemu_log_mask(LOG_GUEST_ERROR,
> + "%s: writing to invalid reg: 0x%02x data: 0x%02x\n",
> + __func__, s->addr, data);
> + break;
> + }
> + sbtsi_update_alarm(s);
> +}
> +
> +static int sbtsi_write_data(SMBusDevice *d, uint8_t *buf, uint8_t len)
> +{
> + SBTSIState *s = SBTSI(d);
> +
> + if (len == 0) {
> + qemu_log_mask(LOG_GUEST_ERROR, "%s: writing empty data\n",
> __func__);
> + return -1;
> + }
> +
> + s->addr = buf[0];
> + if (len > 1) {
> + sbtsi_write(s, buf[1]);
> + if (len > 2) {
> + qemu_log_mask(LOG_GUEST_ERROR, "%s: extra data at end\n",
> __func__);
> + }
> + }
> + return 0;
> +}
> +
> +/* Units are millidegrees. */
> +static void sbtsi_get_temperature(Object *obj, Visitor *v, const char
> *name,
> + void *opaque, Error **errp)
> +{
> + SBTSIState *s = SBTSI(obj);
> + uint32_t temp = s->temperature * SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> +
> + visit_type_uint32(v, name, &temp, errp);
> +}
> +
> +/* Units are millidegrees. */
> +static void sbtsi_set_temperature(Object *obj, Visitor *v, const char
> *name,
> + void *opaque, Error **errp)
> +{
> + SBTSIState *s = SBTSI(obj);
> + uint32_t temp;
> +
> + if (!visit_type_uint32(v, name, &temp, errp)) {
> + return;
> + }
> + if (temp > SBTSI_TEMP_MAX) {
> + error_setg(errp, "value %" PRIu32 ".%03" PRIu32 " C is out of
> range",
> + temp / 1000, temp % 1000);
> + return;
> + }
> +
> + s->temperature = temp / SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> + sbtsi_update_alarm(s);
> +}
> +
> +static int sbtsi_post_load(void *opaque, int version_id)
> +{
> + SBTSIState *s = opaque;
> +
> + sbtsi_update_alarm(s);
> + return 0;
> +}
> +
> +static const VMStateDescription vmstate_sbtsi = {
> + .name = "SBTSI",
> + .version_id = 0,
> + .minimum_version_id = 0,
> + .post_load = sbtsi_post_load,
> + .fields = (VMStateField[]) {
> + VMSTATE_UINT32(temperature, SBTSIState),
> + VMSTATE_UINT32(limit_low, SBTSIState),
> + VMSTATE_UINT32(limit_high, SBTSIState),
> + VMSTATE_UINT8(config, SBTSIState),
> + VMSTATE_UINT8(status, SBTSIState),
> + VMSTATE_UINT8(addr, SBTSIState),
> + VMSTATE_END_OF_LIST()
> + }
> +};
> +
> +static void sbtsi_enter_reset(Object *obj, ResetType type)
> +{
> + SBTSIState *s = SBTSI(obj);
> +
> + s->config = 0;
> + s->limit_low = SBTSI_LIMIT_LOW_DEFAULT;
> + s->limit_high = SBTSI_LIMIT_HIGH_DEFAULT;
> +}
> +
> +static void sbtsi_hold_reset(Object *obj)
> +{
> + SBTSIState *s = SBTSI(obj);
> +
> + qemu_irq_lower(s->alarm);
> +}
> +
> +static void sbtsi_init(Object *obj)
> +{
> + SBTSIState *s = SBTSI(obj);
> +
> + /* Current temperature in millidegrees. */
> + object_property_add(obj, "temperature", "uint32",
> + sbtsi_get_temperature, sbtsi_set_temperature,
> + NULL, NULL);
> + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm, SBTSI_ALARM_L, 0);
> +}
> +
> +static void sbtsi_class_init(ObjectClass *klass, void *data)
> +{
> + ResettableClass *rc = RESETTABLE_CLASS(klass);
> + DeviceClass *dc = DEVICE_CLASS(klass);
> + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
> +
> + dc->desc = "SB-TSI Temperature Sensor";
> + dc->vmsd = &vmstate_sbtsi;
> + k->write_data = sbtsi_write_data;
> + k->receive_byte = sbtsi_read_byte;
> + rc->phases.enter = sbtsi_enter_reset;
> + rc->phases.hold = sbtsi_hold_reset;
> +}
> +
> +static const TypeInfo sbtsi_info = {
> + .name = TYPE_SBTSI,
> + .parent = TYPE_SMBUS_DEVICE,
> + .instance_size = sizeof(SBTSIState),
> + .instance_init = sbtsi_init,
> + .class_init = sbtsi_class_init,
> +};
> +
> +static void sbtsi_register_types(void)
> +{
> + type_register_static(&sbtsi_info);
> +}
> +
> +type_init(sbtsi_register_types)
> diff --git a/hw/sensor/trace-events b/hw/sensor/trace-events
> new file mode 100644
> index 0000000000..21ab3809e2
> --- /dev/null
> +++ b/hw/sensor/trace-events
> @@ -0,0 +1,5 @@
> +# See docs/devel/tracing.rst for syntax documentation.
> +
> +# tmp_sbtsi.c
> +tmp_sbtsi_write_data(uint8_t addr, uint8_t value) "SBTSI write
> addr:0x%02x data: 0x%02x"
> +tmp_sbtsi_read_data(uint8_t addr, uint8_t value) "SBTSI read addr:0x%02x
> data: 0x%02x"
> diff --git a/hw/sensor/trace.h b/hw/sensor/trace.h
> new file mode 100644
> index 0000000000..e4721560b0
> --- /dev/null
> +++ b/hw/sensor/trace.h
> @@ -0,0 +1 @@
> +#include "trace/trace-hw_sensor.h"
> diff --git a/meson.build b/meson.build
> index 53065e96ec..f8ab0bf74e 100644
> --- a/meson.build
> +++ b/meson.build
> @@ -2494,6 +2494,7 @@ if have_system
> 'hw/rtc',
> 'hw/s390x',
> 'hw/scsi',
> + 'hw/sensor',
> 'hw/sd',
> 'hw/sh4',
> 'hw/sparc',
> diff --git a/tests/qtest/meson.build b/tests/qtest/meson.build
> index 37e1eaa449..d1a8c38f74 100644
> --- a/tests/qtest/meson.build
> +++ b/tests/qtest/meson.build
> @@ -254,6 +254,7 @@ qos_test_ss.add(
> 'spapr-phb-test.c',
> 'tmp105-test.c',
> 'emc141x-test.c',
> + 'tmp_sbtsi-test.c',
> 'usb-hcd-ohci-test.c',
> 'virtio-test.c',
> 'virtio-blk-test.c',
> diff --git a/tests/qtest/tmp_sbtsi-test.c b/tests/qtest/tmp_sbtsi-test.c
> new file mode 100644
> index 0000000000..7f5fafacc7
> --- /dev/null
> +++ b/tests/qtest/tmp_sbtsi-test.c
> @@ -0,0 +1,180 @@
> +/*
> + * QTests for the SBTSI temperature sensor
> + *
> + * Copyright 2020 Google LLC
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful, but
> WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
> + * for more details.
> + */
> +
> +#include "qemu/osdep.h"
> +
> +#include "libqtest-single.h"
> +#include "libqos/qgraph.h"
> +#include "libqos/i2c.h"
> +#include "qapi/qmp/qdict.h"
> +#include "qemu/bitops.h"
> +
> +#define TEST_ID "sbtsi-test"
> +#define TEST_ADDR (0x4c)
> +
> +/*
> + * SB-TSI registers only support SMBus byte data access. "_INT" registers
> are
> + * the integer part of a temperature value or limit, and "_DEC" registers
> are
> + * corresponding decimal parts.
> + */
> +#define REG_TEMP_INT 0x01 /* RO */
> +#define REG_STATUS 0x02 /* RO */
> +#define REG_CONFIG 0x03 /* RO */
> +#define REG_TEMP_HIGH_INT 0x07 /* RW */
> +#define REG_TEMP_LOW_INT 0x08 /* RW */
> +#define REG_CONFIG_WR 0x09 /* RW */
> +#define REG_TEMP_DEC 0x10 /* RO */
> +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
> +#define REG_TEMP_LOW_DEC 0x14 /* RW */
> +#define REG_ALERT_CONFIG 0xBF /* RW */
> +
> +#define STATUS_HIGH_ALERT BIT(4)
> +#define STATUS_LOW_ALERT BIT(3)
> +#define CONFIG_ALERT_MASK BIT(7)
> +#define ALARM_EN BIT(0)
> +
> +/* The temperature stored are in units of 0.125 degrees. */
> +#define TEMP_UNIT_IN_MILLIDEGREE 125
> +#define LIMIT_LOW (10500)
> +#define LIMIT_HIGH (55125)
> +
> +static uint32_t qmp_sbtsi_get_temperature(const char *id)
> +{
> + QDict *response;
> + int ret;
> +
> + response = qmp("{ 'execute': 'qom-get', 'arguments': { 'path': %s, "
> + "'property': 'temperature' } }", id);
> + g_assert(qdict_haskey(response, "return"));
> + ret = (uint32_t)qdict_get_int(response, "return");
> + qobject_unref(response);
> + return ret;
> +}
> +
> +static void qmp_sbtsi_set_temperature(const char *id, uint32_t value)
> +{
> + QDict *response;
> +
> + response = qmp("{ 'execute': 'qom-set', 'arguments': { 'path': %s, "
> + "'property': 'temperature', 'value': %d } }", id,
> value);
> + g_assert(qdict_haskey(response, "return"));
> + qobject_unref(response);
> +}
> +
> +/*
> + * Compute the temperature using the integer and decimal part and return
> + * millidegrees. The decimal part are only the top 3 bits so we shift it
> by
> + * 5 here.
> + */
> +static uint32_t regs_to_temp(uint8_t integer, uint8_t decimal)
> +{
> + return ((integer << 3) + (decimal >> 5)) * TEMP_UNIT_IN_MILLIDEGREE;
> +}
> +
> +/*
> + * Compute the integer and decimal parts of the temperature in
> millidegrees.
> + * H/W store the decimal in the top 3 bits so we shift it by 5.
> + */
> +static void temp_to_regs(uint32_t temp, uint8_t *integer, uint8_t
> *decimal)
> +{
> + temp /= TEMP_UNIT_IN_MILLIDEGREE;
> + *integer = temp >> 3;
> + *decimal = (temp & 0x7) << 5;
> +}
> +
> +static void tx_rx(void *obj, void *data, QGuestAllocator *alloc)
> +{
> + uint16_t value;
> + uint8_t integer, decimal;
> + QI2CDevice *i2cdev = (QI2CDevice *)obj;
> +
> + /* Test default values */
> + value = qmp_sbtsi_get_temperature(TEST_ID);
> + g_assert_cmpuint(value, ==, 0);
> +
> + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 0);
> +
> + /* Test setting temperature */
> + qmp_sbtsi_set_temperature(TEST_ID, 20000);
> + value = qmp_sbtsi_get_temperature(TEST_ID);
> + g_assert_cmpuint(value, ==, 20000);
> +
> + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 20000);
> +
> + /* Set alert mask in config */
> + i2c_set8(i2cdev, REG_CONFIG_WR, CONFIG_ALERT_MASK);
> + value = i2c_get8(i2cdev, REG_CONFIG);
> + g_assert_cmphex(value, ==, CONFIG_ALERT_MASK);
> + /* Enable alarm_en */
> + i2c_set8(i2cdev, REG_ALERT_CONFIG, ALARM_EN);
> + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> + g_assert_cmphex(value, ==, ALARM_EN);
> +
> + /* Test setting limits */
> + /* Limit low = 10.500 */
> + temp_to_regs(LIMIT_LOW, &integer, &decimal);
> + i2c_set8(i2cdev, REG_TEMP_LOW_INT, integer);
> + i2c_set8(i2cdev, REG_TEMP_LOW_DEC, decimal);
> + integer = i2c_get8(i2cdev, REG_TEMP_LOW_INT);
> + decimal = i2c_get8(i2cdev, REG_TEMP_LOW_DEC);
> + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_LOW);
> + /* Limit high = 55.125 */
> + temp_to_regs(LIMIT_HIGH, &integer, &decimal);
> + i2c_set8(i2cdev, REG_TEMP_HIGH_INT, integer);
> + i2c_set8(i2cdev, REG_TEMP_HIGH_DEC, decimal);
> + integer = i2c_get8(i2cdev, REG_TEMP_HIGH_INT);
> + decimal = i2c_get8(i2cdev, REG_TEMP_HIGH_DEC);
> + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_HIGH);
> + /* No alert is generated. */
> + value = i2c_get8(i2cdev, REG_STATUS);
> + g_assert_cmphex(value, ==, 0);
> +
> + /* Test alert for low temperature */
> + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_LOW);
> + value = i2c_get8(i2cdev, REG_STATUS);
> + g_assert_cmphex(value, ==, STATUS_LOW_ALERT);
> +
> + /* Test alert for high temperature */
> + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_HIGH);
> + value = i2c_get8(i2cdev, REG_STATUS);
> + g_assert_cmphex(value, ==, STATUS_HIGH_ALERT);
> +
> + /* Disable alarm_en */
> + i2c_set8(i2cdev, REG_ALERT_CONFIG, 0);
> + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> + g_assert_cmphex(value, ==, 0);
> + /* No alert when alarm_en is false. */
> + value = i2c_get8(i2cdev, REG_STATUS);
> + g_assert_cmphex(value, ==, 0);
> +}
> +
> +static void sbtsi_register_nodes(void)
> +{
> + QOSGraphEdgeOptions opts = {
> + .extra_device_opts = "id=" TEST_ID ",address=0x4c"
> + };
> + add_qi2c_address(&opts, &(QI2CAddress) { TEST_ADDR });
> +
> + qos_node_create_driver("sbtsi", i2c_device_create);
> + qos_node_consumes("sbtsi", "i2c-bus", &opts);
> +
> + qos_add_test("tx-rx", "sbtsi", tx_rx, NULL);
> +}
> +libqos_init(sbtsi_register_nodes);
> --
+ Corey for i2c maintainer. The new sensor directory is mostly if not
entirely i2c devices. I didn't create a maintainer entry for this i2c
device, but I can if desired and send out a v2.
> 2.34.1.575.g55b058a8bb-goog
>
>
[-- Attachment #2: Type: text/html, Size: 27352 bytes --]
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-08 3:04 [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface Patrick Venture
2022-01-10 2:17 ` Patrick Venture
@ 2022-01-10 9:35 ` Philippe Mathieu-Daudé
2022-01-10 17:14 ` Patrick Venture
2022-01-13 7:19 ` Thomas Huth
1 sibling, 2 replies; 15+ messages in thread
From: Philippe Mathieu-Daudé @ 2022-01-10 9:35 UTC (permalink / raw)
To: Patrick Venture, thuth, lvivier, pbonzini
Cc: Hao Wu, qemu-devel, Corey Minyard, Doug Evans
Hi Patrick,
On 1/8/22 04:04, Patrick Venture wrote:
> From: Hao Wu <wuhaotsh@google.com>
>
> SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
> interface that reports AMD SoC's Ttcl (normalized temperature),
> and resembles a typical 8-pin remote temperature sensor's I2C interface
> to BMC.
>
> This patch implements a basic AMD SB-TSI sensor that is
> compatible with the open-source data sheet from AMD and Linux
> kernel driver.
>
> Reference:
> Linux kernel driver:
> https://lkml.org/lkml/2020/12/11/968
> Register Map:
> https://developer.amd.com/wp-content/resources/56255_3_03.PDF
> (Chapter 6)
>
> Signed-off-by: Hao Wu <wuhaotsh@google.com>
> Reviewed-by: Doug Evans <dje@google.com>
> ---
> hw/sensor/Kconfig | 4 +
> hw/sensor/meson.build | 1 +
> hw/sensor/tmp_sbtsi.c | 393 +++++++++++++++++++++++++++++++++++
> hw/sensor/trace-events | 5 +
> hw/sensor/trace.h | 1 +
> meson.build | 1 +
> tests/qtest/meson.build | 1 +
> tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
Up to Thomas for qtest, but I'd rather split in 2 patches since
different set of maintainers / reviewers.
> +++ b/hw/sensor/tmp_sbtsi.c
> @@ -0,0 +1,393 @@
> +/*
> + * AMD SBI Temperature Sensor Interface (SB-TSI)
> + *
> + * Copyright 2021 Google LLC
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
> + * for more details.
> + */
> +
> +#include "qemu/osdep.h"
> +#include "hw/i2c/smbus_slave.h"
> +#include "hw/irq.h"
> +#include "migration/vmstate.h"
> +#include "qapi/error.h"
> +#include "qapi/visitor.h"
> +#include "qemu/log.h"
> +#include "qemu/module.h"
> +#include "trace.h"
> +
> +#define TYPE_SBTSI "sbtsi"
If you add include/hw/sensor/sbtsi.h, please define the type there, ...
> +/*
> + * SB-TSI registers only support SMBus byte data access. "_INT" registers are
> + * the integer part of a temperature value or limit, and "_DEC" registers are
> + * corresponding decimal parts.
> + */
> +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
> +#define SBTSI_REG_STATUS 0x02 /* RO */
> +#define SBTSI_REG_CONFIG 0x03 /* RO */
> +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
> +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
> +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
> +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
> +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
> +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
> +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
> +#define SBTSI_REG_MAN 0xFE /* RO */
> +#define SBTSI_REG_REV 0xFF /* RO */
> +
> +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
> +#define SBTSI_STATUS_LOW_ALERT BIT(3)
> +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
> +#define SBTSI_ALARM_EN BIT(0)
beside these definitions can be share with qtests.
> +/* The temperature we stored are in units of 0.125 degrees. */
> +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
> +
> +/*
> + * The integer part and decimal of the temperature both 8 bits.
> + * Only the top 3 bits of the decimal parts are used.
> + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875 degrees.
> + */
> +#define SBTSI_TEMP_MAX 255875
Nitpicking, use _IN_MILLIDEGREE suffix?
> +static void sbtsi_init(Object *obj)
> +{
> + SBTSIState *s = SBTSI(obj);
> +
> + /* Current temperature in millidegrees. */
> + object_property_add(obj, "temperature", "uint32",
Can we explicit as "temperature_uC"?
> + sbtsi_get_temperature, sbtsi_set_temperature,
> + NULL, NULL);
> + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm, SBTSI_ALARM_L, 0);
> +}
> +
> +static void sbtsi_class_init(ObjectClass *klass, void *data)
> +{
> + ResettableClass *rc = RESETTABLE_CLASS(klass);
> + DeviceClass *dc = DEVICE_CLASS(klass);
> + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
> +
> + dc->desc = "SB-TSI Temperature Sensor";
> + dc->vmsd = &vmstate_sbtsi;
> + k->write_data = sbtsi_write_data;
> + k->receive_byte = sbtsi_read_byte;
> + rc->phases.enter = sbtsi_enter_reset;
> + rc->phases.hold = sbtsi_hold_reset;
If my previous patch [*] were in, I'd have asked for:
set_bit(DEVICE_CATEGORY_SENSOR, dc->categories);
But since it isn't, I'll keep an eye on which goes in first.
[*] https://www.mail-archive.com/qemu-devel@nongnu.org/msg847088.html
> diff --git a/tests/qtest/tmp_sbtsi-test.c b/tests/qtest/tmp_sbtsi-test.c
> new file mode 100644
> index 0000000000..7f5fafacc7
> --- /dev/null
> +++ b/tests/qtest/tmp_sbtsi-test.c
> @@ -0,0 +1,180 @@
> +/*
> + * QTests for the SBTSI temperature sensor
> + *
> + * Copyright 2020 Google LLC
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
> + * for more details.
> + */
> +
> +#include "qemu/osdep.h"
> +
> +#include "libqtest-single.h"
> +#include "libqos/qgraph.h"
> +#include "libqos/i2c.h"
> +#include "qapi/qmp/qdict.h"
> +#include "qemu/bitops.h"
> +
> +#define TEST_ID "sbtsi-test"
> +#define TEST_ADDR (0x4c)
> +
> +/*
> + * SB-TSI registers only support SMBus byte data access. "_INT" registers are
> + * the integer part of a temperature value or limit, and "_DEC" registers are
> + * corresponding decimal parts.
> + */
> +#define REG_TEMP_INT 0x01 /* RO */
> +#define REG_STATUS 0x02 /* RO */
> +#define REG_CONFIG 0x03 /* RO */
> +#define REG_TEMP_HIGH_INT 0x07 /* RW */
> +#define REG_TEMP_LOW_INT 0x08 /* RW */
> +#define REG_CONFIG_WR 0x09 /* RW */
> +#define REG_TEMP_DEC 0x10 /* RO */
> +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
> +#define REG_TEMP_LOW_DEC 0x14 /* RW */
> +#define REG_ALERT_CONFIG 0xBF /* RW */
> +
> +#define STATUS_HIGH_ALERT BIT(4)
> +#define STATUS_LOW_ALERT BIT(3)
> +#define CONFIG_ALERT_MASK BIT(7)
> +#define ALARM_EN BIT(0)
This is the part that could be shared in "include/hw/sensor/sbtsi.h".
> +/* The temperature stored are in units of 0.125 degrees. */
> +#define TEMP_UNIT_IN_MILLIDEGREE 125
> +#define LIMIT_LOW (10500)
> +#define LIMIT_HIGH (55125)
Nitpicking again, _IN_MILLIDEGREE suffix for coherency?
> +static uint32_t qmp_sbtsi_get_temperature(const char *id)
> +{
> + QDict *response;
> + int ret;
> +
> + response = qmp("{ 'execute': 'qom-get', 'arguments': { 'path': %s, "
> + "'property': 'temperature' } }", id);
If renamed earlier, here 'temperature_uC'.
> + g_assert(qdict_haskey(response, "return"));
> + ret = (uint32_t)qdict_get_int(response, "return");
> + qobject_unref(response);
> + return ret;
> +}
> +
> +static void qmp_sbtsi_set_temperature(const char *id, uint32_t value)
> +{
> + QDict *response;
> +
> + response = qmp("{ 'execute': 'qom-set', 'arguments': { 'path': %s, "
> + "'property': 'temperature', 'value': %d } }", id, value);
> + g_assert(qdict_haskey(response, "return"));
> + qobject_unref(response);
> +}
Thanks,
Phil.
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-10 9:35 ` Philippe Mathieu-Daudé
@ 2022-01-10 17:14 ` Patrick Venture
2022-01-10 19:30 ` Philippe Mathieu-Daudé
2022-01-13 7:19 ` Thomas Huth
1 sibling, 1 reply; 15+ messages in thread
From: Patrick Venture @ 2022-01-10 17:14 UTC (permalink / raw)
To: Philippe Mathieu-Daudé
Cc: Thomas Huth, lvivier, Paolo Bonzini, QEMU Developers, Hao Wu,
Doug Evans, Corey Minyard
[-- Attachment #1: Type: text/plain, Size: 9215 bytes --]
On Mon, Jan 10, 2022 at 1:35 AM Philippe Mathieu-Daudé <f4bug@amsat.org>
wrote:
> Hi Patrick,
>
> On 1/8/22 04:04, Patrick Venture wrote:
> > From: Hao Wu <wuhaotsh@google.com>
> >
> > SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
> > interface that reports AMD SoC's Ttcl (normalized temperature),
> > and resembles a typical 8-pin remote temperature sensor's I2C interface
> > to BMC.
> >
> > This patch implements a basic AMD SB-TSI sensor that is
> > compatible with the open-source data sheet from AMD and Linux
> > kernel driver.
> >
> > Reference:
> > Linux kernel driver:
> > https://lkml.org/lkml/2020/12/11/968
> > Register Map:
> > https://developer.amd.com/wp-content/resources/56255_3_03.PDF
> > (Chapter 6)
> >
> > Signed-off-by: Hao Wu <wuhaotsh@google.com>
> > Reviewed-by: Doug Evans <dje@google.com>
> > ---
> > hw/sensor/Kconfig | 4 +
> > hw/sensor/meson.build | 1 +
> > hw/sensor/tmp_sbtsi.c | 393 +++++++++++++++++++++++++++++++++++
> > hw/sensor/trace-events | 5 +
> > hw/sensor/trace.h | 1 +
> > meson.build | 1 +
>
> > tests/qtest/meson.build | 1 +
> > tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
>
> Up to Thomas for qtest, but I'd rather split in 2 patches since
> different set of maintainers / reviewers.
>
> > +++ b/hw/sensor/tmp_sbtsi.c
> > @@ -0,0 +1,393 @@
> > +/*
> > + * AMD SBI Temperature Sensor Interface (SB-TSI)
> > + *
> > + * Copyright 2021 Google LLC
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> it
> > + * under the terms of the GNU General Public License as published by the
> > + * Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful, but
> WITHOUT
> > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
> > + * for more details.
> > + */
> > +
> > +#include "qemu/osdep.h"
> > +#include "hw/i2c/smbus_slave.h"
> > +#include "hw/irq.h"
> > +#include "migration/vmstate.h"
> > +#include "qapi/error.h"
> > +#include "qapi/visitor.h"
> > +#include "qemu/log.h"
> > +#include "qemu/module.h"
> > +#include "trace.h"
> > +
> > +#define TYPE_SBTSI "sbtsi"
>
> If you add include/hw/sensor/sbtsi.h, please define the type there, ...
>
> > +/*
> > + * SB-TSI registers only support SMBus byte data access. "_INT"
> registers are
> > + * the integer part of a temperature value or limit, and "_DEC"
> registers are
> > + * corresponding decimal parts.
> > + */
> > +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
> > +#define SBTSI_REG_STATUS 0x02 /* RO */
> > +#define SBTSI_REG_CONFIG 0x03 /* RO */
> > +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
> > +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
> > +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
> > +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
> > +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
> > +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
> > +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
> > +#define SBTSI_REG_MAN 0xFE /* RO */
> > +#define SBTSI_REG_REV 0xFF /* RO */
> > +
> > +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
> > +#define SBTSI_STATUS_LOW_ALERT BIT(3)
> > +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
> > +#define SBTSI_ALARM_EN BIT(0)
>
> beside these definitions can be share with qtests.
>
> > +/* The temperature we stored are in units of 0.125 degrees. */
> > +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
> > +
> > +/*
> > + * The integer part and decimal of the temperature both 8 bits.
> > + * Only the top 3 bits of the decimal parts are used.
> > + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875 degrees.
> > + */
> > +#define SBTSI_TEMP_MAX 255875
>
> Nitpicking, use _IN_MILLIDEGREE suffix?
>
I haven't seen this suffix before, is this a style you'd like to start
seeing?
>
> > +static void sbtsi_init(Object *obj)
> > +{
> > + SBTSIState *s = SBTSI(obj);
> > +
> > + /* Current temperature in millidegrees. */
> > + object_property_add(obj, "temperature", "uint32",
>
> Can we explicit as "temperature_uC"?
>
We can, but that's non-standard. As I recall most temperature sensors in
hw/sensors are in millidegrees, but none have unit suffixes.
>
> > + sbtsi_get_temperature, sbtsi_set_temperature,
> > + NULL, NULL);
> > + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm, SBTSI_ALARM_L, 0);
> > +}
> > +
> > +static void sbtsi_class_init(ObjectClass *klass, void *data)
> > +{
> > + ResettableClass *rc = RESETTABLE_CLASS(klass);
> > + DeviceClass *dc = DEVICE_CLASS(klass);
> > + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
> > +
> > + dc->desc = "SB-TSI Temperature Sensor";
> > + dc->vmsd = &vmstate_sbtsi;
> > + k->write_data = sbtsi_write_data;
> > + k->receive_byte = sbtsi_read_byte;
> > + rc->phases.enter = sbtsi_enter_reset;
> > + rc->phases.hold = sbtsi_hold_reset;
>
> If my previous patch [*] were in, I'd have asked for:
>
> set_bit(DEVICE_CATEGORY_SENSOR, dc->categories);
>
> But since it isn't, I'll keep an eye on which goes in first.
>
> [*] https://www.mail-archive.com/qemu-devel@nongnu.org/msg847088.html
>
> > diff --git a/tests/qtest/tmp_sbtsi-test.c b/tests/qtest/tmp_sbtsi-test.c
> > new file mode 100644
> > index 0000000000..7f5fafacc7
> > --- /dev/null
> > +++ b/tests/qtest/tmp_sbtsi-test.c
> > @@ -0,0 +1,180 @@
> > +/*
> > + * QTests for the SBTSI temperature sensor
> > + *
> > + * Copyright 2020 Google LLC
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> it
> > + * under the terms of the GNU General Public License as published by the
> > + * Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful, but
> WITHOUT
> > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
> > + * for more details.
> > + */
> > +
> > +#include "qemu/osdep.h"
> > +
> > +#include "libqtest-single.h"
> > +#include "libqos/qgraph.h"
> > +#include "libqos/i2c.h"
> > +#include "qapi/qmp/qdict.h"
> > +#include "qemu/bitops.h"
> > +
> > +#define TEST_ID "sbtsi-test"
> > +#define TEST_ADDR (0x4c)
> > +
> > +/*
> > + * SB-TSI registers only support SMBus byte data access. "_INT"
> registers are
> > + * the integer part of a temperature value or limit, and "_DEC"
> registers are
> > + * corresponding decimal parts.
> > + */
> > +#define REG_TEMP_INT 0x01 /* RO */
> > +#define REG_STATUS 0x02 /* RO */
> > +#define REG_CONFIG 0x03 /* RO */
> > +#define REG_TEMP_HIGH_INT 0x07 /* RW */
> > +#define REG_TEMP_LOW_INT 0x08 /* RW */
> > +#define REG_CONFIG_WR 0x09 /* RW */
> > +#define REG_TEMP_DEC 0x10 /* RO */
> > +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
> > +#define REG_TEMP_LOW_DEC 0x14 /* RW */
> > +#define REG_ALERT_CONFIG 0xBF /* RW */
> > +
> > +#define STATUS_HIGH_ALERT BIT(4)
> > +#define STATUS_LOW_ALERT BIT(3)
> > +#define CONFIG_ALERT_MASK BIT(7)
> > +#define ALARM_EN BIT(0)
>
> This is the part that could be shared in "include/hw/sensor/sbtsi.h".
>
Ack.
>
> > +/* The temperature stored are in units of 0.125 degrees. */
> > +#define TEMP_UNIT_IN_MILLIDEGREE 125
> > +#define LIMIT_LOW (10500)
> > +#define LIMIT_HIGH (55125)
>
> Nitpicking again, _IN_MILLIDEGREE suffix for coherency?
>
> > +static uint32_t qmp_sbtsi_get_temperature(const char *id)
> > +{
> > + QDict *response;
> > + int ret;
> > +
> > + response = qmp("{ 'execute': 'qom-get', 'arguments': { 'path': %s, "
> > + "'property': 'temperature' } }", id);
>
> If renamed earlier, here 'temperature_uC'.
>
> > + g_assert(qdict_haskey(response, "return"));
> > + ret = (uint32_t)qdict_get_int(response, "return");
> > + qobject_unref(response);
> > + return ret;
> > +}
> > +
> > +static void qmp_sbtsi_set_temperature(const char *id, uint32_t value)
> > +{
> > + QDict *response;
> > +
> > + response = qmp("{ 'execute': 'qom-set', 'arguments': { 'path': %s, "
> > + "'property': 'temperature', 'value': %d } }", id,
> value);
> > + g_assert(qdict_haskey(response, "return"));
> > + qobject_unref(response);
> > +}
>
> Thanks,
>
> Phil.
>
v2 will come with the header split. I can split the qtests into a separate
patch. Was your point because the patches are applied to different staging
trees? Because I would think it ideal to have the qtests and the
corresponding code applied together so that it's easy to know it's
working. If this isn't standard, I can definitely split them.
Patrick
[-- Attachment #2: Type: text/html, Size: 12311 bytes --]
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-10 17:14 ` Patrick Venture
@ 2022-01-10 19:30 ` Philippe Mathieu-Daudé
2022-01-10 19:41 ` Patrick Venture
0 siblings, 1 reply; 15+ messages in thread
From: Philippe Mathieu-Daudé @ 2022-01-10 19:30 UTC (permalink / raw)
To: Patrick Venture
Cc: lvivier, Thomas Huth, Corey Minyard, QEMU Developers, Doug Evans,
Hao Wu, Paolo Bonzini
On 1/10/22 18:14, Patrick Venture wrote:
> On Mon, Jan 10, 2022 at 1:35 AM Philippe Mathieu-Daudé <f4bug@amsat.org
> <mailto:f4bug@amsat.org>> wrote:
>
> Hi Patrick,
>
> On 1/8/22 04:04, Patrick Venture wrote:
> > From: Hao Wu <wuhaotsh@google.com <mailto:wuhaotsh@google.com>>
> >
> > SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
> > interface that reports AMD SoC's Ttcl (normalized temperature),
> > and resembles a typical 8-pin remote temperature sensor's I2C
> interface
> > to BMC.
> >
> > This patch implements a basic AMD SB-TSI sensor that is
> > compatible with the open-source data sheet from AMD and Linux
> > kernel driver.
> >
> > Reference:
> > Linux kernel driver:
> > https://lkml.org/lkml/2020/12/11/968
> <https://lkml.org/lkml/2020/12/11/968>
> > Register Map:
> > https://developer.amd.com/wp-content/resources/56255_3_03.PDF
> <https://developer.amd.com/wp-content/resources/56255_3_03.PDF>
> > (Chapter 6)
> >
> > Signed-off-by: Hao Wu <wuhaotsh@google.com
> <mailto:wuhaotsh@google.com>>
> > Reviewed-by: Doug Evans <dje@google.com <mailto:dje@google.com>>
> > ---
> > hw/sensor/Kconfig | 4 +
> > hw/sensor/meson.build | 1 +
> > hw/sensor/tmp_sbtsi.c | 393
> +++++++++++++++++++++++++++++++++++
> > hw/sensor/trace-events | 5 +
> > hw/sensor/trace.h | 1 +
> > meson.build | 1 +
>
> > tests/qtest/meson.build | 1 +
> > tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
>
> Up to Thomas for qtest, but I'd rather split in 2 patches since
> different set of maintainers / reviewers.
>
> > +++ b/hw/sensor/tmp_sbtsi.c
> > @@ -0,0 +1,393 @@
> > +/*
> > + * AMD SBI Temperature Sensor Interface (SB-TSI)
> > + *
> > + * Copyright 2021 Google LLC
> > + *
> > + * This program is free software; you can redistribute it and/or
> modify it
> > + * under the terms of the GNU General Public License as published
> by the
> > + * Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be
> useful, but WITHOUT
> > + * ANY WARRANTY; without even the implied warranty of
> MERCHANTABILITY or
> > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> License
> > + * for more details.
> > + */
> > +
> > +#include "qemu/osdep.h"
> > +#include "hw/i2c/smbus_slave.h"
> > +#include "hw/irq.h"
> > +#include "migration/vmstate.h"
> > +#include "qapi/error.h"
> > +#include "qapi/visitor.h"
> > +#include "qemu/log.h"
> > +#include "qemu/module.h"
> > +#include "trace.h"
> > +
> > +#define TYPE_SBTSI "sbtsi"
>
> If you add include/hw/sensor/sbtsi.h, please define the type there, ...
>
> > +/*
> > + * SB-TSI registers only support SMBus byte data access. "_INT"
> registers are
> > + * the integer part of a temperature value or limit, and "_DEC"
> registers are
> > + * corresponding decimal parts.
> > + */
> > +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
> > +#define SBTSI_REG_STATUS 0x02 /* RO */
> > +#define SBTSI_REG_CONFIG 0x03 /* RO */
> > +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
> > +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
> > +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
> > +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
> > +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
> > +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
> > +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
> > +#define SBTSI_REG_MAN 0xFE /* RO */
> > +#define SBTSI_REG_REV 0xFF /* RO */
> > +
> > +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
> > +#define SBTSI_STATUS_LOW_ALERT BIT(3)
> > +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
> > +#define SBTSI_ALARM_EN BIT(0)
>
> beside these definitions can be share with qtests.
>
> > +/* The temperature we stored are in units of 0.125 degrees. */
> > +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
> > +
> > +/*
> > + * The integer part and decimal of the temperature both 8 bits.
> > + * Only the top 3 bits of the decimal parts are used.
> > + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875 degrees.
> > + */
> > +#define SBTSI_TEMP_MAX 255875
>
> Nitpicking, use _IN_MILLIDEGREE suffix?
>
>
> I haven't seen this suffix before, is this a style you'd like to start
> seeing?
Well you used it few lines earlier, in the previous definition:
SBTSI_TEMP_UNIT_IN_MILLIDEGREE :)
> > +static void sbtsi_init(Object *obj)
> > +{
> > + SBTSIState *s = SBTSI(obj);
> > +
> > + /* Current temperature in millidegrees. */
> > + object_property_add(obj, "temperature", "uint32",
>
> Can we explicit as "temperature_uC"?
>
>
> We can, but that's non-standard. As I recall most temperature sensors
> in hw/sensors are in millidegrees, but none have unit suffixes.
I tend to agree, but this is not obvious to everybody.
I once started sanitizing / enforcing this but never got there:
https://www.mail-archive.com/qemu-block@nongnu.org/msg65192.html
So I don't mind for your patch, if I keep looking at temp sensors
I'll clean up on top later.
> > + sbtsi_get_temperature, sbtsi_set_temperature,
> > + NULL, NULL);
> > + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm,
> SBTSI_ALARM_L, 0);
> > +}
> > +
> > +static void sbtsi_class_init(ObjectClass *klass, void *data)
> > +{
> > + ResettableClass *rc = RESETTABLE_CLASS(klass);
> > + DeviceClass *dc = DEVICE_CLASS(klass);
> > + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
> > +
> > + dc->desc = "SB-TSI Temperature Sensor";
> > + dc->vmsd = &vmstate_sbtsi;
> > + k->write_data = sbtsi_write_data;
> > + k->receive_byte = sbtsi_read_byte;
> > + rc->phases.enter = sbtsi_enter_reset;
> > + rc->phases.hold = sbtsi_hold_reset;
>
> If my previous patch [*] were in, I'd have asked for:
>
> set_bit(DEVICE_CATEGORY_SENSOR, dc->categories);
>
> But since it isn't, I'll keep an eye on which goes in first.
>
> [*]
> https://www.mail-archive.com/qemu-devel@nongnu.org/msg847088.html
> <https://www.mail-archive.com/qemu-devel@nongnu.org/msg847088.html>
>
> > diff --git a/tests/qtest/tmp_sbtsi-test.c
> b/tests/qtest/tmp_sbtsi-test.c
> > new file mode 100644
> > index 0000000000..7f5fafacc7
> > --- /dev/null
> > +++ b/tests/qtest/tmp_sbtsi-test.c
> > @@ -0,0 +1,180 @@
> > +/*
> > + * QTests for the SBTSI temperature sensor
> > + *
> > + * Copyright 2020 Google LLC
> > + *
> > + * This program is free software; you can redistribute it and/or
> modify it
> > + * under the terms of the GNU General Public License as published
> by the
> > + * Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be
> useful, but WITHOUT
> > + * ANY WARRANTY; without even the implied warranty of
> MERCHANTABILITY or
> > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> License
> > + * for more details.
> > + */
> > +
> > +#include "qemu/osdep.h"
> > +
> > +#include "libqtest-single.h"
> > +#include "libqos/qgraph.h"
> > +#include "libqos/i2c.h"
> > +#include "qapi/qmp/qdict.h"
> > +#include "qemu/bitops.h"
> > +
> > +#define TEST_ID "sbtsi-test"
> > +#define TEST_ADDR (0x4c)
> > +
> > +/*
> > + * SB-TSI registers only support SMBus byte data access. "_INT"
> registers are
> > + * the integer part of a temperature value or limit, and "_DEC"
> registers are
> > + * corresponding decimal parts.
> > + */
> > +#define REG_TEMP_INT 0x01 /* RO */
> > +#define REG_STATUS 0x02 /* RO */
> > +#define REG_CONFIG 0x03 /* RO */
> > +#define REG_TEMP_HIGH_INT 0x07 /* RW */
> > +#define REG_TEMP_LOW_INT 0x08 /* RW */
> > +#define REG_CONFIG_WR 0x09 /* RW */
> > +#define REG_TEMP_DEC 0x10 /* RO */
> > +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
> > +#define REG_TEMP_LOW_DEC 0x14 /* RW */
> > +#define REG_ALERT_CONFIG 0xBF /* RW */
> > +
> > +#define STATUS_HIGH_ALERT BIT(4)
> > +#define STATUS_LOW_ALERT BIT(3)
> > +#define CONFIG_ALERT_MASK BIT(7)
> > +#define ALARM_EN BIT(0)
>
> This is the part that could be shared in "include/hw/sensor/sbtsi.h".
>
>
> Ack.
>
>
>
> > +/* The temperature stored are in units of 0.125 degrees. */
> > +#define TEMP_UNIT_IN_MILLIDEGREE 125
> > +#define LIMIT_LOW (10500)
> > +#define LIMIT_HIGH (55125)
>
> Nitpicking again, _IN_MILLIDEGREE suffix for coherency?
>
> > +static uint32_t qmp_sbtsi_get_temperature(const char *id)
> > +{
> > + QDict *response;
> > + int ret;
> > +
> > + response = qmp("{ 'execute': 'qom-get', 'arguments': {
> 'path': %s, "
> > + "'property': 'temperature' } }", id);
>
> If renamed earlier, here 'temperature_uC'.
>
> > + g_assert(qdict_haskey(response, "return"));
> > + ret = (uint32_t)qdict_get_int(response, "return");
> > + qobject_unref(response);
> > + return ret;
> > +}
> > +
> > +static void qmp_sbtsi_set_temperature(const char *id, uint32_t value)
> > +{
> > + QDict *response;
> > +
> > + response = qmp("{ 'execute': 'qom-set', 'arguments': {
> 'path': %s, "
> > + "'property': 'temperature', 'value': %d } }",
> id, value);
> > + g_assert(qdict_haskey(response, "return"));
> > + qobject_unref(response);
> > +}
>
> Thanks,
>
> Phil.
>
>
> v2 will come with the header split. I can split the qtests into a
> separate patch. Was your point because the patches are applied to
> different staging trees? Because I would think it ideal to have the
> qtests and the corresponding code applied together so that it's easy to
> know it's working. If this isn't standard, I can definitely split them.
If split, both patches certainly should be queued consecutively via the
same tree. I asked the split because I'm OK to give a R-b tag for the
hw/ part, but am not sure about the tests/ part. Possibly others would
be OK to review the qtest but would be unsure about the hw/ part.
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-10 19:30 ` Philippe Mathieu-Daudé
@ 2022-01-10 19:41 ` Patrick Venture
0 siblings, 0 replies; 15+ messages in thread
From: Patrick Venture @ 2022-01-10 19:41 UTC (permalink / raw)
To: Philippe Mathieu-Daudé
Cc: Thomas Huth, lvivier, Paolo Bonzini, QEMU Developers, Hao Wu,
Doug Evans, Corey Minyard
[-- Attachment #1: Type: text/plain, Size: 12197 bytes --]
On Mon, Jan 10, 2022 at 11:30 AM Philippe Mathieu-Daudé <f4bug@amsat.org>
wrote:
> On 1/10/22 18:14, Patrick Venture wrote:
> > On Mon, Jan 10, 2022 at 1:35 AM Philippe Mathieu-Daudé <f4bug@amsat.org
> > <mailto:f4bug@amsat.org>> wrote:
> >
> > Hi Patrick,
> >
> > On 1/8/22 04:04, Patrick Venture wrote:
> > > From: Hao Wu <wuhaotsh@google.com <mailto:wuhaotsh@google.com>>
> > >
> > > SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
> > > interface that reports AMD SoC's Ttcl (normalized temperature),
> > > and resembles a typical 8-pin remote temperature sensor's I2C
> > interface
> > > to BMC.
> > >
> > > This patch implements a basic AMD SB-TSI sensor that is
> > > compatible with the open-source data sheet from AMD and Linux
> > > kernel driver.
> > >
> > > Reference:
> > > Linux kernel driver:
> > > https://lkml.org/lkml/2020/12/11/968
> > <https://lkml.org/lkml/2020/12/11/968>
> > > Register Map:
> > > https://developer.amd.com/wp-content/resources/56255_3_03.PDF
> > <https://developer.amd.com/wp-content/resources/56255_3_03.PDF>
> > > (Chapter 6)
> > >
> > > Signed-off-by: Hao Wu <wuhaotsh@google.com
> > <mailto:wuhaotsh@google.com>>
> > > Reviewed-by: Doug Evans <dje@google.com <mailto:dje@google.com>>
> > > ---
> > > hw/sensor/Kconfig | 4 +
> > > hw/sensor/meson.build | 1 +
> > > hw/sensor/tmp_sbtsi.c | 393
> > +++++++++++++++++++++++++++++++++++
> > > hw/sensor/trace-events | 5 +
> > > hw/sensor/trace.h | 1 +
> > > meson.build | 1 +
> >
> > > tests/qtest/meson.build | 1 +
> > > tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
> >
> > Up to Thomas for qtest, but I'd rather split in 2 patches since
> > different set of maintainers / reviewers.
> >
> > > +++ b/hw/sensor/tmp_sbtsi.c
> > > @@ -0,0 +1,393 @@
> > > +/*
> > > + * AMD SBI Temperature Sensor Interface (SB-TSI)
> > > + *
> > > + * Copyright 2021 Google LLC
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> > modify it
> > > + * under the terms of the GNU General Public License as published
> > by the
> > > + * Free Software Foundation; either version 2 of the License, or
> > > + * (at your option) any later version.
> > > + *
> > > + * This program is distributed in the hope that it will be
> > useful, but WITHOUT
> > > + * ANY WARRANTY; without even the implied warranty of
> > MERCHANTABILITY or
> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> > License
> > > + * for more details.
> > > + */
> > > +
> > > +#include "qemu/osdep.h"
> > > +#include "hw/i2c/smbus_slave.h"
> > > +#include "hw/irq.h"
> > > +#include "migration/vmstate.h"
> > > +#include "qapi/error.h"
> > > +#include "qapi/visitor.h"
> > > +#include "qemu/log.h"
> > > +#include "qemu/module.h"
> > > +#include "trace.h"
> > > +
> > > +#define TYPE_SBTSI "sbtsi"
> >
> > If you add include/hw/sensor/sbtsi.h, please define the type there,
> ...
> >
> > > +/*
> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
> > registers are
> > > + * the integer part of a temperature value or limit, and "_DEC"
> > registers are
> > > + * corresponding decimal parts.
> > > + */
> > > +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
> > > +#define SBTSI_REG_STATUS 0x02 /* RO */
> > > +#define SBTSI_REG_CONFIG 0x03 /* RO */
> > > +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
> > > +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
> > > +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
> > > +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
> > > +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
> > > +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
> > > +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
> > > +#define SBTSI_REG_MAN 0xFE /* RO */
> > > +#define SBTSI_REG_REV 0xFF /* RO */
> > > +
> > > +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
> > > +#define SBTSI_STATUS_LOW_ALERT BIT(3)
> > > +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
> > > +#define SBTSI_ALARM_EN BIT(0)
> >
> > beside these definitions can be share with qtests.
> >
> > > +/* The temperature we stored are in units of 0.125 degrees. */
> > > +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
> > > +
> > > +/*
> > > + * The integer part and decimal of the temperature both 8 bits.
> > > + * Only the top 3 bits of the decimal parts are used.
> > > + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875
> degrees.
> > > + */
> > > +#define SBTSI_TEMP_MAX 255875
> >
> > Nitpicking, use _IN_MILLIDEGREE suffix?
> >
> >
> > I haven't seen this suffix before, is this a style you'd like to start
> > seeing?
>
> Well you used it few lines earlier, in the previous definition:
> SBTSI_TEMP_UNIT_IN_MILLIDEGREE :)
>
Ha, thanks! :) I didn't notice Hao had done that. I'll make it consistent.
>
> > > +static void sbtsi_init(Object *obj)
> > > +{
> > > + SBTSIState *s = SBTSI(obj);
> > > +
> > > + /* Current temperature in millidegrees. */
> > > + object_property_add(obj, "temperature", "uint32",
> >
> > Can we explicit as "temperature_uC"?
> >
> >
> > We can, but that's non-standard. As I recall most temperature sensors
> > in hw/sensors are in millidegrees, but none have unit suffixes.
>
> I tend to agree, but this is not obvious to everybody.
>
> I once started sanitizing / enforcing this but never got there:
> https://www.mail-archive.com/qemu-block@nongnu.org/msg65192.html
>
> So I don't mind for your patch, if I keep looking at temp sensors
> I'll clean up on top later.
>
Thanks, it seems like the type of change that was best as sweeping vs a
one-off.
>
> > > + sbtsi_get_temperature,
> sbtsi_set_temperature,
> > > + NULL, NULL);
> > > + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm,
> > SBTSI_ALARM_L, 0);
> > > +}
> > > +
> > > +static void sbtsi_class_init(ObjectClass *klass, void *data)
> > > +{
> > > + ResettableClass *rc = RESETTABLE_CLASS(klass);
> > > + DeviceClass *dc = DEVICE_CLASS(klass);
> > > + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
> > > +
> > > + dc->desc = "SB-TSI Temperature Sensor";
> > > + dc->vmsd = &vmstate_sbtsi;
> > > + k->write_data = sbtsi_write_data;
> > > + k->receive_byte = sbtsi_read_byte;
> > > + rc->phases.enter = sbtsi_enter_reset;
> > > + rc->phases.hold = sbtsi_hold_reset;
> >
> > If my previous patch [*] were in, I'd have asked for:
> >
> > set_bit(DEVICE_CATEGORY_SENSOR, dc->categories);
> >
> > But since it isn't, I'll keep an eye on which goes in first.
> >
> > [*]
> > https://www.mail-archive.com/qemu-devel@nongnu.org/msg847088.html
> > <https://www.mail-archive.com/qemu-devel@nongnu.org/msg847088.html>
> >
> > > diff --git a/tests/qtest/tmp_sbtsi-test.c
> > b/tests/qtest/tmp_sbtsi-test.c
> > > new file mode 100644
> > > index 0000000000..7f5fafacc7
> > > --- /dev/null
> > > +++ b/tests/qtest/tmp_sbtsi-test.c
> > > @@ -0,0 +1,180 @@
> > > +/*
> > > + * QTests for the SBTSI temperature sensor
> > > + *
> > > + * Copyright 2020 Google LLC
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> > modify it
> > > + * under the terms of the GNU General Public License as published
> > by the
> > > + * Free Software Foundation; either version 2 of the License, or
> > > + * (at your option) any later version.
> > > + *
> > > + * This program is distributed in the hope that it will be
> > useful, but WITHOUT
> > > + * ANY WARRANTY; without even the implied warranty of
> > MERCHANTABILITY or
> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> > License
> > > + * for more details.
> > > + */
> > > +
> > > +#include "qemu/osdep.h"
> > > +
> > > +#include "libqtest-single.h"
> > > +#include "libqos/qgraph.h"
> > > +#include "libqos/i2c.h"
> > > +#include "qapi/qmp/qdict.h"
> > > +#include "qemu/bitops.h"
> > > +
> > > +#define TEST_ID "sbtsi-test"
> > > +#define TEST_ADDR (0x4c)
> > > +
> > > +/*
> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
> > registers are
> > > + * the integer part of a temperature value or limit, and "_DEC"
> > registers are
> > > + * corresponding decimal parts.
> > > + */
> > > +#define REG_TEMP_INT 0x01 /* RO */
> > > +#define REG_STATUS 0x02 /* RO */
> > > +#define REG_CONFIG 0x03 /* RO */
> > > +#define REG_TEMP_HIGH_INT 0x07 /* RW */
> > > +#define REG_TEMP_LOW_INT 0x08 /* RW */
> > > +#define REG_CONFIG_WR 0x09 /* RW */
> > > +#define REG_TEMP_DEC 0x10 /* RO */
> > > +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
> > > +#define REG_TEMP_LOW_DEC 0x14 /* RW */
> > > +#define REG_ALERT_CONFIG 0xBF /* RW */
> > > +
> > > +#define STATUS_HIGH_ALERT BIT(4)
> > > +#define STATUS_LOW_ALERT BIT(3)
> > > +#define CONFIG_ALERT_MASK BIT(7)
> > > +#define ALARM_EN BIT(0)
> >
> > This is the part that could be shared in "include/hw/sensor/sbtsi.h".
> >
> >
> > Ack.
> >
> >
> >
> > > +/* The temperature stored are in units of 0.125 degrees. */
> > > +#define TEMP_UNIT_IN_MILLIDEGREE 125
> > > +#define LIMIT_LOW (10500)
> > > +#define LIMIT_HIGH (55125)
> >
> > Nitpicking again, _IN_MILLIDEGREE suffix for coherency?
> >
> > > +static uint32_t qmp_sbtsi_get_temperature(const char *id)
> > > +{
> > > + QDict *response;
> > > + int ret;
> > > +
> > > + response = qmp("{ 'execute': 'qom-get', 'arguments': {
> > 'path': %s, "
> > > + "'property': 'temperature' } }", id);
> >
> > If renamed earlier, here 'temperature_uC'.
> >
> > > + g_assert(qdict_haskey(response, "return"));
> > > + ret = (uint32_t)qdict_get_int(response, "return");
> > > + qobject_unref(response);
> > > + return ret;
> > > +}
> > > +
> > > +static void qmp_sbtsi_set_temperature(const char *id, uint32_t
> value)
> > > +{
> > > + QDict *response;
> > > +
> > > + response = qmp("{ 'execute': 'qom-set', 'arguments': {
> > 'path': %s, "
> > > + "'property': 'temperature', 'value': %d } }",
> > id, value);
> > > + g_assert(qdict_haskey(response, "return"));
> > > + qobject_unref(response);
> > > +}
> >
> > Thanks,
> >
> > Phil.
> >
> >
> > v2 will come with the header split. I can split the qtests into a
> > separate patch. Was your point because the patches are applied to
> > different staging trees? Because I would think it ideal to have the
> > qtests and the corresponding code applied together so that it's easy to
> > know it's working. If this isn't standard, I can definitely split them.
>
> If split, both patches certainly should be queued consecutively via the
> same tree. I asked the split because I'm OK to give a R-b tag for the
> hw/ part, but am not sure about the tests/ part. Possibly others would
> be OK to review the qtest but would be unsure about the hw/ part.
>
Ok, so split the patches into two commits in the same mailing thing. That
makes sense. I'll set that up for the v2.
[-- Attachment #2: Type: text/html, Size: 17582 bytes --]
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-10 9:35 ` Philippe Mathieu-Daudé
2022-01-10 17:14 ` Patrick Venture
@ 2022-01-13 7:19 ` Thomas Huth
1 sibling, 0 replies; 15+ messages in thread
From: Thomas Huth @ 2022-01-13 7:19 UTC (permalink / raw)
To: Philippe Mathieu-Daudé, Patrick Venture, lvivier, pbonzini
Cc: Hao Wu, qemu-devel, Corey Minyard, Doug Evans
On 10/01/2022 10.35, Philippe Mathieu-Daudé wrote:
> Hi Patrick,
>
> On 1/8/22 04:04, Patrick Venture wrote:
>> From: Hao Wu <wuhaotsh@google.com>
>>
>> SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
>> interface that reports AMD SoC's Ttcl (normalized temperature),
>> and resembles a typical 8-pin remote temperature sensor's I2C interface
>> to BMC.
>>
>> This patch implements a basic AMD SB-TSI sensor that is
>> compatible with the open-source data sheet from AMD and Linux
>> kernel driver.
>>
>> Reference:
>> Linux kernel driver:
>> https://lkml.org/lkml/2020/12/11/968
>> Register Map:
>> https://developer.amd.com/wp-content/resources/56255_3_03.PDF
>> (Chapter 6)
>>
>> Signed-off-by: Hao Wu <wuhaotsh@google.com>
>> Reviewed-by: Doug Evans <dje@google.com>
>> ---
>> hw/sensor/Kconfig | 4 +
>> hw/sensor/meson.build | 1 +
>> hw/sensor/tmp_sbtsi.c | 393 +++++++++++++++++++++++++++++++++++
>> hw/sensor/trace-events | 5 +
>> hw/sensor/trace.h | 1 +
>> meson.build | 1 +
>
>> tests/qtest/meson.build | 1 +
>> tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
>
> Up to Thomas for qtest, but I'd rather split in 2 patches since
> different set of maintainers / reviewers.
I don't mind too much - but anyway, I'd prefer if we could stick to "-" in
file names here - mixing underscores and "-" in file names looks somewhat
weird (I know, there are already some files like this, but I'd prefer if
we'd not extend that list).
Thomas
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-10 2:17 ` Patrick Venture
@ 2022-01-17 14:05 ` Corey Minyard
2022-01-18 17:10 ` Patrick Venture
0 siblings, 1 reply; 15+ messages in thread
From: Corey Minyard @ 2022-01-17 14:05 UTC (permalink / raw)
To: Patrick Venture
Cc: lvivier, Thomas Huth, QEMU Developers, Doug Evans, Hao Wu, Paolo Bonzini
On Sun, Jan 09, 2022 at 06:17:34PM -0800, Patrick Venture wrote:
> On Fri, Jan 7, 2022 at 7:04 PM Patrick Venture <venture@google.com> wrote:
>
> > From: Hao Wu <wuhaotsh@google.com>
> >
> > SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
> > interface that reports AMD SoC's Ttcl (normalized temperature),
> > and resembles a typical 8-pin remote temperature sensor's I2C interface
> > to BMC.
> >
> > This patch implements a basic AMD SB-TSI sensor that is
> > compatible with the open-source data sheet from AMD and Linux
> > kernel driver.
> >
> > Reference:
> > Linux kernel driver:
> > https://lkml.org/lkml/2020/12/11/968
> > Register Map:
> > https://developer.amd.com/wp-content/resources/56255_3_03.PDF
> > (Chapter 6)
> >
> > Signed-off-by: Hao Wu <wuhaotsh@google.com>
> > Reviewed-by: Doug Evans <dje@google.com>
> > ---
> > hw/sensor/Kconfig | 4 +
> > hw/sensor/meson.build | 1 +
> > hw/sensor/tmp_sbtsi.c | 393 +++++++++++++++++++++++++++++++++++
> > hw/sensor/trace-events | 5 +
> > hw/sensor/trace.h | 1 +
> > meson.build | 1 +
> > tests/qtest/meson.build | 1 +
> > tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
> > 8 files changed, 586 insertions(+)
> > create mode 100644 hw/sensor/tmp_sbtsi.c
> > create mode 100644 hw/sensor/trace-events
> > create mode 100644 hw/sensor/trace.h
> > create mode 100644 tests/qtest/tmp_sbtsi-test.c
> >
> > diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
> > index 9c8a049b06..27f6f79c84 100644
> > --- a/hw/sensor/Kconfig
> > +++ b/hw/sensor/Kconfig
> > @@ -21,3 +21,7 @@ config ADM1272
> > config MAX34451
> > bool
> > depends on I2C
> > +
> > +config AMDSBTSI
> > + bool
> > + depends on I2C
> > diff --git a/hw/sensor/meson.build b/hw/sensor/meson.build
> > index 059c4ca935..f7b0e645eb 100644
> > --- a/hw/sensor/meson.build
> > +++ b/hw/sensor/meson.build
> > @@ -4,3 +4,4 @@ softmmu_ss.add(when: 'CONFIG_DPS310', if_true:
> > files('dps310.c'))
> > softmmu_ss.add(when: 'CONFIG_EMC141X', if_true: files('emc141x.c'))
> > softmmu_ss.add(when: 'CONFIG_ADM1272', if_true: files('adm1272.c'))
> > softmmu_ss.add(when: 'CONFIG_MAX34451', if_true: files('max34451.c'))
> > +softmmu_ss.add(when: 'CONFIG_AMDSBTSI', if_true: files('tmp_sbtsi.c'))
> > diff --git a/hw/sensor/tmp_sbtsi.c b/hw/sensor/tmp_sbtsi.c
> > new file mode 100644
> > index 0000000000..b68c7ebf61
> > --- /dev/null
> > +++ b/hw/sensor/tmp_sbtsi.c
> > @@ -0,0 +1,393 @@
> > +/*
> > + * AMD SBI Temperature Sensor Interface (SB-TSI)
> > + *
> > + * Copyright 2021 Google LLC
> > + *
> > + * This program is free software; you can redistribute it and/or modify it
> > + * under the terms of the GNU General Public License as published by the
> > + * Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful, but
> > WITHOUT
> > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
> > + * for more details.
> > + */
> > +
> > +#include "qemu/osdep.h"
> > +#include "hw/i2c/smbus_slave.h"
> > +#include "hw/irq.h"
> > +#include "migration/vmstate.h"
> > +#include "qapi/error.h"
> > +#include "qapi/visitor.h"
> > +#include "qemu/log.h"
> > +#include "qemu/module.h"
> > +#include "trace.h"
> > +
> > +#define TYPE_SBTSI "sbtsi"
> > +#define SBTSI(obj) OBJECT_CHECK(SBTSIState, (obj), TYPE_SBTSI)
> > +
> > +/**
> > + * SBTSIState:
> > + * temperatures are in units of 0.125 degrees
> > + * @temperature: Temperature
> > + * @limit_low: Lowest temperature
> > + * @limit_high: Highest temperature
> > + * @status: The status register
> > + * @config: The config register
> > + * @alert_config: The config for alarm_l output.
> > + * @addr: The address to read/write for the next cmd.
> > + * @alarm: The alarm_l output pin (GPIO)
> > + */
> > +typedef struct SBTSIState {
> > + SMBusDevice parent;
> > +
> > + uint32_t temperature;
> > + uint32_t limit_low;
> > + uint32_t limit_high;
> > + uint8_t status;
> > + uint8_t config;
> > + uint8_t alert_config;
> > + uint8_t addr;
> > + qemu_irq alarm;
> > +} SBTSIState;
> > +
> > +/*
> > + * SB-TSI registers only support SMBus byte data access. "_INT" registers
> > are
> > + * the integer part of a temperature value or limit, and "_DEC" registers
> > are
> > + * corresponding decimal parts.
> > + */
> > +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
> > +#define SBTSI_REG_STATUS 0x02 /* RO */
> > +#define SBTSI_REG_CONFIG 0x03 /* RO */
> > +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
> > +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
> > +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
> > +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
> > +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
> > +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
> > +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
> > +#define SBTSI_REG_MAN 0xFE /* RO */
> > +#define SBTSI_REG_REV 0xFF /* RO */
> > +
> > +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
> > +#define SBTSI_STATUS_LOW_ALERT BIT(3)
> > +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
> > +#define SBTSI_ALARM_EN BIT(0)
> > +
> > +#define SBTSI_LIMIT_LOW_DEFAULT (0)
> > +#define SBTSI_LIMIT_HIGH_DEFAULT (560)
> > +#define SBTSI_MAN_DEFAULT (0)
> > +#define SBTSI_REV_DEFAULT (4)
> > +#define SBTSI_ALARM_L "alarm_l"
> > +
> > +/* The temperature we stored are in units of 0.125 degrees. */
> > +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
> > +
> > +/*
> > + * The integer part and decimal of the temperature both 8 bits.
> > + * Only the top 3 bits of the decimal parts are used.
> > + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875 degrees.
> > + */
> > +#define SBTSI_TEMP_MAX 255875
> > +
> > +/* The integer part of the temperature in terms of 0.125 degrees. */
> > +static uint8_t get_temp_int(uint32_t temp)
> > +{
> > + return temp >> 3;
> > +}
> > +
> > +/*
> > + * The decimal part of the temperature, in terms of 0.125 degrees.
> > + * H/W store it in the top 3 bits so we shift it by 5.
> > + */
> > +static uint8_t get_temp_dec(uint32_t temp)
> > +{
> > + return (temp & 0x7) << 5;
> > +}
> > +
> > +/*
> > + * Compute the temperature using the integer and decimal part,
> > + * in terms of 0.125 degrees. The decimal part are only the top 3 bits
> > + * so we shift it by 5 here.
> > + */
> > +static uint32_t compute_temp(uint8_t integer, uint8_t decimal)
> > +{
> > + return (integer << 3) + (decimal >> 5);
> > +}
> > +
> > +/* Compute new temp with new int part of the temperature. */
> > +static uint32_t compute_temp_int(uint32_t temp, uint8_t integer)
> > +{
> > + return compute_temp(integer, get_temp_dec(temp));
> > +}
> > +
> > +/* Compute new temp with new dec part of the temperature. */
> > +static uint32_t compute_temp_dec(uint32_t temp, uint8_t decimal)
> > +{
> > + return compute_temp(get_temp_int(temp), decimal);
> > +}
> > +
> > +/* The integer part of the temperature. */
> > +static void sbtsi_update_status(SBTSIState *s)
> > +{
> > + s->status = 0;
> > + if (s->alert_config & SBTSI_ALARM_EN) {
> > + if (s->temperature >= s->limit_high) {
> > + s->status |= SBTSI_STATUS_HIGH_ALERT;
> > + }
> > + if (s->temperature <= s->limit_low) {
> > + s->status |= SBTSI_STATUS_LOW_ALERT;
> > + }
> > + }
> > +}
> > +
> > +static void sbtsi_update_alarm(SBTSIState *s)
> > +{
> > + sbtsi_update_status(s);
> > + if (s->status != 0 && !(s->config & SBTSI_CONFIG_ALERT_MASK)) {
> > + qemu_irq_raise(s->alarm);
> > + } else {
> > + qemu_irq_lower(s->alarm);
> > + }
> > +}
> > +
> > +static uint8_t sbtsi_read_byte(SMBusDevice *d)
> > +{
> > + SBTSIState *s = SBTSI(d);
> > + uint8_t data = 0;
> > +
> > + switch (s->addr) {
> > + case SBTSI_REG_TEMP_INT:
> > + data = get_temp_int(s->temperature);
> > + break;
> > +
> > + case SBTSI_REG_TEMP_DEC:
> > + data = get_temp_dec(s->temperature);
> > + break;
> > +
> > + case SBTSI_REG_TEMP_HIGH_INT:
> > + data = get_temp_int(s->limit_high);
> > + break;
> > +
> > + case SBTSI_REG_TEMP_LOW_INT:
> > + data = get_temp_int(s->limit_low);
> > + break;
> > +
> > + case SBTSI_REG_TEMP_HIGH_DEC:
> > + data = get_temp_dec(s->limit_high);
> > + break;
> > +
> > + case SBTSI_REG_TEMP_LOW_DEC:
> > + data = get_temp_dec(s->limit_low);
> > + break;
> > +
> > + case SBTSI_REG_CONFIG:
> > + case SBTSI_REG_CONFIG_WR:
> > + data = s->config;
> > + break;
> > +
> > + case SBTSI_REG_STATUS:
> > + sbtsi_update_alarm(s);
> > + data = s->status;
> > + break;
> > +
> > + case SBTSI_REG_ALERT_CONFIG:
> > + data = s->alert_config;
> > + break;
> > +
> > + case SBTSI_REG_MAN:
> > + data = SBTSI_MAN_DEFAULT;
> > + break;
> > +
> > + case SBTSI_REG_REV:
> > + data = SBTSI_REV_DEFAULT;
> > + break;
Does this device do some sort of auto-increment on the address when
reading/writing?
Other than that possible issue, I don't see anything else, it's pretty
straightforward.
> > +
> > + default:
> > + qemu_log_mask(LOG_GUEST_ERROR,
> > + "%s: reading from invalid reg: 0x%02x\n",
> > + __func__, s->addr);
> > + break;
> > + }
> > +
> > + trace_tmp_sbtsi_read_data(s->addr, data);
> > + return data;
> > +}
> > +
> > +static void sbtsi_write(SBTSIState *s, uint8_t data)
> > +{
> > + trace_tmp_sbtsi_write_data(s->addr, data);
> > + switch (s->addr) {
> > + case SBTSI_REG_CONFIG_WR:
> > + s->config = data;
> > + break;
> > +
> > + case SBTSI_REG_TEMP_HIGH_INT:
> > + s->limit_high = compute_temp_int(s->limit_high, data);
> > + break;
> > +
> > + case SBTSI_REG_TEMP_LOW_INT:
> > + s->limit_low = compute_temp_int(s->limit_low, data);
> > + break;
> > +
> > + case SBTSI_REG_TEMP_HIGH_DEC:
> > + s->limit_high = compute_temp_dec(s->limit_high, data);
> > + break;
> > +
> > + case SBTSI_REG_TEMP_LOW_DEC:
> > + s->limit_low = compute_temp_dec(s->limit_low, data);
> > + break;
> > +
> > + case SBTSI_REG_ALERT_CONFIG:
> > + s->alert_config = data;
> > + break;
> > +
> > + case SBTSI_REG_TEMP_INT:
> > + case SBTSI_REG_TEMP_DEC:
> > + case SBTSI_REG_CONFIG:
> > + case SBTSI_REG_STATUS:
> > + case SBTSI_REG_MAN:
> > + case SBTSI_REG_REV:
> > + qemu_log_mask(LOG_GUEST_ERROR,
> > + "%s: writing to read only reg: 0x%02x data: 0x%02x\n",
> > + __func__, s->addr, data);
> > + break;
> > +
> > + default:
> > + qemu_log_mask(LOG_GUEST_ERROR,
> > + "%s: writing to invalid reg: 0x%02x data: 0x%02x\n",
> > + __func__, s->addr, data);
> > + break;
> > + }
> > + sbtsi_update_alarm(s);
> > +}
> > +
> > +static int sbtsi_write_data(SMBusDevice *d, uint8_t *buf, uint8_t len)
> > +{
> > + SBTSIState *s = SBTSI(d);
> > +
> > + if (len == 0) {
> > + qemu_log_mask(LOG_GUEST_ERROR, "%s: writing empty data\n",
> > __func__);
> > + return -1;
> > + }
> > +
> > + s->addr = buf[0];
> > + if (len > 1) {
> > + sbtsi_write(s, buf[1]);
> > + if (len > 2) {
> > + qemu_log_mask(LOG_GUEST_ERROR, "%s: extra data at end\n",
> > __func__);
> > + }
> > + }
> > + return 0;
> > +}
> > +
> > +/* Units are millidegrees. */
> > +static void sbtsi_get_temperature(Object *obj, Visitor *v, const char
> > *name,
> > + void *opaque, Error **errp)
> > +{
> > + SBTSIState *s = SBTSI(obj);
> > + uint32_t temp = s->temperature * SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> > +
> > + visit_type_uint32(v, name, &temp, errp);
> > +}
> > +
> > +/* Units are millidegrees. */
> > +static void sbtsi_set_temperature(Object *obj, Visitor *v, const char
> > *name,
> > + void *opaque, Error **errp)
> > +{
> > + SBTSIState *s = SBTSI(obj);
> > + uint32_t temp;
> > +
> > + if (!visit_type_uint32(v, name, &temp, errp)) {
> > + return;
> > + }
> > + if (temp > SBTSI_TEMP_MAX) {
> > + error_setg(errp, "value %" PRIu32 ".%03" PRIu32 " C is out of
> > range",
> > + temp / 1000, temp % 1000);
> > + return;
> > + }
> > +
> > + s->temperature = temp / SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> > + sbtsi_update_alarm(s);
> > +}
> > +
> > +static int sbtsi_post_load(void *opaque, int version_id)
> > +{
> > + SBTSIState *s = opaque;
> > +
> > + sbtsi_update_alarm(s);
> > + return 0;
> > +}
> > +
> > +static const VMStateDescription vmstate_sbtsi = {
> > + .name = "SBTSI",
> > + .version_id = 0,
> > + .minimum_version_id = 0,
> > + .post_load = sbtsi_post_load,
> > + .fields = (VMStateField[]) {
> > + VMSTATE_UINT32(temperature, SBTSIState),
> > + VMSTATE_UINT32(limit_low, SBTSIState),
> > + VMSTATE_UINT32(limit_high, SBTSIState),
> > + VMSTATE_UINT8(config, SBTSIState),
> > + VMSTATE_UINT8(status, SBTSIState),
> > + VMSTATE_UINT8(addr, SBTSIState),
> > + VMSTATE_END_OF_LIST()
> > + }
> > +};
> > +
> > +static void sbtsi_enter_reset(Object *obj, ResetType type)
> > +{
> > + SBTSIState *s = SBTSI(obj);
> > +
> > + s->config = 0;
> > + s->limit_low = SBTSI_LIMIT_LOW_DEFAULT;
> > + s->limit_high = SBTSI_LIMIT_HIGH_DEFAULT;
> > +}
> > +
> > +static void sbtsi_hold_reset(Object *obj)
> > +{
> > + SBTSIState *s = SBTSI(obj);
> > +
> > + qemu_irq_lower(s->alarm);
> > +}
> > +
> > +static void sbtsi_init(Object *obj)
> > +{
> > + SBTSIState *s = SBTSI(obj);
> > +
> > + /* Current temperature in millidegrees. */
> > + object_property_add(obj, "temperature", "uint32",
> > + sbtsi_get_temperature, sbtsi_set_temperature,
> > + NULL, NULL);
> > + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm, SBTSI_ALARM_L, 0);
> > +}
> > +
> > +static void sbtsi_class_init(ObjectClass *klass, void *data)
> > +{
> > + ResettableClass *rc = RESETTABLE_CLASS(klass);
> > + DeviceClass *dc = DEVICE_CLASS(klass);
> > + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
> > +
> > + dc->desc = "SB-TSI Temperature Sensor";
> > + dc->vmsd = &vmstate_sbtsi;
> > + k->write_data = sbtsi_write_data;
> > + k->receive_byte = sbtsi_read_byte;
> > + rc->phases.enter = sbtsi_enter_reset;
> > + rc->phases.hold = sbtsi_hold_reset;
> > +}
> > +
> > +static const TypeInfo sbtsi_info = {
> > + .name = TYPE_SBTSI,
> > + .parent = TYPE_SMBUS_DEVICE,
> > + .instance_size = sizeof(SBTSIState),
> > + .instance_init = sbtsi_init,
> > + .class_init = sbtsi_class_init,
> > +};
> > +
> > +static void sbtsi_register_types(void)
> > +{
> > + type_register_static(&sbtsi_info);
> > +}
> > +
> > +type_init(sbtsi_register_types)
> > diff --git a/hw/sensor/trace-events b/hw/sensor/trace-events
> > new file mode 100644
> > index 0000000000..21ab3809e2
> > --- /dev/null
> > +++ b/hw/sensor/trace-events
> > @@ -0,0 +1,5 @@
> > +# See docs/devel/tracing.rst for syntax documentation.
> > +
> > +# tmp_sbtsi.c
> > +tmp_sbtsi_write_data(uint8_t addr, uint8_t value) "SBTSI write
> > addr:0x%02x data: 0x%02x"
> > +tmp_sbtsi_read_data(uint8_t addr, uint8_t value) "SBTSI read addr:0x%02x
> > data: 0x%02x"
> > diff --git a/hw/sensor/trace.h b/hw/sensor/trace.h
> > new file mode 100644
> > index 0000000000..e4721560b0
> > --- /dev/null
> > +++ b/hw/sensor/trace.h
> > @@ -0,0 +1 @@
> > +#include "trace/trace-hw_sensor.h"
> > diff --git a/meson.build b/meson.build
> > index 53065e96ec..f8ab0bf74e 100644
> > --- a/meson.build
> > +++ b/meson.build
> > @@ -2494,6 +2494,7 @@ if have_system
> > 'hw/rtc',
> > 'hw/s390x',
> > 'hw/scsi',
> > + 'hw/sensor',
> > 'hw/sd',
> > 'hw/sh4',
> > 'hw/sparc',
> > diff --git a/tests/qtest/meson.build b/tests/qtest/meson.build
> > index 37e1eaa449..d1a8c38f74 100644
> > --- a/tests/qtest/meson.build
> > +++ b/tests/qtest/meson.build
> > @@ -254,6 +254,7 @@ qos_test_ss.add(
> > 'spapr-phb-test.c',
> > 'tmp105-test.c',
> > 'emc141x-test.c',
> > + 'tmp_sbtsi-test.c',
> > 'usb-hcd-ohci-test.c',
> > 'virtio-test.c',
> > 'virtio-blk-test.c',
> > diff --git a/tests/qtest/tmp_sbtsi-test.c b/tests/qtest/tmp_sbtsi-test.c
> > new file mode 100644
> > index 0000000000..7f5fafacc7
> > --- /dev/null
> > +++ b/tests/qtest/tmp_sbtsi-test.c
> > @@ -0,0 +1,180 @@
> > +/*
> > + * QTests for the SBTSI temperature sensor
> > + *
> > + * Copyright 2020 Google LLC
> > + *
> > + * This program is free software; you can redistribute it and/or modify it
> > + * under the terms of the GNU General Public License as published by the
> > + * Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful, but
> > WITHOUT
> > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
> > + * for more details.
> > + */
> > +
> > +#include "qemu/osdep.h"
> > +
> > +#include "libqtest-single.h"
> > +#include "libqos/qgraph.h"
> > +#include "libqos/i2c.h"
> > +#include "qapi/qmp/qdict.h"
> > +#include "qemu/bitops.h"
> > +
> > +#define TEST_ID "sbtsi-test"
> > +#define TEST_ADDR (0x4c)
> > +
> > +/*
> > + * SB-TSI registers only support SMBus byte data access. "_INT" registers
> > are
> > + * the integer part of a temperature value or limit, and "_DEC" registers
> > are
> > + * corresponding decimal parts.
> > + */
> > +#define REG_TEMP_INT 0x01 /* RO */
> > +#define REG_STATUS 0x02 /* RO */
> > +#define REG_CONFIG 0x03 /* RO */
> > +#define REG_TEMP_HIGH_INT 0x07 /* RW */
> > +#define REG_TEMP_LOW_INT 0x08 /* RW */
> > +#define REG_CONFIG_WR 0x09 /* RW */
> > +#define REG_TEMP_DEC 0x10 /* RO */
> > +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
> > +#define REG_TEMP_LOW_DEC 0x14 /* RW */
> > +#define REG_ALERT_CONFIG 0xBF /* RW */
> > +
> > +#define STATUS_HIGH_ALERT BIT(4)
> > +#define STATUS_LOW_ALERT BIT(3)
> > +#define CONFIG_ALERT_MASK BIT(7)
> > +#define ALARM_EN BIT(0)
> > +
> > +/* The temperature stored are in units of 0.125 degrees. */
> > +#define TEMP_UNIT_IN_MILLIDEGREE 125
> > +#define LIMIT_LOW (10500)
> > +#define LIMIT_HIGH (55125)
> > +
> > +static uint32_t qmp_sbtsi_get_temperature(const char *id)
> > +{
> > + QDict *response;
> > + int ret;
> > +
> > + response = qmp("{ 'execute': 'qom-get', 'arguments': { 'path': %s, "
> > + "'property': 'temperature' } }", id);
> > + g_assert(qdict_haskey(response, "return"));
> > + ret = (uint32_t)qdict_get_int(response, "return");
> > + qobject_unref(response);
> > + return ret;
> > +}
> > +
> > +static void qmp_sbtsi_set_temperature(const char *id, uint32_t value)
> > +{
> > + QDict *response;
> > +
> > + response = qmp("{ 'execute': 'qom-set', 'arguments': { 'path': %s, "
> > + "'property': 'temperature', 'value': %d } }", id,
> > value);
> > + g_assert(qdict_haskey(response, "return"));
> > + qobject_unref(response);
> > +}
> > +
> > +/*
> > + * Compute the temperature using the integer and decimal part and return
> > + * millidegrees. The decimal part are only the top 3 bits so we shift it
> > by
> > + * 5 here.
> > + */
> > +static uint32_t regs_to_temp(uint8_t integer, uint8_t decimal)
> > +{
> > + return ((integer << 3) + (decimal >> 5)) * TEMP_UNIT_IN_MILLIDEGREE;
> > +}
> > +
> > +/*
> > + * Compute the integer and decimal parts of the temperature in
> > millidegrees.
> > + * H/W store the decimal in the top 3 bits so we shift it by 5.
> > + */
> > +static void temp_to_regs(uint32_t temp, uint8_t *integer, uint8_t
> > *decimal)
> > +{
> > + temp /= TEMP_UNIT_IN_MILLIDEGREE;
> > + *integer = temp >> 3;
> > + *decimal = (temp & 0x7) << 5;
> > +}
> > +
> > +static void tx_rx(void *obj, void *data, QGuestAllocator *alloc)
> > +{
> > + uint16_t value;
> > + uint8_t integer, decimal;
> > + QI2CDevice *i2cdev = (QI2CDevice *)obj;
> > +
> > + /* Test default values */
> > + value = qmp_sbtsi_get_temperature(TEST_ID);
> > + g_assert_cmpuint(value, ==, 0);
> > +
> > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 0);
> > +
> > + /* Test setting temperature */
> > + qmp_sbtsi_set_temperature(TEST_ID, 20000);
> > + value = qmp_sbtsi_get_temperature(TEST_ID);
> > + g_assert_cmpuint(value, ==, 20000);
> > +
> > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 20000);
> > +
> > + /* Set alert mask in config */
> > + i2c_set8(i2cdev, REG_CONFIG_WR, CONFIG_ALERT_MASK);
> > + value = i2c_get8(i2cdev, REG_CONFIG);
> > + g_assert_cmphex(value, ==, CONFIG_ALERT_MASK);
> > + /* Enable alarm_en */
> > + i2c_set8(i2cdev, REG_ALERT_CONFIG, ALARM_EN);
> > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> > + g_assert_cmphex(value, ==, ALARM_EN);
> > +
> > + /* Test setting limits */
> > + /* Limit low = 10.500 */
> > + temp_to_regs(LIMIT_LOW, &integer, &decimal);
> > + i2c_set8(i2cdev, REG_TEMP_LOW_INT, integer);
> > + i2c_set8(i2cdev, REG_TEMP_LOW_DEC, decimal);
> > + integer = i2c_get8(i2cdev, REG_TEMP_LOW_INT);
> > + decimal = i2c_get8(i2cdev, REG_TEMP_LOW_DEC);
> > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_LOW);
> > + /* Limit high = 55.125 */
> > + temp_to_regs(LIMIT_HIGH, &integer, &decimal);
> > + i2c_set8(i2cdev, REG_TEMP_HIGH_INT, integer);
> > + i2c_set8(i2cdev, REG_TEMP_HIGH_DEC, decimal);
> > + integer = i2c_get8(i2cdev, REG_TEMP_HIGH_INT);
> > + decimal = i2c_get8(i2cdev, REG_TEMP_HIGH_DEC);
> > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_HIGH);
> > + /* No alert is generated. */
> > + value = i2c_get8(i2cdev, REG_STATUS);
> > + g_assert_cmphex(value, ==, 0);
> > +
> > + /* Test alert for low temperature */
> > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_LOW);
> > + value = i2c_get8(i2cdev, REG_STATUS);
> > + g_assert_cmphex(value, ==, STATUS_LOW_ALERT);
> > +
> > + /* Test alert for high temperature */
> > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_HIGH);
> > + value = i2c_get8(i2cdev, REG_STATUS);
> > + g_assert_cmphex(value, ==, STATUS_HIGH_ALERT);
> > +
> > + /* Disable alarm_en */
> > + i2c_set8(i2cdev, REG_ALERT_CONFIG, 0);
> > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> > + g_assert_cmphex(value, ==, 0);
> > + /* No alert when alarm_en is false. */
> > + value = i2c_get8(i2cdev, REG_STATUS);
> > + g_assert_cmphex(value, ==, 0);
> > +}
> > +
> > +static void sbtsi_register_nodes(void)
> > +{
> > + QOSGraphEdgeOptions opts = {
> > + .extra_device_opts = "id=" TEST_ID ",address=0x4c"
> > + };
> > + add_qi2c_address(&opts, &(QI2CAddress) { TEST_ADDR });
> > +
> > + qos_node_create_driver("sbtsi", i2c_device_create);
> > + qos_node_consumes("sbtsi", "i2c-bus", &opts);
> > +
> > + qos_add_test("tx-rx", "sbtsi", tx_rx, NULL);
> > +}
> > +libqos_init(sbtsi_register_nodes);
> > --
>
>
> + Corey for i2c maintainer. The new sensor directory is mostly if not
> entirely i2c devices. I didn't create a maintainer entry for this i2c
> device, but I can if desired and send out a v2.
Yeah, I guess I should be maintainer there. I'll queue up a change for
that. Thanks.
-corey
>
>
> > 2.34.1.575.g55b058a8bb-goog
> >
> >
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-17 14:05 ` Corey Minyard
@ 2022-01-18 17:10 ` Patrick Venture
2022-01-27 0:09 ` Hao Wu
0 siblings, 1 reply; 15+ messages in thread
From: Patrick Venture @ 2022-01-18 17:10 UTC (permalink / raw)
To: Corey Minyard, Hao Wu
Cc: Thomas Huth, lvivier, Paolo Bonzini, QEMU Developers, Doug Evans
[-- Attachment #1: Type: text/plain, Size: 25899 bytes --]
On Mon, Jan 17, 2022 at 6:05 AM Corey Minyard <cminyard@mvista.com> wrote:
> On Sun, Jan 09, 2022 at 06:17:34PM -0800, Patrick Venture wrote:
> > On Fri, Jan 7, 2022 at 7:04 PM Patrick Venture <venture@google.com>
> wrote:
> >
> > > From: Hao Wu <wuhaotsh@google.com>
> > >
> > > SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
> > > interface that reports AMD SoC's Ttcl (normalized temperature),
> > > and resembles a typical 8-pin remote temperature sensor's I2C interface
> > > to BMC.
> > >
> > > This patch implements a basic AMD SB-TSI sensor that is
> > > compatible with the open-source data sheet from AMD and Linux
> > > kernel driver.
> > >
> > > Reference:
> > > Linux kernel driver:
> > > https://lkml.org/lkml/2020/12/11/968
> > > Register Map:
> > > https://developer.amd.com/wp-content/resources/56255_3_03.PDF
> > > (Chapter 6)
> > >
> > > Signed-off-by: Hao Wu <wuhaotsh@google.com>
> > > Reviewed-by: Doug Evans <dje@google.com>
> > > ---
> > > hw/sensor/Kconfig | 4 +
> > > hw/sensor/meson.build | 1 +
> > > hw/sensor/tmp_sbtsi.c | 393 +++++++++++++++++++++++++++++++++++
> > > hw/sensor/trace-events | 5 +
> > > hw/sensor/trace.h | 1 +
> > > meson.build | 1 +
> > > tests/qtest/meson.build | 1 +
> > > tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
> > > 8 files changed, 586 insertions(+)
> > > create mode 100644 hw/sensor/tmp_sbtsi.c
> > > create mode 100644 hw/sensor/trace-events
> > > create mode 100644 hw/sensor/trace.h
> > > create mode 100644 tests/qtest/tmp_sbtsi-test.c
> > >
> > > diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
> > > index 9c8a049b06..27f6f79c84 100644
> > > --- a/hw/sensor/Kconfig
> > > +++ b/hw/sensor/Kconfig
> > > @@ -21,3 +21,7 @@ config ADM1272
> > > config MAX34451
> > > bool
> > > depends on I2C
> > > +
> > > +config AMDSBTSI
> > > + bool
> > > + depends on I2C
> > > diff --git a/hw/sensor/meson.build b/hw/sensor/meson.build
> > > index 059c4ca935..f7b0e645eb 100644
> > > --- a/hw/sensor/meson.build
> > > +++ b/hw/sensor/meson.build
> > > @@ -4,3 +4,4 @@ softmmu_ss.add(when: 'CONFIG_DPS310', if_true:
> > > files('dps310.c'))
> > > softmmu_ss.add(when: 'CONFIG_EMC141X', if_true: files('emc141x.c'))
> > > softmmu_ss.add(when: 'CONFIG_ADM1272', if_true: files('adm1272.c'))
> > > softmmu_ss.add(when: 'CONFIG_MAX34451', if_true: files('max34451.c'))
> > > +softmmu_ss.add(when: 'CONFIG_AMDSBTSI', if_true: files('tmp_sbtsi.c'))
> > > diff --git a/hw/sensor/tmp_sbtsi.c b/hw/sensor/tmp_sbtsi.c
> > > new file mode 100644
> > > index 0000000000..b68c7ebf61
> > > --- /dev/null
> > > +++ b/hw/sensor/tmp_sbtsi.c
> > > @@ -0,0 +1,393 @@
> > > +/*
> > > + * AMD SBI Temperature Sensor Interface (SB-TSI)
> > > + *
> > > + * Copyright 2021 Google LLC
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> modify it
> > > + * under the terms of the GNU General Public License as published by
> the
> > > + * Free Software Foundation; either version 2 of the License, or
> > > + * (at your option) any later version.
> > > + *
> > > + * This program is distributed in the hope that it will be useful, but
> > > WITHOUT
> > > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
> or
> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> License
> > > + * for more details.
> > > + */
> > > +
> > > +#include "qemu/osdep.h"
> > > +#include "hw/i2c/smbus_slave.h"
> > > +#include "hw/irq.h"
> > > +#include "migration/vmstate.h"
> > > +#include "qapi/error.h"
> > > +#include "qapi/visitor.h"
> > > +#include "qemu/log.h"
> > > +#include "qemu/module.h"
> > > +#include "trace.h"
> > > +
> > > +#define TYPE_SBTSI "sbtsi"
> > > +#define SBTSI(obj) OBJECT_CHECK(SBTSIState, (obj), TYPE_SBTSI)
> > > +
> > > +/**
> > > + * SBTSIState:
> > > + * temperatures are in units of 0.125 degrees
> > > + * @temperature: Temperature
> > > + * @limit_low: Lowest temperature
> > > + * @limit_high: Highest temperature
> > > + * @status: The status register
> > > + * @config: The config register
> > > + * @alert_config: The config for alarm_l output.
> > > + * @addr: The address to read/write for the next cmd.
> > > + * @alarm: The alarm_l output pin (GPIO)
> > > + */
> > > +typedef struct SBTSIState {
> > > + SMBusDevice parent;
> > > +
> > > + uint32_t temperature;
> > > + uint32_t limit_low;
> > > + uint32_t limit_high;
> > > + uint8_t status;
> > > + uint8_t config;
> > > + uint8_t alert_config;
> > > + uint8_t addr;
> > > + qemu_irq alarm;
> > > +} SBTSIState;
> > > +
> > > +/*
> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
> registers
> > > are
> > > + * the integer part of a temperature value or limit, and "_DEC"
> registers
> > > are
> > > + * corresponding decimal parts.
> > > + */
> > > +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
> > > +#define SBTSI_REG_STATUS 0x02 /* RO */
> > > +#define SBTSI_REG_CONFIG 0x03 /* RO */
> > > +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
> > > +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
> > > +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
> > > +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
> > > +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
> > > +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
> > > +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
> > > +#define SBTSI_REG_MAN 0xFE /* RO */
> > > +#define SBTSI_REG_REV 0xFF /* RO */
> > > +
> > > +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
> > > +#define SBTSI_STATUS_LOW_ALERT BIT(3)
> > > +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
> > > +#define SBTSI_ALARM_EN BIT(0)
> > > +
> > > +#define SBTSI_LIMIT_LOW_DEFAULT (0)
> > > +#define SBTSI_LIMIT_HIGH_DEFAULT (560)
> > > +#define SBTSI_MAN_DEFAULT (0)
> > > +#define SBTSI_REV_DEFAULT (4)
> > > +#define SBTSI_ALARM_L "alarm_l"
> > > +
> > > +/* The temperature we stored are in units of 0.125 degrees. */
> > > +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
> > > +
> > > +/*
> > > + * The integer part and decimal of the temperature both 8 bits.
> > > + * Only the top 3 bits of the decimal parts are used.
> > > + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875 degrees.
> > > + */
> > > +#define SBTSI_TEMP_MAX 255875
> > > +
> > > +/* The integer part of the temperature in terms of 0.125 degrees. */
> > > +static uint8_t get_temp_int(uint32_t temp)
> > > +{
> > > + return temp >> 3;
> > > +}
> > > +
> > > +/*
> > > + * The decimal part of the temperature, in terms of 0.125 degrees.
> > > + * H/W store it in the top 3 bits so we shift it by 5.
> > > + */
> > > +static uint8_t get_temp_dec(uint32_t temp)
> > > +{
> > > + return (temp & 0x7) << 5;
> > > +}
> > > +
> > > +/*
> > > + * Compute the temperature using the integer and decimal part,
> > > + * in terms of 0.125 degrees. The decimal part are only the top 3 bits
> > > + * so we shift it by 5 here.
> > > + */
> > > +static uint32_t compute_temp(uint8_t integer, uint8_t decimal)
> > > +{
> > > + return (integer << 3) + (decimal >> 5);
> > > +}
> > > +
> > > +/* Compute new temp with new int part of the temperature. */
> > > +static uint32_t compute_temp_int(uint32_t temp, uint8_t integer)
> > > +{
> > > + return compute_temp(integer, get_temp_dec(temp));
> > > +}
> > > +
> > > +/* Compute new temp with new dec part of the temperature. */
> > > +static uint32_t compute_temp_dec(uint32_t temp, uint8_t decimal)
> > > +{
> > > + return compute_temp(get_temp_int(temp), decimal);
> > > +}
> > > +
> > > +/* The integer part of the temperature. */
> > > +static void sbtsi_update_status(SBTSIState *s)
> > > +{
> > > + s->status = 0;
> > > + if (s->alert_config & SBTSI_ALARM_EN) {
> > > + if (s->temperature >= s->limit_high) {
> > > + s->status |= SBTSI_STATUS_HIGH_ALERT;
> > > + }
> > > + if (s->temperature <= s->limit_low) {
> > > + s->status |= SBTSI_STATUS_LOW_ALERT;
> > > + }
> > > + }
> > > +}
> > > +
> > > +static void sbtsi_update_alarm(SBTSIState *s)
> > > +{
> > > + sbtsi_update_status(s);
> > > + if (s->status != 0 && !(s->config & SBTSI_CONFIG_ALERT_MASK)) {
> > > + qemu_irq_raise(s->alarm);
> > > + } else {
> > > + qemu_irq_lower(s->alarm);
> > > + }
> > > +}
> > > +
> > > +static uint8_t sbtsi_read_byte(SMBusDevice *d)
> > > +{
> > > + SBTSIState *s = SBTSI(d);
> > > + uint8_t data = 0;
> > > +
> > > + switch (s->addr) {
> > > + case SBTSI_REG_TEMP_INT:
> > > + data = get_temp_int(s->temperature);
> > > + break;
> > > +
> > > + case SBTSI_REG_TEMP_DEC:
> > > + data = get_temp_dec(s->temperature);
> > > + break;
> > > +
> > > + case SBTSI_REG_TEMP_HIGH_INT:
> > > + data = get_temp_int(s->limit_high);
> > > + break;
> > > +
> > > + case SBTSI_REG_TEMP_LOW_INT:
> > > + data = get_temp_int(s->limit_low);
> > > + break;
> > > +
> > > + case SBTSI_REG_TEMP_HIGH_DEC:
> > > + data = get_temp_dec(s->limit_high);
> > > + break;
> > > +
> > > + case SBTSI_REG_TEMP_LOW_DEC:
> > > + data = get_temp_dec(s->limit_low);
> > > + break;
> > > +
> > > + case SBTSI_REG_CONFIG:
> > > + case SBTSI_REG_CONFIG_WR:
> > > + data = s->config;
> > > + break;
> > > +
> > > + case SBTSI_REG_STATUS:
> > > + sbtsi_update_alarm(s);
> > > + data = s->status;
> > > + break;
> > > +
> > > + case SBTSI_REG_ALERT_CONFIG:
> > > + data = s->alert_config;
> > > + break;
> > > +
> > > + case SBTSI_REG_MAN:
> > > + data = SBTSI_MAN_DEFAULT;
> > > + break;
> > > +
> > > + case SBTSI_REG_REV:
> > > + data = SBTSI_REV_DEFAULT;
> > > + break;
>
> Does this device do some sort of auto-increment on the address when
> reading/writing?
>
+Hao Wu <wuhaotsh@google.com> - Please take a look at the above
question. I imagine it's a while since you've thought about it, but please
double check :)
Thanks!
> Other than that possible issue, I don't see anything else, it's pretty
> straightforward.
>
> > > +
> > > + default:
> > > + qemu_log_mask(LOG_GUEST_ERROR,
> > > + "%s: reading from invalid reg: 0x%02x\n",
> > > + __func__, s->addr);
> > > + break;
> > > + }
> > > +
> > > + trace_tmp_sbtsi_read_data(s->addr, data);
> > > + return data;
> > > +}
> > > +
> > > +static void sbtsi_write(SBTSIState *s, uint8_t data)
> > > +{
> > > + trace_tmp_sbtsi_write_data(s->addr, data);
> > > + switch (s->addr) {
> > > + case SBTSI_REG_CONFIG_WR:
> > > + s->config = data;
> > > + break;
> > > +
> > > + case SBTSI_REG_TEMP_HIGH_INT:
> > > + s->limit_high = compute_temp_int(s->limit_high, data);
> > > + break;
> > > +
> > > + case SBTSI_REG_TEMP_LOW_INT:
> > > + s->limit_low = compute_temp_int(s->limit_low, data);
> > > + break;
> > > +
> > > + case SBTSI_REG_TEMP_HIGH_DEC:
> > > + s->limit_high = compute_temp_dec(s->limit_high, data);
> > > + break;
> > > +
> > > + case SBTSI_REG_TEMP_LOW_DEC:
> > > + s->limit_low = compute_temp_dec(s->limit_low, data);
> > > + break;
> > > +
> > > + case SBTSI_REG_ALERT_CONFIG:
> > > + s->alert_config = data;
> > > + break;
> > > +
> > > + case SBTSI_REG_TEMP_INT:
> > > + case SBTSI_REG_TEMP_DEC:
> > > + case SBTSI_REG_CONFIG:
> > > + case SBTSI_REG_STATUS:
> > > + case SBTSI_REG_MAN:
> > > + case SBTSI_REG_REV:
> > > + qemu_log_mask(LOG_GUEST_ERROR,
> > > + "%s: writing to read only reg: 0x%02x data: 0x%02x\n",
> > > + __func__, s->addr, data);
> > > + break;
> > > +
> > > + default:
> > > + qemu_log_mask(LOG_GUEST_ERROR,
> > > + "%s: writing to invalid reg: 0x%02x data: 0x%02x\n",
> > > + __func__, s->addr, data);
> > > + break;
> > > + }
> > > + sbtsi_update_alarm(s);
> > > +}
> > > +
> > > +static int sbtsi_write_data(SMBusDevice *d, uint8_t *buf, uint8_t len)
> > > +{
> > > + SBTSIState *s = SBTSI(d);
> > > +
> > > + if (len == 0) {
> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: writing empty data\n",
> > > __func__);
> > > + return -1;
> > > + }
> > > +
> > > + s->addr = buf[0];
> > > + if (len > 1) {
> > > + sbtsi_write(s, buf[1]);
> > > + if (len > 2) {
> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: extra data at end\n",
> > > __func__);
> > > + }
> > > + }
> > > + return 0;
> > > +}
> > > +
> > > +/* Units are millidegrees. */
> > > +static void sbtsi_get_temperature(Object *obj, Visitor *v, const char
> > > *name,
> > > + void *opaque, Error **errp)
> > > +{
> > > + SBTSIState *s = SBTSI(obj);
> > > + uint32_t temp = s->temperature * SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> > > +
> > > + visit_type_uint32(v, name, &temp, errp);
> > > +}
> > > +
> > > +/* Units are millidegrees. */
> > > +static void sbtsi_set_temperature(Object *obj, Visitor *v, const char
> > > *name,
> > > + void *opaque, Error **errp)
> > > +{
> > > + SBTSIState *s = SBTSI(obj);
> > > + uint32_t temp;
> > > +
> > > + if (!visit_type_uint32(v, name, &temp, errp)) {
> > > + return;
> > > + }
> > > + if (temp > SBTSI_TEMP_MAX) {
> > > + error_setg(errp, "value %" PRIu32 ".%03" PRIu32 " C is out of
> > > range",
> > > + temp / 1000, temp % 1000);
> > > + return;
> > > + }
> > > +
> > > + s->temperature = temp / SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> > > + sbtsi_update_alarm(s);
> > > +}
> > > +
> > > +static int sbtsi_post_load(void *opaque, int version_id)
> > > +{
> > > + SBTSIState *s = opaque;
> > > +
> > > + sbtsi_update_alarm(s);
> > > + return 0;
> > > +}
> > > +
> > > +static const VMStateDescription vmstate_sbtsi = {
> > > + .name = "SBTSI",
> > > + .version_id = 0,
> > > + .minimum_version_id = 0,
> > > + .post_load = sbtsi_post_load,
> > > + .fields = (VMStateField[]) {
> > > + VMSTATE_UINT32(temperature, SBTSIState),
> > > + VMSTATE_UINT32(limit_low, SBTSIState),
> > > + VMSTATE_UINT32(limit_high, SBTSIState),
> > > + VMSTATE_UINT8(config, SBTSIState),
> > > + VMSTATE_UINT8(status, SBTSIState),
> > > + VMSTATE_UINT8(addr, SBTSIState),
> > > + VMSTATE_END_OF_LIST()
> > > + }
> > > +};
> > > +
> > > +static void sbtsi_enter_reset(Object *obj, ResetType type)
> > > +{
> > > + SBTSIState *s = SBTSI(obj);
> > > +
> > > + s->config = 0;
> > > + s->limit_low = SBTSI_LIMIT_LOW_DEFAULT;
> > > + s->limit_high = SBTSI_LIMIT_HIGH_DEFAULT;
> > > +}
> > > +
> > > +static void sbtsi_hold_reset(Object *obj)
> > > +{
> > > + SBTSIState *s = SBTSI(obj);
> > > +
> > > + qemu_irq_lower(s->alarm);
> > > +}
> > > +
> > > +static void sbtsi_init(Object *obj)
> > > +{
> > > + SBTSIState *s = SBTSI(obj);
> > > +
> > > + /* Current temperature in millidegrees. */
> > > + object_property_add(obj, "temperature", "uint32",
> > > + sbtsi_get_temperature, sbtsi_set_temperature,
> > > + NULL, NULL);
> > > + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm, SBTSI_ALARM_L,
> 0);
> > > +}
> > > +
> > > +static void sbtsi_class_init(ObjectClass *klass, void *data)
> > > +{
> > > + ResettableClass *rc = RESETTABLE_CLASS(klass);
> > > + DeviceClass *dc = DEVICE_CLASS(klass);
> > > + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
> > > +
> > > + dc->desc = "SB-TSI Temperature Sensor";
> > > + dc->vmsd = &vmstate_sbtsi;
> > > + k->write_data = sbtsi_write_data;
> > > + k->receive_byte = sbtsi_read_byte;
> > > + rc->phases.enter = sbtsi_enter_reset;
> > > + rc->phases.hold = sbtsi_hold_reset;
> > > +}
> > > +
> > > +static const TypeInfo sbtsi_info = {
> > > + .name = TYPE_SBTSI,
> > > + .parent = TYPE_SMBUS_DEVICE,
> > > + .instance_size = sizeof(SBTSIState),
> > > + .instance_init = sbtsi_init,
> > > + .class_init = sbtsi_class_init,
> > > +};
> > > +
> > > +static void sbtsi_register_types(void)
> > > +{
> > > + type_register_static(&sbtsi_info);
> > > +}
> > > +
> > > +type_init(sbtsi_register_types)
> > > diff --git a/hw/sensor/trace-events b/hw/sensor/trace-events
> > > new file mode 100644
> > > index 0000000000..21ab3809e2
> > > --- /dev/null
> > > +++ b/hw/sensor/trace-events
> > > @@ -0,0 +1,5 @@
> > > +# See docs/devel/tracing.rst for syntax documentation.
> > > +
> > > +# tmp_sbtsi.c
> > > +tmp_sbtsi_write_data(uint8_t addr, uint8_t value) "SBTSI write
> > > addr:0x%02x data: 0x%02x"
> > > +tmp_sbtsi_read_data(uint8_t addr, uint8_t value) "SBTSI read
> addr:0x%02x
> > > data: 0x%02x"
> > > diff --git a/hw/sensor/trace.h b/hw/sensor/trace.h
> > > new file mode 100644
> > > index 0000000000..e4721560b0
> > > --- /dev/null
> > > +++ b/hw/sensor/trace.h
> > > @@ -0,0 +1 @@
> > > +#include "trace/trace-hw_sensor.h"
> > > diff --git a/meson.build b/meson.build
> > > index 53065e96ec..f8ab0bf74e 100644
> > > --- a/meson.build
> > > +++ b/meson.build
> > > @@ -2494,6 +2494,7 @@ if have_system
> > > 'hw/rtc',
> > > 'hw/s390x',
> > > 'hw/scsi',
> > > + 'hw/sensor',
> > > 'hw/sd',
> > > 'hw/sh4',
> > > 'hw/sparc',
> > > diff --git a/tests/qtest/meson.build b/tests/qtest/meson.build
> > > index 37e1eaa449..d1a8c38f74 100644
> > > --- a/tests/qtest/meson.build
> > > +++ b/tests/qtest/meson.build
> > > @@ -254,6 +254,7 @@ qos_test_ss.add(
> > > 'spapr-phb-test.c',
> > > 'tmp105-test.c',
> > > 'emc141x-test.c',
> > > + 'tmp_sbtsi-test.c',
> > > 'usb-hcd-ohci-test.c',
> > > 'virtio-test.c',
> > > 'virtio-blk-test.c',
> > > diff --git a/tests/qtest/tmp_sbtsi-test.c
> b/tests/qtest/tmp_sbtsi-test.c
> > > new file mode 100644
> > > index 0000000000..7f5fafacc7
> > > --- /dev/null
> > > +++ b/tests/qtest/tmp_sbtsi-test.c
> > > @@ -0,0 +1,180 @@
> > > +/*
> > > + * QTests for the SBTSI temperature sensor
> > > + *
> > > + * Copyright 2020 Google LLC
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> modify it
> > > + * under the terms of the GNU General Public License as published by
> the
> > > + * Free Software Foundation; either version 2 of the License, or
> > > + * (at your option) any later version.
> > > + *
> > > + * This program is distributed in the hope that it will be useful, but
> > > WITHOUT
> > > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
> or
> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> License
> > > + * for more details.
> > > + */
> > > +
> > > +#include "qemu/osdep.h"
> > > +
> > > +#include "libqtest-single.h"
> > > +#include "libqos/qgraph.h"
> > > +#include "libqos/i2c.h"
> > > +#include "qapi/qmp/qdict.h"
> > > +#include "qemu/bitops.h"
> > > +
> > > +#define TEST_ID "sbtsi-test"
> > > +#define TEST_ADDR (0x4c)
> > > +
> > > +/*
> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
> registers
> > > are
> > > + * the integer part of a temperature value or limit, and "_DEC"
> registers
> > > are
> > > + * corresponding decimal parts.
> > > + */
> > > +#define REG_TEMP_INT 0x01 /* RO */
> > > +#define REG_STATUS 0x02 /* RO */
> > > +#define REG_CONFIG 0x03 /* RO */
> > > +#define REG_TEMP_HIGH_INT 0x07 /* RW */
> > > +#define REG_TEMP_LOW_INT 0x08 /* RW */
> > > +#define REG_CONFIG_WR 0x09 /* RW */
> > > +#define REG_TEMP_DEC 0x10 /* RO */
> > > +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
> > > +#define REG_TEMP_LOW_DEC 0x14 /* RW */
> > > +#define REG_ALERT_CONFIG 0xBF /* RW */
> > > +
> > > +#define STATUS_HIGH_ALERT BIT(4)
> > > +#define STATUS_LOW_ALERT BIT(3)
> > > +#define CONFIG_ALERT_MASK BIT(7)
> > > +#define ALARM_EN BIT(0)
> > > +
> > > +/* The temperature stored are in units of 0.125 degrees. */
> > > +#define TEMP_UNIT_IN_MILLIDEGREE 125
> > > +#define LIMIT_LOW (10500)
> > > +#define LIMIT_HIGH (55125)
> > > +
> > > +static uint32_t qmp_sbtsi_get_temperature(const char *id)
> > > +{
> > > + QDict *response;
> > > + int ret;
> > > +
> > > + response = qmp("{ 'execute': 'qom-get', 'arguments': { 'path':
> %s, "
> > > + "'property': 'temperature' } }", id);
> > > + g_assert(qdict_haskey(response, "return"));
> > > + ret = (uint32_t)qdict_get_int(response, "return");
> > > + qobject_unref(response);
> > > + return ret;
> > > +}
> > > +
> > > +static void qmp_sbtsi_set_temperature(const char *id, uint32_t value)
> > > +{
> > > + QDict *response;
> > > +
> > > + response = qmp("{ 'execute': 'qom-set', 'arguments': { 'path':
> %s, "
> > > + "'property': 'temperature', 'value': %d } }", id,
> > > value);
> > > + g_assert(qdict_haskey(response, "return"));
> > > + qobject_unref(response);
> > > +}
> > > +
> > > +/*
> > > + * Compute the temperature using the integer and decimal part and
> return
> > > + * millidegrees. The decimal part are only the top 3 bits so we shift
> it
> > > by
> > > + * 5 here.
> > > + */
> > > +static uint32_t regs_to_temp(uint8_t integer, uint8_t decimal)
> > > +{
> > > + return ((integer << 3) + (decimal >> 5)) *
> TEMP_UNIT_IN_MILLIDEGREE;
> > > +}
> > > +
> > > +/*
> > > + * Compute the integer and decimal parts of the temperature in
> > > millidegrees.
> > > + * H/W store the decimal in the top 3 bits so we shift it by 5.
> > > + */
> > > +static void temp_to_regs(uint32_t temp, uint8_t *integer, uint8_t
> > > *decimal)
> > > +{
> > > + temp /= TEMP_UNIT_IN_MILLIDEGREE;
> > > + *integer = temp >> 3;
> > > + *decimal = (temp & 0x7) << 5;
> > > +}
> > > +
> > > +static void tx_rx(void *obj, void *data, QGuestAllocator *alloc)
> > > +{
> > > + uint16_t value;
> > > + uint8_t integer, decimal;
> > > + QI2CDevice *i2cdev = (QI2CDevice *)obj;
> > > +
> > > + /* Test default values */
> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
> > > + g_assert_cmpuint(value, ==, 0);
> > > +
> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 0);
> > > +
> > > + /* Test setting temperature */
> > > + qmp_sbtsi_set_temperature(TEST_ID, 20000);
> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
> > > + g_assert_cmpuint(value, ==, 20000);
> > > +
> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 20000);
> > > +
> > > + /* Set alert mask in config */
> > > + i2c_set8(i2cdev, REG_CONFIG_WR, CONFIG_ALERT_MASK);
> > > + value = i2c_get8(i2cdev, REG_CONFIG);
> > > + g_assert_cmphex(value, ==, CONFIG_ALERT_MASK);
> > > + /* Enable alarm_en */
> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, ALARM_EN);
> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> > > + g_assert_cmphex(value, ==, ALARM_EN);
> > > +
> > > + /* Test setting limits */
> > > + /* Limit low = 10.500 */
> > > + temp_to_regs(LIMIT_LOW, &integer, &decimal);
> > > + i2c_set8(i2cdev, REG_TEMP_LOW_INT, integer);
> > > + i2c_set8(i2cdev, REG_TEMP_LOW_DEC, decimal);
> > > + integer = i2c_get8(i2cdev, REG_TEMP_LOW_INT);
> > > + decimal = i2c_get8(i2cdev, REG_TEMP_LOW_DEC);
> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_LOW);
> > > + /* Limit high = 55.125 */
> > > + temp_to_regs(LIMIT_HIGH, &integer, &decimal);
> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_INT, integer);
> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_DEC, decimal);
> > > + integer = i2c_get8(i2cdev, REG_TEMP_HIGH_INT);
> > > + decimal = i2c_get8(i2cdev, REG_TEMP_HIGH_DEC);
> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_HIGH);
> > > + /* No alert is generated. */
> > > + value = i2c_get8(i2cdev, REG_STATUS);
> > > + g_assert_cmphex(value, ==, 0);
> > > +
> > > + /* Test alert for low temperature */
> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_LOW);
> > > + value = i2c_get8(i2cdev, REG_STATUS);
> > > + g_assert_cmphex(value, ==, STATUS_LOW_ALERT);
> > > +
> > > + /* Test alert for high temperature */
> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_HIGH);
> > > + value = i2c_get8(i2cdev, REG_STATUS);
> > > + g_assert_cmphex(value, ==, STATUS_HIGH_ALERT);
> > > +
> > > + /* Disable alarm_en */
> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, 0);
> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> > > + g_assert_cmphex(value, ==, 0);
> > > + /* No alert when alarm_en is false. */
> > > + value = i2c_get8(i2cdev, REG_STATUS);
> > > + g_assert_cmphex(value, ==, 0);
> > > +}
> > > +
> > > +static void sbtsi_register_nodes(void)
> > > +{
> > > + QOSGraphEdgeOptions opts = {
> > > + .extra_device_opts = "id=" TEST_ID ",address=0x4c"
> > > + };
> > > + add_qi2c_address(&opts, &(QI2CAddress) { TEST_ADDR });
> > > +
> > > + qos_node_create_driver("sbtsi", i2c_device_create);
> > > + qos_node_consumes("sbtsi", "i2c-bus", &opts);
> > > +
> > > + qos_add_test("tx-rx", "sbtsi", tx_rx, NULL);
> > > +}
> > > +libqos_init(sbtsi_register_nodes);
> > > --
> >
> >
> > + Corey for i2c maintainer. The new sensor directory is mostly if not
> > entirely i2c devices. I didn't create a maintainer entry for this i2c
> > device, but I can if desired and send out a v2.
>
> Yeah, I guess I should be maintainer there. I'll queue up a change for
> that. Thanks.
>
> -corey
>
> >
> >
> > > 2.34.1.575.g55b058a8bb-goog
> > >
> > >
>
[-- Attachment #2: Type: text/html, Size: 35412 bytes --]
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-18 17:10 ` Patrick Venture
@ 2022-01-27 0:09 ` Hao Wu
2022-01-27 14:55 ` Corey Minyard
0 siblings, 1 reply; 15+ messages in thread
From: Hao Wu @ 2022-01-27 0:09 UTC (permalink / raw)
To: Patrick Venture
Cc: Corey Minyard, Thomas Huth, Laurent Vivier, Paolo Bonzini,
QEMU Developers, Doug Evans
[-- Attachment #1: Type: text/plain, Size: 27025 bytes --]
Hi,
Sorry for the late reply. I'm not sure what "auto-increment" means here.
The kernel driver at
https://lkml.org/lkml/2020/12/11/968
only has byte-size read/write operations, so I don't see a problem here.
The values are extracted
from the datasheet.
On Tue, Jan 18, 2022 at 9:10 AM Patrick Venture <venture@google.com> wrote:
>
>
> On Mon, Jan 17, 2022 at 6:05 AM Corey Minyard <cminyard@mvista.com> wrote:
>
>> On Sun, Jan 09, 2022 at 06:17:34PM -0800, Patrick Venture wrote:
>> > On Fri, Jan 7, 2022 at 7:04 PM Patrick Venture <venture@google.com>
>> wrote:
>> >
>> > > From: Hao Wu <wuhaotsh@google.com>
>> > >
>> > > SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
>> > > interface that reports AMD SoC's Ttcl (normalized temperature),
>> > > and resembles a typical 8-pin remote temperature sensor's I2C
>> interface
>> > > to BMC.
>> > >
>> > > This patch implements a basic AMD SB-TSI sensor that is
>> > > compatible with the open-source data sheet from AMD and Linux
>> > > kernel driver.
>> > >
>> > > Reference:
>> > > Linux kernel driver:
>> > > https://lkml.org/lkml/2020/12/11/968
>> > > Register Map:
>> > > https://developer.amd.com/wp-content/resources/56255_3_03.PDF
>> > > (Chapter 6)
>> > >
>> > > Signed-off-by: Hao Wu <wuhaotsh@google.com>
>> > > Reviewed-by: Doug Evans <dje@google.com>
>> > > ---
>> > > hw/sensor/Kconfig | 4 +
>> > > hw/sensor/meson.build | 1 +
>> > > hw/sensor/tmp_sbtsi.c | 393
>> +++++++++++++++++++++++++++++++++++
>> > > hw/sensor/trace-events | 5 +
>> > > hw/sensor/trace.h | 1 +
>> > > meson.build | 1 +
>> > > tests/qtest/meson.build | 1 +
>> > > tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
>> > > 8 files changed, 586 insertions(+)
>> > > create mode 100644 hw/sensor/tmp_sbtsi.c
>> > > create mode 100644 hw/sensor/trace-events
>> > > create mode 100644 hw/sensor/trace.h
>> > > create mode 100644 tests/qtest/tmp_sbtsi-test.c
>> > >
>> > > diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
>> > > index 9c8a049b06..27f6f79c84 100644
>> > > --- a/hw/sensor/Kconfig
>> > > +++ b/hw/sensor/Kconfig
>> > > @@ -21,3 +21,7 @@ config ADM1272
>> > > config MAX34451
>> > > bool
>> > > depends on I2C
>> > > +
>> > > +config AMDSBTSI
>> > > + bool
>> > > + depends on I2C
>> > > diff --git a/hw/sensor/meson.build b/hw/sensor/meson.build
>> > > index 059c4ca935..f7b0e645eb 100644
>> > > --- a/hw/sensor/meson.build
>> > > +++ b/hw/sensor/meson.build
>> > > @@ -4,3 +4,4 @@ softmmu_ss.add(when: 'CONFIG_DPS310', if_true:
>> > > files('dps310.c'))
>> > > softmmu_ss.add(when: 'CONFIG_EMC141X', if_true: files('emc141x.c'))
>> > > softmmu_ss.add(when: 'CONFIG_ADM1272', if_true: files('adm1272.c'))
>> > > softmmu_ss.add(when: 'CONFIG_MAX34451', if_true: files('max34451.c'))
>> > > +softmmu_ss.add(when: 'CONFIG_AMDSBTSI', if_true:
>> files('tmp_sbtsi.c'))
>> > > diff --git a/hw/sensor/tmp_sbtsi.c b/hw/sensor/tmp_sbtsi.c
>> > > new file mode 100644
>> > > index 0000000000..b68c7ebf61
>> > > --- /dev/null
>> > > +++ b/hw/sensor/tmp_sbtsi.c
>> > > @@ -0,0 +1,393 @@
>> > > +/*
>> > > + * AMD SBI Temperature Sensor Interface (SB-TSI)
>> > > + *
>> > > + * Copyright 2021 Google LLC
>> > > + *
>> > > + * This program is free software; you can redistribute it and/or
>> modify it
>> > > + * under the terms of the GNU General Public License as published by
>> the
>> > > + * Free Software Foundation; either version 2 of the License, or
>> > > + * (at your option) any later version.
>> > > + *
>> > > + * This program is distributed in the hope that it will be useful,
>> but
>> > > WITHOUT
>> > > + * ANY WARRANTY; without even the implied warranty of
>> MERCHANTABILITY or
>> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
>> License
>> > > + * for more details.
>> > > + */
>> > > +
>> > > +#include "qemu/osdep.h"
>> > > +#include "hw/i2c/smbus_slave.h"
>> > > +#include "hw/irq.h"
>> > > +#include "migration/vmstate.h"
>> > > +#include "qapi/error.h"
>> > > +#include "qapi/visitor.h"
>> > > +#include "qemu/log.h"
>> > > +#include "qemu/module.h"
>> > > +#include "trace.h"
>> > > +
>> > > +#define TYPE_SBTSI "sbtsi"
>> > > +#define SBTSI(obj) OBJECT_CHECK(SBTSIState, (obj), TYPE_SBTSI)
>> > > +
>> > > +/**
>> > > + * SBTSIState:
>> > > + * temperatures are in units of 0.125 degrees
>> > > + * @temperature: Temperature
>> > > + * @limit_low: Lowest temperature
>> > > + * @limit_high: Highest temperature
>> > > + * @status: The status register
>> > > + * @config: The config register
>> > > + * @alert_config: The config for alarm_l output.
>> > > + * @addr: The address to read/write for the next cmd.
>> > > + * @alarm: The alarm_l output pin (GPIO)
>> > > + */
>> > > +typedef struct SBTSIState {
>> > > + SMBusDevice parent;
>> > > +
>> > > + uint32_t temperature;
>> > > + uint32_t limit_low;
>> > > + uint32_t limit_high;
>> > > + uint8_t status;
>> > > + uint8_t config;
>> > > + uint8_t alert_config;
>> > > + uint8_t addr;
>> > > + qemu_irq alarm;
>> > > +} SBTSIState;
>> > > +
>> > > +/*
>> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
>> registers
>> > > are
>> > > + * the integer part of a temperature value or limit, and "_DEC"
>> registers
>> > > are
>> > > + * corresponding decimal parts.
>> > > + */
>> > > +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
>> > > +#define SBTSI_REG_STATUS 0x02 /* RO */
>> > > +#define SBTSI_REG_CONFIG 0x03 /* RO */
>> > > +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
>> > > +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
>> > > +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
>> > > +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
>> > > +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
>> > > +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
>> > > +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
>> > > +#define SBTSI_REG_MAN 0xFE /* RO */
>> > > +#define SBTSI_REG_REV 0xFF /* RO */
>> > > +
>> > > +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
>> > > +#define SBTSI_STATUS_LOW_ALERT BIT(3)
>> > > +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
>> > > +#define SBTSI_ALARM_EN BIT(0)
>> > > +
>> > > +#define SBTSI_LIMIT_LOW_DEFAULT (0)
>> > > +#define SBTSI_LIMIT_HIGH_DEFAULT (560)
>> > > +#define SBTSI_MAN_DEFAULT (0)
>> > > +#define SBTSI_REV_DEFAULT (4)
>> > > +#define SBTSI_ALARM_L "alarm_l"
>> > > +
>> > > +/* The temperature we stored are in units of 0.125 degrees. */
>> > > +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
>> > > +
>> > > +/*
>> > > + * The integer part and decimal of the temperature both 8 bits.
>> > > + * Only the top 3 bits of the decimal parts are used.
>> > > + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875 degrees.
>> > > + */
>> > > +#define SBTSI_TEMP_MAX 255875
>> > > +
>> > > +/* The integer part of the temperature in terms of 0.125 degrees. */
>> > > +static uint8_t get_temp_int(uint32_t temp)
>> > > +{
>> > > + return temp >> 3;
>> > > +}
>> > > +
>> > > +/*
>> > > + * The decimal part of the temperature, in terms of 0.125 degrees.
>> > > + * H/W store it in the top 3 bits so we shift it by 5.
>> > > + */
>> > > +static uint8_t get_temp_dec(uint32_t temp)
>> > > +{
>> > > + return (temp & 0x7) << 5;
>> > > +}
>> > > +
>> > > +/*
>> > > + * Compute the temperature using the integer and decimal part,
>> > > + * in terms of 0.125 degrees. The decimal part are only the top 3
>> bits
>> > > + * so we shift it by 5 here.
>> > > + */
>> > > +static uint32_t compute_temp(uint8_t integer, uint8_t decimal)
>> > > +{
>> > > + return (integer << 3) + (decimal >> 5);
>> > > +}
>> > > +
>> > > +/* Compute new temp with new int part of the temperature. */
>> > > +static uint32_t compute_temp_int(uint32_t temp, uint8_t integer)
>> > > +{
>> > > + return compute_temp(integer, get_temp_dec(temp));
>> > > +}
>> > > +
>> > > +/* Compute new temp with new dec part of the temperature. */
>> > > +static uint32_t compute_temp_dec(uint32_t temp, uint8_t decimal)
>> > > +{
>> > > + return compute_temp(get_temp_int(temp), decimal);
>> > > +}
>> > > +
>> > > +/* The integer part of the temperature. */
>> > > +static void sbtsi_update_status(SBTSIState *s)
>> > > +{
>> > > + s->status = 0;
>> > > + if (s->alert_config & SBTSI_ALARM_EN) {
>> > > + if (s->temperature >= s->limit_high) {
>> > > + s->status |= SBTSI_STATUS_HIGH_ALERT;
>> > > + }
>> > > + if (s->temperature <= s->limit_low) {
>> > > + s->status |= SBTSI_STATUS_LOW_ALERT;
>> > > + }
>> > > + }
>> > > +}
>> > > +
>> > > +static void sbtsi_update_alarm(SBTSIState *s)
>> > > +{
>> > > + sbtsi_update_status(s);
>> > > + if (s->status != 0 && !(s->config & SBTSI_CONFIG_ALERT_MASK)) {
>> > > + qemu_irq_raise(s->alarm);
>> > > + } else {
>> > > + qemu_irq_lower(s->alarm);
>> > > + }
>> > > +}
>> > > +
>> > > +static uint8_t sbtsi_read_byte(SMBusDevice *d)
>> > > +{
>> > > + SBTSIState *s = SBTSI(d);
>> > > + uint8_t data = 0;
>> > > +
>> > > + switch (s->addr) {
>> > > + case SBTSI_REG_TEMP_INT:
>> > > + data = get_temp_int(s->temperature);
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_TEMP_DEC:
>> > > + data = get_temp_dec(s->temperature);
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_TEMP_HIGH_INT:
>> > > + data = get_temp_int(s->limit_high);
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_TEMP_LOW_INT:
>> > > + data = get_temp_int(s->limit_low);
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_TEMP_HIGH_DEC:
>> > > + data = get_temp_dec(s->limit_high);
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_TEMP_LOW_DEC:
>> > > + data = get_temp_dec(s->limit_low);
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_CONFIG:
>> > > + case SBTSI_REG_CONFIG_WR:
>> > > + data = s->config;
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_STATUS:
>> > > + sbtsi_update_alarm(s);
>> > > + data = s->status;
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_ALERT_CONFIG:
>> > > + data = s->alert_config;
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_MAN:
>> > > + data = SBTSI_MAN_DEFAULT;
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_REV:
>> > > + data = SBTSI_REV_DEFAULT;
>> > > + break;
>>
>> Does this device do some sort of auto-increment on the address when
>> reading/writing?
>>
>
> +Hao Wu <wuhaotsh@google.com> - Please take a look at the above
> question. I imagine it's a while since you've thought about it, but please
> double check :)
> Thanks!
>
>
>> Other than that possible issue, I don't see anything else, it's pretty
>> straightforward.
>>
>> > > +
>> > > + default:
>> > > + qemu_log_mask(LOG_GUEST_ERROR,
>> > > + "%s: reading from invalid reg: 0x%02x\n",
>> > > + __func__, s->addr);
>> > > + break;
>> > > + }
>> > > +
>> > > + trace_tmp_sbtsi_read_data(s->addr, data);
>> > > + return data;
>> > > +}
>> > > +
>> > > +static void sbtsi_write(SBTSIState *s, uint8_t data)
>> > > +{
>> > > + trace_tmp_sbtsi_write_data(s->addr, data);
>> > > + switch (s->addr) {
>> > > + case SBTSI_REG_CONFIG_WR:
>> > > + s->config = data;
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_TEMP_HIGH_INT:
>> > > + s->limit_high = compute_temp_int(s->limit_high, data);
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_TEMP_LOW_INT:
>> > > + s->limit_low = compute_temp_int(s->limit_low, data);
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_TEMP_HIGH_DEC:
>> > > + s->limit_high = compute_temp_dec(s->limit_high, data);
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_TEMP_LOW_DEC:
>> > > + s->limit_low = compute_temp_dec(s->limit_low, data);
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_ALERT_CONFIG:
>> > > + s->alert_config = data;
>> > > + break;
>> > > +
>> > > + case SBTSI_REG_TEMP_INT:
>> > > + case SBTSI_REG_TEMP_DEC:
>> > > + case SBTSI_REG_CONFIG:
>> > > + case SBTSI_REG_STATUS:
>> > > + case SBTSI_REG_MAN:
>> > > + case SBTSI_REG_REV:
>> > > + qemu_log_mask(LOG_GUEST_ERROR,
>> > > + "%s: writing to read only reg: 0x%02x data:
>> 0x%02x\n",
>> > > + __func__, s->addr, data);
>> > > + break;
>> > > +
>> > > + default:
>> > > + qemu_log_mask(LOG_GUEST_ERROR,
>> > > + "%s: writing to invalid reg: 0x%02x data: 0x%02x\n",
>> > > + __func__, s->addr, data);
>> > > + break;
>> > > + }
>> > > + sbtsi_update_alarm(s);
>> > > +}
>> > > +
>> > > +static int sbtsi_write_data(SMBusDevice *d, uint8_t *buf, uint8_t
>> len)
>> > > +{
>> > > + SBTSIState *s = SBTSI(d);
>> > > +
>> > > + if (len == 0) {
>> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: writing empty data\n",
>> > > __func__);
>> > > + return -1;
>> > > + }
>> > > +
>> > > + s->addr = buf[0];
>> > > + if (len > 1) {
>> > > + sbtsi_write(s, buf[1]);
>> > > + if (len > 2) {
>> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: extra data at end\n",
>> > > __func__);
>> > > + }
>> > > + }
>> > > + return 0;
>> > > +}
>> > > +
>> > > +/* Units are millidegrees. */
>> > > +static void sbtsi_get_temperature(Object *obj, Visitor *v, const char
>> > > *name,
>> > > + void *opaque, Error **errp)
>> > > +{
>> > > + SBTSIState *s = SBTSI(obj);
>> > > + uint32_t temp = s->temperature * SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
>> > > +
>> > > + visit_type_uint32(v, name, &temp, errp);
>> > > +}
>> > > +
>> > > +/* Units are millidegrees. */
>> > > +static void sbtsi_set_temperature(Object *obj, Visitor *v, const char
>> > > *name,
>> > > + void *opaque, Error **errp)
>> > > +{
>> > > + SBTSIState *s = SBTSI(obj);
>> > > + uint32_t temp;
>> > > +
>> > > + if (!visit_type_uint32(v, name, &temp, errp)) {
>> > > + return;
>> > > + }
>> > > + if (temp > SBTSI_TEMP_MAX) {
>> > > + error_setg(errp, "value %" PRIu32 ".%03" PRIu32 " C is out of
>> > > range",
>> > > + temp / 1000, temp % 1000);
>> > > + return;
>> > > + }
>> > > +
>> > > + s->temperature = temp / SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
>> > > + sbtsi_update_alarm(s);
>> > > +}
>> > > +
>> > > +static int sbtsi_post_load(void *opaque, int version_id)
>> > > +{
>> > > + SBTSIState *s = opaque;
>> > > +
>> > > + sbtsi_update_alarm(s);
>> > > + return 0;
>> > > +}
>> > > +
>> > > +static const VMStateDescription vmstate_sbtsi = {
>> > > + .name = "SBTSI",
>> > > + .version_id = 0,
>> > > + .minimum_version_id = 0,
>> > > + .post_load = sbtsi_post_load,
>> > > + .fields = (VMStateField[]) {
>> > > + VMSTATE_UINT32(temperature, SBTSIState),
>> > > + VMSTATE_UINT32(limit_low, SBTSIState),
>> > > + VMSTATE_UINT32(limit_high, SBTSIState),
>> > > + VMSTATE_UINT8(config, SBTSIState),
>> > > + VMSTATE_UINT8(status, SBTSIState),
>> > > + VMSTATE_UINT8(addr, SBTSIState),
>> > > + VMSTATE_END_OF_LIST()
>> > > + }
>> > > +};
>> > > +
>> > > +static void sbtsi_enter_reset(Object *obj, ResetType type)
>> > > +{
>> > > + SBTSIState *s = SBTSI(obj);
>> > > +
>> > > + s->config = 0;
>> > > + s->limit_low = SBTSI_LIMIT_LOW_DEFAULT;
>> > > + s->limit_high = SBTSI_LIMIT_HIGH_DEFAULT;
>> > > +}
>> > > +
>> > > +static void sbtsi_hold_reset(Object *obj)
>> > > +{
>> > > + SBTSIState *s = SBTSI(obj);
>> > > +
>> > > + qemu_irq_lower(s->alarm);
>> > > +}
>> > > +
>> > > +static void sbtsi_init(Object *obj)
>> > > +{
>> > > + SBTSIState *s = SBTSI(obj);
>> > > +
>> > > + /* Current temperature in millidegrees. */
>> > > + object_property_add(obj, "temperature", "uint32",
>> > > + sbtsi_get_temperature, sbtsi_set_temperature,
>> > > + NULL, NULL);
>> > > + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm, SBTSI_ALARM_L,
>> 0);
>> > > +}
>> > > +
>> > > +static void sbtsi_class_init(ObjectClass *klass, void *data)
>> > > +{
>> > > + ResettableClass *rc = RESETTABLE_CLASS(klass);
>> > > + DeviceClass *dc = DEVICE_CLASS(klass);
>> > > + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
>> > > +
>> > > + dc->desc = "SB-TSI Temperature Sensor";
>> > > + dc->vmsd = &vmstate_sbtsi;
>> > > + k->write_data = sbtsi_write_data;
>> > > + k->receive_byte = sbtsi_read_byte;
>> > > + rc->phases.enter = sbtsi_enter_reset;
>> > > + rc->phases.hold = sbtsi_hold_reset;
>> > > +}
>> > > +
>> > > +static const TypeInfo sbtsi_info = {
>> > > + .name = TYPE_SBTSI,
>> > > + .parent = TYPE_SMBUS_DEVICE,
>> > > + .instance_size = sizeof(SBTSIState),
>> > > + .instance_init = sbtsi_init,
>> > > + .class_init = sbtsi_class_init,
>> > > +};
>> > > +
>> > > +static void sbtsi_register_types(void)
>> > > +{
>> > > + type_register_static(&sbtsi_info);
>> > > +}
>> > > +
>> > > +type_init(sbtsi_register_types)
>> > > diff --git a/hw/sensor/trace-events b/hw/sensor/trace-events
>> > > new file mode 100644
>> > > index 0000000000..21ab3809e2
>> > > --- /dev/null
>> > > +++ b/hw/sensor/trace-events
>> > > @@ -0,0 +1,5 @@
>> > > +# See docs/devel/tracing.rst for syntax documentation.
>> > > +
>> > > +# tmp_sbtsi.c
>> > > +tmp_sbtsi_write_data(uint8_t addr, uint8_t value) "SBTSI write
>> > > addr:0x%02x data: 0x%02x"
>> > > +tmp_sbtsi_read_data(uint8_t addr, uint8_t value) "SBTSI read
>> addr:0x%02x
>> > > data: 0x%02x"
>> > > diff --git a/hw/sensor/trace.h b/hw/sensor/trace.h
>> > > new file mode 100644
>> > > index 0000000000..e4721560b0
>> > > --- /dev/null
>> > > +++ b/hw/sensor/trace.h
>> > > @@ -0,0 +1 @@
>> > > +#include "trace/trace-hw_sensor.h"
>> > > diff --git a/meson.build b/meson.build
>> > > index 53065e96ec..f8ab0bf74e 100644
>> > > --- a/meson.build
>> > > +++ b/meson.build
>> > > @@ -2494,6 +2494,7 @@ if have_system
>> > > 'hw/rtc',
>> > > 'hw/s390x',
>> > > 'hw/scsi',
>> > > + 'hw/sensor',
>> > > 'hw/sd',
>> > > 'hw/sh4',
>> > > 'hw/sparc',
>> > > diff --git a/tests/qtest/meson.build b/tests/qtest/meson.build
>> > > index 37e1eaa449..d1a8c38f74 100644
>> > > --- a/tests/qtest/meson.build
>> > > +++ b/tests/qtest/meson.build
>> > > @@ -254,6 +254,7 @@ qos_test_ss.add(
>> > > 'spapr-phb-test.c',
>> > > 'tmp105-test.c',
>> > > 'emc141x-test.c',
>> > > + 'tmp_sbtsi-test.c',
>> > > 'usb-hcd-ohci-test.c',
>> > > 'virtio-test.c',
>> > > 'virtio-blk-test.c',
>> > > diff --git a/tests/qtest/tmp_sbtsi-test.c
>> b/tests/qtest/tmp_sbtsi-test.c
>> > > new file mode 100644
>> > > index 0000000000..7f5fafacc7
>> > > --- /dev/null
>> > > +++ b/tests/qtest/tmp_sbtsi-test.c
>> > > @@ -0,0 +1,180 @@
>> > > +/*
>> > > + * QTests for the SBTSI temperature sensor
>> > > + *
>> > > + * Copyright 2020 Google LLC
>> > > + *
>> > > + * This program is free software; you can redistribute it and/or
>> modify it
>> > > + * under the terms of the GNU General Public License as published by
>> the
>> > > + * Free Software Foundation; either version 2 of the License, or
>> > > + * (at your option) any later version.
>> > > + *
>> > > + * This program is distributed in the hope that it will be useful,
>> but
>> > > WITHOUT
>> > > + * ANY WARRANTY; without even the implied warranty of
>> MERCHANTABILITY or
>> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
>> License
>> > > + * for more details.
>> > > + */
>> > > +
>> > > +#include "qemu/osdep.h"
>> > > +
>> > > +#include "libqtest-single.h"
>> > > +#include "libqos/qgraph.h"
>> > > +#include "libqos/i2c.h"
>> > > +#include "qapi/qmp/qdict.h"
>> > > +#include "qemu/bitops.h"
>> > > +
>> > > +#define TEST_ID "sbtsi-test"
>> > > +#define TEST_ADDR (0x4c)
>> > > +
>> > > +/*
>> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
>> registers
>> > > are
>> > > + * the integer part of a temperature value or limit, and "_DEC"
>> registers
>> > > are
>> > > + * corresponding decimal parts.
>> > > + */
>> > > +#define REG_TEMP_INT 0x01 /* RO */
>> > > +#define REG_STATUS 0x02 /* RO */
>> > > +#define REG_CONFIG 0x03 /* RO */
>> > > +#define REG_TEMP_HIGH_INT 0x07 /* RW */
>> > > +#define REG_TEMP_LOW_INT 0x08 /* RW */
>> > > +#define REG_CONFIG_WR 0x09 /* RW */
>> > > +#define REG_TEMP_DEC 0x10 /* RO */
>> > > +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
>> > > +#define REG_TEMP_LOW_DEC 0x14 /* RW */
>> > > +#define REG_ALERT_CONFIG 0xBF /* RW */
>> > > +
>> > > +#define STATUS_HIGH_ALERT BIT(4)
>> > > +#define STATUS_LOW_ALERT BIT(3)
>> > > +#define CONFIG_ALERT_MASK BIT(7)
>> > > +#define ALARM_EN BIT(0)
>> > > +
>> > > +/* The temperature stored are in units of 0.125 degrees. */
>> > > +#define TEMP_UNIT_IN_MILLIDEGREE 125
>> > > +#define LIMIT_LOW (10500)
>> > > +#define LIMIT_HIGH (55125)
>> > > +
>> > > +static uint32_t qmp_sbtsi_get_temperature(const char *id)
>> > > +{
>> > > + QDict *response;
>> > > + int ret;
>> > > +
>> > > + response = qmp("{ 'execute': 'qom-get', 'arguments': { 'path':
>> %s, "
>> > > + "'property': 'temperature' } }", id);
>> > > + g_assert(qdict_haskey(response, "return"));
>> > > + ret = (uint32_t)qdict_get_int(response, "return");
>> > > + qobject_unref(response);
>> > > + return ret;
>> > > +}
>> > > +
>> > > +static void qmp_sbtsi_set_temperature(const char *id, uint32_t value)
>> > > +{
>> > > + QDict *response;
>> > > +
>> > > + response = qmp("{ 'execute': 'qom-set', 'arguments': { 'path':
>> %s, "
>> > > + "'property': 'temperature', 'value': %d } }", id,
>> > > value);
>> > > + g_assert(qdict_haskey(response, "return"));
>> > > + qobject_unref(response);
>> > > +}
>> > > +
>> > > +/*
>> > > + * Compute the temperature using the integer and decimal part and
>> return
>> > > + * millidegrees. The decimal part are only the top 3 bits so we
>> shift it
>> > > by
>> > > + * 5 here.
>> > > + */
>> > > +static uint32_t regs_to_temp(uint8_t integer, uint8_t decimal)
>> > > +{
>> > > + return ((integer << 3) + (decimal >> 5)) *
>> TEMP_UNIT_IN_MILLIDEGREE;
>> > > +}
>> > > +
>> > > +/*
>> > > + * Compute the integer and decimal parts of the temperature in
>> > > millidegrees.
>> > > + * H/W store the decimal in the top 3 bits so we shift it by 5.
>> > > + */
>> > > +static void temp_to_regs(uint32_t temp, uint8_t *integer, uint8_t
>> > > *decimal)
>> > > +{
>> > > + temp /= TEMP_UNIT_IN_MILLIDEGREE;
>> > > + *integer = temp >> 3;
>> > > + *decimal = (temp & 0x7) << 5;
>> > > +}
>> > > +
>> > > +static void tx_rx(void *obj, void *data, QGuestAllocator *alloc)
>> > > +{
>> > > + uint16_t value;
>> > > + uint8_t integer, decimal;
>> > > + QI2CDevice *i2cdev = (QI2CDevice *)obj;
>> > > +
>> > > + /* Test default values */
>> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
>> > > + g_assert_cmpuint(value, ==, 0);
>> > > +
>> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
>> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
>> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 0);
>> > > +
>> > > + /* Test setting temperature */
>> > > + qmp_sbtsi_set_temperature(TEST_ID, 20000);
>> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
>> > > + g_assert_cmpuint(value, ==, 20000);
>> > > +
>> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
>> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
>> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 20000);
>> > > +
>> > > + /* Set alert mask in config */
>> > > + i2c_set8(i2cdev, REG_CONFIG_WR, CONFIG_ALERT_MASK);
>> > > + value = i2c_get8(i2cdev, REG_CONFIG);
>> > > + g_assert_cmphex(value, ==, CONFIG_ALERT_MASK);
>> > > + /* Enable alarm_en */
>> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, ALARM_EN);
>> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
>> > > + g_assert_cmphex(value, ==, ALARM_EN);
>> > > +
>> > > + /* Test setting limits */
>> > > + /* Limit low = 10.500 */
>> > > + temp_to_regs(LIMIT_LOW, &integer, &decimal);
>> > > + i2c_set8(i2cdev, REG_TEMP_LOW_INT, integer);
>> > > + i2c_set8(i2cdev, REG_TEMP_LOW_DEC, decimal);
>> > > + integer = i2c_get8(i2cdev, REG_TEMP_LOW_INT);
>> > > + decimal = i2c_get8(i2cdev, REG_TEMP_LOW_DEC);
>> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_LOW);
>> > > + /* Limit high = 55.125 */
>> > > + temp_to_regs(LIMIT_HIGH, &integer, &decimal);
>> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_INT, integer);
>> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_DEC, decimal);
>> > > + integer = i2c_get8(i2cdev, REG_TEMP_HIGH_INT);
>> > > + decimal = i2c_get8(i2cdev, REG_TEMP_HIGH_DEC);
>> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_HIGH);
>> > > + /* No alert is generated. */
>> > > + value = i2c_get8(i2cdev, REG_STATUS);
>> > > + g_assert_cmphex(value, ==, 0);
>> > > +
>> > > + /* Test alert for low temperature */
>> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_LOW);
>> > > + value = i2c_get8(i2cdev, REG_STATUS);
>> > > + g_assert_cmphex(value, ==, STATUS_LOW_ALERT);
>> > > +
>> > > + /* Test alert for high temperature */
>> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_HIGH);
>> > > + value = i2c_get8(i2cdev, REG_STATUS);
>> > > + g_assert_cmphex(value, ==, STATUS_HIGH_ALERT);
>> > > +
>> > > + /* Disable alarm_en */
>> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, 0);
>> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
>> > > + g_assert_cmphex(value, ==, 0);
>> > > + /* No alert when alarm_en is false. */
>> > > + value = i2c_get8(i2cdev, REG_STATUS);
>> > > + g_assert_cmphex(value, ==, 0);
>> > > +}
>> > > +
>> > > +static void sbtsi_register_nodes(void)
>> > > +{
>> > > + QOSGraphEdgeOptions opts = {
>> > > + .extra_device_opts = "id=" TEST_ID ",address=0x4c"
>> > > + };
>> > > + add_qi2c_address(&opts, &(QI2CAddress) { TEST_ADDR });
>> > > +
>> > > + qos_node_create_driver("sbtsi", i2c_device_create);
>> > > + qos_node_consumes("sbtsi", "i2c-bus", &opts);
>> > > +
>> > > + qos_add_test("tx-rx", "sbtsi", tx_rx, NULL);
>> > > +}
>> > > +libqos_init(sbtsi_register_nodes);
>> > > --
>> >
>> >
>> > + Corey for i2c maintainer. The new sensor directory is mostly if not
>> > entirely i2c devices. I didn't create a maintainer entry for this i2c
>> > device, but I can if desired and send out a v2.
>>
>> Yeah, I guess I should be maintainer there. I'll queue up a change for
>> that. Thanks.
>>
>> -corey
>>
>> >
>> >
>> > > 2.34.1.575.g55b058a8bb-goog
>> > >
>> > >
>>
>
[-- Attachment #2: Type: text/html, Size: 36196 bytes --]
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-27 0:09 ` Hao Wu
@ 2022-01-27 14:55 ` Corey Minyard
2022-01-27 18:19 ` Hao Wu
0 siblings, 1 reply; 15+ messages in thread
From: Corey Minyard @ 2022-01-27 14:55 UTC (permalink / raw)
To: Hao Wu
Cc: Laurent Vivier, Thomas Huth, Patrick Venture, QEMU Developers,
Doug Evans, Paolo Bonzini
On Wed, Jan 26, 2022 at 04:09:03PM -0800, Hao Wu wrote:
> Hi,
>
> Sorry for the late reply. I'm not sure what "auto-increment" means here.
The question is: When a value is read, does the address automatically
increment. I2C devices very often do this. If you do a multi-byte
read, they often will read the value from address 0, then from address
1, etc. Same for writes.
> The kernel driver at
> https://lkml.org/lkml/2020/12/11/968
> only has byte-size read/write operations, so I don't see a problem here.
> The values are extracted
> from the datasheet.
The *Linux* kernel driver my only do byte-size operations, but other
kernels may work different, and the Linux kernel may change. You have
to implement from the datasheet, not the device driver.
Thanks,
-corey
>
> On Tue, Jan 18, 2022 at 9:10 AM Patrick Venture <venture@google.com> wrote:
>
> >
> >
> > On Mon, Jan 17, 2022 at 6:05 AM Corey Minyard <cminyard@mvista.com> wrote:
> >
> >> On Sun, Jan 09, 2022 at 06:17:34PM -0800, Patrick Venture wrote:
> >> > On Fri, Jan 7, 2022 at 7:04 PM Patrick Venture <venture@google.com>
> >> wrote:
> >> >
> >> > > From: Hao Wu <wuhaotsh@google.com>
> >> > >
> >> > > SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
> >> > > interface that reports AMD SoC's Ttcl (normalized temperature),
> >> > > and resembles a typical 8-pin remote temperature sensor's I2C
> >> interface
> >> > > to BMC.
> >> > >
> >> > > This patch implements a basic AMD SB-TSI sensor that is
> >> > > compatible with the open-source data sheet from AMD and Linux
> >> > > kernel driver.
> >> > >
> >> > > Reference:
> >> > > Linux kernel driver:
> >> > > https://lkml.org/lkml/2020/12/11/968
> >> > > Register Map:
> >> > > https://developer.amd.com/wp-content/resources/56255_3_03.PDF
> >> > > (Chapter 6)
> >> > >
> >> > > Signed-off-by: Hao Wu <wuhaotsh@google.com>
> >> > > Reviewed-by: Doug Evans <dje@google.com>
> >> > > ---
> >> > > hw/sensor/Kconfig | 4 +
> >> > > hw/sensor/meson.build | 1 +
> >> > > hw/sensor/tmp_sbtsi.c | 393
> >> +++++++++++++++++++++++++++++++++++
> >> > > hw/sensor/trace-events | 5 +
> >> > > hw/sensor/trace.h | 1 +
> >> > > meson.build | 1 +
> >> > > tests/qtest/meson.build | 1 +
> >> > > tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
> >> > > 8 files changed, 586 insertions(+)
> >> > > create mode 100644 hw/sensor/tmp_sbtsi.c
> >> > > create mode 100644 hw/sensor/trace-events
> >> > > create mode 100644 hw/sensor/trace.h
> >> > > create mode 100644 tests/qtest/tmp_sbtsi-test.c
> >> > >
> >> > > diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
> >> > > index 9c8a049b06..27f6f79c84 100644
> >> > > --- a/hw/sensor/Kconfig
> >> > > +++ b/hw/sensor/Kconfig
> >> > > @@ -21,3 +21,7 @@ config ADM1272
> >> > > config MAX34451
> >> > > bool
> >> > > depends on I2C
> >> > > +
> >> > > +config AMDSBTSI
> >> > > + bool
> >> > > + depends on I2C
> >> > > diff --git a/hw/sensor/meson.build b/hw/sensor/meson.build
> >> > > index 059c4ca935..f7b0e645eb 100644
> >> > > --- a/hw/sensor/meson.build
> >> > > +++ b/hw/sensor/meson.build
> >> > > @@ -4,3 +4,4 @@ softmmu_ss.add(when: 'CONFIG_DPS310', if_true:
> >> > > files('dps310.c'))
> >> > > softmmu_ss.add(when: 'CONFIG_EMC141X', if_true: files('emc141x.c'))
> >> > > softmmu_ss.add(when: 'CONFIG_ADM1272', if_true: files('adm1272.c'))
> >> > > softmmu_ss.add(when: 'CONFIG_MAX34451', if_true: files('max34451.c'))
> >> > > +softmmu_ss.add(when: 'CONFIG_AMDSBTSI', if_true:
> >> files('tmp_sbtsi.c'))
> >> > > diff --git a/hw/sensor/tmp_sbtsi.c b/hw/sensor/tmp_sbtsi.c
> >> > > new file mode 100644
> >> > > index 0000000000..b68c7ebf61
> >> > > --- /dev/null
> >> > > +++ b/hw/sensor/tmp_sbtsi.c
> >> > > @@ -0,0 +1,393 @@
> >> > > +/*
> >> > > + * AMD SBI Temperature Sensor Interface (SB-TSI)
> >> > > + *
> >> > > + * Copyright 2021 Google LLC
> >> > > + *
> >> > > + * This program is free software; you can redistribute it and/or
> >> modify it
> >> > > + * under the terms of the GNU General Public License as published by
> >> the
> >> > > + * Free Software Foundation; either version 2 of the License, or
> >> > > + * (at your option) any later version.
> >> > > + *
> >> > > + * This program is distributed in the hope that it will be useful,
> >> but
> >> > > WITHOUT
> >> > > + * ANY WARRANTY; without even the implied warranty of
> >> MERCHANTABILITY or
> >> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> >> License
> >> > > + * for more details.
> >> > > + */
> >> > > +
> >> > > +#include "qemu/osdep.h"
> >> > > +#include "hw/i2c/smbus_slave.h"
> >> > > +#include "hw/irq.h"
> >> > > +#include "migration/vmstate.h"
> >> > > +#include "qapi/error.h"
> >> > > +#include "qapi/visitor.h"
> >> > > +#include "qemu/log.h"
> >> > > +#include "qemu/module.h"
> >> > > +#include "trace.h"
> >> > > +
> >> > > +#define TYPE_SBTSI "sbtsi"
> >> > > +#define SBTSI(obj) OBJECT_CHECK(SBTSIState, (obj), TYPE_SBTSI)
> >> > > +
> >> > > +/**
> >> > > + * SBTSIState:
> >> > > + * temperatures are in units of 0.125 degrees
> >> > > + * @temperature: Temperature
> >> > > + * @limit_low: Lowest temperature
> >> > > + * @limit_high: Highest temperature
> >> > > + * @status: The status register
> >> > > + * @config: The config register
> >> > > + * @alert_config: The config for alarm_l output.
> >> > > + * @addr: The address to read/write for the next cmd.
> >> > > + * @alarm: The alarm_l output pin (GPIO)
> >> > > + */
> >> > > +typedef struct SBTSIState {
> >> > > + SMBusDevice parent;
> >> > > +
> >> > > + uint32_t temperature;
> >> > > + uint32_t limit_low;
> >> > > + uint32_t limit_high;
> >> > > + uint8_t status;
> >> > > + uint8_t config;
> >> > > + uint8_t alert_config;
> >> > > + uint8_t addr;
> >> > > + qemu_irq alarm;
> >> > > +} SBTSIState;
> >> > > +
> >> > > +/*
> >> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
> >> registers
> >> > > are
> >> > > + * the integer part of a temperature value or limit, and "_DEC"
> >> registers
> >> > > are
> >> > > + * corresponding decimal parts.
> >> > > + */
> >> > > +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
> >> > > +#define SBTSI_REG_STATUS 0x02 /* RO */
> >> > > +#define SBTSI_REG_CONFIG 0x03 /* RO */
> >> > > +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
> >> > > +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
> >> > > +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
> >> > > +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
> >> > > +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
> >> > > +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
> >> > > +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
> >> > > +#define SBTSI_REG_MAN 0xFE /* RO */
> >> > > +#define SBTSI_REG_REV 0xFF /* RO */
> >> > > +
> >> > > +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
> >> > > +#define SBTSI_STATUS_LOW_ALERT BIT(3)
> >> > > +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
> >> > > +#define SBTSI_ALARM_EN BIT(0)
> >> > > +
> >> > > +#define SBTSI_LIMIT_LOW_DEFAULT (0)
> >> > > +#define SBTSI_LIMIT_HIGH_DEFAULT (560)
> >> > > +#define SBTSI_MAN_DEFAULT (0)
> >> > > +#define SBTSI_REV_DEFAULT (4)
> >> > > +#define SBTSI_ALARM_L "alarm_l"
> >> > > +
> >> > > +/* The temperature we stored are in units of 0.125 degrees. */
> >> > > +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
> >> > > +
> >> > > +/*
> >> > > + * The integer part and decimal of the temperature both 8 bits.
> >> > > + * Only the top 3 bits of the decimal parts are used.
> >> > > + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875 degrees.
> >> > > + */
> >> > > +#define SBTSI_TEMP_MAX 255875
> >> > > +
> >> > > +/* The integer part of the temperature in terms of 0.125 degrees. */
> >> > > +static uint8_t get_temp_int(uint32_t temp)
> >> > > +{
> >> > > + return temp >> 3;
> >> > > +}
> >> > > +
> >> > > +/*
> >> > > + * The decimal part of the temperature, in terms of 0.125 degrees.
> >> > > + * H/W store it in the top 3 bits so we shift it by 5.
> >> > > + */
> >> > > +static uint8_t get_temp_dec(uint32_t temp)
> >> > > +{
> >> > > + return (temp & 0x7) << 5;
> >> > > +}
> >> > > +
> >> > > +/*
> >> > > + * Compute the temperature using the integer and decimal part,
> >> > > + * in terms of 0.125 degrees. The decimal part are only the top 3
> >> bits
> >> > > + * so we shift it by 5 here.
> >> > > + */
> >> > > +static uint32_t compute_temp(uint8_t integer, uint8_t decimal)
> >> > > +{
> >> > > + return (integer << 3) + (decimal >> 5);
> >> > > +}
> >> > > +
> >> > > +/* Compute new temp with new int part of the temperature. */
> >> > > +static uint32_t compute_temp_int(uint32_t temp, uint8_t integer)
> >> > > +{
> >> > > + return compute_temp(integer, get_temp_dec(temp));
> >> > > +}
> >> > > +
> >> > > +/* Compute new temp with new dec part of the temperature. */
> >> > > +static uint32_t compute_temp_dec(uint32_t temp, uint8_t decimal)
> >> > > +{
> >> > > + return compute_temp(get_temp_int(temp), decimal);
> >> > > +}
> >> > > +
> >> > > +/* The integer part of the temperature. */
> >> > > +static void sbtsi_update_status(SBTSIState *s)
> >> > > +{
> >> > > + s->status = 0;
> >> > > + if (s->alert_config & SBTSI_ALARM_EN) {
> >> > > + if (s->temperature >= s->limit_high) {
> >> > > + s->status |= SBTSI_STATUS_HIGH_ALERT;
> >> > > + }
> >> > > + if (s->temperature <= s->limit_low) {
> >> > > + s->status |= SBTSI_STATUS_LOW_ALERT;
> >> > > + }
> >> > > + }
> >> > > +}
> >> > > +
> >> > > +static void sbtsi_update_alarm(SBTSIState *s)
> >> > > +{
> >> > > + sbtsi_update_status(s);
> >> > > + if (s->status != 0 && !(s->config & SBTSI_CONFIG_ALERT_MASK)) {
> >> > > + qemu_irq_raise(s->alarm);
> >> > > + } else {
> >> > > + qemu_irq_lower(s->alarm);
> >> > > + }
> >> > > +}
> >> > > +
> >> > > +static uint8_t sbtsi_read_byte(SMBusDevice *d)
> >> > > +{
> >> > > + SBTSIState *s = SBTSI(d);
> >> > > + uint8_t data = 0;
> >> > > +
> >> > > + switch (s->addr) {
> >> > > + case SBTSI_REG_TEMP_INT:
> >> > > + data = get_temp_int(s->temperature);
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_TEMP_DEC:
> >> > > + data = get_temp_dec(s->temperature);
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_TEMP_HIGH_INT:
> >> > > + data = get_temp_int(s->limit_high);
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_TEMP_LOW_INT:
> >> > > + data = get_temp_int(s->limit_low);
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_TEMP_HIGH_DEC:
> >> > > + data = get_temp_dec(s->limit_high);
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_TEMP_LOW_DEC:
> >> > > + data = get_temp_dec(s->limit_low);
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_CONFIG:
> >> > > + case SBTSI_REG_CONFIG_WR:
> >> > > + data = s->config;
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_STATUS:
> >> > > + sbtsi_update_alarm(s);
> >> > > + data = s->status;
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_ALERT_CONFIG:
> >> > > + data = s->alert_config;
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_MAN:
> >> > > + data = SBTSI_MAN_DEFAULT;
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_REV:
> >> > > + data = SBTSI_REV_DEFAULT;
> >> > > + break;
> >>
> >> Does this device do some sort of auto-increment on the address when
> >> reading/writing?
> >>
> >
> > +Hao Wu <wuhaotsh@google.com> - Please take a look at the above
> > question. I imagine it's a while since you've thought about it, but please
> > double check :)
> > Thanks!
> >
> >
> >> Other than that possible issue, I don't see anything else, it's pretty
> >> straightforward.
> >>
> >> > > +
> >> > > + default:
> >> > > + qemu_log_mask(LOG_GUEST_ERROR,
> >> > > + "%s: reading from invalid reg: 0x%02x\n",
> >> > > + __func__, s->addr);
> >> > > + break;
> >> > > + }
> >> > > +
> >> > > + trace_tmp_sbtsi_read_data(s->addr, data);
> >> > > + return data;
> >> > > +}
> >> > > +
> >> > > +static void sbtsi_write(SBTSIState *s, uint8_t data)
> >> > > +{
> >> > > + trace_tmp_sbtsi_write_data(s->addr, data);
> >> > > + switch (s->addr) {
> >> > > + case SBTSI_REG_CONFIG_WR:
> >> > > + s->config = data;
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_TEMP_HIGH_INT:
> >> > > + s->limit_high = compute_temp_int(s->limit_high, data);
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_TEMP_LOW_INT:
> >> > > + s->limit_low = compute_temp_int(s->limit_low, data);
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_TEMP_HIGH_DEC:
> >> > > + s->limit_high = compute_temp_dec(s->limit_high, data);
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_TEMP_LOW_DEC:
> >> > > + s->limit_low = compute_temp_dec(s->limit_low, data);
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_ALERT_CONFIG:
> >> > > + s->alert_config = data;
> >> > > + break;
> >> > > +
> >> > > + case SBTSI_REG_TEMP_INT:
> >> > > + case SBTSI_REG_TEMP_DEC:
> >> > > + case SBTSI_REG_CONFIG:
> >> > > + case SBTSI_REG_STATUS:
> >> > > + case SBTSI_REG_MAN:
> >> > > + case SBTSI_REG_REV:
> >> > > + qemu_log_mask(LOG_GUEST_ERROR,
> >> > > + "%s: writing to read only reg: 0x%02x data:
> >> 0x%02x\n",
> >> > > + __func__, s->addr, data);
> >> > > + break;
> >> > > +
> >> > > + default:
> >> > > + qemu_log_mask(LOG_GUEST_ERROR,
> >> > > + "%s: writing to invalid reg: 0x%02x data: 0x%02x\n",
> >> > > + __func__, s->addr, data);
> >> > > + break;
> >> > > + }
> >> > > + sbtsi_update_alarm(s);
> >> > > +}
> >> > > +
> >> > > +static int sbtsi_write_data(SMBusDevice *d, uint8_t *buf, uint8_t
> >> len)
> >> > > +{
> >> > > + SBTSIState *s = SBTSI(d);
> >> > > +
> >> > > + if (len == 0) {
> >> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: writing empty data\n",
> >> > > __func__);
> >> > > + return -1;
> >> > > + }
> >> > > +
> >> > > + s->addr = buf[0];
> >> > > + if (len > 1) {
> >> > > + sbtsi_write(s, buf[1]);
> >> > > + if (len > 2) {
> >> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: extra data at end\n",
> >> > > __func__);
> >> > > + }
> >> > > + }
> >> > > + return 0;
> >> > > +}
> >> > > +
> >> > > +/* Units are millidegrees. */
> >> > > +static void sbtsi_get_temperature(Object *obj, Visitor *v, const char
> >> > > *name,
> >> > > + void *opaque, Error **errp)
> >> > > +{
> >> > > + SBTSIState *s = SBTSI(obj);
> >> > > + uint32_t temp = s->temperature * SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> >> > > +
> >> > > + visit_type_uint32(v, name, &temp, errp);
> >> > > +}
> >> > > +
> >> > > +/* Units are millidegrees. */
> >> > > +static void sbtsi_set_temperature(Object *obj, Visitor *v, const char
> >> > > *name,
> >> > > + void *opaque, Error **errp)
> >> > > +{
> >> > > + SBTSIState *s = SBTSI(obj);
> >> > > + uint32_t temp;
> >> > > +
> >> > > + if (!visit_type_uint32(v, name, &temp, errp)) {
> >> > > + return;
> >> > > + }
> >> > > + if (temp > SBTSI_TEMP_MAX) {
> >> > > + error_setg(errp, "value %" PRIu32 ".%03" PRIu32 " C is out of
> >> > > range",
> >> > > + temp / 1000, temp % 1000);
> >> > > + return;
> >> > > + }
> >> > > +
> >> > > + s->temperature = temp / SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> >> > > + sbtsi_update_alarm(s);
> >> > > +}
> >> > > +
> >> > > +static int sbtsi_post_load(void *opaque, int version_id)
> >> > > +{
> >> > > + SBTSIState *s = opaque;
> >> > > +
> >> > > + sbtsi_update_alarm(s);
> >> > > + return 0;
> >> > > +}
> >> > > +
> >> > > +static const VMStateDescription vmstate_sbtsi = {
> >> > > + .name = "SBTSI",
> >> > > + .version_id = 0,
> >> > > + .minimum_version_id = 0,
> >> > > + .post_load = sbtsi_post_load,
> >> > > + .fields = (VMStateField[]) {
> >> > > + VMSTATE_UINT32(temperature, SBTSIState),
> >> > > + VMSTATE_UINT32(limit_low, SBTSIState),
> >> > > + VMSTATE_UINT32(limit_high, SBTSIState),
> >> > > + VMSTATE_UINT8(config, SBTSIState),
> >> > > + VMSTATE_UINT8(status, SBTSIState),
> >> > > + VMSTATE_UINT8(addr, SBTSIState),
> >> > > + VMSTATE_END_OF_LIST()
> >> > > + }
> >> > > +};
> >> > > +
> >> > > +static void sbtsi_enter_reset(Object *obj, ResetType type)
> >> > > +{
> >> > > + SBTSIState *s = SBTSI(obj);
> >> > > +
> >> > > + s->config = 0;
> >> > > + s->limit_low = SBTSI_LIMIT_LOW_DEFAULT;
> >> > > + s->limit_high = SBTSI_LIMIT_HIGH_DEFAULT;
> >> > > +}
> >> > > +
> >> > > +static void sbtsi_hold_reset(Object *obj)
> >> > > +{
> >> > > + SBTSIState *s = SBTSI(obj);
> >> > > +
> >> > > + qemu_irq_lower(s->alarm);
> >> > > +}
> >> > > +
> >> > > +static void sbtsi_init(Object *obj)
> >> > > +{
> >> > > + SBTSIState *s = SBTSI(obj);
> >> > > +
> >> > > + /* Current temperature in millidegrees. */
> >> > > + object_property_add(obj, "temperature", "uint32",
> >> > > + sbtsi_get_temperature, sbtsi_set_temperature,
> >> > > + NULL, NULL);
> >> > > + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm, SBTSI_ALARM_L,
> >> 0);
> >> > > +}
> >> > > +
> >> > > +static void sbtsi_class_init(ObjectClass *klass, void *data)
> >> > > +{
> >> > > + ResettableClass *rc = RESETTABLE_CLASS(klass);
> >> > > + DeviceClass *dc = DEVICE_CLASS(klass);
> >> > > + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
> >> > > +
> >> > > + dc->desc = "SB-TSI Temperature Sensor";
> >> > > + dc->vmsd = &vmstate_sbtsi;
> >> > > + k->write_data = sbtsi_write_data;
> >> > > + k->receive_byte = sbtsi_read_byte;
> >> > > + rc->phases.enter = sbtsi_enter_reset;
> >> > > + rc->phases.hold = sbtsi_hold_reset;
> >> > > +}
> >> > > +
> >> > > +static const TypeInfo sbtsi_info = {
> >> > > + .name = TYPE_SBTSI,
> >> > > + .parent = TYPE_SMBUS_DEVICE,
> >> > > + .instance_size = sizeof(SBTSIState),
> >> > > + .instance_init = sbtsi_init,
> >> > > + .class_init = sbtsi_class_init,
> >> > > +};
> >> > > +
> >> > > +static void sbtsi_register_types(void)
> >> > > +{
> >> > > + type_register_static(&sbtsi_info);
> >> > > +}
> >> > > +
> >> > > +type_init(sbtsi_register_types)
> >> > > diff --git a/hw/sensor/trace-events b/hw/sensor/trace-events
> >> > > new file mode 100644
> >> > > index 0000000000..21ab3809e2
> >> > > --- /dev/null
> >> > > +++ b/hw/sensor/trace-events
> >> > > @@ -0,0 +1,5 @@
> >> > > +# See docs/devel/tracing.rst for syntax documentation.
> >> > > +
> >> > > +# tmp_sbtsi.c
> >> > > +tmp_sbtsi_write_data(uint8_t addr, uint8_t value) "SBTSI write
> >> > > addr:0x%02x data: 0x%02x"
> >> > > +tmp_sbtsi_read_data(uint8_t addr, uint8_t value) "SBTSI read
> >> addr:0x%02x
> >> > > data: 0x%02x"
> >> > > diff --git a/hw/sensor/trace.h b/hw/sensor/trace.h
> >> > > new file mode 100644
> >> > > index 0000000000..e4721560b0
> >> > > --- /dev/null
> >> > > +++ b/hw/sensor/trace.h
> >> > > @@ -0,0 +1 @@
> >> > > +#include "trace/trace-hw_sensor.h"
> >> > > diff --git a/meson.build b/meson.build
> >> > > index 53065e96ec..f8ab0bf74e 100644
> >> > > --- a/meson.build
> >> > > +++ b/meson.build
> >> > > @@ -2494,6 +2494,7 @@ if have_system
> >> > > 'hw/rtc',
> >> > > 'hw/s390x',
> >> > > 'hw/scsi',
> >> > > + 'hw/sensor',
> >> > > 'hw/sd',
> >> > > 'hw/sh4',
> >> > > 'hw/sparc',
> >> > > diff --git a/tests/qtest/meson.build b/tests/qtest/meson.build
> >> > > index 37e1eaa449..d1a8c38f74 100644
> >> > > --- a/tests/qtest/meson.build
> >> > > +++ b/tests/qtest/meson.build
> >> > > @@ -254,6 +254,7 @@ qos_test_ss.add(
> >> > > 'spapr-phb-test.c',
> >> > > 'tmp105-test.c',
> >> > > 'emc141x-test.c',
> >> > > + 'tmp_sbtsi-test.c',
> >> > > 'usb-hcd-ohci-test.c',
> >> > > 'virtio-test.c',
> >> > > 'virtio-blk-test.c',
> >> > > diff --git a/tests/qtest/tmp_sbtsi-test.c
> >> b/tests/qtest/tmp_sbtsi-test.c
> >> > > new file mode 100644
> >> > > index 0000000000..7f5fafacc7
> >> > > --- /dev/null
> >> > > +++ b/tests/qtest/tmp_sbtsi-test.c
> >> > > @@ -0,0 +1,180 @@
> >> > > +/*
> >> > > + * QTests for the SBTSI temperature sensor
> >> > > + *
> >> > > + * Copyright 2020 Google LLC
> >> > > + *
> >> > > + * This program is free software; you can redistribute it and/or
> >> modify it
> >> > > + * under the terms of the GNU General Public License as published by
> >> the
> >> > > + * Free Software Foundation; either version 2 of the License, or
> >> > > + * (at your option) any later version.
> >> > > + *
> >> > > + * This program is distributed in the hope that it will be useful,
> >> but
> >> > > WITHOUT
> >> > > + * ANY WARRANTY; without even the implied warranty of
> >> MERCHANTABILITY or
> >> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> >> License
> >> > > + * for more details.
> >> > > + */
> >> > > +
> >> > > +#include "qemu/osdep.h"
> >> > > +
> >> > > +#include "libqtest-single.h"
> >> > > +#include "libqos/qgraph.h"
> >> > > +#include "libqos/i2c.h"
> >> > > +#include "qapi/qmp/qdict.h"
> >> > > +#include "qemu/bitops.h"
> >> > > +
> >> > > +#define TEST_ID "sbtsi-test"
> >> > > +#define TEST_ADDR (0x4c)
> >> > > +
> >> > > +/*
> >> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
> >> registers
> >> > > are
> >> > > + * the integer part of a temperature value or limit, and "_DEC"
> >> registers
> >> > > are
> >> > > + * corresponding decimal parts.
> >> > > + */
> >> > > +#define REG_TEMP_INT 0x01 /* RO */
> >> > > +#define REG_STATUS 0x02 /* RO */
> >> > > +#define REG_CONFIG 0x03 /* RO */
> >> > > +#define REG_TEMP_HIGH_INT 0x07 /* RW */
> >> > > +#define REG_TEMP_LOW_INT 0x08 /* RW */
> >> > > +#define REG_CONFIG_WR 0x09 /* RW */
> >> > > +#define REG_TEMP_DEC 0x10 /* RO */
> >> > > +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
> >> > > +#define REG_TEMP_LOW_DEC 0x14 /* RW */
> >> > > +#define REG_ALERT_CONFIG 0xBF /* RW */
> >> > > +
> >> > > +#define STATUS_HIGH_ALERT BIT(4)
> >> > > +#define STATUS_LOW_ALERT BIT(3)
> >> > > +#define CONFIG_ALERT_MASK BIT(7)
> >> > > +#define ALARM_EN BIT(0)
> >> > > +
> >> > > +/* The temperature stored are in units of 0.125 degrees. */
> >> > > +#define TEMP_UNIT_IN_MILLIDEGREE 125
> >> > > +#define LIMIT_LOW (10500)
> >> > > +#define LIMIT_HIGH (55125)
> >> > > +
> >> > > +static uint32_t qmp_sbtsi_get_temperature(const char *id)
> >> > > +{
> >> > > + QDict *response;
> >> > > + int ret;
> >> > > +
> >> > > + response = qmp("{ 'execute': 'qom-get', 'arguments': { 'path':
> >> %s, "
> >> > > + "'property': 'temperature' } }", id);
> >> > > + g_assert(qdict_haskey(response, "return"));
> >> > > + ret = (uint32_t)qdict_get_int(response, "return");
> >> > > + qobject_unref(response);
> >> > > + return ret;
> >> > > +}
> >> > > +
> >> > > +static void qmp_sbtsi_set_temperature(const char *id, uint32_t value)
> >> > > +{
> >> > > + QDict *response;
> >> > > +
> >> > > + response = qmp("{ 'execute': 'qom-set', 'arguments': { 'path':
> >> %s, "
> >> > > + "'property': 'temperature', 'value': %d } }", id,
> >> > > value);
> >> > > + g_assert(qdict_haskey(response, "return"));
> >> > > + qobject_unref(response);
> >> > > +}
> >> > > +
> >> > > +/*
> >> > > + * Compute the temperature using the integer and decimal part and
> >> return
> >> > > + * millidegrees. The decimal part are only the top 3 bits so we
> >> shift it
> >> > > by
> >> > > + * 5 here.
> >> > > + */
> >> > > +static uint32_t regs_to_temp(uint8_t integer, uint8_t decimal)
> >> > > +{
> >> > > + return ((integer << 3) + (decimal >> 5)) *
> >> TEMP_UNIT_IN_MILLIDEGREE;
> >> > > +}
> >> > > +
> >> > > +/*
> >> > > + * Compute the integer and decimal parts of the temperature in
> >> > > millidegrees.
> >> > > + * H/W store the decimal in the top 3 bits so we shift it by 5.
> >> > > + */
> >> > > +static void temp_to_regs(uint32_t temp, uint8_t *integer, uint8_t
> >> > > *decimal)
> >> > > +{
> >> > > + temp /= TEMP_UNIT_IN_MILLIDEGREE;
> >> > > + *integer = temp >> 3;
> >> > > + *decimal = (temp & 0x7) << 5;
> >> > > +}
> >> > > +
> >> > > +static void tx_rx(void *obj, void *data, QGuestAllocator *alloc)
> >> > > +{
> >> > > + uint16_t value;
> >> > > + uint8_t integer, decimal;
> >> > > + QI2CDevice *i2cdev = (QI2CDevice *)obj;
> >> > > +
> >> > > + /* Test default values */
> >> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
> >> > > + g_assert_cmpuint(value, ==, 0);
> >> > > +
> >> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 0);
> >> > > +
> >> > > + /* Test setting temperature */
> >> > > + qmp_sbtsi_set_temperature(TEST_ID, 20000);
> >> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
> >> > > + g_assert_cmpuint(value, ==, 20000);
> >> > > +
> >> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 20000);
> >> > > +
> >> > > + /* Set alert mask in config */
> >> > > + i2c_set8(i2cdev, REG_CONFIG_WR, CONFIG_ALERT_MASK);
> >> > > + value = i2c_get8(i2cdev, REG_CONFIG);
> >> > > + g_assert_cmphex(value, ==, CONFIG_ALERT_MASK);
> >> > > + /* Enable alarm_en */
> >> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, ALARM_EN);
> >> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> >> > > + g_assert_cmphex(value, ==, ALARM_EN);
> >> > > +
> >> > > + /* Test setting limits */
> >> > > + /* Limit low = 10.500 */
> >> > > + temp_to_regs(LIMIT_LOW, &integer, &decimal);
> >> > > + i2c_set8(i2cdev, REG_TEMP_LOW_INT, integer);
> >> > > + i2c_set8(i2cdev, REG_TEMP_LOW_DEC, decimal);
> >> > > + integer = i2c_get8(i2cdev, REG_TEMP_LOW_INT);
> >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_LOW_DEC);
> >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_LOW);
> >> > > + /* Limit high = 55.125 */
> >> > > + temp_to_regs(LIMIT_HIGH, &integer, &decimal);
> >> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_INT, integer);
> >> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_DEC, decimal);
> >> > > + integer = i2c_get8(i2cdev, REG_TEMP_HIGH_INT);
> >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_HIGH_DEC);
> >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_HIGH);
> >> > > + /* No alert is generated. */
> >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> >> > > + g_assert_cmphex(value, ==, 0);
> >> > > +
> >> > > + /* Test alert for low temperature */
> >> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_LOW);
> >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> >> > > + g_assert_cmphex(value, ==, STATUS_LOW_ALERT);
> >> > > +
> >> > > + /* Test alert for high temperature */
> >> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_HIGH);
> >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> >> > > + g_assert_cmphex(value, ==, STATUS_HIGH_ALERT);
> >> > > +
> >> > > + /* Disable alarm_en */
> >> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, 0);
> >> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> >> > > + g_assert_cmphex(value, ==, 0);
> >> > > + /* No alert when alarm_en is false. */
> >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> >> > > + g_assert_cmphex(value, ==, 0);
> >> > > +}
> >> > > +
> >> > > +static void sbtsi_register_nodes(void)
> >> > > +{
> >> > > + QOSGraphEdgeOptions opts = {
> >> > > + .extra_device_opts = "id=" TEST_ID ",address=0x4c"
> >> > > + };
> >> > > + add_qi2c_address(&opts, &(QI2CAddress) { TEST_ADDR });
> >> > > +
> >> > > + qos_node_create_driver("sbtsi", i2c_device_create);
> >> > > + qos_node_consumes("sbtsi", "i2c-bus", &opts);
> >> > > +
> >> > > + qos_add_test("tx-rx", "sbtsi", tx_rx, NULL);
> >> > > +}
> >> > > +libqos_init(sbtsi_register_nodes);
> >> > > --
> >> >
> >> >
> >> > + Corey for i2c maintainer. The new sensor directory is mostly if not
> >> > entirely i2c devices. I didn't create a maintainer entry for this i2c
> >> > device, but I can if desired and send out a v2.
> >>
> >> Yeah, I guess I should be maintainer there. I'll queue up a change for
> >> that. Thanks.
> >>
> >> -corey
> >>
> >> >
> >> >
> >> > > 2.34.1.575.g55b058a8bb-goog
> >> > >
> >> > >
> >>
> >
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-27 14:55 ` Corey Minyard
@ 2022-01-27 18:19 ` Hao Wu
2022-01-27 23:18 ` Patrick Venture
0 siblings, 1 reply; 15+ messages in thread
From: Hao Wu @ 2022-01-27 18:19 UTC (permalink / raw)
To: Corey Minyard
Cc: Patrick Venture, Thomas Huth, Laurent Vivier, Paolo Bonzini,
QEMU Developers, Doug Evans
[-- Attachment #1: Type: text/plain, Size: 30943 bytes --]
On Thu, Jan 27, 2022 at 6:55 AM Corey Minyard <cminyard@mvista.com> wrote:
> On Wed, Jan 26, 2022 at 04:09:03PM -0800, Hao Wu wrote:
> > Hi,
> >
> > Sorry for the late reply. I'm not sure what "auto-increment" means here.
>
> The question is: When a value is read, does the address automatically
> increment. I2C devices very often do this. If you do a multi-byte
> read, they often will read the value from address 0, then from address
> 1, etc. Same for writes.
>
The datasheet does not suggest such behavior could happen.
>
> > The kernel driver at
> > https://lkml.org/lkml/2020/12/11/968
> > only has byte-size read/write operations, so I don't see a problem here.
> > The values are extracted
> > from the datasheet.
>
> The *Linux* kernel driver my only do byte-size operations, but other
> kernels may work different, and the Linux kernel may change. You have
> to implement from the datasheet, not the device driver.
>
The implementation is already according to the datasheet.
> Thanks,
>
> -corey
>
> >
> > On Tue, Jan 18, 2022 at 9:10 AM Patrick Venture <venture@google.com>
> wrote:
> >
> > >
> > >
> > > On Mon, Jan 17, 2022 at 6:05 AM Corey Minyard <cminyard@mvista.com>
> wrote:
> > >
> > >> On Sun, Jan 09, 2022 at 06:17:34PM -0800, Patrick Venture wrote:
> > >> > On Fri, Jan 7, 2022 at 7:04 PM Patrick Venture <venture@google.com>
> > >> wrote:
> > >> >
> > >> > > From: Hao Wu <wuhaotsh@google.com>
> > >> > >
> > >> > > SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
> > >> > > interface that reports AMD SoC's Ttcl (normalized temperature),
> > >> > > and resembles a typical 8-pin remote temperature sensor's I2C
> > >> interface
> > >> > > to BMC.
> > >> > >
> > >> > > This patch implements a basic AMD SB-TSI sensor that is
> > >> > > compatible with the open-source data sheet from AMD and Linux
> > >> > > kernel driver.
> > >> > >
> > >> > > Reference:
> > >> > > Linux kernel driver:
> > >> > > https://lkml.org/lkml/2020/12/11/968
> > >> > > Register Map:
> > >> > > https://developer.amd.com/wp-content/resources/56255_3_03.PDF
> > >> > > (Chapter 6)
> > >> > >
> > >> > > Signed-off-by: Hao Wu <wuhaotsh@google.com>
> > >> > > Reviewed-by: Doug Evans <dje@google.com>
> > >> > > ---
> > >> > > hw/sensor/Kconfig | 4 +
> > >> > > hw/sensor/meson.build | 1 +
> > >> > > hw/sensor/tmp_sbtsi.c | 393
> > >> +++++++++++++++++++++++++++++++++++
> > >> > > hw/sensor/trace-events | 5 +
> > >> > > hw/sensor/trace.h | 1 +
> > >> > > meson.build | 1 +
> > >> > > tests/qtest/meson.build | 1 +
> > >> > > tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
> > >> > > 8 files changed, 586 insertions(+)
> > >> > > create mode 100644 hw/sensor/tmp_sbtsi.c
> > >> > > create mode 100644 hw/sensor/trace-events
> > >> > > create mode 100644 hw/sensor/trace.h
> > >> > > create mode 100644 tests/qtest/tmp_sbtsi-test.c
> > >> > >
> > >> > > diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
> > >> > > index 9c8a049b06..27f6f79c84 100644
> > >> > > --- a/hw/sensor/Kconfig
> > >> > > +++ b/hw/sensor/Kconfig
> > >> > > @@ -21,3 +21,7 @@ config ADM1272
> > >> > > config MAX34451
> > >> > > bool
> > >> > > depends on I2C
> > >> > > +
> > >> > > +config AMDSBTSI
> > >> > > + bool
> > >> > > + depends on I2C
> > >> > > diff --git a/hw/sensor/meson.build b/hw/sensor/meson.build
> > >> > > index 059c4ca935..f7b0e645eb 100644
> > >> > > --- a/hw/sensor/meson.build
> > >> > > +++ b/hw/sensor/meson.build
> > >> > > @@ -4,3 +4,4 @@ softmmu_ss.add(when: 'CONFIG_DPS310', if_true:
> > >> > > files('dps310.c'))
> > >> > > softmmu_ss.add(when: 'CONFIG_EMC141X', if_true:
> files('emc141x.c'))
> > >> > > softmmu_ss.add(when: 'CONFIG_ADM1272', if_true:
> files('adm1272.c'))
> > >> > > softmmu_ss.add(when: 'CONFIG_MAX34451', if_true:
> files('max34451.c'))
> > >> > > +softmmu_ss.add(when: 'CONFIG_AMDSBTSI', if_true:
> > >> files('tmp_sbtsi.c'))
> > >> > > diff --git a/hw/sensor/tmp_sbtsi.c b/hw/sensor/tmp_sbtsi.c
> > >> > > new file mode 100644
> > >> > > index 0000000000..b68c7ebf61
> > >> > > --- /dev/null
> > >> > > +++ b/hw/sensor/tmp_sbtsi.c
> > >> > > @@ -0,0 +1,393 @@
> > >> > > +/*
> > >> > > + * AMD SBI Temperature Sensor Interface (SB-TSI)
> > >> > > + *
> > >> > > + * Copyright 2021 Google LLC
> > >> > > + *
> > >> > > + * This program is free software; you can redistribute it and/or
> > >> modify it
> > >> > > + * under the terms of the GNU General Public License as
> published by
> > >> the
> > >> > > + * Free Software Foundation; either version 2 of the License, or
> > >> > > + * (at your option) any later version.
> > >> > > + *
> > >> > > + * This program is distributed in the hope that it will be
> useful,
> > >> but
> > >> > > WITHOUT
> > >> > > + * ANY WARRANTY; without even the implied warranty of
> > >> MERCHANTABILITY or
> > >> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> > >> License
> > >> > > + * for more details.
> > >> > > + */
> > >> > > +
> > >> > > +#include "qemu/osdep.h"
> > >> > > +#include "hw/i2c/smbus_slave.h"
> > >> > > +#include "hw/irq.h"
> > >> > > +#include "migration/vmstate.h"
> > >> > > +#include "qapi/error.h"
> > >> > > +#include "qapi/visitor.h"
> > >> > > +#include "qemu/log.h"
> > >> > > +#include "qemu/module.h"
> > >> > > +#include "trace.h"
> > >> > > +
> > >> > > +#define TYPE_SBTSI "sbtsi"
> > >> > > +#define SBTSI(obj) OBJECT_CHECK(SBTSIState, (obj), TYPE_SBTSI)
> > >> > > +
> > >> > > +/**
> > >> > > + * SBTSIState:
> > >> > > + * temperatures are in units of 0.125 degrees
> > >> > > + * @temperature: Temperature
> > >> > > + * @limit_low: Lowest temperature
> > >> > > + * @limit_high: Highest temperature
> > >> > > + * @status: The status register
> > >> > > + * @config: The config register
> > >> > > + * @alert_config: The config for alarm_l output.
> > >> > > + * @addr: The address to read/write for the next cmd.
> > >> > > + * @alarm: The alarm_l output pin (GPIO)
> > >> > > + */
> > >> > > +typedef struct SBTSIState {
> > >> > > + SMBusDevice parent;
> > >> > > +
> > >> > > + uint32_t temperature;
> > >> > > + uint32_t limit_low;
> > >> > > + uint32_t limit_high;
> > >> > > + uint8_t status;
> > >> > > + uint8_t config;
> > >> > > + uint8_t alert_config;
> > >> > > + uint8_t addr;
> > >> > > + qemu_irq alarm;
> > >> > > +} SBTSIState;
> > >> > > +
> > >> > > +/*
> > >> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
> > >> registers
> > >> > > are
> > >> > > + * the integer part of a temperature value or limit, and "_DEC"
> > >> registers
> > >> > > are
> > >> > > + * corresponding decimal parts.
> > >> > > + */
> > >> > > +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
> > >> > > +#define SBTSI_REG_STATUS 0x02 /* RO */
> > >> > > +#define SBTSI_REG_CONFIG 0x03 /* RO */
> > >> > > +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
> > >> > > +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
> > >> > > +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
> > >> > > +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
> > >> > > +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
> > >> > > +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
> > >> > > +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
> > >> > > +#define SBTSI_REG_MAN 0xFE /* RO */
> > >> > > +#define SBTSI_REG_REV 0xFF /* RO */
> > >> > > +
> > >> > > +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
> > >> > > +#define SBTSI_STATUS_LOW_ALERT BIT(3)
> > >> > > +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
> > >> > > +#define SBTSI_ALARM_EN BIT(0)
> > >> > > +
> > >> > > +#define SBTSI_LIMIT_LOW_DEFAULT (0)
> > >> > > +#define SBTSI_LIMIT_HIGH_DEFAULT (560)
> > >> > > +#define SBTSI_MAN_DEFAULT (0)
> > >> > > +#define SBTSI_REV_DEFAULT (4)
> > >> > > +#define SBTSI_ALARM_L "alarm_l"
> > >> > > +
> > >> > > +/* The temperature we stored are in units of 0.125 degrees. */
> > >> > > +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
> > >> > > +
> > >> > > +/*
> > >> > > + * The integer part and decimal of the temperature both 8 bits.
> > >> > > + * Only the top 3 bits of the decimal parts are used.
> > >> > > + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875
> degrees.
> > >> > > + */
> > >> > > +#define SBTSI_TEMP_MAX 255875
> > >> > > +
> > >> > > +/* The integer part of the temperature in terms of 0.125
> degrees. */
> > >> > > +static uint8_t get_temp_int(uint32_t temp)
> > >> > > +{
> > >> > > + return temp >> 3;
> > >> > > +}
> > >> > > +
> > >> > > +/*
> > >> > > + * The decimal part of the temperature, in terms of 0.125
> degrees.
> > >> > > + * H/W store it in the top 3 bits so we shift it by 5.
> > >> > > + */
> > >> > > +static uint8_t get_temp_dec(uint32_t temp)
> > >> > > +{
> > >> > > + return (temp & 0x7) << 5;
> > >> > > +}
> > >> > > +
> > >> > > +/*
> > >> > > + * Compute the temperature using the integer and decimal part,
> > >> > > + * in terms of 0.125 degrees. The decimal part are only the top 3
> > >> bits
> > >> > > + * so we shift it by 5 here.
> > >> > > + */
> > >> > > +static uint32_t compute_temp(uint8_t integer, uint8_t decimal)
> > >> > > +{
> > >> > > + return (integer << 3) + (decimal >> 5);
> > >> > > +}
> > >> > > +
> > >> > > +/* Compute new temp with new int part of the temperature. */
> > >> > > +static uint32_t compute_temp_int(uint32_t temp, uint8_t integer)
> > >> > > +{
> > >> > > + return compute_temp(integer, get_temp_dec(temp));
> > >> > > +}
> > >> > > +
> > >> > > +/* Compute new temp with new dec part of the temperature. */
> > >> > > +static uint32_t compute_temp_dec(uint32_t temp, uint8_t decimal)
> > >> > > +{
> > >> > > + return compute_temp(get_temp_int(temp), decimal);
> > >> > > +}
> > >> > > +
> > >> > > +/* The integer part of the temperature. */
> > >> > > +static void sbtsi_update_status(SBTSIState *s)
> > >> > > +{
> > >> > > + s->status = 0;
> > >> > > + if (s->alert_config & SBTSI_ALARM_EN) {
> > >> > > + if (s->temperature >= s->limit_high) {
> > >> > > + s->status |= SBTSI_STATUS_HIGH_ALERT;
> > >> > > + }
> > >> > > + if (s->temperature <= s->limit_low) {
> > >> > > + s->status |= SBTSI_STATUS_LOW_ALERT;
> > >> > > + }
> > >> > > + }
> > >> > > +}
> > >> > > +
> > >> > > +static void sbtsi_update_alarm(SBTSIState *s)
> > >> > > +{
> > >> > > + sbtsi_update_status(s);
> > >> > > + if (s->status != 0 && !(s->config &
> SBTSI_CONFIG_ALERT_MASK)) {
> > >> > > + qemu_irq_raise(s->alarm);
> > >> > > + } else {
> > >> > > + qemu_irq_lower(s->alarm);
> > >> > > + }
> > >> > > +}
> > >> > > +
> > >> > > +static uint8_t sbtsi_read_byte(SMBusDevice *d)
> > >> > > +{
> > >> > > + SBTSIState *s = SBTSI(d);
> > >> > > + uint8_t data = 0;
> > >> > > +
> > >> > > + switch (s->addr) {
> > >> > > + case SBTSI_REG_TEMP_INT:
> > >> > > + data = get_temp_int(s->temperature);
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_TEMP_DEC:
> > >> > > + data = get_temp_dec(s->temperature);
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_TEMP_HIGH_INT:
> > >> > > + data = get_temp_int(s->limit_high);
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_TEMP_LOW_INT:
> > >> > > + data = get_temp_int(s->limit_low);
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_TEMP_HIGH_DEC:
> > >> > > + data = get_temp_dec(s->limit_high);
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_TEMP_LOW_DEC:
> > >> > > + data = get_temp_dec(s->limit_low);
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_CONFIG:
> > >> > > + case SBTSI_REG_CONFIG_WR:
> > >> > > + data = s->config;
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_STATUS:
> > >> > > + sbtsi_update_alarm(s);
> > >> > > + data = s->status;
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_ALERT_CONFIG:
> > >> > > + data = s->alert_config;
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_MAN:
> > >> > > + data = SBTSI_MAN_DEFAULT;
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_REV:
> > >> > > + data = SBTSI_REV_DEFAULT;
> > >> > > + break;
> > >>
> > >> Does this device do some sort of auto-increment on the address when
> > >> reading/writing?
> > >>
> > >
> > > +Hao Wu <wuhaotsh@google.com> - Please take a look at the above
> > > question. I imagine it's a while since you've thought about it, but
> please
> > > double check :)
> > > Thanks!
> > >
> > >
> > >> Other than that possible issue, I don't see anything else, it's pretty
> > >> straightforward.
> > >>
> > >> > > +
> > >> > > + default:
> > >> > > + qemu_log_mask(LOG_GUEST_ERROR,
> > >> > > + "%s: reading from invalid reg: 0x%02x\n",
> > >> > > + __func__, s->addr);
> > >> > > + break;
> > >> > > + }
> > >> > > +
> > >> > > + trace_tmp_sbtsi_read_data(s->addr, data);
> > >> > > + return data;
> > >> > > +}
> > >> > > +
> > >> > > +static void sbtsi_write(SBTSIState *s, uint8_t data)
> > >> > > +{
> > >> > > + trace_tmp_sbtsi_write_data(s->addr, data);
> > >> > > + switch (s->addr) {
> > >> > > + case SBTSI_REG_CONFIG_WR:
> > >> > > + s->config = data;
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_TEMP_HIGH_INT:
> > >> > > + s->limit_high = compute_temp_int(s->limit_high, data);
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_TEMP_LOW_INT:
> > >> > > + s->limit_low = compute_temp_int(s->limit_low, data);
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_TEMP_HIGH_DEC:
> > >> > > + s->limit_high = compute_temp_dec(s->limit_high, data);
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_TEMP_LOW_DEC:
> > >> > > + s->limit_low = compute_temp_dec(s->limit_low, data);
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_ALERT_CONFIG:
> > >> > > + s->alert_config = data;
> > >> > > + break;
> > >> > > +
> > >> > > + case SBTSI_REG_TEMP_INT:
> > >> > > + case SBTSI_REG_TEMP_DEC:
> > >> > > + case SBTSI_REG_CONFIG:
> > >> > > + case SBTSI_REG_STATUS:
> > >> > > + case SBTSI_REG_MAN:
> > >> > > + case SBTSI_REG_REV:
> > >> > > + qemu_log_mask(LOG_GUEST_ERROR,
> > >> > > + "%s: writing to read only reg: 0x%02x data:
> > >> 0x%02x\n",
> > >> > > + __func__, s->addr, data);
> > >> > > + break;
> > >> > > +
> > >> > > + default:
> > >> > > + qemu_log_mask(LOG_GUEST_ERROR,
> > >> > > + "%s: writing to invalid reg: 0x%02x data:
> 0x%02x\n",
> > >> > > + __func__, s->addr, data);
> > >> > > + break;
> > >> > > + }
> > >> > > + sbtsi_update_alarm(s);
> > >> > > +}
> > >> > > +
> > >> > > +static int sbtsi_write_data(SMBusDevice *d, uint8_t *buf, uint8_t
> > >> len)
> > >> > > +{
> > >> > > + SBTSIState *s = SBTSI(d);
> > >> > > +
> > >> > > + if (len == 0) {
> > >> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: writing empty
> data\n",
> > >> > > __func__);
> > >> > > + return -1;
> > >> > > + }
> > >> > > +
> > >> > > + s->addr = buf[0];
> > >> > > + if (len > 1) {
> > >> > > + sbtsi_write(s, buf[1]);
> > >> > > + if (len > 2) {
> > >> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: extra data at
> end\n",
> > >> > > __func__);
> > >> > > + }
> > >> > > + }
> > >> > > + return 0;
> > >> > > +}
> > >> > > +
> > >> > > +/* Units are millidegrees. */
> > >> > > +static void sbtsi_get_temperature(Object *obj, Visitor *v, const
> char
> > >> > > *name,
> > >> > > + void *opaque, Error **errp)
> > >> > > +{
> > >> > > + SBTSIState *s = SBTSI(obj);
> > >> > > + uint32_t temp = s->temperature *
> SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> > >> > > +
> > >> > > + visit_type_uint32(v, name, &temp, errp);
> > >> > > +}
> > >> > > +
> > >> > > +/* Units are millidegrees. */
> > >> > > +static void sbtsi_set_temperature(Object *obj, Visitor *v, const
> char
> > >> > > *name,
> > >> > > + void *opaque, Error **errp)
> > >> > > +{
> > >> > > + SBTSIState *s = SBTSI(obj);
> > >> > > + uint32_t temp;
> > >> > > +
> > >> > > + if (!visit_type_uint32(v, name, &temp, errp)) {
> > >> > > + return;
> > >> > > + }
> > >> > > + if (temp > SBTSI_TEMP_MAX) {
> > >> > > + error_setg(errp, "value %" PRIu32 ".%03" PRIu32 " C is
> out of
> > >> > > range",
> > >> > > + temp / 1000, temp % 1000);
> > >> > > + return;
> > >> > > + }
> > >> > > +
> > >> > > + s->temperature = temp / SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> > >> > > + sbtsi_update_alarm(s);
> > >> > > +}
> > >> > > +
> > >> > > +static int sbtsi_post_load(void *opaque, int version_id)
> > >> > > +{
> > >> > > + SBTSIState *s = opaque;
> > >> > > +
> > >> > > + sbtsi_update_alarm(s);
> > >> > > + return 0;
> > >> > > +}
> > >> > > +
> > >> > > +static const VMStateDescription vmstate_sbtsi = {
> > >> > > + .name = "SBTSI",
> > >> > > + .version_id = 0,
> > >> > > + .minimum_version_id = 0,
> > >> > > + .post_load = sbtsi_post_load,
> > >> > > + .fields = (VMStateField[]) {
> > >> > > + VMSTATE_UINT32(temperature, SBTSIState),
> > >> > > + VMSTATE_UINT32(limit_low, SBTSIState),
> > >> > > + VMSTATE_UINT32(limit_high, SBTSIState),
> > >> > > + VMSTATE_UINT8(config, SBTSIState),
> > >> > > + VMSTATE_UINT8(status, SBTSIState),
> > >> > > + VMSTATE_UINT8(addr, SBTSIState),
> > >> > > + VMSTATE_END_OF_LIST()
> > >> > > + }
> > >> > > +};
> > >> > > +
> > >> > > +static void sbtsi_enter_reset(Object *obj, ResetType type)
> > >> > > +{
> > >> > > + SBTSIState *s = SBTSI(obj);
> > >> > > +
> > >> > > + s->config = 0;
> > >> > > + s->limit_low = SBTSI_LIMIT_LOW_DEFAULT;
> > >> > > + s->limit_high = SBTSI_LIMIT_HIGH_DEFAULT;
> > >> > > +}
> > >> > > +
> > >> > > +static void sbtsi_hold_reset(Object *obj)
> > >> > > +{
> > >> > > + SBTSIState *s = SBTSI(obj);
> > >> > > +
> > >> > > + qemu_irq_lower(s->alarm);
> > >> > > +}
> > >> > > +
> > >> > > +static void sbtsi_init(Object *obj)
> > >> > > +{
> > >> > > + SBTSIState *s = SBTSI(obj);
> > >> > > +
> > >> > > + /* Current temperature in millidegrees. */
> > >> > > + object_property_add(obj, "temperature", "uint32",
> > >> > > + sbtsi_get_temperature,
> sbtsi_set_temperature,
> > >> > > + NULL, NULL);
> > >> > > + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm,
> SBTSI_ALARM_L,
> > >> 0);
> > >> > > +}
> > >> > > +
> > >> > > +static void sbtsi_class_init(ObjectClass *klass, void *data)
> > >> > > +{
> > >> > > + ResettableClass *rc = RESETTABLE_CLASS(klass);
> > >> > > + DeviceClass *dc = DEVICE_CLASS(klass);
> > >> > > + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
> > >> > > +
> > >> > > + dc->desc = "SB-TSI Temperature Sensor";
> > >> > > + dc->vmsd = &vmstate_sbtsi;
> > >> > > + k->write_data = sbtsi_write_data;
> > >> > > + k->receive_byte = sbtsi_read_byte;
> > >> > > + rc->phases.enter = sbtsi_enter_reset;
> > >> > > + rc->phases.hold = sbtsi_hold_reset;
> > >> > > +}
> > >> > > +
> > >> > > +static const TypeInfo sbtsi_info = {
> > >> > > + .name = TYPE_SBTSI,
> > >> > > + .parent = TYPE_SMBUS_DEVICE,
> > >> > > + .instance_size = sizeof(SBTSIState),
> > >> > > + .instance_init = sbtsi_init,
> > >> > > + .class_init = sbtsi_class_init,
> > >> > > +};
> > >> > > +
> > >> > > +static void sbtsi_register_types(void)
> > >> > > +{
> > >> > > + type_register_static(&sbtsi_info);
> > >> > > +}
> > >> > > +
> > >> > > +type_init(sbtsi_register_types)
> > >> > > diff --git a/hw/sensor/trace-events b/hw/sensor/trace-events
> > >> > > new file mode 100644
> > >> > > index 0000000000..21ab3809e2
> > >> > > --- /dev/null
> > >> > > +++ b/hw/sensor/trace-events
> > >> > > @@ -0,0 +1,5 @@
> > >> > > +# See docs/devel/tracing.rst for syntax documentation.
> > >> > > +
> > >> > > +# tmp_sbtsi.c
> > >> > > +tmp_sbtsi_write_data(uint8_t addr, uint8_t value) "SBTSI write
> > >> > > addr:0x%02x data: 0x%02x"
> > >> > > +tmp_sbtsi_read_data(uint8_t addr, uint8_t value) "SBTSI read
> > >> addr:0x%02x
> > >> > > data: 0x%02x"
> > >> > > diff --git a/hw/sensor/trace.h b/hw/sensor/trace.h
> > >> > > new file mode 100644
> > >> > > index 0000000000..e4721560b0
> > >> > > --- /dev/null
> > >> > > +++ b/hw/sensor/trace.h
> > >> > > @@ -0,0 +1 @@
> > >> > > +#include "trace/trace-hw_sensor.h"
> > >> > > diff --git a/meson.build b/meson.build
> > >> > > index 53065e96ec..f8ab0bf74e 100644
> > >> > > --- a/meson.build
> > >> > > +++ b/meson.build
> > >> > > @@ -2494,6 +2494,7 @@ if have_system
> > >> > > 'hw/rtc',
> > >> > > 'hw/s390x',
> > >> > > 'hw/scsi',
> > >> > > + 'hw/sensor',
> > >> > > 'hw/sd',
> > >> > > 'hw/sh4',
> > >> > > 'hw/sparc',
> > >> > > diff --git a/tests/qtest/meson.build b/tests/qtest/meson.build
> > >> > > index 37e1eaa449..d1a8c38f74 100644
> > >> > > --- a/tests/qtest/meson.build
> > >> > > +++ b/tests/qtest/meson.build
> > >> > > @@ -254,6 +254,7 @@ qos_test_ss.add(
> > >> > > 'spapr-phb-test.c',
> > >> > > 'tmp105-test.c',
> > >> > > 'emc141x-test.c',
> > >> > > + 'tmp_sbtsi-test.c',
> > >> > > 'usb-hcd-ohci-test.c',
> > >> > > 'virtio-test.c',
> > >> > > 'virtio-blk-test.c',
> > >> > > diff --git a/tests/qtest/tmp_sbtsi-test.c
> > >> b/tests/qtest/tmp_sbtsi-test.c
> > >> > > new file mode 100644
> > >> > > index 0000000000..7f5fafacc7
> > >> > > --- /dev/null
> > >> > > +++ b/tests/qtest/tmp_sbtsi-test.c
> > >> > > @@ -0,0 +1,180 @@
> > >> > > +/*
> > >> > > + * QTests for the SBTSI temperature sensor
> > >> > > + *
> > >> > > + * Copyright 2020 Google LLC
> > >> > > + *
> > >> > > + * This program is free software; you can redistribute it and/or
> > >> modify it
> > >> > > + * under the terms of the GNU General Public License as
> published by
> > >> the
> > >> > > + * Free Software Foundation; either version 2 of the License, or
> > >> > > + * (at your option) any later version.
> > >> > > + *
> > >> > > + * This program is distributed in the hope that it will be
> useful,
> > >> but
> > >> > > WITHOUT
> > >> > > + * ANY WARRANTY; without even the implied warranty of
> > >> MERCHANTABILITY or
> > >> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> > >> License
> > >> > > + * for more details.
> > >> > > + */
> > >> > > +
> > >> > > +#include "qemu/osdep.h"
> > >> > > +
> > >> > > +#include "libqtest-single.h"
> > >> > > +#include "libqos/qgraph.h"
> > >> > > +#include "libqos/i2c.h"
> > >> > > +#include "qapi/qmp/qdict.h"
> > >> > > +#include "qemu/bitops.h"
> > >> > > +
> > >> > > +#define TEST_ID "sbtsi-test"
> > >> > > +#define TEST_ADDR (0x4c)
> > >> > > +
> > >> > > +/*
> > >> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
> > >> registers
> > >> > > are
> > >> > > + * the integer part of a temperature value or limit, and "_DEC"
> > >> registers
> > >> > > are
> > >> > > + * corresponding decimal parts.
> > >> > > + */
> > >> > > +#define REG_TEMP_INT 0x01 /* RO */
> > >> > > +#define REG_STATUS 0x02 /* RO */
> > >> > > +#define REG_CONFIG 0x03 /* RO */
> > >> > > +#define REG_TEMP_HIGH_INT 0x07 /* RW */
> > >> > > +#define REG_TEMP_LOW_INT 0x08 /* RW */
> > >> > > +#define REG_CONFIG_WR 0x09 /* RW */
> > >> > > +#define REG_TEMP_DEC 0x10 /* RO */
> > >> > > +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
> > >> > > +#define REG_TEMP_LOW_DEC 0x14 /* RW */
> > >> > > +#define REG_ALERT_CONFIG 0xBF /* RW */
> > >> > > +
> > >> > > +#define STATUS_HIGH_ALERT BIT(4)
> > >> > > +#define STATUS_LOW_ALERT BIT(3)
> > >> > > +#define CONFIG_ALERT_MASK BIT(7)
> > >> > > +#define ALARM_EN BIT(0)
> > >> > > +
> > >> > > +/* The temperature stored are in units of 0.125 degrees. */
> > >> > > +#define TEMP_UNIT_IN_MILLIDEGREE 125
> > >> > > +#define LIMIT_LOW (10500)
> > >> > > +#define LIMIT_HIGH (55125)
> > >> > > +
> > >> > > +static uint32_t qmp_sbtsi_get_temperature(const char *id)
> > >> > > +{
> > >> > > + QDict *response;
> > >> > > + int ret;
> > >> > > +
> > >> > > + response = qmp("{ 'execute': 'qom-get', 'arguments': {
> 'path':
> > >> %s, "
> > >> > > + "'property': 'temperature' } }", id);
> > >> > > + g_assert(qdict_haskey(response, "return"));
> > >> > > + ret = (uint32_t)qdict_get_int(response, "return");
> > >> > > + qobject_unref(response);
> > >> > > + return ret;
> > >> > > +}
> > >> > > +
> > >> > > +static void qmp_sbtsi_set_temperature(const char *id, uint32_t
> value)
> > >> > > +{
> > >> > > + QDict *response;
> > >> > > +
> > >> > > + response = qmp("{ 'execute': 'qom-set', 'arguments': {
> 'path':
> > >> %s, "
> > >> > > + "'property': 'temperature', 'value': %d } }",
> id,
> > >> > > value);
> > >> > > + g_assert(qdict_haskey(response, "return"));
> > >> > > + qobject_unref(response);
> > >> > > +}
> > >> > > +
> > >> > > +/*
> > >> > > + * Compute the temperature using the integer and decimal part and
> > >> return
> > >> > > + * millidegrees. The decimal part are only the top 3 bits so we
> > >> shift it
> > >> > > by
> > >> > > + * 5 here.
> > >> > > + */
> > >> > > +static uint32_t regs_to_temp(uint8_t integer, uint8_t decimal)
> > >> > > +{
> > >> > > + return ((integer << 3) + (decimal >> 5)) *
> > >> TEMP_UNIT_IN_MILLIDEGREE;
> > >> > > +}
> > >> > > +
> > >> > > +/*
> > >> > > + * Compute the integer and decimal parts of the temperature in
> > >> > > millidegrees.
> > >> > > + * H/W store the decimal in the top 3 bits so we shift it by 5.
> > >> > > + */
> > >> > > +static void temp_to_regs(uint32_t temp, uint8_t *integer, uint8_t
> > >> > > *decimal)
> > >> > > +{
> > >> > > + temp /= TEMP_UNIT_IN_MILLIDEGREE;
> > >> > > + *integer = temp >> 3;
> > >> > > + *decimal = (temp & 0x7) << 5;
> > >> > > +}
> > >> > > +
> > >> > > +static void tx_rx(void *obj, void *data, QGuestAllocator *alloc)
> > >> > > +{
> > >> > > + uint16_t value;
> > >> > > + uint8_t integer, decimal;
> > >> > > + QI2CDevice *i2cdev = (QI2CDevice *)obj;
> > >> > > +
> > >> > > + /* Test default values */
> > >> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
> > >> > > + g_assert_cmpuint(value, ==, 0);
> > >> > > +
> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 0);
> > >> > > +
> > >> > > + /* Test setting temperature */
> > >> > > + qmp_sbtsi_set_temperature(TEST_ID, 20000);
> > >> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
> > >> > > + g_assert_cmpuint(value, ==, 20000);
> > >> > > +
> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 20000);
> > >> > > +
> > >> > > + /* Set alert mask in config */
> > >> > > + i2c_set8(i2cdev, REG_CONFIG_WR, CONFIG_ALERT_MASK);
> > >> > > + value = i2c_get8(i2cdev, REG_CONFIG);
> > >> > > + g_assert_cmphex(value, ==, CONFIG_ALERT_MASK);
> > >> > > + /* Enable alarm_en */
> > >> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, ALARM_EN);
> > >> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> > >> > > + g_assert_cmphex(value, ==, ALARM_EN);
> > >> > > +
> > >> > > + /* Test setting limits */
> > >> > > + /* Limit low = 10.500 */
> > >> > > + temp_to_regs(LIMIT_LOW, &integer, &decimal);
> > >> > > + i2c_set8(i2cdev, REG_TEMP_LOW_INT, integer);
> > >> > > + i2c_set8(i2cdev, REG_TEMP_LOW_DEC, decimal);
> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_LOW_INT);
> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_LOW_DEC);
> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==,
> LIMIT_LOW);
> > >> > > + /* Limit high = 55.125 */
> > >> > > + temp_to_regs(LIMIT_HIGH, &integer, &decimal);
> > >> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_INT, integer);
> > >> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_DEC, decimal);
> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_HIGH_INT);
> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_HIGH_DEC);
> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==,
> LIMIT_HIGH);
> > >> > > + /* No alert is generated. */
> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> > >> > > + g_assert_cmphex(value, ==, 0);
> > >> > > +
> > >> > > + /* Test alert for low temperature */
> > >> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_LOW);
> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> > >> > > + g_assert_cmphex(value, ==, STATUS_LOW_ALERT);
> > >> > > +
> > >> > > + /* Test alert for high temperature */
> > >> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_HIGH);
> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> > >> > > + g_assert_cmphex(value, ==, STATUS_HIGH_ALERT);
> > >> > > +
> > >> > > + /* Disable alarm_en */
> > >> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, 0);
> > >> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> > >> > > + g_assert_cmphex(value, ==, 0);
> > >> > > + /* No alert when alarm_en is false. */
> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> > >> > > + g_assert_cmphex(value, ==, 0);
> > >> > > +}
> > >> > > +
> > >> > > +static void sbtsi_register_nodes(void)
> > >> > > +{
> > >> > > + QOSGraphEdgeOptions opts = {
> > >> > > + .extra_device_opts = "id=" TEST_ID ",address=0x4c"
> > >> > > + };
> > >> > > + add_qi2c_address(&opts, &(QI2CAddress) { TEST_ADDR });
> > >> > > +
> > >> > > + qos_node_create_driver("sbtsi", i2c_device_create);
> > >> > > + qos_node_consumes("sbtsi", "i2c-bus", &opts);
> > >> > > +
> > >> > > + qos_add_test("tx-rx", "sbtsi", tx_rx, NULL);
> > >> > > +}
> > >> > > +libqos_init(sbtsi_register_nodes);
> > >> > > --
> > >> >
> > >> >
> > >> > + Corey for i2c maintainer. The new sensor directory is mostly if
> not
> > >> > entirely i2c devices. I didn't create a maintainer entry for this
> i2c
> > >> > device, but I can if desired and send out a v2.
> > >>
> > >> Yeah, I guess I should be maintainer there. I'll queue up a change
> for
> > >> that. Thanks.
> > >>
> > >> -corey
> > >>
> > >> >
> > >> >
> > >> > > 2.34.1.575.g55b058a8bb-goog
> > >> > >
> > >> > >
> > >>
> > >
>
[-- Attachment #2: Type: text/html, Size: 47877 bytes --]
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-27 18:19 ` Hao Wu
@ 2022-01-27 23:18 ` Patrick Venture
2022-01-28 1:58 ` Corey Minyard
0 siblings, 1 reply; 15+ messages in thread
From: Patrick Venture @ 2022-01-27 23:18 UTC (permalink / raw)
To: Hao Wu
Cc: Corey Minyard, Thomas Huth, Laurent Vivier, Paolo Bonzini,
QEMU Developers, Doug Evans
[-- Attachment #1: Type: text/plain, Size: 32163 bytes --]
On Thu, Jan 27, 2022 at 10:20 AM Hao Wu <wuhaotsh@google.com> wrote:
>
> On Thu, Jan 27, 2022 at 6:55 AM Corey Minyard <cminyard@mvista.com> wrote:
>
>> On Wed, Jan 26, 2022 at 04:09:03PM -0800, Hao Wu wrote:
>> > Hi,
>> >
>> > Sorry for the late reply. I'm not sure what "auto-increment" means here.
>>
>> The question is: When a value is read, does the address automatically
>> increment. I2C devices very often do this. If you do a multi-byte
>> read, they often will read the value from address 0, then from address
>> 1, etc. Same for writes.
>>
> The datasheet does not suggest such behavior could happen.
>
>>
>> > The kernel driver at
>> > https://lkml.org/lkml/2020/12/11/968
>> > only has byte-size read/write operations, so I don't see a problem here.
>> > The values are extracted
>> > from the datasheet.
>>
>> The *Linux* kernel driver my only do byte-size operations, but other
>> kernels may work different, and the Linux kernel may change. You have
>> to implement from the datasheet, not the device driver.
>>
> The implementation is already according to the datasheet.
>
>> Thanks,
>>
>> -corey
>>
>>
I have to send out a new patchset to include my signature block since I'm
sending a patch Hao wrote. Laurent pointed this out to me in a different
patch series.
From this exchange, I don't think there are other changes for v2. Please
let me know if that's false.
Thanks,
Patrick
> >
>> > On Tue, Jan 18, 2022 at 9:10 AM Patrick Venture <venture@google.com>
>> wrote:
>> >
>> > >
>> > >
>> > > On Mon, Jan 17, 2022 at 6:05 AM Corey Minyard <cminyard@mvista.com>
>> wrote:
>> > >
>> > >> On Sun, Jan 09, 2022 at 06:17:34PM -0800, Patrick Venture wrote:
>> > >> > On Fri, Jan 7, 2022 at 7:04 PM Patrick Venture <venture@google.com
>> >
>> > >> wrote:
>> > >> >
>> > >> > > From: Hao Wu <wuhaotsh@google.com>
>> > >> > >
>> > >> > > SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
>> > >> > > interface that reports AMD SoC's Ttcl (normalized temperature),
>> > >> > > and resembles a typical 8-pin remote temperature sensor's I2C
>> > >> interface
>> > >> > > to BMC.
>> > >> > >
>> > >> > > This patch implements a basic AMD SB-TSI sensor that is
>> > >> > > compatible with the open-source data sheet from AMD and Linux
>> > >> > > kernel driver.
>> > >> > >
>> > >> > > Reference:
>> > >> > > Linux kernel driver:
>> > >> > > https://lkml.org/lkml/2020/12/11/968
>> > >> > > Register Map:
>> > >> > > https://developer.amd.com/wp-content/resources/56255_3_03.PDF
>> > >> > > (Chapter 6)
>> > >> > >
>> > >> > > Signed-off-by: Hao Wu <wuhaotsh@google.com>
>> > >> > > Reviewed-by: Doug Evans <dje@google.com>
>> > >> > > ---
>> > >> > > hw/sensor/Kconfig | 4 +
>> > >> > > hw/sensor/meson.build | 1 +
>> > >> > > hw/sensor/tmp_sbtsi.c | 393
>> > >> +++++++++++++++++++++++++++++++++++
>> > >> > > hw/sensor/trace-events | 5 +
>> > >> > > hw/sensor/trace.h | 1 +
>> > >> > > meson.build | 1 +
>> > >> > > tests/qtest/meson.build | 1 +
>> > >> > > tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
>> > >> > > 8 files changed, 586 insertions(+)
>> > >> > > create mode 100644 hw/sensor/tmp_sbtsi.c
>> > >> > > create mode 100644 hw/sensor/trace-events
>> > >> > > create mode 100644 hw/sensor/trace.h
>> > >> > > create mode 100644 tests/qtest/tmp_sbtsi-test.c
>> > >> > >
>> > >> > > diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
>> > >> > > index 9c8a049b06..27f6f79c84 100644
>> > >> > > --- a/hw/sensor/Kconfig
>> > >> > > +++ b/hw/sensor/Kconfig
>> > >> > > @@ -21,3 +21,7 @@ config ADM1272
>> > >> > > config MAX34451
>> > >> > > bool
>> > >> > > depends on I2C
>> > >> > > +
>> > >> > > +config AMDSBTSI
>> > >> > > + bool
>> > >> > > + depends on I2C
>> > >> > > diff --git a/hw/sensor/meson.build b/hw/sensor/meson.build
>> > >> > > index 059c4ca935..f7b0e645eb 100644
>> > >> > > --- a/hw/sensor/meson.build
>> > >> > > +++ b/hw/sensor/meson.build
>> > >> > > @@ -4,3 +4,4 @@ softmmu_ss.add(when: 'CONFIG_DPS310', if_true:
>> > >> > > files('dps310.c'))
>> > >> > > softmmu_ss.add(when: 'CONFIG_EMC141X', if_true:
>> files('emc141x.c'))
>> > >> > > softmmu_ss.add(when: 'CONFIG_ADM1272', if_true:
>> files('adm1272.c'))
>> > >> > > softmmu_ss.add(when: 'CONFIG_MAX34451', if_true:
>> files('max34451.c'))
>> > >> > > +softmmu_ss.add(when: 'CONFIG_AMDSBTSI', if_true:
>> > >> files('tmp_sbtsi.c'))
>> > >> > > diff --git a/hw/sensor/tmp_sbtsi.c b/hw/sensor/tmp_sbtsi.c
>> > >> > > new file mode 100644
>> > >> > > index 0000000000..b68c7ebf61
>> > >> > > --- /dev/null
>> > >> > > +++ b/hw/sensor/tmp_sbtsi.c
>> > >> > > @@ -0,0 +1,393 @@
>> > >> > > +/*
>> > >> > > + * AMD SBI Temperature Sensor Interface (SB-TSI)
>> > >> > > + *
>> > >> > > + * Copyright 2021 Google LLC
>> > >> > > + *
>> > >> > > + * This program is free software; you can redistribute it and/or
>> > >> modify it
>> > >> > > + * under the terms of the GNU General Public License as
>> published by
>> > >> the
>> > >> > > + * Free Software Foundation; either version 2 of the License, or
>> > >> > > + * (at your option) any later version.
>> > >> > > + *
>> > >> > > + * This program is distributed in the hope that it will be
>> useful,
>> > >> but
>> > >> > > WITHOUT
>> > >> > > + * ANY WARRANTY; without even the implied warranty of
>> > >> MERCHANTABILITY or
>> > >> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
>> > >> License
>> > >> > > + * for more details.
>> > >> > > + */
>> > >> > > +
>> > >> > > +#include "qemu/osdep.h"
>> > >> > > +#include "hw/i2c/smbus_slave.h"
>> > >> > > +#include "hw/irq.h"
>> > >> > > +#include "migration/vmstate.h"
>> > >> > > +#include "qapi/error.h"
>> > >> > > +#include "qapi/visitor.h"
>> > >> > > +#include "qemu/log.h"
>> > >> > > +#include "qemu/module.h"
>> > >> > > +#include "trace.h"
>> > >> > > +
>> > >> > > +#define TYPE_SBTSI "sbtsi"
>> > >> > > +#define SBTSI(obj) OBJECT_CHECK(SBTSIState, (obj), TYPE_SBTSI)
>> > >> > > +
>> > >> > > +/**
>> > >> > > + * SBTSIState:
>> > >> > > + * temperatures are in units of 0.125 degrees
>> > >> > > + * @temperature: Temperature
>> > >> > > + * @limit_low: Lowest temperature
>> > >> > > + * @limit_high: Highest temperature
>> > >> > > + * @status: The status register
>> > >> > > + * @config: The config register
>> > >> > > + * @alert_config: The config for alarm_l output.
>> > >> > > + * @addr: The address to read/write for the next cmd.
>> > >> > > + * @alarm: The alarm_l output pin (GPIO)
>> > >> > > + */
>> > >> > > +typedef struct SBTSIState {
>> > >> > > + SMBusDevice parent;
>> > >> > > +
>> > >> > > + uint32_t temperature;
>> > >> > > + uint32_t limit_low;
>> > >> > > + uint32_t limit_high;
>> > >> > > + uint8_t status;
>> > >> > > + uint8_t config;
>> > >> > > + uint8_t alert_config;
>> > >> > > + uint8_t addr;
>> > >> > > + qemu_irq alarm;
>> > >> > > +} SBTSIState;
>> > >> > > +
>> > >> > > +/*
>> > >> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
>> > >> registers
>> > >> > > are
>> > >> > > + * the integer part of a temperature value or limit, and "_DEC"
>> > >> registers
>> > >> > > are
>> > >> > > + * corresponding decimal parts.
>> > >> > > + */
>> > >> > > +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
>> > >> > > +#define SBTSI_REG_STATUS 0x02 /* RO */
>> > >> > > +#define SBTSI_REG_CONFIG 0x03 /* RO */
>> > >> > > +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
>> > >> > > +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
>> > >> > > +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
>> > >> > > +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
>> > >> > > +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
>> > >> > > +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
>> > >> > > +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
>> > >> > > +#define SBTSI_REG_MAN 0xFE /* RO */
>> > >> > > +#define SBTSI_REG_REV 0xFF /* RO */
>> > >> > > +
>> > >> > > +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
>> > >> > > +#define SBTSI_STATUS_LOW_ALERT BIT(3)
>> > >> > > +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
>> > >> > > +#define SBTSI_ALARM_EN BIT(0)
>> > >> > > +
>> > >> > > +#define SBTSI_LIMIT_LOW_DEFAULT (0)
>> > >> > > +#define SBTSI_LIMIT_HIGH_DEFAULT (560)
>> > >> > > +#define SBTSI_MAN_DEFAULT (0)
>> > >> > > +#define SBTSI_REV_DEFAULT (4)
>> > >> > > +#define SBTSI_ALARM_L "alarm_l"
>> > >> > > +
>> > >> > > +/* The temperature we stored are in units of 0.125 degrees. */
>> > >> > > +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
>> > >> > > +
>> > >> > > +/*
>> > >> > > + * The integer part and decimal of the temperature both 8 bits.
>> > >> > > + * Only the top 3 bits of the decimal parts are used.
>> > >> > > + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875
>> degrees.
>> > >> > > + */
>> > >> > > +#define SBTSI_TEMP_MAX 255875
>> > >> > > +
>> > >> > > +/* The integer part of the temperature in terms of 0.125
>> degrees. */
>> > >> > > +static uint8_t get_temp_int(uint32_t temp)
>> > >> > > +{
>> > >> > > + return temp >> 3;
>> > >> > > +}
>> > >> > > +
>> > >> > > +/*
>> > >> > > + * The decimal part of the temperature, in terms of 0.125
>> degrees.
>> > >> > > + * H/W store it in the top 3 bits so we shift it by 5.
>> > >> > > + */
>> > >> > > +static uint8_t get_temp_dec(uint32_t temp)
>> > >> > > +{
>> > >> > > + return (temp & 0x7) << 5;
>> > >> > > +}
>> > >> > > +
>> > >> > > +/*
>> > >> > > + * Compute the temperature using the integer and decimal part,
>> > >> > > + * in terms of 0.125 degrees. The decimal part are only the top
>> 3
>> > >> bits
>> > >> > > + * so we shift it by 5 here.
>> > >> > > + */
>> > >> > > +static uint32_t compute_temp(uint8_t integer, uint8_t decimal)
>> > >> > > +{
>> > >> > > + return (integer << 3) + (decimal >> 5);
>> > >> > > +}
>> > >> > > +
>> > >> > > +/* Compute new temp with new int part of the temperature. */
>> > >> > > +static uint32_t compute_temp_int(uint32_t temp, uint8_t integer)
>> > >> > > +{
>> > >> > > + return compute_temp(integer, get_temp_dec(temp));
>> > >> > > +}
>> > >> > > +
>> > >> > > +/* Compute new temp with new dec part of the temperature. */
>> > >> > > +static uint32_t compute_temp_dec(uint32_t temp, uint8_t decimal)
>> > >> > > +{
>> > >> > > + return compute_temp(get_temp_int(temp), decimal);
>> > >> > > +}
>> > >> > > +
>> > >> > > +/* The integer part of the temperature. */
>> > >> > > +static void sbtsi_update_status(SBTSIState *s)
>> > >> > > +{
>> > >> > > + s->status = 0;
>> > >> > > + if (s->alert_config & SBTSI_ALARM_EN) {
>> > >> > > + if (s->temperature >= s->limit_high) {
>> > >> > > + s->status |= SBTSI_STATUS_HIGH_ALERT;
>> > >> > > + }
>> > >> > > + if (s->temperature <= s->limit_low) {
>> > >> > > + s->status |= SBTSI_STATUS_LOW_ALERT;
>> > >> > > + }
>> > >> > > + }
>> > >> > > +}
>> > >> > > +
>> > >> > > +static void sbtsi_update_alarm(SBTSIState *s)
>> > >> > > +{
>> > >> > > + sbtsi_update_status(s);
>> > >> > > + if (s->status != 0 && !(s->config &
>> SBTSI_CONFIG_ALERT_MASK)) {
>> > >> > > + qemu_irq_raise(s->alarm);
>> > >> > > + } else {
>> > >> > > + qemu_irq_lower(s->alarm);
>> > >> > > + }
>> > >> > > +}
>> > >> > > +
>> > >> > > +static uint8_t sbtsi_read_byte(SMBusDevice *d)
>> > >> > > +{
>> > >> > > + SBTSIState *s = SBTSI(d);
>> > >> > > + uint8_t data = 0;
>> > >> > > +
>> > >> > > + switch (s->addr) {
>> > >> > > + case SBTSI_REG_TEMP_INT:
>> > >> > > + data = get_temp_int(s->temperature);
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_TEMP_DEC:
>> > >> > > + data = get_temp_dec(s->temperature);
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_TEMP_HIGH_INT:
>> > >> > > + data = get_temp_int(s->limit_high);
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_TEMP_LOW_INT:
>> > >> > > + data = get_temp_int(s->limit_low);
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_TEMP_HIGH_DEC:
>> > >> > > + data = get_temp_dec(s->limit_high);
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_TEMP_LOW_DEC:
>> > >> > > + data = get_temp_dec(s->limit_low);
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_CONFIG:
>> > >> > > + case SBTSI_REG_CONFIG_WR:
>> > >> > > + data = s->config;
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_STATUS:
>> > >> > > + sbtsi_update_alarm(s);
>> > >> > > + data = s->status;
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_ALERT_CONFIG:
>> > >> > > + data = s->alert_config;
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_MAN:
>> > >> > > + data = SBTSI_MAN_DEFAULT;
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_REV:
>> > >> > > + data = SBTSI_REV_DEFAULT;
>> > >> > > + break;
>> > >>
>> > >> Does this device do some sort of auto-increment on the address when
>> > >> reading/writing?
>> > >>
>> > >
>> > > +Hao Wu <wuhaotsh@google.com> - Please take a look at the above
>> > > question. I imagine it's a while since you've thought about it, but
>> please
>> > > double check :)
>> > > Thanks!
>> > >
>> > >
>> > >> Other than that possible issue, I don't see anything else, it's
>> pretty
>> > >> straightforward.
>> > >>
>> > >> > > +
>> > >> > > + default:
>> > >> > > + qemu_log_mask(LOG_GUEST_ERROR,
>> > >> > > + "%s: reading from invalid reg: 0x%02x\n",
>> > >> > > + __func__, s->addr);
>> > >> > > + break;
>> > >> > > + }
>> > >> > > +
>> > >> > > + trace_tmp_sbtsi_read_data(s->addr, data);
>> > >> > > + return data;
>> > >> > > +}
>> > >> > > +
>> > >> > > +static void sbtsi_write(SBTSIState *s, uint8_t data)
>> > >> > > +{
>> > >> > > + trace_tmp_sbtsi_write_data(s->addr, data);
>> > >> > > + switch (s->addr) {
>> > >> > > + case SBTSI_REG_CONFIG_WR:
>> > >> > > + s->config = data;
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_TEMP_HIGH_INT:
>> > >> > > + s->limit_high = compute_temp_int(s->limit_high, data);
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_TEMP_LOW_INT:
>> > >> > > + s->limit_low = compute_temp_int(s->limit_low, data);
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_TEMP_HIGH_DEC:
>> > >> > > + s->limit_high = compute_temp_dec(s->limit_high, data);
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_TEMP_LOW_DEC:
>> > >> > > + s->limit_low = compute_temp_dec(s->limit_low, data);
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_ALERT_CONFIG:
>> > >> > > + s->alert_config = data;
>> > >> > > + break;
>> > >> > > +
>> > >> > > + case SBTSI_REG_TEMP_INT:
>> > >> > > + case SBTSI_REG_TEMP_DEC:
>> > >> > > + case SBTSI_REG_CONFIG:
>> > >> > > + case SBTSI_REG_STATUS:
>> > >> > > + case SBTSI_REG_MAN:
>> > >> > > + case SBTSI_REG_REV:
>> > >> > > + qemu_log_mask(LOG_GUEST_ERROR,
>> > >> > > + "%s: writing to read only reg: 0x%02x data:
>> > >> 0x%02x\n",
>> > >> > > + __func__, s->addr, data);
>> > >> > > + break;
>> > >> > > +
>> > >> > > + default:
>> > >> > > + qemu_log_mask(LOG_GUEST_ERROR,
>> > >> > > + "%s: writing to invalid reg: 0x%02x data:
>> 0x%02x\n",
>> > >> > > + __func__, s->addr, data);
>> > >> > > + break;
>> > >> > > + }
>> > >> > > + sbtsi_update_alarm(s);
>> > >> > > +}
>> > >> > > +
>> > >> > > +static int sbtsi_write_data(SMBusDevice *d, uint8_t *buf,
>> uint8_t
>> > >> len)
>> > >> > > +{
>> > >> > > + SBTSIState *s = SBTSI(d);
>> > >> > > +
>> > >> > > + if (len == 0) {
>> > >> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: writing empty
>> data\n",
>> > >> > > __func__);
>> > >> > > + return -1;
>> > >> > > + }
>> > >> > > +
>> > >> > > + s->addr = buf[0];
>> > >> > > + if (len > 1) {
>> > >> > > + sbtsi_write(s, buf[1]);
>> > >> > > + if (len > 2) {
>> > >> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: extra data at
>> end\n",
>> > >> > > __func__);
>> > >> > > + }
>> > >> > > + }
>> > >> > > + return 0;
>> > >> > > +}
>> > >> > > +
>> > >> > > +/* Units are millidegrees. */
>> > >> > > +static void sbtsi_get_temperature(Object *obj, Visitor *v,
>> const char
>> > >> > > *name,
>> > >> > > + void *opaque, Error **errp)
>> > >> > > +{
>> > >> > > + SBTSIState *s = SBTSI(obj);
>> > >> > > + uint32_t temp = s->temperature *
>> SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
>> > >> > > +
>> > >> > > + visit_type_uint32(v, name, &temp, errp);
>> > >> > > +}
>> > >> > > +
>> > >> > > +/* Units are millidegrees. */
>> > >> > > +static void sbtsi_set_temperature(Object *obj, Visitor *v,
>> const char
>> > >> > > *name,
>> > >> > > + void *opaque, Error **errp)
>> > >> > > +{
>> > >> > > + SBTSIState *s = SBTSI(obj);
>> > >> > > + uint32_t temp;
>> > >> > > +
>> > >> > > + if (!visit_type_uint32(v, name, &temp, errp)) {
>> > >> > > + return;
>> > >> > > + }
>> > >> > > + if (temp > SBTSI_TEMP_MAX) {
>> > >> > > + error_setg(errp, "value %" PRIu32 ".%03" PRIu32 " C is
>> out of
>> > >> > > range",
>> > >> > > + temp / 1000, temp % 1000);
>> > >> > > + return;
>> > >> > > + }
>> > >> > > +
>> > >> > > + s->temperature = temp / SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
>> > >> > > + sbtsi_update_alarm(s);
>> > >> > > +}
>> > >> > > +
>> > >> > > +static int sbtsi_post_load(void *opaque, int version_id)
>> > >> > > +{
>> > >> > > + SBTSIState *s = opaque;
>> > >> > > +
>> > >> > > + sbtsi_update_alarm(s);
>> > >> > > + return 0;
>> > >> > > +}
>> > >> > > +
>> > >> > > +static const VMStateDescription vmstate_sbtsi = {
>> > >> > > + .name = "SBTSI",
>> > >> > > + .version_id = 0,
>> > >> > > + .minimum_version_id = 0,
>> > >> > > + .post_load = sbtsi_post_load,
>> > >> > > + .fields = (VMStateField[]) {
>> > >> > > + VMSTATE_UINT32(temperature, SBTSIState),
>> > >> > > + VMSTATE_UINT32(limit_low, SBTSIState),
>> > >> > > + VMSTATE_UINT32(limit_high, SBTSIState),
>> > >> > > + VMSTATE_UINT8(config, SBTSIState),
>> > >> > > + VMSTATE_UINT8(status, SBTSIState),
>> > >> > > + VMSTATE_UINT8(addr, SBTSIState),
>> > >> > > + VMSTATE_END_OF_LIST()
>> > >> > > + }
>> > >> > > +};
>> > >> > > +
>> > >> > > +static void sbtsi_enter_reset(Object *obj, ResetType type)
>> > >> > > +{
>> > >> > > + SBTSIState *s = SBTSI(obj);
>> > >> > > +
>> > >> > > + s->config = 0;
>> > >> > > + s->limit_low = SBTSI_LIMIT_LOW_DEFAULT;
>> > >> > > + s->limit_high = SBTSI_LIMIT_HIGH_DEFAULT;
>> > >> > > +}
>> > >> > > +
>> > >> > > +static void sbtsi_hold_reset(Object *obj)
>> > >> > > +{
>> > >> > > + SBTSIState *s = SBTSI(obj);
>> > >> > > +
>> > >> > > + qemu_irq_lower(s->alarm);
>> > >> > > +}
>> > >> > > +
>> > >> > > +static void sbtsi_init(Object *obj)
>> > >> > > +{
>> > >> > > + SBTSIState *s = SBTSI(obj);
>> > >> > > +
>> > >> > > + /* Current temperature in millidegrees. */
>> > >> > > + object_property_add(obj, "temperature", "uint32",
>> > >> > > + sbtsi_get_temperature,
>> sbtsi_set_temperature,
>> > >> > > + NULL, NULL);
>> > >> > > + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm,
>> SBTSI_ALARM_L,
>> > >> 0);
>> > >> > > +}
>> > >> > > +
>> > >> > > +static void sbtsi_class_init(ObjectClass *klass, void *data)
>> > >> > > +{
>> > >> > > + ResettableClass *rc = RESETTABLE_CLASS(klass);
>> > >> > > + DeviceClass *dc = DEVICE_CLASS(klass);
>> > >> > > + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
>> > >> > > +
>> > >> > > + dc->desc = "SB-TSI Temperature Sensor";
>> > >> > > + dc->vmsd = &vmstate_sbtsi;
>> > >> > > + k->write_data = sbtsi_write_data;
>> > >> > > + k->receive_byte = sbtsi_read_byte;
>> > >> > > + rc->phases.enter = sbtsi_enter_reset;
>> > >> > > + rc->phases.hold = sbtsi_hold_reset;
>> > >> > > +}
>> > >> > > +
>> > >> > > +static const TypeInfo sbtsi_info = {
>> > >> > > + .name = TYPE_SBTSI,
>> > >> > > + .parent = TYPE_SMBUS_DEVICE,
>> > >> > > + .instance_size = sizeof(SBTSIState),
>> > >> > > + .instance_init = sbtsi_init,
>> > >> > > + .class_init = sbtsi_class_init,
>> > >> > > +};
>> > >> > > +
>> > >> > > +static void sbtsi_register_types(void)
>> > >> > > +{
>> > >> > > + type_register_static(&sbtsi_info);
>> > >> > > +}
>> > >> > > +
>> > >> > > +type_init(sbtsi_register_types)
>> > >> > > diff --git a/hw/sensor/trace-events b/hw/sensor/trace-events
>> > >> > > new file mode 100644
>> > >> > > index 0000000000..21ab3809e2
>> > >> > > --- /dev/null
>> > >> > > +++ b/hw/sensor/trace-events
>> > >> > > @@ -0,0 +1,5 @@
>> > >> > > +# See docs/devel/tracing.rst for syntax documentation.
>> > >> > > +
>> > >> > > +# tmp_sbtsi.c
>> > >> > > +tmp_sbtsi_write_data(uint8_t addr, uint8_t value) "SBTSI write
>> > >> > > addr:0x%02x data: 0x%02x"
>> > >> > > +tmp_sbtsi_read_data(uint8_t addr, uint8_t value) "SBTSI read
>> > >> addr:0x%02x
>> > >> > > data: 0x%02x"
>> > >> > > diff --git a/hw/sensor/trace.h b/hw/sensor/trace.h
>> > >> > > new file mode 100644
>> > >> > > index 0000000000..e4721560b0
>> > >> > > --- /dev/null
>> > >> > > +++ b/hw/sensor/trace.h
>> > >> > > @@ -0,0 +1 @@
>> > >> > > +#include "trace/trace-hw_sensor.h"
>> > >> > > diff --git a/meson.build b/meson.build
>> > >> > > index 53065e96ec..f8ab0bf74e 100644
>> > >> > > --- a/meson.build
>> > >> > > +++ b/meson.build
>> > >> > > @@ -2494,6 +2494,7 @@ if have_system
>> > >> > > 'hw/rtc',
>> > >> > > 'hw/s390x',
>> > >> > > 'hw/scsi',
>> > >> > > + 'hw/sensor',
>> > >> > > 'hw/sd',
>> > >> > > 'hw/sh4',
>> > >> > > 'hw/sparc',
>> > >> > > diff --git a/tests/qtest/meson.build b/tests/qtest/meson.build
>> > >> > > index 37e1eaa449..d1a8c38f74 100644
>> > >> > > --- a/tests/qtest/meson.build
>> > >> > > +++ b/tests/qtest/meson.build
>> > >> > > @@ -254,6 +254,7 @@ qos_test_ss.add(
>> > >> > > 'spapr-phb-test.c',
>> > >> > > 'tmp105-test.c',
>> > >> > > 'emc141x-test.c',
>> > >> > > + 'tmp_sbtsi-test.c',
>> > >> > > 'usb-hcd-ohci-test.c',
>> > >> > > 'virtio-test.c',
>> > >> > > 'virtio-blk-test.c',
>> > >> > > diff --git a/tests/qtest/tmp_sbtsi-test.c
>> > >> b/tests/qtest/tmp_sbtsi-test.c
>> > >> > > new file mode 100644
>> > >> > > index 0000000000..7f5fafacc7
>> > >> > > --- /dev/null
>> > >> > > +++ b/tests/qtest/tmp_sbtsi-test.c
>> > >> > > @@ -0,0 +1,180 @@
>> > >> > > +/*
>> > >> > > + * QTests for the SBTSI temperature sensor
>> > >> > > + *
>> > >> > > + * Copyright 2020 Google LLC
>> > >> > > + *
>> > >> > > + * This program is free software; you can redistribute it and/or
>> > >> modify it
>> > >> > > + * under the terms of the GNU General Public License as
>> published by
>> > >> the
>> > >> > > + * Free Software Foundation; either version 2 of the License, or
>> > >> > > + * (at your option) any later version.
>> > >> > > + *
>> > >> > > + * This program is distributed in the hope that it will be
>> useful,
>> > >> but
>> > >> > > WITHOUT
>> > >> > > + * ANY WARRANTY; without even the implied warranty of
>> > >> MERCHANTABILITY or
>> > >> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
>> > >> License
>> > >> > > + * for more details.
>> > >> > > + */
>> > >> > > +
>> > >> > > +#include "qemu/osdep.h"
>> > >> > > +
>> > >> > > +#include "libqtest-single.h"
>> > >> > > +#include "libqos/qgraph.h"
>> > >> > > +#include "libqos/i2c.h"
>> > >> > > +#include "qapi/qmp/qdict.h"
>> > >> > > +#include "qemu/bitops.h"
>> > >> > > +
>> > >> > > +#define TEST_ID "sbtsi-test"
>> > >> > > +#define TEST_ADDR (0x4c)
>> > >> > > +
>> > >> > > +/*
>> > >> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
>> > >> registers
>> > >> > > are
>> > >> > > + * the integer part of a temperature value or limit, and "_DEC"
>> > >> registers
>> > >> > > are
>> > >> > > + * corresponding decimal parts.
>> > >> > > + */
>> > >> > > +#define REG_TEMP_INT 0x01 /* RO */
>> > >> > > +#define REG_STATUS 0x02 /* RO */
>> > >> > > +#define REG_CONFIG 0x03 /* RO */
>> > >> > > +#define REG_TEMP_HIGH_INT 0x07 /* RW */
>> > >> > > +#define REG_TEMP_LOW_INT 0x08 /* RW */
>> > >> > > +#define REG_CONFIG_WR 0x09 /* RW */
>> > >> > > +#define REG_TEMP_DEC 0x10 /* RO */
>> > >> > > +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
>> > >> > > +#define REG_TEMP_LOW_DEC 0x14 /* RW */
>> > >> > > +#define REG_ALERT_CONFIG 0xBF /* RW */
>> > >> > > +
>> > >> > > +#define STATUS_HIGH_ALERT BIT(4)
>> > >> > > +#define STATUS_LOW_ALERT BIT(3)
>> > >> > > +#define CONFIG_ALERT_MASK BIT(7)
>> > >> > > +#define ALARM_EN BIT(0)
>> > >> > > +
>> > >> > > +/* The temperature stored are in units of 0.125 degrees. */
>> > >> > > +#define TEMP_UNIT_IN_MILLIDEGREE 125
>> > >> > > +#define LIMIT_LOW (10500)
>> > >> > > +#define LIMIT_HIGH (55125)
>> > >> > > +
>> > >> > > +static uint32_t qmp_sbtsi_get_temperature(const char *id)
>> > >> > > +{
>> > >> > > + QDict *response;
>> > >> > > + int ret;
>> > >> > > +
>> > >> > > + response = qmp("{ 'execute': 'qom-get', 'arguments': {
>> 'path':
>> > >> %s, "
>> > >> > > + "'property': 'temperature' } }", id);
>> > >> > > + g_assert(qdict_haskey(response, "return"));
>> > >> > > + ret = (uint32_t)qdict_get_int(response, "return");
>> > >> > > + qobject_unref(response);
>> > >> > > + return ret;
>> > >> > > +}
>> > >> > > +
>> > >> > > +static void qmp_sbtsi_set_temperature(const char *id, uint32_t
>> value)
>> > >> > > +{
>> > >> > > + QDict *response;
>> > >> > > +
>> > >> > > + response = qmp("{ 'execute': 'qom-set', 'arguments': {
>> 'path':
>> > >> %s, "
>> > >> > > + "'property': 'temperature', 'value': %d }
>> }", id,
>> > >> > > value);
>> > >> > > + g_assert(qdict_haskey(response, "return"));
>> > >> > > + qobject_unref(response);
>> > >> > > +}
>> > >> > > +
>> > >> > > +/*
>> > >> > > + * Compute the temperature using the integer and decimal part
>> and
>> > >> return
>> > >> > > + * millidegrees. The decimal part are only the top 3 bits so we
>> > >> shift it
>> > >> > > by
>> > >> > > + * 5 here.
>> > >> > > + */
>> > >> > > +static uint32_t regs_to_temp(uint8_t integer, uint8_t decimal)
>> > >> > > +{
>> > >> > > + return ((integer << 3) + (decimal >> 5)) *
>> > >> TEMP_UNIT_IN_MILLIDEGREE;
>> > >> > > +}
>> > >> > > +
>> > >> > > +/*
>> > >> > > + * Compute the integer and decimal parts of the temperature in
>> > >> > > millidegrees.
>> > >> > > + * H/W store the decimal in the top 3 bits so we shift it by 5.
>> > >> > > + */
>> > >> > > +static void temp_to_regs(uint32_t temp, uint8_t *integer,
>> uint8_t
>> > >> > > *decimal)
>> > >> > > +{
>> > >> > > + temp /= TEMP_UNIT_IN_MILLIDEGREE;
>> > >> > > + *integer = temp >> 3;
>> > >> > > + *decimal = (temp & 0x7) << 5;
>> > >> > > +}
>> > >> > > +
>> > >> > > +static void tx_rx(void *obj, void *data, QGuestAllocator *alloc)
>> > >> > > +{
>> > >> > > + uint16_t value;
>> > >> > > + uint8_t integer, decimal;
>> > >> > > + QI2CDevice *i2cdev = (QI2CDevice *)obj;
>> > >> > > +
>> > >> > > + /* Test default values */
>> > >> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
>> > >> > > + g_assert_cmpuint(value, ==, 0);
>> > >> > > +
>> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
>> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
>> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 0);
>> > >> > > +
>> > >> > > + /* Test setting temperature */
>> > >> > > + qmp_sbtsi_set_temperature(TEST_ID, 20000);
>> > >> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
>> > >> > > + g_assert_cmpuint(value, ==, 20000);
>> > >> > > +
>> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
>> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
>> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 20000);
>> > >> > > +
>> > >> > > + /* Set alert mask in config */
>> > >> > > + i2c_set8(i2cdev, REG_CONFIG_WR, CONFIG_ALERT_MASK);
>> > >> > > + value = i2c_get8(i2cdev, REG_CONFIG);
>> > >> > > + g_assert_cmphex(value, ==, CONFIG_ALERT_MASK);
>> > >> > > + /* Enable alarm_en */
>> > >> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, ALARM_EN);
>> > >> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
>> > >> > > + g_assert_cmphex(value, ==, ALARM_EN);
>> > >> > > +
>> > >> > > + /* Test setting limits */
>> > >> > > + /* Limit low = 10.500 */
>> > >> > > + temp_to_regs(LIMIT_LOW, &integer, &decimal);
>> > >> > > + i2c_set8(i2cdev, REG_TEMP_LOW_INT, integer);
>> > >> > > + i2c_set8(i2cdev, REG_TEMP_LOW_DEC, decimal);
>> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_LOW_INT);
>> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_LOW_DEC);
>> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==,
>> LIMIT_LOW);
>> > >> > > + /* Limit high = 55.125 */
>> > >> > > + temp_to_regs(LIMIT_HIGH, &integer, &decimal);
>> > >> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_INT, integer);
>> > >> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_DEC, decimal);
>> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_HIGH_INT);
>> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_HIGH_DEC);
>> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==,
>> LIMIT_HIGH);
>> > >> > > + /* No alert is generated. */
>> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
>> > >> > > + g_assert_cmphex(value, ==, 0);
>> > >> > > +
>> > >> > > + /* Test alert for low temperature */
>> > >> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_LOW);
>> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
>> > >> > > + g_assert_cmphex(value, ==, STATUS_LOW_ALERT);
>> > >> > > +
>> > >> > > + /* Test alert for high temperature */
>> > >> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_HIGH);
>> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
>> > >> > > + g_assert_cmphex(value, ==, STATUS_HIGH_ALERT);
>> > >> > > +
>> > >> > > + /* Disable alarm_en */
>> > >> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, 0);
>> > >> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
>> > >> > > + g_assert_cmphex(value, ==, 0);
>> > >> > > + /* No alert when alarm_en is false. */
>> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
>> > >> > > + g_assert_cmphex(value, ==, 0);
>> > >> > > +}
>> > >> > > +
>> > >> > > +static void sbtsi_register_nodes(void)
>> > >> > > +{
>> > >> > > + QOSGraphEdgeOptions opts = {
>> > >> > > + .extra_device_opts = "id=" TEST_ID ",address=0x4c"
>> > >> > > + };
>> > >> > > + add_qi2c_address(&opts, &(QI2CAddress) { TEST_ADDR });
>> > >> > > +
>> > >> > > + qos_node_create_driver("sbtsi", i2c_device_create);
>> > >> > > + qos_node_consumes("sbtsi", "i2c-bus", &opts);
>> > >> > > +
>> > >> > > + qos_add_test("tx-rx", "sbtsi", tx_rx, NULL);
>> > >> > > +}
>> > >> > > +libqos_init(sbtsi_register_nodes);
>> > >> > > --
>> > >> >
>> > >> >
>> > >> > + Corey for i2c maintainer. The new sensor directory is mostly if
>> not
>> > >> > entirely i2c devices. I didn't create a maintainer entry for this
>> i2c
>> > >> > device, but I can if desired and send out a v2.
>> > >>
>> > >> Yeah, I guess I should be maintainer there. I'll queue up a change
>> for
>> > >> that. Thanks.
>> > >>
>> > >> -corey
>> > >>
>> > >> >
>> > >> >
>> > >> > > 2.34.1.575.g55b058a8bb-goog
>> > >> > >
>> > >> > >
>> > >>
>> > >
>>
>
[-- Attachment #2: Type: text/html, Size: 48982 bytes --]
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
2022-01-27 23:18 ` Patrick Venture
@ 2022-01-28 1:58 ` Corey Minyard
0 siblings, 0 replies; 15+ messages in thread
From: Corey Minyard @ 2022-01-28 1:58 UTC (permalink / raw)
To: Patrick Venture
Cc: Laurent Vivier, Corey Minyard, Thomas Huth, QEMU Developers,
Doug Evans, Hao Wu, Paolo Bonzini
On Thu, Jan 27, 2022 at 03:18:43PM -0800, Patrick Venture wrote:
> On Thu, Jan 27, 2022 at 10:20 AM Hao Wu <wuhaotsh@google.com> wrote:
>
> >
> > On Thu, Jan 27, 2022 at 6:55 AM Corey Minyard <cminyard@mvista.com> wrote:
> >
> >> On Wed, Jan 26, 2022 at 04:09:03PM -0800, Hao Wu wrote:
> >> > Hi,
> >> >
> >> > Sorry for the late reply. I'm not sure what "auto-increment" means here.
> >>
> >> The question is: When a value is read, does the address automatically
> >> increment. I2C devices very often do this. If you do a multi-byte
> >> read, they often will read the value from address 0, then from address
> >> 1, etc. Same for writes.
> >>
> > The datasheet does not suggest such behavior could happen.
> >
> >>
> >> > The kernel driver at
> >> > https://lkml.org/lkml/2020/12/11/968
> >> > only has byte-size read/write operations, so I don't see a problem here.
> >> > The values are extracted
> >> > from the datasheet.
> >>
> >> The *Linux* kernel driver my only do byte-size operations, but other
> >> kernels may work different, and the Linux kernel may change. You have
> >> to implement from the datasheet, not the device driver.
> >>
> > The implementation is already according to the datasheet.
> >
> >> Thanks,
> >>
> >> -corey
> >>
> >>
> I have to send out a new patchset to include my signature block since I'm
> sending a patch Hao wrote. Laurent pointed this out to me in a different
> patch series.
>
> From this exchange, I don't think there are other changes for v2. Please
> let me know if that's false.
Yes, we are good. It's a little surprising, hopefully we don't have to
fix it in the future if it works that way the datasheet didn't say so.
Acked-by: Corey Minyard <cminyard@mvista.com>
>
> Thanks,
> Patrick
>
>
> > >
> >> > On Tue, Jan 18, 2022 at 9:10 AM Patrick Venture <venture@google.com>
> >> wrote:
> >> >
> >> > >
> >> > >
> >> > > On Mon, Jan 17, 2022 at 6:05 AM Corey Minyard <cminyard@mvista.com>
> >> wrote:
> >> > >
> >> > >> On Sun, Jan 09, 2022 at 06:17:34PM -0800, Patrick Venture wrote:
> >> > >> > On Fri, Jan 7, 2022 at 7:04 PM Patrick Venture <venture@google.com
> >> >
> >> > >> wrote:
> >> > >> >
> >> > >> > > From: Hao Wu <wuhaotsh@google.com>
> >> > >> > >
> >> > >> > > SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
> >> > >> > > interface that reports AMD SoC's Ttcl (normalized temperature),
> >> > >> > > and resembles a typical 8-pin remote temperature sensor's I2C
> >> > >> interface
> >> > >> > > to BMC.
> >> > >> > >
> >> > >> > > This patch implements a basic AMD SB-TSI sensor that is
> >> > >> > > compatible with the open-source data sheet from AMD and Linux
> >> > >> > > kernel driver.
> >> > >> > >
> >> > >> > > Reference:
> >> > >> > > Linux kernel driver:
> >> > >> > > https://lkml.org/lkml/2020/12/11/968
> >> > >> > > Register Map:
> >> > >> > > https://developer.amd.com/wp-content/resources/56255_3_03.PDF
> >> > >> > > (Chapter 6)
> >> > >> > >
> >> > >> > > Signed-off-by: Hao Wu <wuhaotsh@google.com>
> >> > >> > > Reviewed-by: Doug Evans <dje@google.com>
> >> > >> > > ---
> >> > >> > > hw/sensor/Kconfig | 4 +
> >> > >> > > hw/sensor/meson.build | 1 +
> >> > >> > > hw/sensor/tmp_sbtsi.c | 393
> >> > >> +++++++++++++++++++++++++++++++++++
> >> > >> > > hw/sensor/trace-events | 5 +
> >> > >> > > hw/sensor/trace.h | 1 +
> >> > >> > > meson.build | 1 +
> >> > >> > > tests/qtest/meson.build | 1 +
> >> > >> > > tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
> >> > >> > > 8 files changed, 586 insertions(+)
> >> > >> > > create mode 100644 hw/sensor/tmp_sbtsi.c
> >> > >> > > create mode 100644 hw/sensor/trace-events
> >> > >> > > create mode 100644 hw/sensor/trace.h
> >> > >> > > create mode 100644 tests/qtest/tmp_sbtsi-test.c
> >> > >> > >
> >> > >> > > diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
> >> > >> > > index 9c8a049b06..27f6f79c84 100644
> >> > >> > > --- a/hw/sensor/Kconfig
> >> > >> > > +++ b/hw/sensor/Kconfig
> >> > >> > > @@ -21,3 +21,7 @@ config ADM1272
> >> > >> > > config MAX34451
> >> > >> > > bool
> >> > >> > > depends on I2C
> >> > >> > > +
> >> > >> > > +config AMDSBTSI
> >> > >> > > + bool
> >> > >> > > + depends on I2C
> >> > >> > > diff --git a/hw/sensor/meson.build b/hw/sensor/meson.build
> >> > >> > > index 059c4ca935..f7b0e645eb 100644
> >> > >> > > --- a/hw/sensor/meson.build
> >> > >> > > +++ b/hw/sensor/meson.build
> >> > >> > > @@ -4,3 +4,4 @@ softmmu_ss.add(when: 'CONFIG_DPS310', if_true:
> >> > >> > > files('dps310.c'))
> >> > >> > > softmmu_ss.add(when: 'CONFIG_EMC141X', if_true:
> >> files('emc141x.c'))
> >> > >> > > softmmu_ss.add(when: 'CONFIG_ADM1272', if_true:
> >> files('adm1272.c'))
> >> > >> > > softmmu_ss.add(when: 'CONFIG_MAX34451', if_true:
> >> files('max34451.c'))
> >> > >> > > +softmmu_ss.add(when: 'CONFIG_AMDSBTSI', if_true:
> >> > >> files('tmp_sbtsi.c'))
> >> > >> > > diff --git a/hw/sensor/tmp_sbtsi.c b/hw/sensor/tmp_sbtsi.c
> >> > >> > > new file mode 100644
> >> > >> > > index 0000000000..b68c7ebf61
> >> > >> > > --- /dev/null
> >> > >> > > +++ b/hw/sensor/tmp_sbtsi.c
> >> > >> > > @@ -0,0 +1,393 @@
> >> > >> > > +/*
> >> > >> > > + * AMD SBI Temperature Sensor Interface (SB-TSI)
> >> > >> > > + *
> >> > >> > > + * Copyright 2021 Google LLC
> >> > >> > > + *
> >> > >> > > + * This program is free software; you can redistribute it and/or
> >> > >> modify it
> >> > >> > > + * under the terms of the GNU General Public License as
> >> published by
> >> > >> the
> >> > >> > > + * Free Software Foundation; either version 2 of the License, or
> >> > >> > > + * (at your option) any later version.
> >> > >> > > + *
> >> > >> > > + * This program is distributed in the hope that it will be
> >> useful,
> >> > >> but
> >> > >> > > WITHOUT
> >> > >> > > + * ANY WARRANTY; without even the implied warranty of
> >> > >> MERCHANTABILITY or
> >> > >> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> >> > >> License
> >> > >> > > + * for more details.
> >> > >> > > + */
> >> > >> > > +
> >> > >> > > +#include "qemu/osdep.h"
> >> > >> > > +#include "hw/i2c/smbus_slave.h"
> >> > >> > > +#include "hw/irq.h"
> >> > >> > > +#include "migration/vmstate.h"
> >> > >> > > +#include "qapi/error.h"
> >> > >> > > +#include "qapi/visitor.h"
> >> > >> > > +#include "qemu/log.h"
> >> > >> > > +#include "qemu/module.h"
> >> > >> > > +#include "trace.h"
> >> > >> > > +
> >> > >> > > +#define TYPE_SBTSI "sbtsi"
> >> > >> > > +#define SBTSI(obj) OBJECT_CHECK(SBTSIState, (obj), TYPE_SBTSI)
> >> > >> > > +
> >> > >> > > +/**
> >> > >> > > + * SBTSIState:
> >> > >> > > + * temperatures are in units of 0.125 degrees
> >> > >> > > + * @temperature: Temperature
> >> > >> > > + * @limit_low: Lowest temperature
> >> > >> > > + * @limit_high: Highest temperature
> >> > >> > > + * @status: The status register
> >> > >> > > + * @config: The config register
> >> > >> > > + * @alert_config: The config for alarm_l output.
> >> > >> > > + * @addr: The address to read/write for the next cmd.
> >> > >> > > + * @alarm: The alarm_l output pin (GPIO)
> >> > >> > > + */
> >> > >> > > +typedef struct SBTSIState {
> >> > >> > > + SMBusDevice parent;
> >> > >> > > +
> >> > >> > > + uint32_t temperature;
> >> > >> > > + uint32_t limit_low;
> >> > >> > > + uint32_t limit_high;
> >> > >> > > + uint8_t status;
> >> > >> > > + uint8_t config;
> >> > >> > > + uint8_t alert_config;
> >> > >> > > + uint8_t addr;
> >> > >> > > + qemu_irq alarm;
> >> > >> > > +} SBTSIState;
> >> > >> > > +
> >> > >> > > +/*
> >> > >> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
> >> > >> registers
> >> > >> > > are
> >> > >> > > + * the integer part of a temperature value or limit, and "_DEC"
> >> > >> registers
> >> > >> > > are
> >> > >> > > + * corresponding decimal parts.
> >> > >> > > + */
> >> > >> > > +#define SBTSI_REG_TEMP_INT 0x01 /* RO */
> >> > >> > > +#define SBTSI_REG_STATUS 0x02 /* RO */
> >> > >> > > +#define SBTSI_REG_CONFIG 0x03 /* RO */
> >> > >> > > +#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
> >> > >> > > +#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
> >> > >> > > +#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
> >> > >> > > +#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
> >> > >> > > +#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
> >> > >> > > +#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
> >> > >> > > +#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
> >> > >> > > +#define SBTSI_REG_MAN 0xFE /* RO */
> >> > >> > > +#define SBTSI_REG_REV 0xFF /* RO */
> >> > >> > > +
> >> > >> > > +#define SBTSI_STATUS_HIGH_ALERT BIT(4)
> >> > >> > > +#define SBTSI_STATUS_LOW_ALERT BIT(3)
> >> > >> > > +#define SBTSI_CONFIG_ALERT_MASK BIT(7)
> >> > >> > > +#define SBTSI_ALARM_EN BIT(0)
> >> > >> > > +
> >> > >> > > +#define SBTSI_LIMIT_LOW_DEFAULT (0)
> >> > >> > > +#define SBTSI_LIMIT_HIGH_DEFAULT (560)
> >> > >> > > +#define SBTSI_MAN_DEFAULT (0)
> >> > >> > > +#define SBTSI_REV_DEFAULT (4)
> >> > >> > > +#define SBTSI_ALARM_L "alarm_l"
> >> > >> > > +
> >> > >> > > +/* The temperature we stored are in units of 0.125 degrees. */
> >> > >> > > +#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
> >> > >> > > +
> >> > >> > > +/*
> >> > >> > > + * The integer part and decimal of the temperature both 8 bits.
> >> > >> > > + * Only the top 3 bits of the decimal parts are used.
> >> > >> > > + * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875
> >> degrees.
> >> > >> > > + */
> >> > >> > > +#define SBTSI_TEMP_MAX 255875
> >> > >> > > +
> >> > >> > > +/* The integer part of the temperature in terms of 0.125
> >> degrees. */
> >> > >> > > +static uint8_t get_temp_int(uint32_t temp)
> >> > >> > > +{
> >> > >> > > + return temp >> 3;
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +/*
> >> > >> > > + * The decimal part of the temperature, in terms of 0.125
> >> degrees.
> >> > >> > > + * H/W store it in the top 3 bits so we shift it by 5.
> >> > >> > > + */
> >> > >> > > +static uint8_t get_temp_dec(uint32_t temp)
> >> > >> > > +{
> >> > >> > > + return (temp & 0x7) << 5;
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +/*
> >> > >> > > + * Compute the temperature using the integer and decimal part,
> >> > >> > > + * in terms of 0.125 degrees. The decimal part are only the top
> >> 3
> >> > >> bits
> >> > >> > > + * so we shift it by 5 here.
> >> > >> > > + */
> >> > >> > > +static uint32_t compute_temp(uint8_t integer, uint8_t decimal)
> >> > >> > > +{
> >> > >> > > + return (integer << 3) + (decimal >> 5);
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +/* Compute new temp with new int part of the temperature. */
> >> > >> > > +static uint32_t compute_temp_int(uint32_t temp, uint8_t integer)
> >> > >> > > +{
> >> > >> > > + return compute_temp(integer, get_temp_dec(temp));
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +/* Compute new temp with new dec part of the temperature. */
> >> > >> > > +static uint32_t compute_temp_dec(uint32_t temp, uint8_t decimal)
> >> > >> > > +{
> >> > >> > > + return compute_temp(get_temp_int(temp), decimal);
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +/* The integer part of the temperature. */
> >> > >> > > +static void sbtsi_update_status(SBTSIState *s)
> >> > >> > > +{
> >> > >> > > + s->status = 0;
> >> > >> > > + if (s->alert_config & SBTSI_ALARM_EN) {
> >> > >> > > + if (s->temperature >= s->limit_high) {
> >> > >> > > + s->status |= SBTSI_STATUS_HIGH_ALERT;
> >> > >> > > + }
> >> > >> > > + if (s->temperature <= s->limit_low) {
> >> > >> > > + s->status |= SBTSI_STATUS_LOW_ALERT;
> >> > >> > > + }
> >> > >> > > + }
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static void sbtsi_update_alarm(SBTSIState *s)
> >> > >> > > +{
> >> > >> > > + sbtsi_update_status(s);
> >> > >> > > + if (s->status != 0 && !(s->config &
> >> SBTSI_CONFIG_ALERT_MASK)) {
> >> > >> > > + qemu_irq_raise(s->alarm);
> >> > >> > > + } else {
> >> > >> > > + qemu_irq_lower(s->alarm);
> >> > >> > > + }
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static uint8_t sbtsi_read_byte(SMBusDevice *d)
> >> > >> > > +{
> >> > >> > > + SBTSIState *s = SBTSI(d);
> >> > >> > > + uint8_t data = 0;
> >> > >> > > +
> >> > >> > > + switch (s->addr) {
> >> > >> > > + case SBTSI_REG_TEMP_INT:
> >> > >> > > + data = get_temp_int(s->temperature);
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_TEMP_DEC:
> >> > >> > > + data = get_temp_dec(s->temperature);
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_TEMP_HIGH_INT:
> >> > >> > > + data = get_temp_int(s->limit_high);
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_TEMP_LOW_INT:
> >> > >> > > + data = get_temp_int(s->limit_low);
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_TEMP_HIGH_DEC:
> >> > >> > > + data = get_temp_dec(s->limit_high);
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_TEMP_LOW_DEC:
> >> > >> > > + data = get_temp_dec(s->limit_low);
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_CONFIG:
> >> > >> > > + case SBTSI_REG_CONFIG_WR:
> >> > >> > > + data = s->config;
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_STATUS:
> >> > >> > > + sbtsi_update_alarm(s);
> >> > >> > > + data = s->status;
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_ALERT_CONFIG:
> >> > >> > > + data = s->alert_config;
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_MAN:
> >> > >> > > + data = SBTSI_MAN_DEFAULT;
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_REV:
> >> > >> > > + data = SBTSI_REV_DEFAULT;
> >> > >> > > + break;
> >> > >>
> >> > >> Does this device do some sort of auto-increment on the address when
> >> > >> reading/writing?
> >> > >>
> >> > >
> >> > > +Hao Wu <wuhaotsh@google.com> - Please take a look at the above
> >> > > question. I imagine it's a while since you've thought about it, but
> >> please
> >> > > double check :)
> >> > > Thanks!
> >> > >
> >> > >
> >> > >> Other than that possible issue, I don't see anything else, it's
> >> pretty
> >> > >> straightforward.
> >> > >>
> >> > >> > > +
> >> > >> > > + default:
> >> > >> > > + qemu_log_mask(LOG_GUEST_ERROR,
> >> > >> > > + "%s: reading from invalid reg: 0x%02x\n",
> >> > >> > > + __func__, s->addr);
> >> > >> > > + break;
> >> > >> > > + }
> >> > >> > > +
> >> > >> > > + trace_tmp_sbtsi_read_data(s->addr, data);
> >> > >> > > + return data;
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static void sbtsi_write(SBTSIState *s, uint8_t data)
> >> > >> > > +{
> >> > >> > > + trace_tmp_sbtsi_write_data(s->addr, data);
> >> > >> > > + switch (s->addr) {
> >> > >> > > + case SBTSI_REG_CONFIG_WR:
> >> > >> > > + s->config = data;
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_TEMP_HIGH_INT:
> >> > >> > > + s->limit_high = compute_temp_int(s->limit_high, data);
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_TEMP_LOW_INT:
> >> > >> > > + s->limit_low = compute_temp_int(s->limit_low, data);
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_TEMP_HIGH_DEC:
> >> > >> > > + s->limit_high = compute_temp_dec(s->limit_high, data);
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_TEMP_LOW_DEC:
> >> > >> > > + s->limit_low = compute_temp_dec(s->limit_low, data);
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_ALERT_CONFIG:
> >> > >> > > + s->alert_config = data;
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + case SBTSI_REG_TEMP_INT:
> >> > >> > > + case SBTSI_REG_TEMP_DEC:
> >> > >> > > + case SBTSI_REG_CONFIG:
> >> > >> > > + case SBTSI_REG_STATUS:
> >> > >> > > + case SBTSI_REG_MAN:
> >> > >> > > + case SBTSI_REG_REV:
> >> > >> > > + qemu_log_mask(LOG_GUEST_ERROR,
> >> > >> > > + "%s: writing to read only reg: 0x%02x data:
> >> > >> 0x%02x\n",
> >> > >> > > + __func__, s->addr, data);
> >> > >> > > + break;
> >> > >> > > +
> >> > >> > > + default:
> >> > >> > > + qemu_log_mask(LOG_GUEST_ERROR,
> >> > >> > > + "%s: writing to invalid reg: 0x%02x data:
> >> 0x%02x\n",
> >> > >> > > + __func__, s->addr, data);
> >> > >> > > + break;
> >> > >> > > + }
> >> > >> > > + sbtsi_update_alarm(s);
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static int sbtsi_write_data(SMBusDevice *d, uint8_t *buf,
> >> uint8_t
> >> > >> len)
> >> > >> > > +{
> >> > >> > > + SBTSIState *s = SBTSI(d);
> >> > >> > > +
> >> > >> > > + if (len == 0) {
> >> > >> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: writing empty
> >> data\n",
> >> > >> > > __func__);
> >> > >> > > + return -1;
> >> > >> > > + }
> >> > >> > > +
> >> > >> > > + s->addr = buf[0];
> >> > >> > > + if (len > 1) {
> >> > >> > > + sbtsi_write(s, buf[1]);
> >> > >> > > + if (len > 2) {
> >> > >> > > + qemu_log_mask(LOG_GUEST_ERROR, "%s: extra data at
> >> end\n",
> >> > >> > > __func__);
> >> > >> > > + }
> >> > >> > > + }
> >> > >> > > + return 0;
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +/* Units are millidegrees. */
> >> > >> > > +static void sbtsi_get_temperature(Object *obj, Visitor *v,
> >> const char
> >> > >> > > *name,
> >> > >> > > + void *opaque, Error **errp)
> >> > >> > > +{
> >> > >> > > + SBTSIState *s = SBTSI(obj);
> >> > >> > > + uint32_t temp = s->temperature *
> >> SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> >> > >> > > +
> >> > >> > > + visit_type_uint32(v, name, &temp, errp);
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +/* Units are millidegrees. */
> >> > >> > > +static void sbtsi_set_temperature(Object *obj, Visitor *v,
> >> const char
> >> > >> > > *name,
> >> > >> > > + void *opaque, Error **errp)
> >> > >> > > +{
> >> > >> > > + SBTSIState *s = SBTSI(obj);
> >> > >> > > + uint32_t temp;
> >> > >> > > +
> >> > >> > > + if (!visit_type_uint32(v, name, &temp, errp)) {
> >> > >> > > + return;
> >> > >> > > + }
> >> > >> > > + if (temp > SBTSI_TEMP_MAX) {
> >> > >> > > + error_setg(errp, "value %" PRIu32 ".%03" PRIu32 " C is
> >> out of
> >> > >> > > range",
> >> > >> > > + temp / 1000, temp % 1000);
> >> > >> > > + return;
> >> > >> > > + }
> >> > >> > > +
> >> > >> > > + s->temperature = temp / SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
> >> > >> > > + sbtsi_update_alarm(s);
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static int sbtsi_post_load(void *opaque, int version_id)
> >> > >> > > +{
> >> > >> > > + SBTSIState *s = opaque;
> >> > >> > > +
> >> > >> > > + sbtsi_update_alarm(s);
> >> > >> > > + return 0;
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static const VMStateDescription vmstate_sbtsi = {
> >> > >> > > + .name = "SBTSI",
> >> > >> > > + .version_id = 0,
> >> > >> > > + .minimum_version_id = 0,
> >> > >> > > + .post_load = sbtsi_post_load,
> >> > >> > > + .fields = (VMStateField[]) {
> >> > >> > > + VMSTATE_UINT32(temperature, SBTSIState),
> >> > >> > > + VMSTATE_UINT32(limit_low, SBTSIState),
> >> > >> > > + VMSTATE_UINT32(limit_high, SBTSIState),
> >> > >> > > + VMSTATE_UINT8(config, SBTSIState),
> >> > >> > > + VMSTATE_UINT8(status, SBTSIState),
> >> > >> > > + VMSTATE_UINT8(addr, SBTSIState),
> >> > >> > > + VMSTATE_END_OF_LIST()
> >> > >> > > + }
> >> > >> > > +};
> >> > >> > > +
> >> > >> > > +static void sbtsi_enter_reset(Object *obj, ResetType type)
> >> > >> > > +{
> >> > >> > > + SBTSIState *s = SBTSI(obj);
> >> > >> > > +
> >> > >> > > + s->config = 0;
> >> > >> > > + s->limit_low = SBTSI_LIMIT_LOW_DEFAULT;
> >> > >> > > + s->limit_high = SBTSI_LIMIT_HIGH_DEFAULT;
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static void sbtsi_hold_reset(Object *obj)
> >> > >> > > +{
> >> > >> > > + SBTSIState *s = SBTSI(obj);
> >> > >> > > +
> >> > >> > > + qemu_irq_lower(s->alarm);
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static void sbtsi_init(Object *obj)
> >> > >> > > +{
> >> > >> > > + SBTSIState *s = SBTSI(obj);
> >> > >> > > +
> >> > >> > > + /* Current temperature in millidegrees. */
> >> > >> > > + object_property_add(obj, "temperature", "uint32",
> >> > >> > > + sbtsi_get_temperature,
> >> sbtsi_set_temperature,
> >> > >> > > + NULL, NULL);
> >> > >> > > + qdev_init_gpio_out_named(DEVICE(obj), &s->alarm,
> >> SBTSI_ALARM_L,
> >> > >> 0);
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static void sbtsi_class_init(ObjectClass *klass, void *data)
> >> > >> > > +{
> >> > >> > > + ResettableClass *rc = RESETTABLE_CLASS(klass);
> >> > >> > > + DeviceClass *dc = DEVICE_CLASS(klass);
> >> > >> > > + SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
> >> > >> > > +
> >> > >> > > + dc->desc = "SB-TSI Temperature Sensor";
> >> > >> > > + dc->vmsd = &vmstate_sbtsi;
> >> > >> > > + k->write_data = sbtsi_write_data;
> >> > >> > > + k->receive_byte = sbtsi_read_byte;
> >> > >> > > + rc->phases.enter = sbtsi_enter_reset;
> >> > >> > > + rc->phases.hold = sbtsi_hold_reset;
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static const TypeInfo sbtsi_info = {
> >> > >> > > + .name = TYPE_SBTSI,
> >> > >> > > + .parent = TYPE_SMBUS_DEVICE,
> >> > >> > > + .instance_size = sizeof(SBTSIState),
> >> > >> > > + .instance_init = sbtsi_init,
> >> > >> > > + .class_init = sbtsi_class_init,
> >> > >> > > +};
> >> > >> > > +
> >> > >> > > +static void sbtsi_register_types(void)
> >> > >> > > +{
> >> > >> > > + type_register_static(&sbtsi_info);
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +type_init(sbtsi_register_types)
> >> > >> > > diff --git a/hw/sensor/trace-events b/hw/sensor/trace-events
> >> > >> > > new file mode 100644
> >> > >> > > index 0000000000..21ab3809e2
> >> > >> > > --- /dev/null
> >> > >> > > +++ b/hw/sensor/trace-events
> >> > >> > > @@ -0,0 +1,5 @@
> >> > >> > > +# See docs/devel/tracing.rst for syntax documentation.
> >> > >> > > +
> >> > >> > > +# tmp_sbtsi.c
> >> > >> > > +tmp_sbtsi_write_data(uint8_t addr, uint8_t value) "SBTSI write
> >> > >> > > addr:0x%02x data: 0x%02x"
> >> > >> > > +tmp_sbtsi_read_data(uint8_t addr, uint8_t value) "SBTSI read
> >> > >> addr:0x%02x
> >> > >> > > data: 0x%02x"
> >> > >> > > diff --git a/hw/sensor/trace.h b/hw/sensor/trace.h
> >> > >> > > new file mode 100644
> >> > >> > > index 0000000000..e4721560b0
> >> > >> > > --- /dev/null
> >> > >> > > +++ b/hw/sensor/trace.h
> >> > >> > > @@ -0,0 +1 @@
> >> > >> > > +#include "trace/trace-hw_sensor.h"
> >> > >> > > diff --git a/meson.build b/meson.build
> >> > >> > > index 53065e96ec..f8ab0bf74e 100644
> >> > >> > > --- a/meson.build
> >> > >> > > +++ b/meson.build
> >> > >> > > @@ -2494,6 +2494,7 @@ if have_system
> >> > >> > > 'hw/rtc',
> >> > >> > > 'hw/s390x',
> >> > >> > > 'hw/scsi',
> >> > >> > > + 'hw/sensor',
> >> > >> > > 'hw/sd',
> >> > >> > > 'hw/sh4',
> >> > >> > > 'hw/sparc',
> >> > >> > > diff --git a/tests/qtest/meson.build b/tests/qtest/meson.build
> >> > >> > > index 37e1eaa449..d1a8c38f74 100644
> >> > >> > > --- a/tests/qtest/meson.build
> >> > >> > > +++ b/tests/qtest/meson.build
> >> > >> > > @@ -254,6 +254,7 @@ qos_test_ss.add(
> >> > >> > > 'spapr-phb-test.c',
> >> > >> > > 'tmp105-test.c',
> >> > >> > > 'emc141x-test.c',
> >> > >> > > + 'tmp_sbtsi-test.c',
> >> > >> > > 'usb-hcd-ohci-test.c',
> >> > >> > > 'virtio-test.c',
> >> > >> > > 'virtio-blk-test.c',
> >> > >> > > diff --git a/tests/qtest/tmp_sbtsi-test.c
> >> > >> b/tests/qtest/tmp_sbtsi-test.c
> >> > >> > > new file mode 100644
> >> > >> > > index 0000000000..7f5fafacc7
> >> > >> > > --- /dev/null
> >> > >> > > +++ b/tests/qtest/tmp_sbtsi-test.c
> >> > >> > > @@ -0,0 +1,180 @@
> >> > >> > > +/*
> >> > >> > > + * QTests for the SBTSI temperature sensor
> >> > >> > > + *
> >> > >> > > + * Copyright 2020 Google LLC
> >> > >> > > + *
> >> > >> > > + * This program is free software; you can redistribute it and/or
> >> > >> modify it
> >> > >> > > + * under the terms of the GNU General Public License as
> >> published by
> >> > >> the
> >> > >> > > + * Free Software Foundation; either version 2 of the License, or
> >> > >> > > + * (at your option) any later version.
> >> > >> > > + *
> >> > >> > > + * This program is distributed in the hope that it will be
> >> useful,
> >> > >> but
> >> > >> > > WITHOUT
> >> > >> > > + * ANY WARRANTY; without even the implied warranty of
> >> > >> MERCHANTABILITY or
> >> > >> > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> >> > >> License
> >> > >> > > + * for more details.
> >> > >> > > + */
> >> > >> > > +
> >> > >> > > +#include "qemu/osdep.h"
> >> > >> > > +
> >> > >> > > +#include "libqtest-single.h"
> >> > >> > > +#include "libqos/qgraph.h"
> >> > >> > > +#include "libqos/i2c.h"
> >> > >> > > +#include "qapi/qmp/qdict.h"
> >> > >> > > +#include "qemu/bitops.h"
> >> > >> > > +
> >> > >> > > +#define TEST_ID "sbtsi-test"
> >> > >> > > +#define TEST_ADDR (0x4c)
> >> > >> > > +
> >> > >> > > +/*
> >> > >> > > + * SB-TSI registers only support SMBus byte data access. "_INT"
> >> > >> registers
> >> > >> > > are
> >> > >> > > + * the integer part of a temperature value or limit, and "_DEC"
> >> > >> registers
> >> > >> > > are
> >> > >> > > + * corresponding decimal parts.
> >> > >> > > + */
> >> > >> > > +#define REG_TEMP_INT 0x01 /* RO */
> >> > >> > > +#define REG_STATUS 0x02 /* RO */
> >> > >> > > +#define REG_CONFIG 0x03 /* RO */
> >> > >> > > +#define REG_TEMP_HIGH_INT 0x07 /* RW */
> >> > >> > > +#define REG_TEMP_LOW_INT 0x08 /* RW */
> >> > >> > > +#define REG_CONFIG_WR 0x09 /* RW */
> >> > >> > > +#define REG_TEMP_DEC 0x10 /* RO */
> >> > >> > > +#define REG_TEMP_HIGH_DEC 0x13 /* RW */
> >> > >> > > +#define REG_TEMP_LOW_DEC 0x14 /* RW */
> >> > >> > > +#define REG_ALERT_CONFIG 0xBF /* RW */
> >> > >> > > +
> >> > >> > > +#define STATUS_HIGH_ALERT BIT(4)
> >> > >> > > +#define STATUS_LOW_ALERT BIT(3)
> >> > >> > > +#define CONFIG_ALERT_MASK BIT(7)
> >> > >> > > +#define ALARM_EN BIT(0)
> >> > >> > > +
> >> > >> > > +/* The temperature stored are in units of 0.125 degrees. */
> >> > >> > > +#define TEMP_UNIT_IN_MILLIDEGREE 125
> >> > >> > > +#define LIMIT_LOW (10500)
> >> > >> > > +#define LIMIT_HIGH (55125)
> >> > >> > > +
> >> > >> > > +static uint32_t qmp_sbtsi_get_temperature(const char *id)
> >> > >> > > +{
> >> > >> > > + QDict *response;
> >> > >> > > + int ret;
> >> > >> > > +
> >> > >> > > + response = qmp("{ 'execute': 'qom-get', 'arguments': {
> >> 'path':
> >> > >> %s, "
> >> > >> > > + "'property': 'temperature' } }", id);
> >> > >> > > + g_assert(qdict_haskey(response, "return"));
> >> > >> > > + ret = (uint32_t)qdict_get_int(response, "return");
> >> > >> > > + qobject_unref(response);
> >> > >> > > + return ret;
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static void qmp_sbtsi_set_temperature(const char *id, uint32_t
> >> value)
> >> > >> > > +{
> >> > >> > > + QDict *response;
> >> > >> > > +
> >> > >> > > + response = qmp("{ 'execute': 'qom-set', 'arguments': {
> >> 'path':
> >> > >> %s, "
> >> > >> > > + "'property': 'temperature', 'value': %d }
> >> }", id,
> >> > >> > > value);
> >> > >> > > + g_assert(qdict_haskey(response, "return"));
> >> > >> > > + qobject_unref(response);
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +/*
> >> > >> > > + * Compute the temperature using the integer and decimal part
> >> and
> >> > >> return
> >> > >> > > + * millidegrees. The decimal part are only the top 3 bits so we
> >> > >> shift it
> >> > >> > > by
> >> > >> > > + * 5 here.
> >> > >> > > + */
> >> > >> > > +static uint32_t regs_to_temp(uint8_t integer, uint8_t decimal)
> >> > >> > > +{
> >> > >> > > + return ((integer << 3) + (decimal >> 5)) *
> >> > >> TEMP_UNIT_IN_MILLIDEGREE;
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +/*
> >> > >> > > + * Compute the integer and decimal parts of the temperature in
> >> > >> > > millidegrees.
> >> > >> > > + * H/W store the decimal in the top 3 bits so we shift it by 5.
> >> > >> > > + */
> >> > >> > > +static void temp_to_regs(uint32_t temp, uint8_t *integer,
> >> uint8_t
> >> > >> > > *decimal)
> >> > >> > > +{
> >> > >> > > + temp /= TEMP_UNIT_IN_MILLIDEGREE;
> >> > >> > > + *integer = temp >> 3;
> >> > >> > > + *decimal = (temp & 0x7) << 5;
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static void tx_rx(void *obj, void *data, QGuestAllocator *alloc)
> >> > >> > > +{
> >> > >> > > + uint16_t value;
> >> > >> > > + uint8_t integer, decimal;
> >> > >> > > + QI2CDevice *i2cdev = (QI2CDevice *)obj;
> >> > >> > > +
> >> > >> > > + /* Test default values */
> >> > >> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
> >> > >> > > + g_assert_cmpuint(value, ==, 0);
> >> > >> > > +
> >> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> >> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> >> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 0);
> >> > >> > > +
> >> > >> > > + /* Test setting temperature */
> >> > >> > > + qmp_sbtsi_set_temperature(TEST_ID, 20000);
> >> > >> > > + value = qmp_sbtsi_get_temperature(TEST_ID);
> >> > >> > > + g_assert_cmpuint(value, ==, 20000);
> >> > >> > > +
> >> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_INT);
> >> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
> >> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 20000);
> >> > >> > > +
> >> > >> > > + /* Set alert mask in config */
> >> > >> > > + i2c_set8(i2cdev, REG_CONFIG_WR, CONFIG_ALERT_MASK);
> >> > >> > > + value = i2c_get8(i2cdev, REG_CONFIG);
> >> > >> > > + g_assert_cmphex(value, ==, CONFIG_ALERT_MASK);
> >> > >> > > + /* Enable alarm_en */
> >> > >> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, ALARM_EN);
> >> > >> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> >> > >> > > + g_assert_cmphex(value, ==, ALARM_EN);
> >> > >> > > +
> >> > >> > > + /* Test setting limits */
> >> > >> > > + /* Limit low = 10.500 */
> >> > >> > > + temp_to_regs(LIMIT_LOW, &integer, &decimal);
> >> > >> > > + i2c_set8(i2cdev, REG_TEMP_LOW_INT, integer);
> >> > >> > > + i2c_set8(i2cdev, REG_TEMP_LOW_DEC, decimal);
> >> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_LOW_INT);
> >> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_LOW_DEC);
> >> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==,
> >> LIMIT_LOW);
> >> > >> > > + /* Limit high = 55.125 */
> >> > >> > > + temp_to_regs(LIMIT_HIGH, &integer, &decimal);
> >> > >> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_INT, integer);
> >> > >> > > + i2c_set8(i2cdev, REG_TEMP_HIGH_DEC, decimal);
> >> > >> > > + integer = i2c_get8(i2cdev, REG_TEMP_HIGH_INT);
> >> > >> > > + decimal = i2c_get8(i2cdev, REG_TEMP_HIGH_DEC);
> >> > >> > > + g_assert_cmpuint(regs_to_temp(integer, decimal), ==,
> >> LIMIT_HIGH);
> >> > >> > > + /* No alert is generated. */
> >> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> >> > >> > > + g_assert_cmphex(value, ==, 0);
> >> > >> > > +
> >> > >> > > + /* Test alert for low temperature */
> >> > >> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_LOW);
> >> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> >> > >> > > + g_assert_cmphex(value, ==, STATUS_LOW_ALERT);
> >> > >> > > +
> >> > >> > > + /* Test alert for high temperature */
> >> > >> > > + qmp_sbtsi_set_temperature(TEST_ID, LIMIT_HIGH);
> >> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> >> > >> > > + g_assert_cmphex(value, ==, STATUS_HIGH_ALERT);
> >> > >> > > +
> >> > >> > > + /* Disable alarm_en */
> >> > >> > > + i2c_set8(i2cdev, REG_ALERT_CONFIG, 0);
> >> > >> > > + value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
> >> > >> > > + g_assert_cmphex(value, ==, 0);
> >> > >> > > + /* No alert when alarm_en is false. */
> >> > >> > > + value = i2c_get8(i2cdev, REG_STATUS);
> >> > >> > > + g_assert_cmphex(value, ==, 0);
> >> > >> > > +}
> >> > >> > > +
> >> > >> > > +static void sbtsi_register_nodes(void)
> >> > >> > > +{
> >> > >> > > + QOSGraphEdgeOptions opts = {
> >> > >> > > + .extra_device_opts = "id=" TEST_ID ",address=0x4c"
> >> > >> > > + };
> >> > >> > > + add_qi2c_address(&opts, &(QI2CAddress) { TEST_ADDR });
> >> > >> > > +
> >> > >> > > + qos_node_create_driver("sbtsi", i2c_device_create);
> >> > >> > > + qos_node_consumes("sbtsi", "i2c-bus", &opts);
> >> > >> > > +
> >> > >> > > + qos_add_test("tx-rx", "sbtsi", tx_rx, NULL);
> >> > >> > > +}
> >> > >> > > +libqos_init(sbtsi_register_nodes);
> >> > >> > > --
> >> > >> >
> >> > >> >
> >> > >> > + Corey for i2c maintainer. The new sensor directory is mostly if
> >> not
> >> > >> > entirely i2c devices. I didn't create a maintainer entry for this
> >> i2c
> >> > >> > device, but I can if desired and send out a v2.
> >> > >>
> >> > >> Yeah, I guess I should be maintainer there. I'll queue up a change
> >> for
> >> > >> that. Thanks.
> >> > >>
> >> > >> -corey
> >> > >>
> >> > >> >
> >> > >> >
> >> > >> > > 2.34.1.575.g55b058a8bb-goog
> >> > >> > >
> >> > >> > >
> >> > >>
> >> > >
> >>
> >
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface
@ 2021-08-12 16:51 Hao Wu
0 siblings, 0 replies; 15+ messages in thread
From: Hao Wu @ 2021-08-12 16:51 UTC (permalink / raw)
To: minyard; +Cc: qemu-arm, qemu-devel, wuhaotsh, titusr, venture, Doug Evans
SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
interface that reports AMD SoC's Ttcl (normalized temperature),
and resembles a typical 8-pin remote temperature sensor's I2C interface
to BMC.
This patch implements a basic AMD SB-TSI sensor that is
compatible with the open-source data sheet from AMD and Linux
kernel driver.
Reference:
Linux kernel driver:
https://lkml.org/lkml/2020/12/11/968
Register Map:
https://developer.amd.com/wp-content/resources/56255_3_03.PDF
(Chapter 6)
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Doug Evans <dje@google.com>
---
hw/sensor/Kconfig | 4 +
hw/sensor/meson.build | 1 +
hw/sensor/tmp_sbtsi.c | 393 +++++++++++++++++++++++++++++++++++
hw/sensor/trace-events | 5 +
hw/sensor/trace.h | 1 +
meson.build | 1 +
tests/qtest/meson.build | 1 +
tests/qtest/tmp_sbtsi-test.c | 180 ++++++++++++++++
8 files changed, 586 insertions(+)
create mode 100644 hw/sensor/tmp_sbtsi.c
create mode 100644 hw/sensor/trace-events
create mode 100644 hw/sensor/trace.h
create mode 100644 tests/qtest/tmp_sbtsi-test.c
diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
index a2b55a4fdb..31e78e6fd5 100644
--- a/hw/sensor/Kconfig
+++ b/hw/sensor/Kconfig
@@ -17,3 +17,7 @@ config ADM1272
config MAX34451
bool
depends on I2C
+
+config AMDSBTSI
+ bool
+ depends on I2C
diff --git a/hw/sensor/meson.build b/hw/sensor/meson.build
index 034e3e0207..4e6747b2f2 100644
--- a/hw/sensor/meson.build
+++ b/hw/sensor/meson.build
@@ -3,3 +3,4 @@ softmmu_ss.add(when: 'CONFIG_TMP421', if_true: files('tmp421.c'))
softmmu_ss.add(when: 'CONFIG_EMC141X', if_true: files('emc141x.c'))
softmmu_ss.add(when: 'CONFIG_ADM1272', if_true: files('adm1272.c'))
softmmu_ss.add(when: 'CONFIG_MAX34451', if_true: files('max34451.c'))
+softmmu_ss.add(when: 'CONFIG_AMDSBTSI', if_true: files('tmp_sbtsi.c'))
diff --git a/hw/sensor/tmp_sbtsi.c b/hw/sensor/tmp_sbtsi.c
new file mode 100644
index 0000000000..b68c7ebf61
--- /dev/null
+++ b/hw/sensor/tmp_sbtsi.c
@@ -0,0 +1,393 @@
+/*
+ * AMD SBI Temperature Sensor Interface (SB-TSI)
+ *
+ * Copyright 2021 Google LLC
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ */
+
+#include "qemu/osdep.h"
+#include "hw/i2c/smbus_slave.h"
+#include "hw/irq.h"
+#include "migration/vmstate.h"
+#include "qapi/error.h"
+#include "qapi/visitor.h"
+#include "qemu/log.h"
+#include "qemu/module.h"
+#include "trace.h"
+
+#define TYPE_SBTSI "sbtsi"
+#define SBTSI(obj) OBJECT_CHECK(SBTSIState, (obj), TYPE_SBTSI)
+
+/**
+ * SBTSIState:
+ * temperatures are in units of 0.125 degrees
+ * @temperature: Temperature
+ * @limit_low: Lowest temperature
+ * @limit_high: Highest temperature
+ * @status: The status register
+ * @config: The config register
+ * @alert_config: The config for alarm_l output.
+ * @addr: The address to read/write for the next cmd.
+ * @alarm: The alarm_l output pin (GPIO)
+ */
+typedef struct SBTSIState {
+ SMBusDevice parent;
+
+ uint32_t temperature;
+ uint32_t limit_low;
+ uint32_t limit_high;
+ uint8_t status;
+ uint8_t config;
+ uint8_t alert_config;
+ uint8_t addr;
+ qemu_irq alarm;
+} SBTSIState;
+
+/*
+ * SB-TSI registers only support SMBus byte data access. "_INT" registers are
+ * the integer part of a temperature value or limit, and "_DEC" registers are
+ * corresponding decimal parts.
+ */
+#define SBTSI_REG_TEMP_INT 0x01 /* RO */
+#define SBTSI_REG_STATUS 0x02 /* RO */
+#define SBTSI_REG_CONFIG 0x03 /* RO */
+#define SBTSI_REG_TEMP_HIGH_INT 0x07 /* RW */
+#define SBTSI_REG_TEMP_LOW_INT 0x08 /* RW */
+#define SBTSI_REG_CONFIG_WR 0x09 /* RW */
+#define SBTSI_REG_TEMP_DEC 0x10 /* RO */
+#define SBTSI_REG_TEMP_HIGH_DEC 0x13 /* RW */
+#define SBTSI_REG_TEMP_LOW_DEC 0x14 /* RW */
+#define SBTSI_REG_ALERT_CONFIG 0xBF /* RW */
+#define SBTSI_REG_MAN 0xFE /* RO */
+#define SBTSI_REG_REV 0xFF /* RO */
+
+#define SBTSI_STATUS_HIGH_ALERT BIT(4)
+#define SBTSI_STATUS_LOW_ALERT BIT(3)
+#define SBTSI_CONFIG_ALERT_MASK BIT(7)
+#define SBTSI_ALARM_EN BIT(0)
+
+#define SBTSI_LIMIT_LOW_DEFAULT (0)
+#define SBTSI_LIMIT_HIGH_DEFAULT (560)
+#define SBTSI_MAN_DEFAULT (0)
+#define SBTSI_REV_DEFAULT (4)
+#define SBTSI_ALARM_L "alarm_l"
+
+/* The temperature we stored are in units of 0.125 degrees. */
+#define SBTSI_TEMP_UNIT_IN_MILLIDEGREE 125
+
+/*
+ * The integer part and decimal of the temperature both 8 bits.
+ * Only the top 3 bits of the decimal parts are used.
+ * So the max temperature is (2^8-1) + (2^3-1)/8 = 255.875 degrees.
+ */
+#define SBTSI_TEMP_MAX 255875
+
+/* The integer part of the temperature in terms of 0.125 degrees. */
+static uint8_t get_temp_int(uint32_t temp)
+{
+ return temp >> 3;
+}
+
+/*
+ * The decimal part of the temperature, in terms of 0.125 degrees.
+ * H/W store it in the top 3 bits so we shift it by 5.
+ */
+static uint8_t get_temp_dec(uint32_t temp)
+{
+ return (temp & 0x7) << 5;
+}
+
+/*
+ * Compute the temperature using the integer and decimal part,
+ * in terms of 0.125 degrees. The decimal part are only the top 3 bits
+ * so we shift it by 5 here.
+ */
+static uint32_t compute_temp(uint8_t integer, uint8_t decimal)
+{
+ return (integer << 3) + (decimal >> 5);
+}
+
+/* Compute new temp with new int part of the temperature. */
+static uint32_t compute_temp_int(uint32_t temp, uint8_t integer)
+{
+ return compute_temp(integer, get_temp_dec(temp));
+}
+
+/* Compute new temp with new dec part of the temperature. */
+static uint32_t compute_temp_dec(uint32_t temp, uint8_t decimal)
+{
+ return compute_temp(get_temp_int(temp), decimal);
+}
+
+/* The integer part of the temperature. */
+static void sbtsi_update_status(SBTSIState *s)
+{
+ s->status = 0;
+ if (s->alert_config & SBTSI_ALARM_EN) {
+ if (s->temperature >= s->limit_high) {
+ s->status |= SBTSI_STATUS_HIGH_ALERT;
+ }
+ if (s->temperature <= s->limit_low) {
+ s->status |= SBTSI_STATUS_LOW_ALERT;
+ }
+ }
+}
+
+static void sbtsi_update_alarm(SBTSIState *s)
+{
+ sbtsi_update_status(s);
+ if (s->status != 0 && !(s->config & SBTSI_CONFIG_ALERT_MASK)) {
+ qemu_irq_raise(s->alarm);
+ } else {
+ qemu_irq_lower(s->alarm);
+ }
+}
+
+static uint8_t sbtsi_read_byte(SMBusDevice *d)
+{
+ SBTSIState *s = SBTSI(d);
+ uint8_t data = 0;
+
+ switch (s->addr) {
+ case SBTSI_REG_TEMP_INT:
+ data = get_temp_int(s->temperature);
+ break;
+
+ case SBTSI_REG_TEMP_DEC:
+ data = get_temp_dec(s->temperature);
+ break;
+
+ case SBTSI_REG_TEMP_HIGH_INT:
+ data = get_temp_int(s->limit_high);
+ break;
+
+ case SBTSI_REG_TEMP_LOW_INT:
+ data = get_temp_int(s->limit_low);
+ break;
+
+ case SBTSI_REG_TEMP_HIGH_DEC:
+ data = get_temp_dec(s->limit_high);
+ break;
+
+ case SBTSI_REG_TEMP_LOW_DEC:
+ data = get_temp_dec(s->limit_low);
+ break;
+
+ case SBTSI_REG_CONFIG:
+ case SBTSI_REG_CONFIG_WR:
+ data = s->config;
+ break;
+
+ case SBTSI_REG_STATUS:
+ sbtsi_update_alarm(s);
+ data = s->status;
+ break;
+
+ case SBTSI_REG_ALERT_CONFIG:
+ data = s->alert_config;
+ break;
+
+ case SBTSI_REG_MAN:
+ data = SBTSI_MAN_DEFAULT;
+ break;
+
+ case SBTSI_REG_REV:
+ data = SBTSI_REV_DEFAULT;
+ break;
+
+ default:
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: reading from invalid reg: 0x%02x\n",
+ __func__, s->addr);
+ break;
+ }
+
+ trace_tmp_sbtsi_read_data(s->addr, data);
+ return data;
+}
+
+static void sbtsi_write(SBTSIState *s, uint8_t data)
+{
+ trace_tmp_sbtsi_write_data(s->addr, data);
+ switch (s->addr) {
+ case SBTSI_REG_CONFIG_WR:
+ s->config = data;
+ break;
+
+ case SBTSI_REG_TEMP_HIGH_INT:
+ s->limit_high = compute_temp_int(s->limit_high, data);
+ break;
+
+ case SBTSI_REG_TEMP_LOW_INT:
+ s->limit_low = compute_temp_int(s->limit_low, data);
+ break;
+
+ case SBTSI_REG_TEMP_HIGH_DEC:
+ s->limit_high = compute_temp_dec(s->limit_high, data);
+ break;
+
+ case SBTSI_REG_TEMP_LOW_DEC:
+ s->limit_low = compute_temp_dec(s->limit_low, data);
+ break;
+
+ case SBTSI_REG_ALERT_CONFIG:
+ s->alert_config = data;
+ break;
+
+ case SBTSI_REG_TEMP_INT:
+ case SBTSI_REG_TEMP_DEC:
+ case SBTSI_REG_CONFIG:
+ case SBTSI_REG_STATUS:
+ case SBTSI_REG_MAN:
+ case SBTSI_REG_REV:
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: writing to read only reg: 0x%02x data: 0x%02x\n",
+ __func__, s->addr, data);
+ break;
+
+ default:
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: writing to invalid reg: 0x%02x data: 0x%02x\n",
+ __func__, s->addr, data);
+ break;
+ }
+ sbtsi_update_alarm(s);
+}
+
+static int sbtsi_write_data(SMBusDevice *d, uint8_t *buf, uint8_t len)
+{
+ SBTSIState *s = SBTSI(d);
+
+ if (len == 0) {
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: writing empty data\n", __func__);
+ return -1;
+ }
+
+ s->addr = buf[0];
+ if (len > 1) {
+ sbtsi_write(s, buf[1]);
+ if (len > 2) {
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: extra data at end\n", __func__);
+ }
+ }
+ return 0;
+}
+
+/* Units are millidegrees. */
+static void sbtsi_get_temperature(Object *obj, Visitor *v, const char *name,
+ void *opaque, Error **errp)
+{
+ SBTSIState *s = SBTSI(obj);
+ uint32_t temp = s->temperature * SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
+
+ visit_type_uint32(v, name, &temp, errp);
+}
+
+/* Units are millidegrees. */
+static void sbtsi_set_temperature(Object *obj, Visitor *v, const char *name,
+ void *opaque, Error **errp)
+{
+ SBTSIState *s = SBTSI(obj);
+ uint32_t temp;
+
+ if (!visit_type_uint32(v, name, &temp, errp)) {
+ return;
+ }
+ if (temp > SBTSI_TEMP_MAX) {
+ error_setg(errp, "value %" PRIu32 ".%03" PRIu32 " C is out of range",
+ temp / 1000, temp % 1000);
+ return;
+ }
+
+ s->temperature = temp / SBTSI_TEMP_UNIT_IN_MILLIDEGREE;
+ sbtsi_update_alarm(s);
+}
+
+static int sbtsi_post_load(void *opaque, int version_id)
+{
+ SBTSIState *s = opaque;
+
+ sbtsi_update_alarm(s);
+ return 0;
+}
+
+static const VMStateDescription vmstate_sbtsi = {
+ .name = "SBTSI",
+ .version_id = 0,
+ .minimum_version_id = 0,
+ .post_load = sbtsi_post_load,
+ .fields = (VMStateField[]) {
+ VMSTATE_UINT32(temperature, SBTSIState),
+ VMSTATE_UINT32(limit_low, SBTSIState),
+ VMSTATE_UINT32(limit_high, SBTSIState),
+ VMSTATE_UINT8(config, SBTSIState),
+ VMSTATE_UINT8(status, SBTSIState),
+ VMSTATE_UINT8(addr, SBTSIState),
+ VMSTATE_END_OF_LIST()
+ }
+};
+
+static void sbtsi_enter_reset(Object *obj, ResetType type)
+{
+ SBTSIState *s = SBTSI(obj);
+
+ s->config = 0;
+ s->limit_low = SBTSI_LIMIT_LOW_DEFAULT;
+ s->limit_high = SBTSI_LIMIT_HIGH_DEFAULT;
+}
+
+static void sbtsi_hold_reset(Object *obj)
+{
+ SBTSIState *s = SBTSI(obj);
+
+ qemu_irq_lower(s->alarm);
+}
+
+static void sbtsi_init(Object *obj)
+{
+ SBTSIState *s = SBTSI(obj);
+
+ /* Current temperature in millidegrees. */
+ object_property_add(obj, "temperature", "uint32",
+ sbtsi_get_temperature, sbtsi_set_temperature,
+ NULL, NULL);
+ qdev_init_gpio_out_named(DEVICE(obj), &s->alarm, SBTSI_ALARM_L, 0);
+}
+
+static void sbtsi_class_init(ObjectClass *klass, void *data)
+{
+ ResettableClass *rc = RESETTABLE_CLASS(klass);
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ SMBusDeviceClass *k = SMBUS_DEVICE_CLASS(klass);
+
+ dc->desc = "SB-TSI Temperature Sensor";
+ dc->vmsd = &vmstate_sbtsi;
+ k->write_data = sbtsi_write_data;
+ k->receive_byte = sbtsi_read_byte;
+ rc->phases.enter = sbtsi_enter_reset;
+ rc->phases.hold = sbtsi_hold_reset;
+}
+
+static const TypeInfo sbtsi_info = {
+ .name = TYPE_SBTSI,
+ .parent = TYPE_SMBUS_DEVICE,
+ .instance_size = sizeof(SBTSIState),
+ .instance_init = sbtsi_init,
+ .class_init = sbtsi_class_init,
+};
+
+static void sbtsi_register_types(void)
+{
+ type_register_static(&sbtsi_info);
+}
+
+type_init(sbtsi_register_types)
diff --git a/hw/sensor/trace-events b/hw/sensor/trace-events
new file mode 100644
index 0000000000..21ab3809e2
--- /dev/null
+++ b/hw/sensor/trace-events
@@ -0,0 +1,5 @@
+# See docs/devel/tracing.rst for syntax documentation.
+
+# tmp_sbtsi.c
+tmp_sbtsi_write_data(uint8_t addr, uint8_t value) "SBTSI write addr:0x%02x data: 0x%02x"
+tmp_sbtsi_read_data(uint8_t addr, uint8_t value) "SBTSI read addr:0x%02x data: 0x%02x"
diff --git a/hw/sensor/trace.h b/hw/sensor/trace.h
new file mode 100644
index 0000000000..e4721560b0
--- /dev/null
+++ b/hw/sensor/trace.h
@@ -0,0 +1 @@
+#include "trace/trace-hw_sensor.h"
diff --git a/meson.build b/meson.build
index b3e7ec0e92..e62db1163a 100644
--- a/meson.build
+++ b/meson.build
@@ -2138,6 +2138,7 @@ if have_system
'hw/rtc',
'hw/s390x',
'hw/scsi',
+ 'hw/sensor',
'hw/sd',
'hw/sparc',
'hw/sparc64',
diff --git a/tests/qtest/meson.build b/tests/qtest/meson.build
index e22a0792c5..72671e316a 100644
--- a/tests/qtest/meson.build
+++ b/tests/qtest/meson.build
@@ -222,6 +222,7 @@ qos_test_ss.add(
'spapr-phb-test.c',
'tmp105-test.c',
'emc141x-test.c',
+ 'tmp_sbtsi-test.c',
'usb-hcd-ohci-test.c',
'virtio-test.c',
'virtio-blk-test.c',
diff --git a/tests/qtest/tmp_sbtsi-test.c b/tests/qtest/tmp_sbtsi-test.c
new file mode 100644
index 0000000000..7f5fafacc7
--- /dev/null
+++ b/tests/qtest/tmp_sbtsi-test.c
@@ -0,0 +1,180 @@
+/*
+ * QTests for the SBTSI temperature sensor
+ *
+ * Copyright 2020 Google LLC
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ */
+
+#include "qemu/osdep.h"
+
+#include "libqtest-single.h"
+#include "libqos/qgraph.h"
+#include "libqos/i2c.h"
+#include "qapi/qmp/qdict.h"
+#include "qemu/bitops.h"
+
+#define TEST_ID "sbtsi-test"
+#define TEST_ADDR (0x4c)
+
+/*
+ * SB-TSI registers only support SMBus byte data access. "_INT" registers are
+ * the integer part of a temperature value or limit, and "_DEC" registers are
+ * corresponding decimal parts.
+ */
+#define REG_TEMP_INT 0x01 /* RO */
+#define REG_STATUS 0x02 /* RO */
+#define REG_CONFIG 0x03 /* RO */
+#define REG_TEMP_HIGH_INT 0x07 /* RW */
+#define REG_TEMP_LOW_INT 0x08 /* RW */
+#define REG_CONFIG_WR 0x09 /* RW */
+#define REG_TEMP_DEC 0x10 /* RO */
+#define REG_TEMP_HIGH_DEC 0x13 /* RW */
+#define REG_TEMP_LOW_DEC 0x14 /* RW */
+#define REG_ALERT_CONFIG 0xBF /* RW */
+
+#define STATUS_HIGH_ALERT BIT(4)
+#define STATUS_LOW_ALERT BIT(3)
+#define CONFIG_ALERT_MASK BIT(7)
+#define ALARM_EN BIT(0)
+
+/* The temperature stored are in units of 0.125 degrees. */
+#define TEMP_UNIT_IN_MILLIDEGREE 125
+#define LIMIT_LOW (10500)
+#define LIMIT_HIGH (55125)
+
+static uint32_t qmp_sbtsi_get_temperature(const char *id)
+{
+ QDict *response;
+ int ret;
+
+ response = qmp("{ 'execute': 'qom-get', 'arguments': { 'path': %s, "
+ "'property': 'temperature' } }", id);
+ g_assert(qdict_haskey(response, "return"));
+ ret = (uint32_t)qdict_get_int(response, "return");
+ qobject_unref(response);
+ return ret;
+}
+
+static void qmp_sbtsi_set_temperature(const char *id, uint32_t value)
+{
+ QDict *response;
+
+ response = qmp("{ 'execute': 'qom-set', 'arguments': { 'path': %s, "
+ "'property': 'temperature', 'value': %d } }", id, value);
+ g_assert(qdict_haskey(response, "return"));
+ qobject_unref(response);
+}
+
+/*
+ * Compute the temperature using the integer and decimal part and return
+ * millidegrees. The decimal part are only the top 3 bits so we shift it by
+ * 5 here.
+ */
+static uint32_t regs_to_temp(uint8_t integer, uint8_t decimal)
+{
+ return ((integer << 3) + (decimal >> 5)) * TEMP_UNIT_IN_MILLIDEGREE;
+}
+
+/*
+ * Compute the integer and decimal parts of the temperature in millidegrees.
+ * H/W store the decimal in the top 3 bits so we shift it by 5.
+ */
+static void temp_to_regs(uint32_t temp, uint8_t *integer, uint8_t *decimal)
+{
+ temp /= TEMP_UNIT_IN_MILLIDEGREE;
+ *integer = temp >> 3;
+ *decimal = (temp & 0x7) << 5;
+}
+
+static void tx_rx(void *obj, void *data, QGuestAllocator *alloc)
+{
+ uint16_t value;
+ uint8_t integer, decimal;
+ QI2CDevice *i2cdev = (QI2CDevice *)obj;
+
+ /* Test default values */
+ value = qmp_sbtsi_get_temperature(TEST_ID);
+ g_assert_cmpuint(value, ==, 0);
+
+ integer = i2c_get8(i2cdev, REG_TEMP_INT);
+ decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
+ g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 0);
+
+ /* Test setting temperature */
+ qmp_sbtsi_set_temperature(TEST_ID, 20000);
+ value = qmp_sbtsi_get_temperature(TEST_ID);
+ g_assert_cmpuint(value, ==, 20000);
+
+ integer = i2c_get8(i2cdev, REG_TEMP_INT);
+ decimal = i2c_get8(i2cdev, REG_TEMP_DEC);
+ g_assert_cmpuint(regs_to_temp(integer, decimal), ==, 20000);
+
+ /* Set alert mask in config */
+ i2c_set8(i2cdev, REG_CONFIG_WR, CONFIG_ALERT_MASK);
+ value = i2c_get8(i2cdev, REG_CONFIG);
+ g_assert_cmphex(value, ==, CONFIG_ALERT_MASK);
+ /* Enable alarm_en */
+ i2c_set8(i2cdev, REG_ALERT_CONFIG, ALARM_EN);
+ value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
+ g_assert_cmphex(value, ==, ALARM_EN);
+
+ /* Test setting limits */
+ /* Limit low = 10.500 */
+ temp_to_regs(LIMIT_LOW, &integer, &decimal);
+ i2c_set8(i2cdev, REG_TEMP_LOW_INT, integer);
+ i2c_set8(i2cdev, REG_TEMP_LOW_DEC, decimal);
+ integer = i2c_get8(i2cdev, REG_TEMP_LOW_INT);
+ decimal = i2c_get8(i2cdev, REG_TEMP_LOW_DEC);
+ g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_LOW);
+ /* Limit high = 55.125 */
+ temp_to_regs(LIMIT_HIGH, &integer, &decimal);
+ i2c_set8(i2cdev, REG_TEMP_HIGH_INT, integer);
+ i2c_set8(i2cdev, REG_TEMP_HIGH_DEC, decimal);
+ integer = i2c_get8(i2cdev, REG_TEMP_HIGH_INT);
+ decimal = i2c_get8(i2cdev, REG_TEMP_HIGH_DEC);
+ g_assert_cmpuint(regs_to_temp(integer, decimal), ==, LIMIT_HIGH);
+ /* No alert is generated. */
+ value = i2c_get8(i2cdev, REG_STATUS);
+ g_assert_cmphex(value, ==, 0);
+
+ /* Test alert for low temperature */
+ qmp_sbtsi_set_temperature(TEST_ID, LIMIT_LOW);
+ value = i2c_get8(i2cdev, REG_STATUS);
+ g_assert_cmphex(value, ==, STATUS_LOW_ALERT);
+
+ /* Test alert for high temperature */
+ qmp_sbtsi_set_temperature(TEST_ID, LIMIT_HIGH);
+ value = i2c_get8(i2cdev, REG_STATUS);
+ g_assert_cmphex(value, ==, STATUS_HIGH_ALERT);
+
+ /* Disable alarm_en */
+ i2c_set8(i2cdev, REG_ALERT_CONFIG, 0);
+ value = i2c_get8(i2cdev, REG_ALERT_CONFIG);
+ g_assert_cmphex(value, ==, 0);
+ /* No alert when alarm_en is false. */
+ value = i2c_get8(i2cdev, REG_STATUS);
+ g_assert_cmphex(value, ==, 0);
+}
+
+static void sbtsi_register_nodes(void)
+{
+ QOSGraphEdgeOptions opts = {
+ .extra_device_opts = "id=" TEST_ID ",address=0x4c"
+ };
+ add_qi2c_address(&opts, &(QI2CAddress) { TEST_ADDR });
+
+ qos_node_create_driver("sbtsi", i2c_device_create);
+ qos_node_consumes("sbtsi", "i2c-bus", &opts);
+
+ qos_add_test("tx-rx", "sbtsi", tx_rx, NULL);
+}
+libqos_init(sbtsi_register_nodes);
--
2.33.0.rc1.237.g0d66db33f3-goog
^ permalink raw reply related [flat|nested] 15+ messages in thread
end of thread, other threads:[~2022-01-28 2:01 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-01-08 3:04 [PATCH] hw/sensor: Add SB-TSI Temperature Sensor Interface Patrick Venture
2022-01-10 2:17 ` Patrick Venture
2022-01-17 14:05 ` Corey Minyard
2022-01-18 17:10 ` Patrick Venture
2022-01-27 0:09 ` Hao Wu
2022-01-27 14:55 ` Corey Minyard
2022-01-27 18:19 ` Hao Wu
2022-01-27 23:18 ` Patrick Venture
2022-01-28 1:58 ` Corey Minyard
2022-01-10 9:35 ` Philippe Mathieu-Daudé
2022-01-10 17:14 ` Patrick Venture
2022-01-10 19:30 ` Philippe Mathieu-Daudé
2022-01-10 19:41 ` Patrick Venture
2022-01-13 7:19 ` Thomas Huth
-- strict thread matches above, loose matches on Subject: below --
2021-08-12 16:51 Hao Wu
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.