* [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards
@ 2014-02-27 18:47 Anthony Felice
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 1/4] u-boot-timesys: Add version 2011.12 Anthony Felice
` (5 more replies)
0 siblings, 6 replies; 17+ messages in thread
From: Anthony Felice @ 2014-02-27 18:47 UTC (permalink / raw)
To: meta-freescale
This series adds support for the Phytec Cosmic Vybrid (pcl052) and Phytec phyCORE Vybrid (pcm052) machines.
The first patch adds a modified u-boot 2011.12 with board support enabled for these two machines, as the pcl052 and pcm052 are not supported in mainline u-boot.
The second patch reworks the linux-timesys recipe to use the twr-vf65gs10 machine name for sources. This is in preparation for the Phytec board support addition, as the Phytec machine names will also be used for sources.
The third patch adds the machine definition for the pcl052 board.
The fourth patch adds the machine definition for the pcm052 board.
^ permalink raw reply [flat|nested] 17+ messages in thread
* [meta-fsl-arm][PATCH 1/4] u-boot-timesys: Add version 2011.12
2014-02-27 18:47 [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards Anthony Felice
@ 2014-02-27 18:47 ` Anthony Felice
2014-02-27 19:37 ` Daiane.Angolini
2014-02-27 20:34 ` Otavio Salvador
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 2/4] linux-timesys: Use twr-vf65gs10 machine name for sources Anthony Felice
` (4 subsequent siblings)
5 siblings, 2 replies; 17+ messages in thread
From: Anthony Felice @ 2014-02-27 18:47 UTC (permalink / raw)
To: meta-freescale
Add some commits over u-boot 2011.12 with board support for the pcl052 and
pcm052 platforms, that include:
* Add NAND boot support
* Add FEC1 support
* Fix DDR3 settings for pcm052 1.1 silicon
* Fix SDHC issues
* New machine definitions (i.e. pcl052, pcm052)
and more, for a total of 25 commits. Included in these commits is also base
support for the Vybrid Tower platform.
Commits from the u-boot-cfi-flash fork from 2012-03-21 and earlier have also
been added, starting from commit 85c344e5f98: "cfi: fix the incomplete erased
status check in buffer write".
This version has been tested on the pcl052 and pcm052 platforms.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
---
recipes-bsp/u-boot/u-boot-timesys_2011.12.bb | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
create mode 100644 recipes-bsp/u-boot/u-boot-timesys_2011.12.bb
diff --git a/recipes-bsp/u-boot/u-boot-timesys_2011.12.bb b/recipes-bsp/u-boot/u-boot-timesys_2011.12.bb
new file mode 100644
index 0000000..4f103fd
--- /dev/null
+++ b/recipes-bsp/u-boot/u-boot-timesys_2011.12.bb
@@ -0,0 +1,18 @@
+DESCRIPTION = "bootloader for Vybrid platforms"
+require recipes-bsp/u-boot/u-boot.inc
+
+PROVIDES += "u-boot"
+
+LICENSE = "GPLv2+"
+LIC_FILES_CHKSUM = "file://COPYING;md5=1707d6db1d42237583f50183a5651ecb"
+
+SRCBRANCH = "2011.12-pcl052"
+SRC_URI = "git://github.com/Timesys/u-boot-timesys.git;protocol=git;branch=${SRCBRANCH}"
+SRCREV = "dca5026484c69628be9b9618e5795c635cefe110"
+
+S = "${WORKDIR}/git"
+
+PACKAGE_ARCH = "${MACHINE_ARCH}"
+COMPATIBLE_MACHINE = "(vf60)"
+
+PV = "v2011.12"
--
1.9.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [meta-fsl-arm][PATCH 2/4] linux-timesys: Use twr-vf65gs10 machine name for sources
2014-02-27 18:47 [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards Anthony Felice
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 1/4] u-boot-timesys: Add version 2011.12 Anthony Felice
@ 2014-02-27 18:47 ` Anthony Felice
2014-02-27 19:41 ` Daiane.Angolini
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 3/4] pcl052: Add machine definition Anthony Felice
` (3 subsequent siblings)
5 siblings, 1 reply; 17+ messages in thread
From: Anthony Felice @ 2014-02-27 18:47 UTC (permalink / raw)
To: meta-freescale
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
---
.../linux/linux-timesys-3.0.15/{ => twr-vf65gs10}/defconfig | 0
recipes-kernel/linux/linux-timesys_3.0.15.bb | 8 +++++---
2 files changed, 5 insertions(+), 3 deletions(-)
rename recipes-kernel/linux/linux-timesys-3.0.15/{ => twr-vf65gs10}/defconfig (100%)
diff --git a/recipes-kernel/linux/linux-timesys-3.0.15/defconfig b/recipes-kernel/linux/linux-timesys-3.0.15/twr-vf65gs10/defconfig
similarity index 100%
rename from recipes-kernel/linux/linux-timesys-3.0.15/defconfig
rename to recipes-kernel/linux/linux-timesys-3.0.15/twr-vf65gs10/defconfig
diff --git a/recipes-kernel/linux/linux-timesys_3.0.15.bb b/recipes-kernel/linux/linux-timesys_3.0.15.bb
index 217feb6..4c28f11 100644
--- a/recipes-kernel/linux/linux-timesys_3.0.15.bb
+++ b/recipes-kernel/linux/linux-timesys_3.0.15.bb
@@ -5,12 +5,14 @@ include linux-imx.inc
# Revision of 3.0.15_vybrid branch
SRC_URI = "git://github.com/Timesys/linux-timesys.git;protocol=git;branch=${SRCBRANCH} \
file://defconfig \
- file://0001-mvf_fec.c-Fix-mac-address-read-to-match-fuse-layout-.patch \
+"
+
+SRC_URI_append_twr-vf65gs10 = "file://0001-mvf_fec.c-Fix-mac-address-read-to-match-fuse-layout-.patch \
file://0002-mvf.c-Change-console-device-name-to-match-mainline-u.patch \
"
-SRCBRANCH = "3.0.15_vybrid-twr"
-SRCREV = "50c4c848d6b8743894cfcec166db475ef6140504"
+SRCBRANCH_twr-vf65gs10 = "3.0.15_vybrid-twr"
+SRCREV_twr-vf65gs10 = "50c4c848d6b8743894cfcec166db475ef6140504"
LOCALVERSION = "-3.0-mvf+yocto"
COMPATIBLE_MACHINE = "(vf60)"
--
1.9.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [meta-fsl-arm][PATCH 3/4] pcl052: Add machine definition
2014-02-27 18:47 [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards Anthony Felice
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 1/4] u-boot-timesys: Add version 2011.12 Anthony Felice
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 2/4] linux-timesys: Use twr-vf65gs10 machine name for sources Anthony Felice
@ 2014-02-27 18:47 ` Anthony Felice
2014-02-27 19:43 ` Daiane.Angolini
2014-02-27 20:37 ` Otavio Salvador
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 4/4] pcm052: " Anthony Felice
` (2 subsequent siblings)
5 siblings, 2 replies; 17+ messages in thread
From: Anthony Felice @ 2014-02-27 18:47 UTC (permalink / raw)
To: meta-freescale
Add machine definition for the Phytec Cosmic Vybrid board.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
---
conf/machine/pcl052.conf | 22 +++
.../linux/linux-timesys-3.0.15/pcl052/defconfig | 168 +++++++++++++++++++++
recipes-kernel/linux/linux-timesys_3.0.15.bb | 2 +
3 files changed, 192 insertions(+)
create mode 100644 conf/machine/pcl052.conf
create mode 100644 recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
diff --git a/conf/machine/pcl052.conf b/conf/machine/pcl052.conf
new file mode 100644
index 0000000..611e93d
--- /dev/null
+++ b/conf/machine/pcl052.conf
@@ -0,0 +1,22 @@
+#@TYPE: Machine
+#@NAME: Phytec Cosmic Vybrid Development Kit
+#@SOC: vf60
+#@DESCRIPTION: Machine configuration for Phytec Cosmic Vybrid Development Kit
+#@MAINTAINER: Anthony Felice <tony.felice@timesys.com>
+
+include conf/machine/include/imx-base.inc
+include conf/machine/include/tune-cortexa5.inc
+
+SOC_FAMILY = "vf60"
+
+PREFERRED_PROVIDER_virtual/kernel = "linux-timesys"
+PREFERRED_PROVIDER_u-boot = "u-boot-timesys"
+
+UBOOT_MACHINE = "pcl052_config"
+
+SDCARD_ROOTFS ?= "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.ext3"
+IMAGE_FSTYPES ?= "tar.bz2 ext3 sdcard"
+
+SERIAL_CONSOLE = "115200 ttymxc1"
+
+MACHINE_FEATURES = "apm usbgadget usbhost vfat alsa"
diff --git a/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig b/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
new file mode 100644
index 0000000..3b6f1a6
--- /dev/null
+++ b/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
@@ -0,0 +1,168 @@
+CONFIG_EXPERIMENTAL=y
+CONFIG_LOCALVERSION="-3.0-mvf+yocto"
+CONFIG_SYSVIPC=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_EMBEDDED=y
+# CONFIG_PERF_EVENTS is not set
+CONFIG_PROFILING=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_MXC=y
+CONFIG_ARCH_MVF=y
+CONFIG_MACH_PCL052=y
+CONFIG_MXC_PWM=m
+CONFIG_MXC_USE_PIT=y
+CONFIG_DMA_ZONE_SIZE=16
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_ARM_ERRATA_743622=y
+CONFIG_ARM_ERRATA_754322=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_VMSPLIT_2G=y
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+CONFIG_COMPACTION=y
+CONFIG_KSM=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=/dev/nfs rw nfsroot=10.193.20.106:/tftpboot/10.193.20.115 ip=10.193.20.115:10.193.20.106:10.193.20.254:255.255.255.0::eth0:off console=ttymxc1,115200 mem=128M"
+CONFIG_VFP=y
+CONFIG_NEON=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_SUSPEND is not set
+CONFIG_PM_RUNTIME=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_INET_LRO is not set
+# CONFIG_IPV6 is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_FSL_NFC=y
+CONFIG_MTD_NAND_FSL_NFC_SWECC=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_MISC_DEVICES=y
+CONFIG_MVF_ADC=y
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_MICREL_PHY=y
+CONFIG_NET_ETHERNET=y
+CONFIG_FEC1=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_INPUT_POLLDEV=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=y
+# CONFIG_CONSOLE_TRANSLATIONS is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_IMX=y
+CONFIG_SERIAL_IMX_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_IMX=y
+CONFIG_SPI=y
+CONFIG_SPI_MVF_QSPI=m
+CONFIG_SPI_MVF=m
+CONFIG_SPI_SPIDEV=m
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_IMX2_WDT=y
+# CONFIG_MFD_MXC_HDMI is not set
+CONFIG_FB=y
+CONFIG_FB_MVF_DCU=y
+CONFIG_MVF_TDA_998X=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_SOUND=y
+# CONFIG_SOUND_OSS_CORE_PRECLAIM is not set
+CONFIG_SND=y
+CONFIG_SND_PCM_OSS=y
+CONFIG_SND_SOC=y
+# CONFIG_SND_SOC_PCM052_SGTL5000 is not set
+# CONFIG_HID_SUPPORT is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ARC=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ETH=m
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_ESDHC_IMX=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_SNVS=y
+CONFIG_DMADEVICES=y
+# CONFIG_MXC_HMP4E is not set
+# CONFIG_MXC_HWEVENT is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+CONFIG_EXT4_FS=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_CRAMFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_ROOT_NFS=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_EFI_PARTITION=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=m
+CONFIG_FTRACE=y
+CONFIG_ENABLE_DEFAULT_TRACERS=y
+CONFIG_CRYPTO_TEST=m
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_MICHAEL_MIC=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRC_CCITT=m
diff --git a/recipes-kernel/linux/linux-timesys_3.0.15.bb b/recipes-kernel/linux/linux-timesys_3.0.15.bb
index 4c28f11..bc8b077 100644
--- a/recipes-kernel/linux/linux-timesys_3.0.15.bb
+++ b/recipes-kernel/linux/linux-timesys_3.0.15.bb
@@ -13,6 +13,8 @@ SRC_URI_append_twr-vf65gs10 = "file://0001-mvf_fec.c-Fix-mac-address-read-to-mat
SRCBRANCH_twr-vf65gs10 = "3.0.15_vybrid-twr"
SRCREV_twr-vf65gs10 = "50c4c848d6b8743894cfcec166db475ef6140504"
+SRCBRANCH_pcl052 = "3.0-pcl052"
+SRCREV_pcl052 = "655f7949b5fd0b66bde03fc3c63c7a436353b1e1"
LOCALVERSION = "-3.0-mvf+yocto"
COMPATIBLE_MACHINE = "(vf60)"
--
1.9.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [meta-fsl-arm][PATCH 4/4] pcm052: Add machine definition
2014-02-27 18:47 [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards Anthony Felice
` (2 preceding siblings ...)
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 3/4] pcl052: Add machine definition Anthony Felice
@ 2014-02-27 18:47 ` Anthony Felice
2014-02-27 19:44 ` Daiane.Angolini
2014-02-27 20:39 ` Otavio Salvador
2014-02-27 19:47 ` [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards Daiane.Angolini
2014-02-27 20:41 ` Otavio Salvador
5 siblings, 2 replies; 17+ messages in thread
From: Anthony Felice @ 2014-02-27 18:47 UTC (permalink / raw)
To: meta-freescale
Add machine definition for the Phytec phyCORE Vybrid board.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
---
conf/machine/pcm052.conf | 22 +++
.../linux/linux-timesys-3.0.15/pcm052/defconfig | 163 +++++++++++++++++++++
recipes-kernel/linux/linux-timesys_3.0.15.bb | 2 +
3 files changed, 187 insertions(+)
create mode 100644 conf/machine/pcm052.conf
create mode 100644 recipes-kernel/linux/linux-timesys-3.0.15/pcm052/defconfig
diff --git a/conf/machine/pcm052.conf b/conf/machine/pcm052.conf
new file mode 100644
index 0000000..d86fdb0
--- /dev/null
+++ b/conf/machine/pcm052.conf
@@ -0,0 +1,22 @@
+#@TYPE: Machine
+#@NAME: Phytec phyCORE Vybrid Development Kit
+#@SOC: vf60
+#@DESCRIPTION: Machine configuration for Phytec phyCORE Vybrid Development Kit
+#@MAINTAINER: Anthony Felice <tony.felice@timesys.com>
+
+include conf/machine/include/imx-base.inc
+include conf/machine/include/tune-cortexa5.inc
+
+SOC_FAMILY = "vf60"
+
+PREFERRED_PROVIDER_virtual/kernel = "linux-timesys"
+PREFERRED_PROVIDER_u-boot = "u-boot-timesys"
+
+UBOOT_MACHINE = "pcm052_config"
+
+SDCARD_ROOTFS ?= "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.ext3"
+IMAGE_FSTYPES ?= "tar.bz2 ext3 sdcard"
+
+SERIAL_CONSOLE = "115200 ttymxc1"
+
+MACHINE_FEATURES = "apm usbgadget usbhost vfat alsa touchscreen"
diff --git a/recipes-kernel/linux/linux-timesys-3.0.15/pcm052/defconfig b/recipes-kernel/linux/linux-timesys-3.0.15/pcm052/defconfig
new file mode 100644
index 0000000..cb6419a
--- /dev/null
+++ b/recipes-kernel/linux/linux-timesys-3.0.15/pcm052/defconfig
@@ -0,0 +1,163 @@
+CONFIG_EXPERIMENTAL=y
+CONFIG_SYSVIPC=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_EMBEDDED=y
+# CONFIG_PERF_EVENTS is not set
+CONFIG_PROFILING=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_MXC=y
+CONFIG_ARCH_MVF=y
+CONFIG_MACH_PCM052=y
+CONFIG_MXC_PWM=y
+CONFIG_MXC_USE_PIT=y
+CONFIG_DMA_ZONE_SIZE=16
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_ARM_ERRATA_743622=y
+CONFIG_ARM_ERRATA_754322=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_VMSPLIT_2G=y
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+CONFIG_COMPACTION=y
+CONFIG_KSM=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=/dev/nfs rw nfsroot=10.193.20.106:/tftpboot/10.193.20.115 ip=10.193.20.115:10.193.20.106:10.193.20.254:255.255.255.0::eth0:off console=ttymxc1,115200 mem=128M"
+CONFIG_VFP=y
+CONFIG_NEON=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_SUSPEND is not set
+CONFIG_PM_RUNTIME=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_INET_LRO is not set
+# CONFIG_IPV6 is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_M25P80=y
+# CONFIG_M25PXX_USE_FAST_READ is not set
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_FSL_NFC=y
+CONFIG_MTD_NAND_FSL_NFC_SWECC=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_MISC_DEVICES=y
+CONFIG_MVF_ADC=y
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_MICREL_PHY=y
+CONFIG_NET_ETHERNET=y
+CONFIG_FEC1=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_INPUT_POLLDEV=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_STMPE=y
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=y
+# CONFIG_CONSOLE_TRANSLATIONS is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_IMX=y
+CONFIG_SERIAL_IMX_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_IMX=y
+CONFIG_SPI=y
+CONFIG_SPI_MVF_QSPI=y
+CONFIG_SPI_SPIDEV=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_IMX2_WDT=y
+CONFIG_MFD_STMPE=y
+# CONFIG_MFD_MXC_HDMI is not set
+CONFIG_FB=y
+CONFIG_FB_MVF_DCU=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_GENERIC=m
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_SOUND=y
+# CONFIG_SOUND_OSS_CORE_PRECLAIM is not set
+CONFIG_SND=y
+CONFIG_SND_PCM_OSS=y
+CONFIG_SND_SOC=y
+# CONFIG_HID_SUPPORT is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ARC=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ETH=m
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_ESDHC_IMX=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_SNVS=y
+CONFIG_DMADEVICES=y
+# CONFIG_MXC_HMP4E is not set
+# CONFIG_MXC_HWEVENT is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+CONFIG_EXT4_FS=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_CRAMFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_ROOT_NFS=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_EFI_PARTITION=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=m
+CONFIG_FTRACE=y
+CONFIG_ENABLE_DEFAULT_TRACERS=y
+CONFIG_CRYPTO_TEST=m
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_MICHAEL_MIC=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRC_CCITT=m
diff --git a/recipes-kernel/linux/linux-timesys_3.0.15.bb b/recipes-kernel/linux/linux-timesys_3.0.15.bb
index bc8b077..c0784c0 100644
--- a/recipes-kernel/linux/linux-timesys_3.0.15.bb
+++ b/recipes-kernel/linux/linux-timesys_3.0.15.bb
@@ -15,6 +15,8 @@ SRCBRANCH_twr-vf65gs10 = "3.0.15_vybrid-twr"
SRCREV_twr-vf65gs10 = "50c4c848d6b8743894cfcec166db475ef6140504"
SRCBRANCH_pcl052 = "3.0-pcl052"
SRCREV_pcl052 = "655f7949b5fd0b66bde03fc3c63c7a436353b1e1"
+SRCBRANCH_pcm052 = "3.0-pcm052"
+SRCREV_pcm052 = "7a27fd26d2b5b732e12ecea13a846679cbafe9a9"
LOCALVERSION = "-3.0-mvf+yocto"
COMPATIBLE_MACHINE = "(vf60)"
--
1.9.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 1/4] u-boot-timesys: Add version 2011.12
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 1/4] u-boot-timesys: Add version 2011.12 Anthony Felice
@ 2014-02-27 19:37 ` Daiane.Angolini
2014-02-27 20:34 ` Otavio Salvador
1 sibling, 0 replies; 17+ messages in thread
From: Daiane.Angolini @ 2014-02-27 19:37 UTC (permalink / raw)
To: Anthony Felice, meta-freescale
> -----Original Message-----
> From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
> bounces@yoctoproject.org] On Behalf Of Anthony Felice
> Sent: Thursday, February 27, 2014 3:48 PM
> To: meta-freescale@yoctoproject.org
> Subject: [meta-freescale] [meta-fsl-arm][PATCH 1/4] u-boot-timesys: Add
> version 2011.12
>
> Add some commits over u-boot 2011.12 with board support for the pcl052 and
> pcm052 platforms, that include:
>
> * Add NAND boot support
> * Add FEC1 support
> * Fix DDR3 settings for pcm052 1.1 silicon
> * Fix SDHC issues
> * New machine definitions (i.e. pcl052, pcm052)
>
> and more, for a total of 25 commits. Included in these commits is also base
> support for the Vybrid Tower platform.
>
> Commits from the u-boot-cfi-flash fork from 2012-03-21 and earlier have
> also been added, starting from commit 85c344e5f98: "cfi: fix the incomplete
> erased status check in buffer write".
>
> This version has been tested on the pcl052 and pcm052 platforms.
Great commit log!
>
> Signed-off-by: Anthony Felice <tony.felice@timesys.com>
> ---
> recipes-bsp/u-boot/u-boot-timesys_2011.12.bb | 18 ++++++++++++++++++
> 1 file changed, 18 insertions(+)
> create mode 100644 recipes-bsp/u-boot/u-boot-timesys_2011.12.bb
>
> diff --git a/recipes-bsp/u-boot/u-boot-timesys_2011.12.bb b/recipes-bsp/u-
> boot/u-boot-timesys_2011.12.bb
> new file mode 100644
> index 0000000..4f103fd
> --- /dev/null
> +++ b/recipes-bsp/u-boot/u-boot-timesys_2011.12.bb
> @@ -0,0 +1,18 @@
Shouldn´t have a Copyright line here?
> +DESCRIPTION = "bootloader for Vybrid platforms"
> +require recipes-bsp/u-boot/u-boot.inc
> +
> +PROVIDES += "u-boot"
> +
> +LICENSE = "GPLv2+"
> +LIC_FILES_CHKSUM = "file://COPYING;md5=1707d6db1d42237583f50183a5651ecb"
> +
> +SRCBRANCH = "2011.12-pcl052"
> +SRC_URI = "git://github.com/Timesys/u-boot-
> timesys.git;protocol=git;branch=${SRCBRANCH}"
> +SRCREV = "dca5026484c69628be9b9618e5795c635cefe110"
> +
> +S = "${WORKDIR}/git"
> +
> +PACKAGE_ARCH = "${MACHINE_ARCH}"
> +COMPATIBLE_MACHINE = "(vf60)"
> +
> +PV = "v2011.12"
Any plan to use u-boot mainline?
I found nothing else to comment on your patch.
reviewed-by,
daiane
> --
> 1.9.0
>
> _______________________________________________
> meta-freescale mailing list
> meta-freescale@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 2/4] linux-timesys: Use twr-vf65gs10 machine name for sources
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 2/4] linux-timesys: Use twr-vf65gs10 machine name for sources Anthony Felice
@ 2014-02-27 19:41 ` Daiane.Angolini
0 siblings, 0 replies; 17+ messages in thread
From: Daiane.Angolini @ 2014-02-27 19:41 UTC (permalink / raw)
To: Anthony Felice, meta-freescale
> -----Original Message-----
> From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
> bounces@yoctoproject.org] On Behalf Of Anthony Felice
> Sent: Thursday, February 27, 2014 3:48 PM
> To: meta-freescale@yoctoproject.org
> Subject: [meta-freescale] [meta-fsl-arm][PATCH 2/4] linux-timesys: Use twr-
> vf65gs10 machine name for sources
Guess what?
Please, add a commit log.
Say, for example, that you have dropped one patch and included a new one.
>
> Signed-off-by: Anthony Felice <tony.felice@timesys.com>
> ---
> .../linux/linux-timesys-3.0.15/{ => twr-vf65gs10}/defconfig | 0
> recipes-kernel/linux/linux-timesys_3.0.15.bb | 8
> +++++---
> 2 files changed, 5 insertions(+), 3 deletions(-) rename recipes-
> kernel/linux/linux-timesys-3.0.15/{ => twr-vf65gs10}/defconfig (100%)
>
> diff --git a/recipes-kernel/linux/linux-timesys-3.0.15/defconfig b/recipes-
> kernel/linux/linux-timesys-3.0.15/twr-vf65gs10/defconfig
> similarity index 100%
> rename from recipes-kernel/linux/linux-timesys-3.0.15/defconfig
> rename to recipes-kernel/linux/linux-timesys-3.0.15/twr-vf65gs10/defconfig
> diff --git a/recipes-kernel/linux/linux-timesys_3.0.15.bb b/recipes-
> kernel/linux/linux-timesys_3.0.15.bb
> index 217feb6..4c28f11 100644
> --- a/recipes-kernel/linux/linux-timesys_3.0.15.bb
> +++ b/recipes-kernel/linux/linux-timesys_3.0.15.bb
> @@ -5,12 +5,14 @@ include linux-imx.inc
> # Revision of 3.0.15_vybrid branch
> SRC_URI = "git://github.com/Timesys/linux-
> timesys.git;protocol=git;branch=${SRCBRANCH} \
> file://defconfig \
> - file://0001-mvf_fec.c-Fix-mac-address-read-to-match-fuse-
> layout-.patch \
> +"
> +
> +SRC_URI_append_twr-vf65gs10 =
> +"file://0001-mvf_fec.c-Fix-mac-address-read-to-match-fuse-layout-.patch
> +\
> file://0002-mvf.c-Change-console-device-name-to-match-mainline-
> u.patch \ "
>
> -SRCBRANCH = "3.0.15_vybrid-twr"
> -SRCREV = "50c4c848d6b8743894cfcec166db475ef6140504"
> +SRCBRANCH_twr-vf65gs10 = "3.0.15_vybrid-twr"
> +SRCREV_twr-vf65gs10 = "50c4c848d6b8743894cfcec166db475ef6140504"
> LOCALVERSION = "-3.0-mvf+yocto"
>
> COMPATIBLE_MACHINE = "(vf60)"
I´m not sure I understood here.
You set a SRCBRANCH for the board only (and you have dropped the generic SRCBRANCH),
however the compatible machine is for the board family.
Could you, please, double check?
Daiane
> --
> 1.9.0
>
> _______________________________________________
> meta-freescale mailing list
> meta-freescale@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 3/4] pcl052: Add machine definition
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 3/4] pcl052: Add machine definition Anthony Felice
@ 2014-02-27 19:43 ` Daiane.Angolini
2014-02-27 20:37 ` Otavio Salvador
1 sibling, 0 replies; 17+ messages in thread
From: Daiane.Angolini @ 2014-02-27 19:43 UTC (permalink / raw)
To: Anthony Felice, meta-freescale
> -----Original Message-----
> From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
> bounces@yoctoproject.org] On Behalf Of Anthony Felice
> Sent: Thursday, February 27, 2014 3:48 PM
> To: meta-freescale@yoctoproject.org
> Subject: [meta-freescale] [meta-fsl-arm][PATCH 3/4] pcl052: Add machine
> definition
>
> Add machine definition for the Phytec Cosmic Vybrid board.
>
Nothing to comment. I haven´t reviewed the defconfig.
Reviewed-by,
Daiane
> Signed-off-by: Anthony Felice <tony.felice@timesys.com>
> ---
> conf/machine/pcl052.conf | 22 +++
> .../linux/linux-timesys-3.0.15/pcl052/defconfig | 168
> +++++++++++++++++++++
> recipes-kernel/linux/linux-timesys_3.0.15.bb | 2 +
> 3 files changed, 192 insertions(+)
> create mode 100644 conf/machine/pcl052.conf create mode 100644 recipes-
> kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
>
> diff --git a/conf/machine/pcl052.conf b/conf/machine/pcl052.conf new file
> mode 100644 index 0000000..611e93d
> --- /dev/null
> +++ b/conf/machine/pcl052.conf
> @@ -0,0 +1,22 @@
> +#@TYPE: Machine
> +#@NAME: Phytec Cosmic Vybrid Development Kit
> +#@SOC: vf60
> +#@DESCRIPTION: Machine configuration for Phytec Cosmic Vybrid
> +Development Kit
> +#@MAINTAINER: Anthony Felice <tony.felice@timesys.com>
> +
> +include conf/machine/include/imx-base.inc include
> +conf/machine/include/tune-cortexa5.inc
> +
> +SOC_FAMILY = "vf60"
> +
> +PREFERRED_PROVIDER_virtual/kernel = "linux-timesys"
> +PREFERRED_PROVIDER_u-boot = "u-boot-timesys"
> +
> +UBOOT_MACHINE = "pcl052_config"
> +
> +SDCARD_ROOTFS ?= "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.ext3"
> +IMAGE_FSTYPES ?= "tar.bz2 ext3 sdcard"
> +
> +SERIAL_CONSOLE = "115200 ttymxc1"
> +
> +MACHINE_FEATURES = "apm usbgadget usbhost vfat alsa"
> diff --git a/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
> b/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
> new file mode 100644
> index 0000000..3b6f1a6
> --- /dev/null
> +++ b/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
> @@ -0,0 +1,168 @@
> +CONFIG_EXPERIMENTAL=y
> +CONFIG_LOCALVERSION="-3.0-mvf+yocto"
> +CONFIG_SYSVIPC=y
> +CONFIG_IKCONFIG=y
> +CONFIG_IKCONFIG_PROC=y
> +CONFIG_LOG_BUF_SHIFT=14
> +CONFIG_EMBEDDED=y
> +# CONFIG_PERF_EVENTS is not set
> +CONFIG_PROFILING=y
> +CONFIG_MODULES=y
> +CONFIG_MODULE_UNLOAD=y
> +CONFIG_MODULE_FORCE_UNLOAD=y
> +CONFIG_MODVERSIONS=y
> +# CONFIG_BLK_DEV_BSG is not set
> +CONFIG_ARCH_MXC=y
> +CONFIG_ARCH_MVF=y
> +CONFIG_MACH_PCL052=y
> +CONFIG_MXC_PWM=m
> +CONFIG_MXC_USE_PIT=y
> +CONFIG_DMA_ZONE_SIZE=16
> +# CONFIG_CACHE_L2X0 is not set
> +CONFIG_ARM_ERRATA_743622=y
> +CONFIG_ARM_ERRATA_754322=y
> +CONFIG_HIGH_RES_TIMERS=y
> +CONFIG_VMSPLIT_2G=y
> +CONFIG_AEABI=y
> +# CONFIG_OABI_COMPAT is not set
> +CONFIG_COMPACTION=y
> +CONFIG_KSM=y
> +CONFIG_ZBOOT_ROM_TEXT=0x0
> +CONFIG_ZBOOT_ROM_BSS=0x0
> +CONFIG_CMDLINE="root=/dev/nfs rw
> nfsroot=10.193.20.106:/tftpboot/10.193.20.115
> ip=10.193.20.115:10.193.20.106:10.193.20.254:255.255.255.0::eth0:off
> console=ttymxc1,115200 mem=128M"
> +CONFIG_VFP=y
> +CONFIG_NEON=y
> +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_SUSPEND is
> +not set CONFIG_PM_RUNTIME=y CONFIG_NET=y CONFIG_PACKET=y CONFIG_UNIX=y
> +CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_IP_PNP=y
> +CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_LRO is not set
> +# CONFIG_IPV6 is not set CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
> +CONFIG_DEVTMPFS=y
> +CONFIG_DEVTMPFS_MOUNT=y
> +CONFIG_MTD=y
> +CONFIG_MTD_CMDLINE_PARTS=y
> +CONFIG_MTD_CHAR=y
> +CONFIG_MTD_BLOCK=y
> +CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_FSL_NFC=y
> +CONFIG_MTD_NAND_FSL_NFC_SWECC=y
> +CONFIG_BLK_DEV_RAM=y
> +CONFIG_MISC_DEVICES=y
> +CONFIG_MVF_ADC=y
> +CONFIG_EEPROM_AT24=y
> +CONFIG_SCSI=y
> +CONFIG_BLK_DEV_SD=y
> +CONFIG_SCSI_MULTI_LUN=y
> +# CONFIG_SCSI_LOWLEVEL is not set
> +CONFIG_NETDEVICES=y
> +CONFIG_MICREL_PHY=y
> +CONFIG_NET_ETHERNET=y
> +CONFIG_FEC1=y
> +# CONFIG_NETDEV_1000 is not set
> +# CONFIG_NETDEV_10000 is not set
> +CONFIG_INPUT_POLLDEV=y
> +CONFIG_INPUT_EVDEV=y
> +CONFIG_KEYBOARD_GPIO=y
> +# CONFIG_INPUT_MOUSE is not set
> +CONFIG_INPUT_TOUCHSCREEN=y
> +CONFIG_INPUT_MISC=y
> +CONFIG_INPUT_UINPUT=y
> +# CONFIG_CONSOLE_TRANSLATIONS is not set # CONFIG_LEGACY_PTYS is not
> +set CONFIG_SERIAL_IMX=y CONFIG_SERIAL_IMX_CONSOLE=y CONFIG_HW_RANDOM=y
> +CONFIG_I2C=y CONFIG_I2C_CHARDEV=y CONFIG_I2C_IMX=y CONFIG_SPI=y
> +CONFIG_SPI_MVF_QSPI=m CONFIG_SPI_MVF=m CONFIG_SPI_SPIDEV=m
> +CONFIG_GPIO_SYSFS=y # CONFIG_HWMON is not set CONFIG_WATCHDOG=y
> +CONFIG_IMX2_WDT=y # CONFIG_MFD_MXC_HDMI is not set CONFIG_FB=y
> +CONFIG_FB_MVF_DCU=y CONFIG_MVF_TDA_998X=y CONFIG_FRAMEBUFFER_CONSOLE=y
> +CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
> +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
> +CONFIG_FONTS=y
> +CONFIG_FONT_8x8=y
> +CONFIG_FONT_8x16=y
> +CONFIG_LOGO=y
> +CONFIG_SOUND=y
> +# CONFIG_SOUND_OSS_CORE_PRECLAIM is not set CONFIG_SND=y
> +CONFIG_SND_PCM_OSS=y CONFIG_SND_SOC=y # CONFIG_SND_SOC_PCM052_SGTL5000
> +is not set # CONFIG_HID_SUPPORT is not set CONFIG_USB=y
> +CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ARC=y
> +CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y
> +CONFIG_USB_ETH=m CONFIG_MMC=y CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_PLTFM=y CONFIG_MMC_SDHCI_ESDHC_IMX=y CONFIG_NEW_LEDS=y
> +CONFIG_LEDS_CLASS=y CONFIG_LEDS_GPIO=y CONFIG_LEDS_TRIGGERS=y
> +CONFIG_LEDS_TRIGGER_TIMER=y CONFIG_LEDS_TRIGGER_HEARTBEAT=y
> +CONFIG_LEDS_TRIGGER_BACKLIGHT=y CONFIG_LEDS_TRIGGER_GPIO=y
> +CONFIG_LEDS_TRIGGER_DEFAULT_ON=y CONFIG_RTC_CLASS=y
> +CONFIG_RTC_DRV_SNVS=y CONFIG_DMADEVICES=y # CONFIG_MXC_HMP4E is not set
> +# CONFIG_MXC_HWEVENT is not set CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y #
> +CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set CONFIG_EXT4_FS=y
> +CONFIG_AUTOFS4_FS=y CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y CONFIG_TMPFS=y
> +CONFIG_JFFS2_FS=y CONFIG_CRAMFS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y
> +CONFIG_ROOT_NFS=y CONFIG_PARTITION_ADVANCED=y CONFIG_EFI_PARTITION=y
> +CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ASCII=m CONFIG_NLS_ISO8859_1=y
> +CONFIG_NLS_UTF8=m CONFIG_FTRACE=y CONFIG_ENABLE_DEFAULT_TRACERS=y
> +CONFIG_CRYPTO_TEST=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_ECB=y
> +CONFIG_CRYPTO_MICHAEL_MIC=y CONFIG_CRYPTO_AES=y CONFIG_CRYPTO_ARC4=y
> +CONFIG_CRYPTO_DEFLATE=y CONFIG_CRYPTO_LZO=y # CONFIG_CRYPTO_ANSI_CPRNG
> +is not set CONFIG_CRC_CCITT=m
> diff --git a/recipes-kernel/linux/linux-timesys_3.0.15.bb b/recipes-
> kernel/linux/linux-timesys_3.0.15.bb
> index 4c28f11..bc8b077 100644
> --- a/recipes-kernel/linux/linux-timesys_3.0.15.bb
> +++ b/recipes-kernel/linux/linux-timesys_3.0.15.bb
> @@ -13,6 +13,8 @@ SRC_URI_append_twr-vf65gs10 = "file://0001-mvf_fec.c-Fix-
> mac-address-read-to-mat
>
> SRCBRANCH_twr-vf65gs10 = "3.0.15_vybrid-twr"
> SRCREV_twr-vf65gs10 = "50c4c848d6b8743894cfcec166db475ef6140504"
> +SRCBRANCH_pcl052 = "3.0-pcl052"
> +SRCREV_pcl052 = "655f7949b5fd0b66bde03fc3c63c7a436353b1e1"
> LOCALVERSION = "-3.0-mvf+yocto"
>
> COMPATIBLE_MACHINE = "(vf60)"
> --
> 1.9.0
>
> _______________________________________________
> meta-freescale mailing list
> meta-freescale@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 4/4] pcm052: Add machine definition
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 4/4] pcm052: " Anthony Felice
@ 2014-02-27 19:44 ` Daiane.Angolini
2014-02-27 20:39 ` Otavio Salvador
1 sibling, 0 replies; 17+ messages in thread
From: Daiane.Angolini @ 2014-02-27 19:44 UTC (permalink / raw)
To: Anthony Felice, meta-freescale
> -----Original Message-----
> From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
> bounces@yoctoproject.org] On Behalf Of Anthony Felice
> Sent: Thursday, February 27, 2014 3:48 PM
> To: meta-freescale@yoctoproject.org
> Subject: [meta-freescale] [meta-fsl-arm][PATCH 4/4] pcm052: Add machine
> definition
>
> Add machine definition for the Phytec phyCORE Vybrid board.
Reviewed-by,
Daiane
>
> Signed-off-by: Anthony Felice <tony.felice@timesys.com>
> ---
> conf/machine/pcm052.conf | 22 +++
> .../linux/linux-timesys-3.0.15/pcm052/defconfig | 163
> +++++++++++++++++++++
> recipes-kernel/linux/linux-timesys_3.0.15.bb | 2 +
> 3 files changed, 187 insertions(+)
> create mode 100644 conf/machine/pcm052.conf create mode 100644 recipes-
> kernel/linux/linux-timesys-3.0.15/pcm052/defconfig
>
> diff --git a/conf/machine/pcm052.conf b/conf/machine/pcm052.conf new file
> mode 100644 index 0000000..d86fdb0
> --- /dev/null
> +++ b/conf/machine/pcm052.conf
> @@ -0,0 +1,22 @@
> +#@TYPE: Machine
> +#@NAME: Phytec phyCORE Vybrid Development Kit
> +#@SOC: vf60
> +#@DESCRIPTION: Machine configuration for Phytec phyCORE Vybrid
> +Development Kit
> +#@MAINTAINER: Anthony Felice <tony.felice@timesys.com>
> +
> +include conf/machine/include/imx-base.inc include
> +conf/machine/include/tune-cortexa5.inc
> +
> +SOC_FAMILY = "vf60"
> +
> +PREFERRED_PROVIDER_virtual/kernel = "linux-timesys"
> +PREFERRED_PROVIDER_u-boot = "u-boot-timesys"
> +
> +UBOOT_MACHINE = "pcm052_config"
> +
> +SDCARD_ROOTFS ?= "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.ext3"
> +IMAGE_FSTYPES ?= "tar.bz2 ext3 sdcard"
> +
> +SERIAL_CONSOLE = "115200 ttymxc1"
> +
> +MACHINE_FEATURES = "apm usbgadget usbhost vfat alsa touchscreen"
> diff --git a/recipes-kernel/linux/linux-timesys-3.0.15/pcm052/defconfig
> b/recipes-kernel/linux/linux-timesys-3.0.15/pcm052/defconfig
> new file mode 100644
> index 0000000..cb6419a
> --- /dev/null
> +++ b/recipes-kernel/linux/linux-timesys-3.0.15/pcm052/defconfig
> @@ -0,0 +1,163 @@
> +CONFIG_EXPERIMENTAL=y
> +CONFIG_SYSVIPC=y
> +CONFIG_IKCONFIG=y
> +CONFIG_IKCONFIG_PROC=y
> +CONFIG_LOG_BUF_SHIFT=14
> +CONFIG_EMBEDDED=y
> +# CONFIG_PERF_EVENTS is not set
> +CONFIG_PROFILING=y
> +CONFIG_MODULES=y
> +CONFIG_MODULE_UNLOAD=y
> +CONFIG_MODULE_FORCE_UNLOAD=y
> +CONFIG_MODVERSIONS=y
> +# CONFIG_BLK_DEV_BSG is not set
> +CONFIG_ARCH_MXC=y
> +CONFIG_ARCH_MVF=y
> +CONFIG_MACH_PCM052=y
> +CONFIG_MXC_PWM=y
> +CONFIG_MXC_USE_PIT=y
> +CONFIG_DMA_ZONE_SIZE=16
> +# CONFIG_CACHE_L2X0 is not set
> +CONFIG_ARM_ERRATA_743622=y
> +CONFIG_ARM_ERRATA_754322=y
> +CONFIG_HIGH_RES_TIMERS=y
> +CONFIG_VMSPLIT_2G=y
> +CONFIG_AEABI=y
> +# CONFIG_OABI_COMPAT is not set
> +CONFIG_COMPACTION=y
> +CONFIG_KSM=y
> +CONFIG_ZBOOT_ROM_TEXT=0x0
> +CONFIG_ZBOOT_ROM_BSS=0x0
> +CONFIG_CMDLINE="root=/dev/nfs rw
> nfsroot=10.193.20.106:/tftpboot/10.193.20.115
> ip=10.193.20.115:10.193.20.106:10.193.20.254:255.255.255.0::eth0:off
> console=ttymxc1,115200 mem=128M"
> +CONFIG_VFP=y
> +CONFIG_NEON=y
> +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_SUSPEND is
> +not set CONFIG_PM_RUNTIME=y CONFIG_NET=y CONFIG_PACKET=y CONFIG_UNIX=y
> +CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_IP_PNP=y
> +CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_LRO is not set
> +# CONFIG_IPV6 is not set CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
> +CONFIG_DEVTMPFS=y
> +CONFIG_DEVTMPFS_MOUNT=y
> +CONFIG_MTD=y
> +CONFIG_MTD_CMDLINE_PARTS=y
> +CONFIG_MTD_CHAR=y
> +CONFIG_MTD_BLOCK=y
> +CONFIG_MTD_M25P80=y
> +# CONFIG_M25PXX_USE_FAST_READ is not set CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_FSL_NFC=y CONFIG_MTD_NAND_FSL_NFC_SWECC=y
> +CONFIG_BLK_DEV_RAM=y CONFIG_MISC_DEVICES=y CONFIG_MVF_ADC=y
> +CONFIG_EEPROM_AT24=y CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y
> +CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_LOWLEVEL is not set
> +CONFIG_NETDEVICES=y CONFIG_MICREL_PHY=y CONFIG_NET_ETHERNET=y
> +CONFIG_FEC1=y # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is
> +not set CONFIG_INPUT_POLLDEV=y CONFIG_INPUT_EVDEV=y
> +CONFIG_KEYBOARD_GPIO=y # CONFIG_INPUT_MOUSE is not set
> +CONFIG_INPUT_TOUCHSCREEN=y CONFIG_TOUCHSCREEN_STMPE=y
> +CONFIG_INPUT_MISC=y CONFIG_INPUT_UINPUT=y # CONFIG_CONSOLE_TRANSLATIONS
> +is not set # CONFIG_LEGACY_PTYS is not set CONFIG_SERIAL_IMX=y
> +CONFIG_SERIAL_IMX_CONSOLE=y CONFIG_HW_RANDOM=y CONFIG_I2C=y
> +CONFIG_I2C_CHARDEV=y CONFIG_I2C_IMX=y CONFIG_SPI=y
> +CONFIG_SPI_MVF_QSPI=y CONFIG_SPI_SPIDEV=y CONFIG_GPIO_SYSFS=y #
> +CONFIG_HWMON is not set CONFIG_WATCHDOG=y CONFIG_IMX2_WDT=y
> +CONFIG_MFD_STMPE=y # CONFIG_MFD_MXC_HDMI is not set CONFIG_FB=y
> +CONFIG_FB_MVF_DCU=y CONFIG_BACKLIGHT_LCD_SUPPORT=y
> +CONFIG_BACKLIGHT_CLASS_DEVICE=y CONFIG_BACKLIGHT_GENERIC=m
> +CONFIG_BACKLIGHT_PWM=y CONFIG_FRAMEBUFFER_CONSOLE=y
> +CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
> +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
> +CONFIG_FONTS=y
> +CONFIG_FONT_8x8=y
> +CONFIG_FONT_8x16=y
> +CONFIG_LOGO=y
> +CONFIG_SOUND=y
> +# CONFIG_SOUND_OSS_CORE_PRECLAIM is not set CONFIG_SND=y
> +CONFIG_SND_PCM_OSS=y CONFIG_SND_SOC=y # CONFIG_HID_SUPPORT is not set
> +CONFIG_USB=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ARC=y
> +CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_USB_STORAGE=y CONFIG_USB_GADGET=y
> +CONFIG_USB_ETH=m CONFIG_MMC=y CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_PLTFM=y CONFIG_MMC_SDHCI_ESDHC_IMX=y
> +CONFIG_RTC_CLASS=y CONFIG_RTC_DRV_SNVS=y CONFIG_DMADEVICES=y #
> +CONFIG_MXC_HMP4E is not set # CONFIG_MXC_HWEVENT is not set
> +CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y # CONFIG_EXT3_DEFAULTS_TO_ORDERED is
> +not set CONFIG_EXT4_FS=y CONFIG_AUTOFS4_FS=y CONFIG_MSDOS_FS=y
> +CONFIG_VFAT_FS=y CONFIG_TMPFS=y CONFIG_JFFS2_FS=y CONFIG_CRAMFS=y
> +CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_ROOT_NFS=y
> +CONFIG_PARTITION_ADVANCED=y CONFIG_EFI_PARTITION=y
> +CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ASCII=m CONFIG_NLS_ISO8859_1=y
> +CONFIG_NLS_UTF8=m CONFIG_FTRACE=y CONFIG_ENABLE_DEFAULT_TRACERS=y
> +CONFIG_CRYPTO_TEST=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_ECB=y
> +CONFIG_CRYPTO_MICHAEL_MIC=y CONFIG_CRYPTO_AES=y CONFIG_CRYPTO_ARC4=y
> +CONFIG_CRYPTO_DEFLATE=y CONFIG_CRYPTO_LZO=y # CONFIG_CRYPTO_ANSI_CPRNG
> +is not set CONFIG_CRC_CCITT=m
> diff --git a/recipes-kernel/linux/linux-timesys_3.0.15.bb b/recipes-
> kernel/linux/linux-timesys_3.0.15.bb
> index bc8b077..c0784c0 100644
> --- a/recipes-kernel/linux/linux-timesys_3.0.15.bb
> +++ b/recipes-kernel/linux/linux-timesys_3.0.15.bb
> @@ -15,6 +15,8 @@ SRCBRANCH_twr-vf65gs10 = "3.0.15_vybrid-twr"
> SRCREV_twr-vf65gs10 = "50c4c848d6b8743894cfcec166db475ef6140504"
> SRCBRANCH_pcl052 = "3.0-pcl052"
> SRCREV_pcl052 = "655f7949b5fd0b66bde03fc3c63c7a436353b1e1"
> +SRCBRANCH_pcm052 = "3.0-pcm052"
> +SRCREV_pcm052 = "7a27fd26d2b5b732e12ecea13a846679cbafe9a9"
> LOCALVERSION = "-3.0-mvf+yocto"
>
> COMPATIBLE_MACHINE = "(vf60)"
> --
> 1.9.0
>
> _______________________________________________
> meta-freescale mailing list
> meta-freescale@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards
2014-02-27 18:47 [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards Anthony Felice
` (3 preceding siblings ...)
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 4/4] pcm052: " Anthony Felice
@ 2014-02-27 19:47 ` Daiane.Angolini
2014-02-27 20:34 ` Tony Felice
2014-02-27 20:41 ` Otavio Salvador
5 siblings, 1 reply; 17+ messages in thread
From: Daiane.Angolini @ 2014-02-27 19:47 UTC (permalink / raw)
To: Anthony Felice, meta-freescale
> -----Original Message-----
> From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
> bounces@yoctoproject.org] On Behalf Of Anthony Felice
> Sent: Thursday, February 27, 2014 3:48 PM
> To: meta-freescale@yoctoproject.org
> Subject: [meta-freescale] [meta-fsl-arm][PATCH 0/4] Add support for Phytec
> Vybrid boards
>
> This series adds support for the Phytec Cosmic Vybrid (pcl052) and Phytec
> phyCORE Vybrid (pcm052) machines.
>
> The first patch adds a modified u-boot 2011.12 with board support enabled
> for these two machines, as the pcl052 and pcm052 are not supported in
> mainline u-boot.
>
> The second patch reworks the linux-timesys recipe to use the twr-vf65gs10
> machine name for sources. This is in preparation for the Phytec board
> support addition, as the Phytec machine names will also be used for
> sources.
>
> The third patch adds the machine definition for the pcl052 board.
>
> The fourth patch adds the machine definition for the pcm052 board.
>
Very nice, Anthony!
Thanks a lot for sending those new board support files ;-)
I have reviewed and nothing special. Only double check the copyright and the COMPATIBLE_MACHINE,
but if you think the patches are OK, I´m fine
(i´m sorry I have reviewed the patches in the wrong order... when I realized it was too late)
Daiane
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 1/4] u-boot-timesys: Add version 2011.12
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 1/4] u-boot-timesys: Add version 2011.12 Anthony Felice
2014-02-27 19:37 ` Daiane.Angolini
@ 2014-02-27 20:34 ` Otavio Salvador
1 sibling, 0 replies; 17+ messages in thread
From: Otavio Salvador @ 2014-02-27 20:34 UTC (permalink / raw)
To: Anthony Felice; +Cc: meta-freescale
Hello Anthony,
On Thu, Feb 27, 2014 at 3:47 PM, Anthony Felice <tony.felice@timesys.com> wrote:
> Add some commits over u-boot 2011.12 with board support for the pcl052 and
> pcm052 platforms, that include:
>
> * Add NAND boot support
> * Add FEC1 support
> * Fix DDR3 settings for pcm052 1.1 silicon
> * Fix SDHC issues
> * New machine definitions (i.e. pcl052, pcm052)
>
> and more, for a total of 25 commits. Included in these commits is also base
> support for the Vybrid Tower platform.
>
> Commits from the u-boot-cfi-flash fork from 2012-03-21 and earlier have also
> been added, starting from commit 85c344e5f98: "cfi: fix the incomplete erased
> status check in buffer write".
>
> This version has been tested on the pcl052 and pcm052 platforms.
>
> Signed-off-by: Anthony Felice <tony.felice@timesys.com>
Your commit log is nice now; thanks!
The only remark I have is that Vybrid Tower platform is currently
using the mainline U-Boot (2013.01) so this recipe should go to
meta-fsl-arm-extra.
In the ideal World, it'd be nice if we could have those platforms
added there as well, so we reduce the amount of maintenance work we
have.
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards
2014-02-27 19:47 ` [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards Daiane.Angolini
@ 2014-02-27 20:34 ` Tony Felice
0 siblings, 0 replies; 17+ messages in thread
From: Tony Felice @ 2014-02-27 20:34 UTC (permalink / raw)
To: Daiane.Angolini; +Cc: meta-freescale
Hi Daiane,
Thanks for reviewing these commits!
For the first patch, I will resubmit this with a copyright line for the
u-boot-timesys recipe. I am not aware of a plan to move to mainline
u-boot on the Phytec Vybrid machines.
For the second patch, I think this actually might not be necessary - I
had originally planned to have a machine specific SRCREV and SRCBRANCH
for each Vybrid board, but I think I can actually leave the generic
SRCREV and SRCBRANCH for the twr-vf65gs10 to use (and for a default use
case), and a machine specific SRCREV and SRCBRANCH for the Phytec
boards. I will do some testing and resubmit the patches.
Thanks,
Tony
On Thu, 2014-02-27 at 14:47 -0500, Daiane.Angolini@freescale.com wrote:
>
> > -----Original Message-----
> > From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
> > bounces@yoctoproject.org] On Behalf Of Anthony Felice
> > Sent: Thursday, February 27, 2014 3:48 PM
> > To: meta-freescale@yoctoproject.org
> > Subject: [meta-freescale] [meta-fsl-arm][PATCH 0/4] Add support for Phytec
> > Vybrid boards
> >
> > This series adds support for the Phytec Cosmic Vybrid (pcl052) and Phytec
> > phyCORE Vybrid (pcm052) machines.
> >
> > The first patch adds a modified u-boot 2011.12 with board support enabled
> > for these two machines, as the pcl052 and pcm052 are not supported in
> > mainline u-boot.
> >
> > The second patch reworks the linux-timesys recipe to use the twr-vf65gs10
> > machine name for sources. This is in preparation for the Phytec board
> > support addition, as the Phytec machine names will also be used for
> > sources.
> >
> > The third patch adds the machine definition for the pcl052 board.
> >
> > The fourth patch adds the machine definition for the pcm052 board.
> >
>
>
> Very nice, Anthony!
>
> Thanks a lot for sending those new board support files ;-)
>
> I have reviewed and nothing special. Only double check the copyright and the COMPATIBLE_MACHINE,
> but if you think the patches are OK, I´m fine
>
> (i´m sorry I have reviewed the patches in the wrong order... when I realized it was too late)
>
> Daiane
>
--
Tony Felice
Vybrid Technical Lead
Timesys Corporation
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 3/4] pcl052: Add machine definition
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 3/4] pcl052: Add machine definition Anthony Felice
2014-02-27 19:43 ` Daiane.Angolini
@ 2014-02-27 20:37 ` Otavio Salvador
2014-02-28 12:07 ` Daiane.Angolini
1 sibling, 1 reply; 17+ messages in thread
From: Otavio Salvador @ 2014-02-27 20:37 UTC (permalink / raw)
To: Anthony Felice; +Cc: meta-freescale
On Thu, Feb 27, 2014 at 3:47 PM, Anthony Felice <tony.felice@timesys.com> wrote:
> Add machine definition for the Phytec Cosmic Vybrid board.
>
> Signed-off-by: Anthony Felice <tony.felice@timesys.com>
This is not a Freescale reference board so ought to be in -extra.
Please also check our Documentation project and add the corresponding
Documentation updates.
> ---
> conf/machine/pcl052.conf | 22 +++
> .../linux/linux-timesys-3.0.15/pcl052/defconfig | 168 +++++++++++++++++++++
> recipes-kernel/linux/linux-timesys_3.0.15.bb | 2 +
> 3 files changed, 192 insertions(+)
> create mode 100644 conf/machine/pcl052.conf
> create mode 100644 recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
>
> diff --git a/conf/machine/pcl052.conf b/conf/machine/pcl052.conf
> new file mode 100644
> index 0000000..611e93d
> --- /dev/null
> +++ b/conf/machine/pcl052.conf
> @@ -0,0 +1,22 @@
> +#@TYPE: Machine
> +#@NAME: Phytec Cosmic Vybrid Development Kit
> +#@SOC: vf60
> +#@DESCRIPTION: Machine configuration for Phytec Cosmic Vybrid Development Kit
> +#@MAINTAINER: Anthony Felice <tony.felice@timesys.com>
> +
> +include conf/machine/include/imx-base.inc
> +include conf/machine/include/tune-cortexa5.inc
> +
> +SOC_FAMILY = "vf60"
> +
> +PREFERRED_PROVIDER_virtual/kernel = "linux-timesys"
> +PREFERRED_PROVIDER_u-boot = "u-boot-timesys"
> +
> +UBOOT_MACHINE = "pcl052_config"
> +
> +SDCARD_ROOTFS ?= "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.ext3"
> +IMAGE_FSTYPES ?= "tar.bz2 ext3 sdcard"
> +
> +SERIAL_CONSOLE = "115200 ttymxc1"
> +
> +MACHINE_FEATURES = "apm usbgadget usbhost vfat alsa"
> diff --git a/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig b/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
> new file mode 100644
> index 0000000..3b6f1a6
> --- /dev/null
> +++ b/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
This ought to be another commit (before machine addition).
> @@ -0,0 +1,168 @@
> +CONFIG_EXPERIMENTAL=y
> +CONFIG_LOCALVERSION="-3.0-mvf+yocto"
> +CONFIG_SYSVIPC=y
> +CONFIG_IKCONFIG=y
> +CONFIG_IKCONFIG_PROC=y
> +CONFIG_LOG_BUF_SHIFT=14
> +CONFIG_EMBEDDED=y
> +# CONFIG_PERF_EVENTS is not set
> +CONFIG_PROFILING=y
> +CONFIG_MODULES=y
> +CONFIG_MODULE_UNLOAD=y
> +CONFIG_MODULE_FORCE_UNLOAD=y
> +CONFIG_MODVERSIONS=y
> +# CONFIG_BLK_DEV_BSG is not set
> +CONFIG_ARCH_MXC=y
> +CONFIG_ARCH_MVF=y
> +CONFIG_MACH_PCL052=y
> +CONFIG_MXC_PWM=m
> +CONFIG_MXC_USE_PIT=y
> +CONFIG_DMA_ZONE_SIZE=16
> +# CONFIG_CACHE_L2X0 is not set
> +CONFIG_ARM_ERRATA_743622=y
> +CONFIG_ARM_ERRATA_754322=y
> +CONFIG_HIGH_RES_TIMERS=y
> +CONFIG_VMSPLIT_2G=y
> +CONFIG_AEABI=y
> +# CONFIG_OABI_COMPAT is not set
> +CONFIG_COMPACTION=y
> +CONFIG_KSM=y
> +CONFIG_ZBOOT_ROM_TEXT=0x0
> +CONFIG_ZBOOT_ROM_BSS=0x0
> +CONFIG_CMDLINE="root=/dev/nfs rw nfsroot=10.193.20.106:/tftpboot/10.193.20.115 ip=10.193.20.115:10.193.20.106:10.193.20.254:255.255.255.0::eth0:off console=ttymxc1,115200 mem=128M"
> +CONFIG_VFP=y
> +CONFIG_NEON=y
> +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
> +# CONFIG_SUSPEND is not set
> +CONFIG_PM_RUNTIME=y
> +CONFIG_NET=y
> +CONFIG_PACKET=y
> +CONFIG_UNIX=y
> +CONFIG_INET=y
> +CONFIG_IP_MULTICAST=y
> +CONFIG_IP_PNP=y
> +CONFIG_IP_PNP_DHCP=y
> +CONFIG_IP_PNP_BOOTP=y
> +# CONFIG_INET_LRO is not set
> +# CONFIG_IPV6 is not set
> +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
> +CONFIG_DEVTMPFS=y
> +CONFIG_DEVTMPFS_MOUNT=y
> +CONFIG_MTD=y
> +CONFIG_MTD_CMDLINE_PARTS=y
> +CONFIG_MTD_CHAR=y
> +CONFIG_MTD_BLOCK=y
> +CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_FSL_NFC=y
> +CONFIG_MTD_NAND_FSL_NFC_SWECC=y
> +CONFIG_BLK_DEV_RAM=y
> +CONFIG_MISC_DEVICES=y
> +CONFIG_MVF_ADC=y
> +CONFIG_EEPROM_AT24=y
> +CONFIG_SCSI=y
> +CONFIG_BLK_DEV_SD=y
> +CONFIG_SCSI_MULTI_LUN=y
> +# CONFIG_SCSI_LOWLEVEL is not set
> +CONFIG_NETDEVICES=y
> +CONFIG_MICREL_PHY=y
> +CONFIG_NET_ETHERNET=y
> +CONFIG_FEC1=y
> +# CONFIG_NETDEV_1000 is not set
> +# CONFIG_NETDEV_10000 is not set
> +CONFIG_INPUT_POLLDEV=y
> +CONFIG_INPUT_EVDEV=y
> +CONFIG_KEYBOARD_GPIO=y
> +# CONFIG_INPUT_MOUSE is not set
> +CONFIG_INPUT_TOUCHSCREEN=y
> +CONFIG_INPUT_MISC=y
> +CONFIG_INPUT_UINPUT=y
> +# CONFIG_CONSOLE_TRANSLATIONS is not set
> +# CONFIG_LEGACY_PTYS is not set
> +CONFIG_SERIAL_IMX=y
> +CONFIG_SERIAL_IMX_CONSOLE=y
> +CONFIG_HW_RANDOM=y
> +CONFIG_I2C=y
> +CONFIG_I2C_CHARDEV=y
> +CONFIG_I2C_IMX=y
> +CONFIG_SPI=y
> +CONFIG_SPI_MVF_QSPI=m
> +CONFIG_SPI_MVF=m
> +CONFIG_SPI_SPIDEV=m
> +CONFIG_GPIO_SYSFS=y
> +# CONFIG_HWMON is not set
> +CONFIG_WATCHDOG=y
> +CONFIG_IMX2_WDT=y
> +# CONFIG_MFD_MXC_HDMI is not set
> +CONFIG_FB=y
> +CONFIG_FB_MVF_DCU=y
> +CONFIG_MVF_TDA_998X=y
> +CONFIG_FRAMEBUFFER_CONSOLE=y
> +CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
> +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
> +CONFIG_FONTS=y
> +CONFIG_FONT_8x8=y
> +CONFIG_FONT_8x16=y
> +CONFIG_LOGO=y
> +CONFIG_SOUND=y
> +# CONFIG_SOUND_OSS_CORE_PRECLAIM is not set
> +CONFIG_SND=y
> +CONFIG_SND_PCM_OSS=y
> +CONFIG_SND_SOC=y
> +# CONFIG_SND_SOC_PCM052_SGTL5000 is not set
> +# CONFIG_HID_SUPPORT is not set
> +CONFIG_USB=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_ARC=y
> +CONFIG_USB_EHCI_ROOT_HUB_TT=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_ETH=m
> +CONFIG_MMC=y
> +CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_PLTFM=y
> +CONFIG_MMC_SDHCI_ESDHC_IMX=y
> +CONFIG_NEW_LEDS=y
> +CONFIG_LEDS_CLASS=y
> +CONFIG_LEDS_GPIO=y
> +CONFIG_LEDS_TRIGGERS=y
> +CONFIG_LEDS_TRIGGER_TIMER=y
> +CONFIG_LEDS_TRIGGER_HEARTBEAT=y
> +CONFIG_LEDS_TRIGGER_BACKLIGHT=y
> +CONFIG_LEDS_TRIGGER_GPIO=y
> +CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
> +CONFIG_RTC_CLASS=y
> +CONFIG_RTC_DRV_SNVS=y
> +CONFIG_DMADEVICES=y
> +# CONFIG_MXC_HMP4E is not set
> +# CONFIG_MXC_HWEVENT is not set
> +CONFIG_EXT2_FS=y
> +CONFIG_EXT3_FS=y
> +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
> +CONFIG_EXT4_FS=y
> +CONFIG_AUTOFS4_FS=y
> +CONFIG_MSDOS_FS=y
> +CONFIG_VFAT_FS=y
> +CONFIG_TMPFS=y
> +CONFIG_JFFS2_FS=y
> +CONFIG_CRAMFS=y
> +CONFIG_NFS_FS=y
> +CONFIG_NFS_V3=y
> +CONFIG_ROOT_NFS=y
> +CONFIG_PARTITION_ADVANCED=y
> +CONFIG_EFI_PARTITION=y
> +CONFIG_NLS_CODEPAGE_437=y
> +CONFIG_NLS_ASCII=m
> +CONFIG_NLS_ISO8859_1=y
> +CONFIG_NLS_UTF8=m
> +CONFIG_FTRACE=y
> +CONFIG_ENABLE_DEFAULT_TRACERS=y
> +CONFIG_CRYPTO_TEST=m
> +CONFIG_CRYPTO_CBC=y
> +CONFIG_CRYPTO_ECB=y
> +CONFIG_CRYPTO_MICHAEL_MIC=y
> +CONFIG_CRYPTO_AES=y
> +CONFIG_CRYPTO_ARC4=y
> +CONFIG_CRYPTO_DEFLATE=y
> +CONFIG_CRYPTO_LZO=y
> +# CONFIG_CRYPTO_ANSI_CPRNG is not set
> +CONFIG_CRC_CCITT=m
> diff --git a/recipes-kernel/linux/linux-timesys_3.0.15.bb b/recipes-kernel/linux/linux-timesys_3.0.15.bb
> index 4c28f11..bc8b077 100644
> --- a/recipes-kernel/linux/linux-timesys_3.0.15.bb
> +++ b/recipes-kernel/linux/linux-timesys_3.0.15.bb
> @@ -13,6 +13,8 @@ SRC_URI_append_twr-vf65gs10 = "file://0001-mvf_fec.c-Fix-mac-address-read-to-mat
>
> SRCBRANCH_twr-vf65gs10 = "3.0.15_vybrid-twr"
> SRCREV_twr-vf65gs10 = "50c4c848d6b8743894cfcec166db475ef6140504"
> +SRCBRANCH_pcl052 = "3.0-pcl052"
> +SRCREV_pcl052 = "655f7949b5fd0b66bde03fc3c63c7a436353b1e1"
> LOCALVERSION = "-3.0-mvf+yocto"
>
> COMPATIBLE_MACHINE = "(vf60)"
> --
> 1.9.0
>
> _______________________________________________
> meta-freescale mailing list
> meta-freescale@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 4/4] pcm052: Add machine definition
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 4/4] pcm052: " Anthony Felice
2014-02-27 19:44 ` Daiane.Angolini
@ 2014-02-27 20:39 ` Otavio Salvador
1 sibling, 0 replies; 17+ messages in thread
From: Otavio Salvador @ 2014-02-27 20:39 UTC (permalink / raw)
To: Anthony Felice; +Cc: meta-freescale
On Thu, Feb 27, 2014 at 3:47 PM, Anthony Felice <tony.felice@timesys.com> wrote:
> Add machine definition for the Phytec phyCORE Vybrid board.
>
> Signed-off-by: Anthony Felice <tony.felice@timesys.com>
Same comments as for the other Phytec board.
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards
2014-02-27 18:47 [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards Anthony Felice
` (4 preceding siblings ...)
2014-02-27 19:47 ` [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards Daiane.Angolini
@ 2014-02-27 20:41 ` Otavio Salvador
2014-02-27 21:03 ` Tony Felice
5 siblings, 1 reply; 17+ messages in thread
From: Otavio Salvador @ 2014-02-27 20:41 UTC (permalink / raw)
To: Anthony Felice; +Cc: meta-freescale
Hello Anthony,
On Thu, Feb 27, 2014 at 3:47 PM, Anthony Felice <tony.felice@timesys.com> wrote:
> This series adds support for the Phytec Cosmic Vybrid (pcl052) and Phytec phyCORE Vybrid (pcm052) machines.
Those are -extra material as are not FSL reference boards.
> The first patch adds a modified u-boot 2011.12 with board support enabled for these two machines, as the pcl052 and pcm052 are not supported in mainline u-boot.
Extra.
> The second patch reworks the linux-timesys recipe to use the twr-vf65gs10 machine name for sources. This is in preparation for the Phytec board support addition, as the Phytec machine names will also be used for sources.
>
> The third patch adds the machine definition for the pcl052 board.
>
> The fourth patch adds the machine definition for the pcm052 board.
Please also work on the Documentation update so it is added to the
reference manual.
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards
2014-02-27 20:41 ` Otavio Salvador
@ 2014-02-27 21:03 ` Tony Felice
0 siblings, 0 replies; 17+ messages in thread
From: Tony Felice @ 2014-02-27 21:03 UTC (permalink / raw)
To: Otavio Salvador; +Cc: meta-freescale
Hi Otavio,
Thanks for reviewing these patches!
I will make the requested changes and resubmit the patchset.
Thanks,
Tony
On Thu, 2014-02-27 at 15:41 -0500, Otavio Salvador wrote:
> Hello Anthony,
>
> On Thu, Feb 27, 2014 at 3:47 PM, Anthony Felice <tony.felice@timesys.com> wrote:
> > This series adds support for the Phytec Cosmic Vybrid (pcl052) and Phytec phyCORE Vybrid (pcm052) machines.
>
> Those are -extra material as are not FSL reference boards.
>
> > The first patch adds a modified u-boot 2011.12 with board support enabled for these two machines, as the pcl052 and pcm052 are not supported in mainline u-boot.
>
> Extra.
>
> > The second patch reworks the linux-timesys recipe to use the twr-vf65gs10 machine name for sources. This is in preparation for the Phytec board support addition, as the Phytec machine names will also be used for sources.
> >
> > The third patch adds the machine definition for the pcl052 board.
> >
> > The fourth patch adds the machine definition for the pcm052 board.
>
> Please also work on the Documentation update so it is added to the
> reference manual.
>
--
Tony Felice
Vybrid Technical Lead
Timesys Corporation
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [meta-fsl-arm][PATCH 3/4] pcl052: Add machine definition
2014-02-27 20:37 ` Otavio Salvador
@ 2014-02-28 12:07 ` Daiane.Angolini
0 siblings, 0 replies; 17+ messages in thread
From: Daiane.Angolini @ 2014-02-28 12:07 UTC (permalink / raw)
To: Otavio Salvador, Anthony Felice; +Cc: meta-freescale
> -----Original Message-----
> From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
> bounces@yoctoproject.org] On Behalf Of Otavio Salvador
> Sent: Thursday, February 27, 2014 5:37 PM
> To: Anthony Felice
> Cc: meta-freescale@yoctoproject.org
> Subject: Re: [meta-freescale] [meta-fsl-arm][PATCH 3/4] pcl052: Add machine
> definition
>
> On Thu, Feb 27, 2014 at 3:47 PM, Anthony Felice <tony.felice@timesys.com>
> wrote:
> > Add machine definition for the Phytec Cosmic Vybrid board.
> >
> > Signed-off-by: Anthony Felice <tony.felice@timesys.com>
>
> This is not a Freescale reference board so ought to be in -extra.
>
> Please also check our Documentation project and add the corresponding
> Documentation updates.
Ops, Thanks a lot, Otavio! I completely forgot about #RN!
Anthony, please take a look in this email [1] in order to guide yourself on how to change docs
[1] http://article.gmane.org/gmane.linux.embedded.yocto.meta-freescale/6816
Regards,
Daiane
>
> > ---
> > conf/machine/pcl052.conf | 22 +++
> > .../linux/linux-timesys-3.0.15/pcl052/defconfig | 168
> +++++++++++++++++++++
> > recipes-kernel/linux/linux-timesys_3.0.15.bb | 2 +
> > 3 files changed, 192 insertions(+)
> > create mode 100644 conf/machine/pcl052.conf create mode 100644
> > recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
> >
> > diff --git a/conf/machine/pcl052.conf b/conf/machine/pcl052.conf new
> > file mode 100644 index 0000000..611e93d
> > --- /dev/null
> > +++ b/conf/machine/pcl052.conf
> > @@ -0,0 +1,22 @@
> > +#@TYPE: Machine
> > +#@NAME: Phytec Cosmic Vybrid Development Kit
> > +#@SOC: vf60
> > +#@DESCRIPTION: Machine configuration for Phytec Cosmic Vybrid
> > +Development Kit
> > +#@MAINTAINER: Anthony Felice <tony.felice@timesys.com>
> > +
> > +include conf/machine/include/imx-base.inc include
> > +conf/machine/include/tune-cortexa5.inc
> > +
> > +SOC_FAMILY = "vf60"
> > +
> > +PREFERRED_PROVIDER_virtual/kernel = "linux-timesys"
> > +PREFERRED_PROVIDER_u-boot = "u-boot-timesys"
> > +
> > +UBOOT_MACHINE = "pcl052_config"
> > +
> > +SDCARD_ROOTFS ?= "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.ext3"
> > +IMAGE_FSTYPES ?= "tar.bz2 ext3 sdcard"
> > +
> > +SERIAL_CONSOLE = "115200 ttymxc1"
> > +
> > +MACHINE_FEATURES = "apm usbgadget usbhost vfat alsa"
> > diff --git
> > a/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
> > b/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
> > new file mode 100644
> > index 0000000..3b6f1a6
> > --- /dev/null
> > +++ b/recipes-kernel/linux/linux-timesys-3.0.15/pcl052/defconfig
>
> This ought to be another commit (before machine addition).
>
> > @@ -0,0 +1,168 @@
> > +CONFIG_EXPERIMENTAL=y
> > +CONFIG_LOCALVERSION="-3.0-mvf+yocto"
> > +CONFIG_SYSVIPC=y
> > +CONFIG_IKCONFIG=y
> > +CONFIG_IKCONFIG_PROC=y
> > +CONFIG_LOG_BUF_SHIFT=14
> > +CONFIG_EMBEDDED=y
> > +# CONFIG_PERF_EVENTS is not set
> > +CONFIG_PROFILING=y
> > +CONFIG_MODULES=y
> > +CONFIG_MODULE_UNLOAD=y
> > +CONFIG_MODULE_FORCE_UNLOAD=y
> > +CONFIG_MODVERSIONS=y
> > +# CONFIG_BLK_DEV_BSG is not set
> > +CONFIG_ARCH_MXC=y
> > +CONFIG_ARCH_MVF=y
> > +CONFIG_MACH_PCL052=y
> > +CONFIG_MXC_PWM=m
> > +CONFIG_MXC_USE_PIT=y
> > +CONFIG_DMA_ZONE_SIZE=16
> > +# CONFIG_CACHE_L2X0 is not set
> > +CONFIG_ARM_ERRATA_743622=y
> > +CONFIG_ARM_ERRATA_754322=y
> > +CONFIG_HIGH_RES_TIMERS=y
> > +CONFIG_VMSPLIT_2G=y
> > +CONFIG_AEABI=y
> > +# CONFIG_OABI_COMPAT is not set
> > +CONFIG_COMPACTION=y
> > +CONFIG_KSM=y
> > +CONFIG_ZBOOT_ROM_TEXT=0x0
> > +CONFIG_ZBOOT_ROM_BSS=0x0
> > +CONFIG_CMDLINE="root=/dev/nfs rw
> nfsroot=10.193.20.106:/tftpboot/10.193.20.115
> ip=10.193.20.115:10.193.20.106:10.193.20.254:255.255.255.0::eth0:off
> console=ttymxc1,115200 mem=128M"
> > +CONFIG_VFP=y
> > +CONFIG_NEON=y
> > +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_SUSPEND is
> > +not set CONFIG_PM_RUNTIME=y CONFIG_NET=y CONFIG_PACKET=y
> > +CONFIG_UNIX=y CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_IP_PNP=y
> > +CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_LRO is not
> > +set # CONFIG_IPV6 is not set
> > +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
> > +CONFIG_DEVTMPFS=y
> > +CONFIG_DEVTMPFS_MOUNT=y
> > +CONFIG_MTD=y
> > +CONFIG_MTD_CMDLINE_PARTS=y
> > +CONFIG_MTD_CHAR=y
> > +CONFIG_MTD_BLOCK=y
> > +CONFIG_MTD_NAND=y
> > +CONFIG_MTD_NAND_FSL_NFC=y
> > +CONFIG_MTD_NAND_FSL_NFC_SWECC=y
> > +CONFIG_BLK_DEV_RAM=y
> > +CONFIG_MISC_DEVICES=y
> > +CONFIG_MVF_ADC=y
> > +CONFIG_EEPROM_AT24=y
> > +CONFIG_SCSI=y
> > +CONFIG_BLK_DEV_SD=y
> > +CONFIG_SCSI_MULTI_LUN=y
> > +# CONFIG_SCSI_LOWLEVEL is not set
> > +CONFIG_NETDEVICES=y
> > +CONFIG_MICREL_PHY=y
> > +CONFIG_NET_ETHERNET=y
> > +CONFIG_FEC1=y
> > +# CONFIG_NETDEV_1000 is not set
> > +# CONFIG_NETDEV_10000 is not set
> > +CONFIG_INPUT_POLLDEV=y
> > +CONFIG_INPUT_EVDEV=y
> > +CONFIG_KEYBOARD_GPIO=y
> > +# CONFIG_INPUT_MOUSE is not set
> > +CONFIG_INPUT_TOUCHSCREEN=y
> > +CONFIG_INPUT_MISC=y
> > +CONFIG_INPUT_UINPUT=y
> > +# CONFIG_CONSOLE_TRANSLATIONS is not set # CONFIG_LEGACY_PTYS is not
> > +set CONFIG_SERIAL_IMX=y CONFIG_SERIAL_IMX_CONSOLE=y
> > +CONFIG_HW_RANDOM=y CONFIG_I2C=y CONFIG_I2C_CHARDEV=y CONFIG_I2C_IMX=y
> > +CONFIG_SPI=y CONFIG_SPI_MVF_QSPI=m CONFIG_SPI_MVF=m
> > +CONFIG_SPI_SPIDEV=m CONFIG_GPIO_SYSFS=y # CONFIG_HWMON is not set
> > +CONFIG_WATCHDOG=y CONFIG_IMX2_WDT=y # CONFIG_MFD_MXC_HDMI is not set
> > +CONFIG_FB=y CONFIG_FB_MVF_DCU=y CONFIG_MVF_TDA_998X=y
> > +CONFIG_FRAMEBUFFER_CONSOLE=y
> > +CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
> > +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
> > +CONFIG_FONTS=y
> > +CONFIG_FONT_8x8=y
> > +CONFIG_FONT_8x16=y
> > +CONFIG_LOGO=y
> > +CONFIG_SOUND=y
> > +# CONFIG_SOUND_OSS_CORE_PRECLAIM is not set CONFIG_SND=y
> > +CONFIG_SND_PCM_OSS=y CONFIG_SND_SOC=y #
> > +CONFIG_SND_SOC_PCM052_SGTL5000 is not set # CONFIG_HID_SUPPORT is not
> > +set CONFIG_USB=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ARC=y
> > +CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_USB_STORAGE=y
> > +CONFIG_USB_GADGET=y CONFIG_USB_ETH=m CONFIG_MMC=y CONFIG_MMC_SDHCI=y
> > +CONFIG_MMC_SDHCI_PLTFM=y CONFIG_MMC_SDHCI_ESDHC_IMX=y
> > +CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y CONFIG_LEDS_GPIO=y
> > +CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=y
> > +CONFIG_LEDS_TRIGGER_HEARTBEAT=y CONFIG_LEDS_TRIGGER_BACKLIGHT=y
> > +CONFIG_LEDS_TRIGGER_GPIO=y CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
> > +CONFIG_RTC_CLASS=y CONFIG_RTC_DRV_SNVS=y CONFIG_DMADEVICES=y #
> > +CONFIG_MXC_HMP4E is not set # CONFIG_MXC_HWEVENT is not set
> > +CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y # CONFIG_EXT3_DEFAULTS_TO_ORDERED
> > +is not set CONFIG_EXT4_FS=y CONFIG_AUTOFS4_FS=y CONFIG_MSDOS_FS=y
> > +CONFIG_VFAT_FS=y CONFIG_TMPFS=y CONFIG_JFFS2_FS=y CONFIG_CRAMFS=y
> > +CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_ROOT_NFS=y
> > +CONFIG_PARTITION_ADVANCED=y CONFIG_EFI_PARTITION=y
> > +CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ASCII=m CONFIG_NLS_ISO8859_1=y
> > +CONFIG_NLS_UTF8=m CONFIG_FTRACE=y CONFIG_ENABLE_DEFAULT_TRACERS=y
> > +CONFIG_CRYPTO_TEST=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_ECB=y
> > +CONFIG_CRYPTO_MICHAEL_MIC=y CONFIG_CRYPTO_AES=y CONFIG_CRYPTO_ARC4=y
> > +CONFIG_CRYPTO_DEFLATE=y CONFIG_CRYPTO_LZO=y #
> > +CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRC_CCITT=m
> > diff --git a/recipes-kernel/linux/linux-timesys_3.0.15.bb
> > b/recipes-kernel/linux/linux-timesys_3.0.15.bb
> > index 4c28f11..bc8b077 100644
> > --- a/recipes-kernel/linux/linux-timesys_3.0.15.bb
> > +++ b/recipes-kernel/linux/linux-timesys_3.0.15.bb
> > @@ -13,6 +13,8 @@ SRC_URI_append_twr-vf65gs10 =
> > "file://0001-mvf_fec.c-Fix-mac-address-read-to-mat
> >
> > SRCBRANCH_twr-vf65gs10 = "3.0.15_vybrid-twr"
> > SRCREV_twr-vf65gs10 = "50c4c848d6b8743894cfcec166db475ef6140504"
> > +SRCBRANCH_pcl052 = "3.0-pcl052"
> > +SRCREV_pcl052 = "655f7949b5fd0b66bde03fc3c63c7a436353b1e1"
> > LOCALVERSION = "-3.0-mvf+yocto"
> >
> > COMPATIBLE_MACHINE = "(vf60)"
> > --
> > 1.9.0
> >
> > _______________________________________________
> > meta-freescale mailing list
> > meta-freescale@yoctoproject.org
> > https://lists.yoctoproject.org/listinfo/meta-freescale
>
>
>
> --
> Otavio Salvador O.S. Systems
> http://www.ossystems.com.br http://code.ossystems.com.br
> Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
> _______________________________________________
> meta-freescale mailing list
> meta-freescale@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/meta-freescale
>
^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2014-02-28 12:07 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-02-27 18:47 [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards Anthony Felice
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 1/4] u-boot-timesys: Add version 2011.12 Anthony Felice
2014-02-27 19:37 ` Daiane.Angolini
2014-02-27 20:34 ` Otavio Salvador
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 2/4] linux-timesys: Use twr-vf65gs10 machine name for sources Anthony Felice
2014-02-27 19:41 ` Daiane.Angolini
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 3/4] pcl052: Add machine definition Anthony Felice
2014-02-27 19:43 ` Daiane.Angolini
2014-02-27 20:37 ` Otavio Salvador
2014-02-28 12:07 ` Daiane.Angolini
2014-02-27 18:47 ` [meta-fsl-arm][PATCH 4/4] pcm052: " Anthony Felice
2014-02-27 19:44 ` Daiane.Angolini
2014-02-27 20:39 ` Otavio Salvador
2014-02-27 19:47 ` [meta-fsl-arm][PATCH 0/4] Add support for Phytec Vybrid boards Daiane.Angolini
2014-02-27 20:34 ` Tony Felice
2014-02-27 20:41 ` Otavio Salvador
2014-02-27 21:03 ` Tony Felice
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.