* [U-Boot] [PATCH v3 0/2] rockchip: Add support for MiQi board
@ 2017-03-29 23:23 Jernej Skrabec
2017-03-29 23:23 ` [U-Boot] [PATCH v3 1/2] rockchip: cosmetic: Sort RK3288 boards Jernej Skrabec
2017-03-29 23:23 ` [U-Boot] [PATCH v3 2/2] rockchip: Add support for MiQi rk3288 board Jernej Skrabec
0 siblings, 2 replies; 11+ messages in thread
From: Jernej Skrabec @ 2017-03-29 23:23 UTC (permalink / raw)
To: u-boot
This series adds support for MiQi board.
MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
expansion ports.
Patch 1 first sorts all rk3288 boards alphabeticaly.
Patch 2 adds support for MiQi board
Jernej Skrabec (2):
rockchip: cosmetic: Sort RK3288 boards
rockchip: Add support for MiQi rk3288 board
arch/arm/dts/Makefile | 11 +-
arch/arm/dts/rk3288-miqi.dts | 46 ++++
arch/arm/dts/rk3288-miqi.dtsi | 423 ++++++++++++++++++++++++++++++++
arch/arm/mach-rockchip/rk3288/Kconfig | 101 ++++----
board/mqmaker/miqi_rk3288/Kconfig | 15 ++
board/mqmaker/miqi_rk3288/MAINTAINERS | 6 +
board/mqmaker/miqi_rk3288/Makefile | 7 +
board/mqmaker/miqi_rk3288/miqi-rk3288.c | 15 ++
configs/miqi-rk3288_defconfig | 73 ++++++
doc/README.rockchip | 5 +-
include/configs/miqi_rk3288.h | 22 ++
11 files changed, 672 insertions(+), 52 deletions(-)
create mode 100644 arch/arm/dts/rk3288-miqi.dts
create mode 100644 arch/arm/dts/rk3288-miqi.dtsi
create mode 100644 board/mqmaker/miqi_rk3288/Kconfig
create mode 100644 board/mqmaker/miqi_rk3288/MAINTAINERS
create mode 100644 board/mqmaker/miqi_rk3288/Makefile
create mode 100644 board/mqmaker/miqi_rk3288/miqi-rk3288.c
create mode 100644 configs/miqi-rk3288_defconfig
create mode 100644 include/configs/miqi_rk3288.h
--
2.12.1
^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v3 1/2] rockchip: cosmetic: Sort RK3288 boards
2017-03-29 23:23 [U-Boot] [PATCH v3 0/2] rockchip: Add support for MiQi board Jernej Skrabec
@ 2017-03-29 23:23 ` Jernej Skrabec
2017-03-30 3:24 ` Kever Yang
` (2 more replies)
2017-03-29 23:23 ` [U-Boot] [PATCH v3 2/2] rockchip: Add support for MiQi rk3288 board Jernej Skrabec
1 sibling, 3 replies; 11+ messages in thread
From: Jernej Skrabec @ 2017-03-29 23:23 UTC (permalink / raw)
To: u-boot
Sort rk3288 boards in alphabetical order.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
---
Changes in v3:
- new patch
arch/arm/dts/Makefile | 10 ++--
arch/arm/mach-rockchip/rk3288/Kconfig | 90 +++++++++++++++++------------------
doc/README.rockchip | 2 +-
3 files changed, 51 insertions(+), 51 deletions(-)
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index afeb43ff66..3d9a80a603 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -29,15 +29,15 @@ dtb-$(CONFIG_EXYNOS5) += exynos5250-arndale.dtb \
dtb-$(CONFIG_EXYNOS7420) += exynos7420-espresso7420.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3036-sdk.dtb \
+ rk3288-evb.dtb \
+ rk3288-fennec.dtb \
rk3288-firefly.dtb \
+ rk3288-popmetal.dtb \
+ rk3288-rock2-square.dtb \
+ rk3288-tinker.dtb \
rk3288-veyron-jerry.dtb \
rk3288-veyron-mickey.dtb \
rk3288-veyron-minnie.dtb \
- rk3288-rock2-square.dtb \
- rk3288-evb.dtb \
- rk3288-fennec.dtb \
- rk3288-tinker.dtb \
- rk3288-popmetal.dtb \
rk3328-evb.dtb \
rk3399-evb.dtb
dtb-$(CONFIG_ARCH_MESON) += \
diff --git a/arch/arm/mach-rockchip/rk3288/Kconfig b/arch/arm/mach-rockchip/rk3288/Kconfig
index 738a20d07c..13f7513813 100644
--- a/arch/arm/mach-rockchip/rk3288/Kconfig
+++ b/arch/arm/mach-rockchip/rk3288/Kconfig
@@ -1,13 +1,34 @@
if ROCKCHIP_RK3288
-config TARGET_FIREFLY_RK3288
- bool "Firefly-RK3288"
+config TARGET_CHROMEBOOK_JERRY
+ bool "Google/Rockchip Veyron-Jerry Chromebook"
select BOARD_LATE_INIT
help
- Firefly is a RK3288-based development board with 2 USB ports,
- HDMI, VGA, micro-SD card, audio, WiFi and Gigabit Ethernet, It
- also includes on-board eMMC and 1GB of SDRAM. Expansion connectors
- provide access to display pins, I2C, SPI, UART and GPIOs.
+ Jerry is a RK3288-based clamshell device with 2 USB 3.0 ports,
+ HDMI, an 11.9 inch EDP display, micro-SD card, touchpad and
+ WiFi. It includes a Chrome OS EC (Cortex-M3) to provide access to
+ the keyboard and battery functions.
+
+config TARGET_CHROMEBIT_MICKEY
+ bool "Google/Rockchip Veyron-Mickey Chromebit"
+ select BOARD_LATE_INIT
+ help
+ Mickey is a small RK3288-based device with one USB 3.0 port, HDMI
+ and WiFi. It has a separate power port and is designed to connect
+ to the HDMI input of a monitor or TV. It has no internal battery.
+ Typically a USB hub or wireless keyboard/touchpad is used to get
+ keyboard and mouse access.
+
+config TARGET_CHROMEBOOK_MINNIE
+ bool "Google/Rockchip Veyron-Minnie Chromebook"
+ select BOARD_LATE_INIT
+ help
+ Minnie is a RK3288-based convertible clamshell device with 2 USB 3.0
+ ports, micro HDMI, a 10.1-inch 1280x800 EDP display, micro-SD card,
+ HD camera, touchpad, WiFi and Bluetooth. It includes a Chrome OS
+ EC (Cortex-M3) to provide access to the keyboard and battery
+ functions. It includes 2 or 4GB of SDRAM and 16 or 32GB of
+ internal MMC. The product name is ASUS Chromebook Flip.
config TARGET_EVB_RK3288
bool "Evb-RK3288"
@@ -27,6 +48,15 @@ config TARGET_FENNEC_RK3288
includes on-board eMMC and 2GB of SDRAM. Expansion connectors
provide access to display pins, I2C, SPI, UART and GPIOs.
+config TARGET_FIREFLY_RK3288
+ bool "Firefly-RK3288"
+ select BOARD_LATE_INIT
+ help
+ Firefly is a RK3288-based development board with 2 USB ports,
+ HDMI, VGA, micro-SD card, audio, WiFi and Gigabit Ethernet, It
+ also includes on-board eMMC and 1GB of SDRAM. Expansion connectors
+ provide access to display pins, I2C, SPI, UART and GPIOs.
+
config TARGET_POPMETAL_RK3288
bool "PopMetal-RK3288"
select BOARD_LATE_INIT
@@ -37,45 +67,6 @@ config TARGET_POPMETAL_RK3288
2GB DDR3. Expansion connectors provide access to I2C, SPI, UART,
GPIOs and display interface.
-config TARGET_TINKER_RK3288
- bool "Tinker-RK3288"
- select BOARD_LATE_INIT
- help
- Tinker is a RK3288-based development board with 2 USB ports, HDMI,
- micro-SD card, audio, Gigabit Ethernet. It also includes on-board
- 8GB eMMC and 2GB of SDRAM. Expansion connectors provide access to
- I2C, SPI, UART, GPIOs.
-
-config TARGET_CHROMEBOOK_JERRY
- bool "Google/Rockchip Veyron-Jerry Chromebook"
- select BOARD_LATE_INIT
- help
- Jerry is a RK3288-based clamshell device with 2 USB 3.0 ports,
- HDMI, an 11.9 inch EDP display, micro-SD card, touchpad and
- WiFi. It includes a Chrome OS EC (Cortex-M3) to provide access to
- the keyboard and battery functions.
-
-config TARGET_CHROMEBIT_MICKEY
- bool "Google/Rockchip Veyron-Mickey Chromebit"
- select BOARD_LATE_INIT
- help
- Mickey is a small RK3288-based device with one USB 3.0 port, HDMI
- and WiFi. It has a separate power port and is designed to connect
- to the HDMI input of a monitor or TV. It has no internal battery.
- Typically a USB hub or wireless keyboard/touchpad is used to get
- keyboard and mouse access.
-
-config TARGET_CHROMEBOOK_MINNIE
- bool "Google/Rockchip Veyron-Minnie Chromebook"
- select BOARD_LATE_INIT
- help
- Minnie is a RK3288-based convertible clamshell device with 2 USB 3.0
- ports, micro HDMI, a 10.1-inch 1280x800 EDP display, micro-SD card,
- HD camera, touchpad, WiFi and Bluetooth. It includes a Chrome OS
- EC (Cortex-M3) to provide access to the keyboard and battery
- functions. It includes 2 or 4GB of SDRAM and 16 or 32GB of
- internal MMC. The product name is ASUS Chromebook Flip.
-
config TARGET_ROCK2
bool "Radxa Rock 2"
select BOARD_LATE_INIT
@@ -85,6 +76,15 @@ config TARGET_ROCK2
space for a real-time-clock battery. There is also an expansion
interface which provides access to many pins.
+config TARGET_TINKER_RK3288
+ bool "Tinker-RK3288"
+ select BOARD_LATE_INIT
+ help
+ Tinker is a RK3288-based development board with 2 USB ports, HDMI,
+ micro-SD card, audio, Gigabit Ethernet. It also includes on-board
+ 8GB eMMC and 2GB of SDRAM. Expansion connectors provide access to
+ I2C, SPI, UART, GPIOs.
+
config ROCKCHIP_FAST_SPL
bool "Change the CPU to full speed in SPL"
depends on TARGET_CHROMEBOOK_JERRY
diff --git a/doc/README.rockchip b/doc/README.rockchip
index 186a1a007e..a408522346 100644
--- a/doc/README.rockchip
+++ b/doc/README.rockchip
@@ -42,9 +42,9 @@ At present seven RK3288 boards are supported:
- Fennec RK3288 - use fennec-rk3288 configuration
- Firefly RK3288 - use firefly-rk3288 configuration
- Hisense Chromebook - use chromebook_jerry configuration
- - Tinker RK3288 - use tinker-rk3288 configuration
- PopMetal RK3288 - use popmetal-rk3288 configuration
- Radxa Rock 2 - use rock2 configuration
+ - Tinker RK3288 - use tinker-rk3288 configuration
Two RK3036 board are supported:
--
2.12.1
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v3 2/2] rockchip: Add support for MiQi rk3288 board
2017-03-29 23:23 [U-Boot] [PATCH v3 0/2] rockchip: Add support for MiQi board Jernej Skrabec
2017-03-29 23:23 ` [U-Boot] [PATCH v3 1/2] rockchip: cosmetic: Sort RK3288 boards Jernej Skrabec
@ 2017-03-29 23:23 ` Jernej Skrabec
2017-03-30 3:25 ` Kever Yang
` (2 more replies)
1 sibling, 3 replies; 11+ messages in thread
From: Jernej Skrabec @ 2017-03-29 23:23 UTC (permalink / raw)
To: u-boot
MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
expansion ports.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
---
Changes in v3:
- split out cosmetic changes into a new patch
Changes in v2:
- change license to SPDX identifier
- reorder boards in alphabetical order in Kconfig and Makefile
arch/arm/dts/Makefile | 1 +
arch/arm/dts/rk3288-miqi.dts | 46 ++++
arch/arm/dts/rk3288-miqi.dtsi | 423 ++++++++++++++++++++++++++++++++
arch/arm/mach-rockchip/rk3288/Kconfig | 11 +
board/mqmaker/miqi_rk3288/Kconfig | 15 ++
board/mqmaker/miqi_rk3288/MAINTAINERS | 6 +
board/mqmaker/miqi_rk3288/Makefile | 7 +
board/mqmaker/miqi_rk3288/miqi-rk3288.c | 15 ++
configs/miqi-rk3288_defconfig | 73 ++++++
doc/README.rockchip | 3 +-
include/configs/miqi_rk3288.h | 22 ++
11 files changed, 621 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/dts/rk3288-miqi.dts
create mode 100644 arch/arm/dts/rk3288-miqi.dtsi
create mode 100644 board/mqmaker/miqi_rk3288/Kconfig
create mode 100644 board/mqmaker/miqi_rk3288/MAINTAINERS
create mode 100644 board/mqmaker/miqi_rk3288/Makefile
create mode 100644 board/mqmaker/miqi_rk3288/miqi-rk3288.c
create mode 100644 configs/miqi-rk3288_defconfig
create mode 100644 include/configs/miqi_rk3288.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 3d9a80a603..9e95386ca5 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -32,6 +32,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3288-evb.dtb \
rk3288-fennec.dtb \
rk3288-firefly.dtb \
+ rk3288-miqi.dtb \
rk3288-popmetal.dtb \
rk3288-rock2-square.dtb \
rk3288-tinker.dtb \
diff --git a/arch/arm/dts/rk3288-miqi.dts b/arch/arm/dts/rk3288-miqi.dts
new file mode 100644
index 0000000000..7b92caf024
--- /dev/null
+++ b/arch/arm/dts/rk3288-miqi.dts
@@ -0,0 +1,46 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+ X11
+ */
+
+/dts-v1/;
+#include "rk3288-miqi.dtsi"
+
+/ {
+ model = "mqmaker MiQi";
+ compatible = "mqmaker,miqi", "rockchip,rk3288";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+};
+
+&dmc {
+ rockchip,pctl-timing = <0x29a 0xc8 0x1f8 0x42 0x4e 0x4 0xea 0xa
+ 0x5 0x0 0xa 0x7 0x19 0x24 0xa 0x7
+ 0x5 0xa 0x5 0x200 0x5 0x10 0x40 0x0
+ 0x1 0x7 0x7 0x4 0xc 0x43 0x100 0x0
+ 0x5 0x0>;
+ rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200
+ 0xa60 0x40 0x10 0x0>;
+ rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 9 1>;
+};
+
+
+&pinctrl {
+ u-boot,dm-pre-reloc;
+};
+
+&uart2 {
+ u-boot,dm-pre-reloc;
+ reg-shift = <2>;
+};
+
+&sdmmc {
+ u-boot,dm-pre-reloc;
+};
+
+&emmc {
+ u-boot,dm-pre-reloc;
+};
diff --git a/arch/arm/dts/rk3288-miqi.dtsi b/arch/arm/dts/rk3288-miqi.dtsi
new file mode 100644
index 0000000000..47dc0f9d74
--- /dev/null
+++ b/arch/arm/dts/rk3288-miqi.dtsi
@@ -0,0 +1,423 @@
+/*
+ * Copyright (c) 2016 Heiko Stuebner <heiko@sntech.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+ X11
+ */
+
+#include "rk3288.dtsi"
+
+/ {
+ memory {
+ device_type = "memory";
+ reg = <0 0x80000000>;
+ };
+
+ ext_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ };
+
+ io_domains: io-domains {
+ compatible = "rockchip,rk3288-io-voltage-domain";
+ rockchip,grf = <&grf>;
+
+ audio-supply = <&vcca_33>;
+ flash0-supply = <&vcc_flash>;
+ flash1-supply = <&vcc_lan>;
+ gpio30-supply = <&vcc_io>;
+ gpio1830-supply = <&vcc_io>;
+ lcdc-supply = <&vcc_io>;
+ sdcard-supply = <&vccio_sd>;
+ wifi-supply = <&vcc_18>;
+ };
+
+
+ leds {
+ u-boot,dm-pre-reloc;
+ compatible = "gpio-leds";
+
+ work {
+ u-boot,dm-pre-reloc;
+ gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
+ label = "miqi:green:user";
+ linux,default-trigger = "default-on";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_ctl>;
+ };
+ };
+
+ vcc_flash: flash-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_flash";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_host: usb-host-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vcc_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_sd: sdmmc-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_pwr>;
+ regulator-name = "vcc_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_sys: vsys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&cpu0 {
+ cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ disable-wp;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>;
+ vmmc-supply = <&vcc_io>;
+ vqmmc-supply = <&vcc_flash>;
+ status = "okay";
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ clock_in_out = "input";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>;
+ phy-supply = <&vcc_lan>;
+ phy-mode = "rgmii";
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c5>;
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ vdd_cpu: syr827 at 40 {
+ compatible = "silergy,syr827";
+ fcs,suspend-voltage-selector = <1>;
+ reg = <0x40>;
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-enable-ramp-delay = <300>;
+ regulator-ramp-delay = <8000>;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vdd_gpu: syr828 at 41 {
+ compatible = "silergy,syr828";
+ fcs,suspend-voltage-selector = <1>;
+ reg = <0x41>;
+ regulator-name = "vdd_gpu";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ hym8563: hym8563 at 51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ };
+
+ act8846: act8846 at 5a {
+ compatible = "active-semi,act8846";
+ reg = <0x5a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_vsel>;
+ system-power-controller;
+
+ vp1-supply = <&vcc_sys>;
+ vp2-supply = <&vcc_sys>;
+ vp3-supply = <&vcc_sys>;
+ vp4-supply = <&vcc_sys>;
+ inl1-supply = <&vcc_sys>;
+ inl2-supply = <&vcc_sys>;
+ inl3-supply = <&vcc_20>;
+
+ regulators {
+ vcc_ddr: REG1 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ };
+
+ vcc_io: REG2 {
+ regulator-name = "vcc_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdd_log: REG3 {
+ regulator-name = "vdd_log";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ vcc_20: REG4 {
+ regulator-name = "vcc_20";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ vccio_sd: REG5 {
+ regulator-name = "vccio_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdd10_lcd: REG6 {
+ regulator-name = "vdd10_lcd";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ vcca_18: REG7 {
+ regulator-name = "vcca_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vcca_33: REG8 {
+ regulator-name = "vcca_33";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_lan: REG9 {
+ regulator-name = "vcc_lan";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vdd_10: REG10 {
+ regulator-name = "vdd_10";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ vcc_18: REG11 {
+ regulator-name = "vcc_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vcc18_lcd: REG12 {
+ regulator-name = "vcc18_lcd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&pinctrl {
+ pcfg_output_high: pcfg-output-high {
+ output-high;
+ };
+
+ pcfg_output_low: pcfg-output-low {
+ output-low;
+ };
+
+ pcfg_pull_up_drv_12ma: pcfg-pull-up-drv-12ma {
+ bias-pull-up;
+ drive-strength = <12>;
+ };
+
+ act8846 {
+ pmic_int: pmic-int {
+ rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ pmic_sleep: pmic-sleep {
+ rockchip,pins = <0 0 RK_FUNC_GPIO &pcfg_output_low>;
+ };
+
+ pmic_vsel: pmic-vsel {
+ rockchip,pins = <7 1 RK_FUNC_GPIO &pcfg_output_low>;
+ };
+ };
+
+ gmac {
+ phy_int: phy-int {
+ rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ phy_pmeb: phy-pmeb {
+ rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ phy_rst: phy-rst {
+ rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+ };
+
+ leds {
+ led_ctl: led-ctl {
+ rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdmmc {
+ /*
+ * Default drive strength isn't enough to achieve even
+ * high-speed mode on firefly board so bump up to 12ma.
+ */
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 17 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 18 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 19 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+ };
+
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_12ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+ };
+
+ sdmmc_pwr: sdmmc-pwr {
+ rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb_host {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&saradc {
+ vref-supply = <&vcc_18>;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ disable-wp;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <0>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&usb_host1 {
+ vbus-supply = <&vcc_host>;
+ status = "okay";
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
diff --git a/arch/arm/mach-rockchip/rk3288/Kconfig b/arch/arm/mach-rockchip/rk3288/Kconfig
index 13f7513813..8e7355ece4 100644
--- a/arch/arm/mach-rockchip/rk3288/Kconfig
+++ b/arch/arm/mach-rockchip/rk3288/Kconfig
@@ -57,6 +57,15 @@ config TARGET_FIREFLY_RK3288
also includes on-board eMMC and 1GB of SDRAM. Expansion connectors
provide access to display pins, I2C, SPI, UART and GPIOs.
+config TARGET_MIQI_RK3288
+ bool "MiQi-RK3288"
+ select BOARD_LATE_INIT
+ help
+ MiQi-RK3288 is a RK3288-based development board with 4 USB 2.0
+ ports, HDMI, micro-SD card, 16 GB eMMC and Gigabit Ethernet. It
+ has 1 or 2 GiB SDRAM. Expansion connectors provide access to
+ I2C, SPI, UART, GPIOs and fan control.
+
config TARGET_POPMETAL_RK3288
bool "PopMetal-RK3288"
select BOARD_LATE_INIT
@@ -118,6 +127,8 @@ source "board/firefly/firefly-rk3288/Kconfig"
source "board/google/veyron/Kconfig"
+source "board/mqmaker/miqi_rk3288/Kconfig"
+
source "board/radxa/rock2/Kconfig"
source "board/rockchip/evb_rk3288/Kconfig"
diff --git a/board/mqmaker/miqi_rk3288/Kconfig b/board/mqmaker/miqi_rk3288/Kconfig
new file mode 100644
index 0000000000..232a112090
--- /dev/null
+++ b/board/mqmaker/miqi_rk3288/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_MIQI_RK3288
+
+config SYS_BOARD
+ default "miqi_rk3288"
+
+config SYS_VENDOR
+ default "mqmaker"
+
+config SYS_CONFIG_NAME
+ default "miqi_rk3288"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+ def_bool y
+
+endif
diff --git a/board/mqmaker/miqi_rk3288/MAINTAINERS b/board/mqmaker/miqi_rk3288/MAINTAINERS
new file mode 100644
index 0000000000..053a5e6028
--- /dev/null
+++ b/board/mqmaker/miqi_rk3288/MAINTAINERS
@@ -0,0 +1,6 @@
+MIQI
+M: Jernej Skrabec <jernej.skrabec@siol.net>
+S: Maintained
+F: board/mqmaker/miqi_rk3288
+F: include/configs/miqi_rk3288.h
+F: configs/miqi-rk3288_defconfig
diff --git a/board/mqmaker/miqi_rk3288/Makefile b/board/mqmaker/miqi_rk3288/Makefile
new file mode 100644
index 0000000000..ec95affb39
--- /dev/null
+++ b/board/mqmaker/miqi_rk3288/Makefile
@@ -0,0 +1,7 @@
+#
+# (C) Copyright 2016 Rockchip Electronics Co., Ltd
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += miqi-rk3288.o
diff --git a/board/mqmaker/miqi_rk3288/miqi-rk3288.c b/board/mqmaker/miqi_rk3288/miqi-rk3288.c
new file mode 100644
index 0000000000..a82f0ae283
--- /dev/null
+++ b/board/mqmaker/miqi_rk3288/miqi-rk3288.c
@@ -0,0 +1,15 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+
+void board_boot_order(u32 *spl_boot_list)
+{
+ /* eMMC prior to sdcard. */
+ spl_boot_list[0] = BOOT_DEVICE_MMC2;
+ spl_boot_list[1] = BOOT_DEVICE_MMC1;
+}
diff --git a/configs/miqi-rk3288_defconfig b/configs/miqi-rk3288_defconfig
new file mode 100644
index 0000000000..203824b893
--- /dev/null
+++ b/configs/miqi-rk3288_defconfig
@@ -0,0 +1,73 @@
+CONFIG_ARM=y
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_ROCKCHIP_RK3288=y
+CONFIG_ROCKCHIP_SPL_BACK_TO_BROM=y
+CONFIG_TARGET_MIQI_RK3288=y
+CONFIG_SPL_STACK_R_ADDR=0x80000
+CONFIG_DEFAULT_DEVICE_TREE="rk3288-miqi"
+CONFIG_SILENT_CONSOLE=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x2000
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_ISO_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_SPL_PARTITION_UUIDS=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SPL_SYSCON=y
+# CONFIG_SPL_SIMPLE_BUS is not set
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+# CONFIG_SPL_PINCTRL_FULL is not set
+CONFIG_ROCKCHIP_RK3288_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_ACT8846=y
+CONFIG_REGULATOR_ACT8846=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_RAM=y
+CONFIG_SPL_RAM=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_BASE=0xff690000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550=y
+CONFIG_ROCKCHIP_SERIAL=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_DM_VIDEO=y
+CONFIG_DISPLAY=y
+CONFIG_VIDEO_ROCKCHIP=y
+CONFIG_CONSOLE_SCROLL_LINES=10
+CONFIG_USE_TINY_PRINTF=y
+CONFIG_CMD_DHRYSTONE=y
+CONFIG_ERRNO_STR=y
diff --git a/doc/README.rockchip b/doc/README.rockchip
index a408522346..cdeab2d961 100644
--- a/doc/README.rockchip
+++ b/doc/README.rockchip
@@ -36,12 +36,13 @@ You will need:
Building
========
-At present seven RK3288 boards are supported:
+At present eight RK3288 boards are supported:
- EVB RK3288 - use evb-rk3288 configuration
- Fennec RK3288 - use fennec-rk3288 configuration
- Firefly RK3288 - use firefly-rk3288 configuration
- Hisense Chromebook - use chromebook_jerry configuration
+ - MiQi RK3288 - use miqi-rk3288 configuration
- PopMetal RK3288 - use popmetal-rk3288 configuration
- Radxa Rock 2 - use rock2 configuration
- Tinker RK3288 - use tinker-rk3288 configuration
diff --git a/include/configs/miqi_rk3288.h b/include/configs/miqi_rk3288.h
new file mode 100644
index 0000000000..f686042499
--- /dev/null
+++ b/include/configs/miqi_rk3288.h
@@ -0,0 +1,22 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define ROCKCHIP_DEVICE_SETTINGS \
+ "stdin=serial,cros-ec-keyb\0" \
+ "stdout=serial,vidconsole\0" \
+ "stderr=serial,vidconsole\0"
+
+#include <configs/rk3288_common.h>
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_SYS_WHITE_ON_BLACK
+
+#endif
--
2.12.1
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v3 1/2] rockchip: cosmetic: Sort RK3288 boards
2017-03-29 23:23 ` [U-Boot] [PATCH v3 1/2] rockchip: cosmetic: Sort RK3288 boards Jernej Skrabec
@ 2017-03-30 3:24 ` Kever Yang
2017-03-30 7:04 ` Eddie Cai
2017-04-01 4:23 ` Simon Glass
2 siblings, 0 replies; 11+ messages in thread
From: Kever Yang @ 2017-03-30 3:24 UTC (permalink / raw)
To: u-boot
Hi Jernej,
On 03/30/2017 07:23 AM, Jernej Skrabec wrote:
> Sort rk3288 boards in alphabetical order.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
> ---
> Changes in v3:
> - new patch
>
> arch/arm/dts/Makefile | 10 ++--
> arch/arm/mach-rockchip/rk3288/Kconfig | 90 +++++++++++++++++------------------
> doc/README.rockchip | 2 +-
> 3 files changed, 51 insertions(+), 51 deletions(-)
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index afeb43ff66..3d9a80a603 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -29,15 +29,15 @@ dtb-$(CONFIG_EXYNOS5) += exynos5250-arndale.dtb \
> dtb-$(CONFIG_EXYNOS7420) += exynos7420-espresso7420.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += \
> rk3036-sdk.dtb \
> + rk3288-evb.dtb \
> + rk3288-fennec.dtb \
> rk3288-firefly.dtb \
> + rk3288-popmetal.dtb \
> + rk3288-rock2-square.dtb \
> + rk3288-tinker.dtb \
> rk3288-veyron-jerry.dtb \
> rk3288-veyron-mickey.dtb \
> rk3288-veyron-minnie.dtb \
> - rk3288-rock2-square.dtb \
> - rk3288-evb.dtb \
> - rk3288-fennec.dtb \
> - rk3288-tinker.dtb \
> - rk3288-popmetal.dtb \
> rk3328-evb.dtb \
> rk3399-evb.dtb
> dtb-$(CONFIG_ARCH_MESON) += \
> diff --git a/arch/arm/mach-rockchip/rk3288/Kconfig b/arch/arm/mach-rockchip/rk3288/Kconfig
> index 738a20d07c..13f7513813 100644
> --- a/arch/arm/mach-rockchip/rk3288/Kconfig
> +++ b/arch/arm/mach-rockchip/rk3288/Kconfig
> @@ -1,13 +1,34 @@
> if ROCKCHIP_RK3288
>
> -config TARGET_FIREFLY_RK3288
> - bool "Firefly-RK3288"
> +config TARGET_CHROMEBOOK_JERRY
> + bool "Google/Rockchip Veyron-Jerry Chromebook"
> select BOARD_LATE_INIT
> help
> - Firefly is a RK3288-based development board with 2 USB ports,
> - HDMI, VGA, micro-SD card, audio, WiFi and Gigabit Ethernet, It
> - also includes on-board eMMC and 1GB of SDRAM. Expansion connectors
> - provide access to display pins, I2C, SPI, UART and GPIOs.
> + Jerry is a RK3288-based clamshell device with 2 USB 3.0 ports,
> + HDMI, an 11.9 inch EDP display, micro-SD card, touchpad and
> + WiFi. It includes a Chrome OS EC (Cortex-M3) to provide access to
> + the keyboard and battery functions.
> +
> +config TARGET_CHROMEBIT_MICKEY
> + bool "Google/Rockchip Veyron-Mickey Chromebit"
> + select BOARD_LATE_INIT
> + help
> + Mickey is a small RK3288-based device with one USB 3.0 port, HDMI
> + and WiFi. It has a separate power port and is designed to connect
> + to the HDMI input of a monitor or TV. It has no internal battery.
> + Typically a USB hub or wireless keyboard/touchpad is used to get
> + keyboard and mouse access.
> +
> +config TARGET_CHROMEBOOK_MINNIE
> + bool "Google/Rockchip Veyron-Minnie Chromebook"
> + select BOARD_LATE_INIT
> + help
> + Minnie is a RK3288-based convertible clamshell device with 2 USB 3.0
> + ports, micro HDMI, a 10.1-inch 1280x800 EDP display, micro-SD card,
> + HD camera, touchpad, WiFi and Bluetooth. It includes a Chrome OS
> + EC (Cortex-M3) to provide access to the keyboard and battery
> + functions. It includes 2 or 4GB of SDRAM and 16 or 32GB of
> + internal MMC. The product name is ASUS Chromebook Flip.
>
> config TARGET_EVB_RK3288
> bool "Evb-RK3288"
> @@ -27,6 +48,15 @@ config TARGET_FENNEC_RK3288
> includes on-board eMMC and 2GB of SDRAM. Expansion connectors
> provide access to display pins, I2C, SPI, UART and GPIOs.
>
> +config TARGET_FIREFLY_RK3288
> + bool "Firefly-RK3288"
> + select BOARD_LATE_INIT
> + help
> + Firefly is a RK3288-based development board with 2 USB ports,
> + HDMI, VGA, micro-SD card, audio, WiFi and Gigabit Ethernet, It
> + also includes on-board eMMC and 1GB of SDRAM. Expansion connectors
> + provide access to display pins, I2C, SPI, UART and GPIOs.
> +
> config TARGET_POPMETAL_RK3288
> bool "PopMetal-RK3288"
> select BOARD_LATE_INIT
> @@ -37,45 +67,6 @@ config TARGET_POPMETAL_RK3288
> 2GB DDR3. Expansion connectors provide access to I2C, SPI, UART,
> GPIOs and display interface.
>
> -config TARGET_TINKER_RK3288
> - bool "Tinker-RK3288"
> - select BOARD_LATE_INIT
> - help
> - Tinker is a RK3288-based development board with 2 USB ports, HDMI,
> - micro-SD card, audio, Gigabit Ethernet. It also includes on-board
> - 8GB eMMC and 2GB of SDRAM. Expansion connectors provide access to
> - I2C, SPI, UART, GPIOs.
> -
> -config TARGET_CHROMEBOOK_JERRY
> - bool "Google/Rockchip Veyron-Jerry Chromebook"
> - select BOARD_LATE_INIT
> - help
> - Jerry is a RK3288-based clamshell device with 2 USB 3.0 ports,
> - HDMI, an 11.9 inch EDP display, micro-SD card, touchpad and
> - WiFi. It includes a Chrome OS EC (Cortex-M3) to provide access to
> - the keyboard and battery functions.
> -
> -config TARGET_CHROMEBIT_MICKEY
> - bool "Google/Rockchip Veyron-Mickey Chromebit"
> - select BOARD_LATE_INIT
> - help
> - Mickey is a small RK3288-based device with one USB 3.0 port, HDMI
> - and WiFi. It has a separate power port and is designed to connect
> - to the HDMI input of a monitor or TV. It has no internal battery.
> - Typically a USB hub or wireless keyboard/touchpad is used to get
> - keyboard and mouse access.
> -
> -config TARGET_CHROMEBOOK_MINNIE
> - bool "Google/Rockchip Veyron-Minnie Chromebook"
> - select BOARD_LATE_INIT
> - help
> - Minnie is a RK3288-based convertible clamshell device with 2 USB 3.0
> - ports, micro HDMI, a 10.1-inch 1280x800 EDP display, micro-SD card,
> - HD camera, touchpad, WiFi and Bluetooth. It includes a Chrome OS
> - EC (Cortex-M3) to provide access to the keyboard and battery
> - functions. It includes 2 or 4GB of SDRAM and 16 or 32GB of
> - internal MMC. The product name is ASUS Chromebook Flip.
> -
> config TARGET_ROCK2
> bool "Radxa Rock 2"
> select BOARD_LATE_INIT
> @@ -85,6 +76,15 @@ config TARGET_ROCK2
> space for a real-time-clock battery. There is also an expansion
> interface which provides access to many pins.
>
> +config TARGET_TINKER_RK3288
> + bool "Tinker-RK3288"
> + select BOARD_LATE_INIT
> + help
> + Tinker is a RK3288-based development board with 2 USB ports, HDMI,
> + micro-SD card, audio, Gigabit Ethernet. It also includes on-board
> + 8GB eMMC and 2GB of SDRAM. Expansion connectors provide access to
> + I2C, SPI, UART, GPIOs.
> +
> config ROCKCHIP_FAST_SPL
> bool "Change the CPU to full speed in SPL"
> depends on TARGET_CHROMEBOOK_JERRY
> diff --git a/doc/README.rockchip b/doc/README.rockchip
> index 186a1a007e..a408522346 100644
> --- a/doc/README.rockchip
> +++ b/doc/README.rockchip
> @@ -42,9 +42,9 @@ At present seven RK3288 boards are supported:
> - Fennec RK3288 - use fennec-rk3288 configuration
> - Firefly RK3288 - use firefly-rk3288 configuration
> - Hisense Chromebook - use chromebook_jerry configuration
> - - Tinker RK3288 - use tinker-rk3288 configuration
> - PopMetal RK3288 - use popmetal-rk3288 configuration
> - Radxa Rock 2 - use rock2 configuration
> + - Tinker RK3288 - use tinker-rk3288 configuration
>
> Two RK3036 board are supported:
>
Looks good to me,
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Thanks,
- Kever
^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v3 2/2] rockchip: Add support for MiQi rk3288 board
2017-03-29 23:23 ` [U-Boot] [PATCH v3 2/2] rockchip: Add support for MiQi rk3288 board Jernej Skrabec
@ 2017-03-30 3:25 ` Kever Yang
2017-03-30 7:05 ` Eddie Cai
2017-04-01 4:23 ` Simon Glass
2 siblings, 0 replies; 11+ messages in thread
From: Kever Yang @ 2017-03-30 3:25 UTC (permalink / raw)
To: u-boot
Hi Jernej,
On 03/30/2017 07:23 AM, Jernej Skrabec wrote:
> MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
> micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
> expansion ports.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
> ---
> Changes in v3:
> - split out cosmetic changes into a new patch
>
> Changes in v2:
> - change license to SPDX identifier
> - reorder boards in alphabetical order in Kconfig and Makefile
>
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/rk3288-miqi.dts | 46 ++++
> arch/arm/dts/rk3288-miqi.dtsi | 423 ++++++++++++++++++++++++++++++++
> arch/arm/mach-rockchip/rk3288/Kconfig | 11 +
> board/mqmaker/miqi_rk3288/Kconfig | 15 ++
> board/mqmaker/miqi_rk3288/MAINTAINERS | 6 +
> board/mqmaker/miqi_rk3288/Makefile | 7 +
> board/mqmaker/miqi_rk3288/miqi-rk3288.c | 15 ++
> configs/miqi-rk3288_defconfig | 73 ++++++
> doc/README.rockchip | 3 +-
> include/configs/miqi_rk3288.h | 22 ++
> 11 files changed, 621 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/dts/rk3288-miqi.dts
> create mode 100644 arch/arm/dts/rk3288-miqi.dtsi
> create mode 100644 board/mqmaker/miqi_rk3288/Kconfig
> create mode 100644 board/mqmaker/miqi_rk3288/MAINTAINERS
> create mode 100644 board/mqmaker/miqi_rk3288/Makefile
> create mode 100644 board/mqmaker/miqi_rk3288/miqi-rk3288.c
> create mode 100644 configs/miqi-rk3288_defconfig
> create mode 100644 include/configs/miqi_rk3288.h
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 3d9a80a603..9e95386ca5 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -32,6 +32,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
> rk3288-evb.dtb \
> rk3288-fennec.dtb \
> rk3288-firefly.dtb \
> + rk3288-miqi.dtb \
> rk3288-popmetal.dtb \
> rk3288-rock2-square.dtb \
> rk3288-tinker.dtb \
> diff --git a/arch/arm/dts/rk3288-miqi.dts b/arch/arm/dts/rk3288-miqi.dts
> new file mode 100644
> index 0000000000..7b92caf024
> --- /dev/null
> +++ b/arch/arm/dts/rk3288-miqi.dts
> @@ -0,0 +1,46 @@
> +/*
> + * (C) Copyright 2016 Rockchip Electronics Co., Ltd
> + *
> + * SPDX-License-Identifier: GPL-2.0+ X11
> + */
> +
> +/dts-v1/;
> +#include "rk3288-miqi.dtsi"
> +
> +/ {
> + model = "mqmaker MiQi";
> + compatible = "mqmaker,miqi", "rockchip,rk3288";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + };
> +};
> +
> +&dmc {
> + rockchip,pctl-timing = <0x29a 0xc8 0x1f8 0x42 0x4e 0x4 0xea 0xa
> + 0x5 0x0 0xa 0x7 0x19 0x24 0xa 0x7
> + 0x5 0xa 0x5 0x200 0x5 0x10 0x40 0x0
> + 0x1 0x7 0x7 0x4 0xc 0x43 0x100 0x0
> + 0x5 0x0>;
> + rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200
> + 0xa60 0x40 0x10 0x0>;
> + rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 9 1>;
> +};
> +
> +
> +&pinctrl {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&uart2 {
> + u-boot,dm-pre-reloc;
> + reg-shift = <2>;
> +};
> +
> +&sdmmc {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&emmc {
> + u-boot,dm-pre-reloc;
> +};
> diff --git a/arch/arm/dts/rk3288-miqi.dtsi b/arch/arm/dts/rk3288-miqi.dtsi
> new file mode 100644
> index 0000000000..47dc0f9d74
> --- /dev/null
> +++ b/arch/arm/dts/rk3288-miqi.dtsi
> @@ -0,0 +1,423 @@
> +/*
> + * Copyright (c) 2016 Heiko Stuebner <heiko@sntech.de>
> + *
> + * SPDX-License-Identifier: GPL-2.0+ X11
> + */
> +
> +#include "rk3288.dtsi"
> +
> +/ {
> + memory {
> + device_type = "memory";
> + reg = <0 0x80000000>;
> + };
> +
> + ext_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <125000000>;
> + clock-output-names = "ext_gmac";
> + };
> +
> + io_domains: io-domains {
> + compatible = "rockchip,rk3288-io-voltage-domain";
> + rockchip,grf = <&grf>;
> +
> + audio-supply = <&vcca_33>;
> + flash0-supply = <&vcc_flash>;
> + flash1-supply = <&vcc_lan>;
> + gpio30-supply = <&vcc_io>;
> + gpio1830-supply = <&vcc_io>;
> + lcdc-supply = <&vcc_io>;
> + sdcard-supply = <&vccio_sd>;
> + wifi-supply = <&vcc_18>;
> + };
> +
> +
> + leds {
> + u-boot,dm-pre-reloc;
> + compatible = "gpio-leds";
> +
> + work {
> + u-boot,dm-pre-reloc;
> + gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
> + label = "miqi:green:user";
> + linux,default-trigger = "default-on";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_ctl>;
> + };
> + };
> +
> + vcc_flash: flash-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_flash";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_host: usb-host-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&host_vbus_drv>;
> + regulator-name = "vcc_host";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcc_sd: sdmmc-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_pwr>;
> + regulator-name = "vcc_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <100000>;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_sys: vsys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +};
> +
> +&cpu0 {
> + cpu0-supply = <&vdd_cpu>;
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + disable-wp;
> + non-removable;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>;
> + vmmc-supply = <&vcc_io>;
> + vqmmc-supply = <&vcc_flash>;
> + status = "okay";
> +};
> +
> +&gmac {
> + assigned-clocks = <&cru SCLK_MAC>;
> + assigned-clock-parents = <&ext_gmac>;
> + clock_in_out = "input";
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>;
> + phy-supply = <&vcc_lan>;
> + phy-mode = "rgmii";
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 1000000>;
> + snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
> + tx_delay = <0x30>;
> + rx_delay = <0x10>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + ddc-i2c-bus = <&i2c5>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + vdd_cpu: syr827 at 40 {
> + compatible = "silergy,syr827";
> + fcs,suspend-voltage-selector = <1>;
> + reg = <0x40>;
> + regulator-name = "vdd_cpu";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-enable-ramp-delay = <300>;
> + regulator-ramp-delay = <8000>;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vdd_gpu: syr828 at 41 {
> + compatible = "silergy,syr828";
> + fcs,suspend-voltage-selector = <1>;
> + reg = <0x41>;
> + regulator-name = "vdd_gpu";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + hym8563: hym8563 at 51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "xin32k";
> + };
> +
> + act8846: act8846 at 5a {
> + compatible = "active-semi,act8846";
> + reg = <0x5a>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_vsel>;
> + system-power-controller;
> +
> + vp1-supply = <&vcc_sys>;
> + vp2-supply = <&vcc_sys>;
> + vp3-supply = <&vcc_sys>;
> + vp4-supply = <&vcc_sys>;
> + inl1-supply = <&vcc_sys>;
> + inl2-supply = <&vcc_sys>;
> + inl3-supply = <&vcc_20>;
> +
> + regulators {
> + vcc_ddr: REG1 {
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + };
> +
> + vcc_io: REG2 {
> + regulator-name = "vcc_io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vdd_log: REG3 {
> + regulator-name = "vdd_log";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + };
> +
> + vcc_20: REG4 {
> + regulator-name = "vcc_20";
> + regulator-min-microvolt = <2000000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-always-on;
> + };
> +
> + vccio_sd: REG5 {
> + regulator-name = "vccio_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vdd10_lcd: REG6 {
> + regulator-name = "vdd10_lcd";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + };
> +
> + vcca_18: REG7 {
> + regulator-name = "vcca_18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + vcca_33: REG8 {
> + regulator-name = "vcca_33";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vcc_lan: REG9 {
> + regulator-name = "vcc_lan";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vdd_10: REG10 {
> + regulator-name = "vdd_10";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + };
> +
> + vcc_18: REG11 {
> + regulator-name = "vcc_18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vcc18_lcd: REG12 {
> + regulator-name = "vcc18_lcd";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c4 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&pinctrl {
> + pcfg_output_high: pcfg-output-high {
> + output-high;
> + };
> +
> + pcfg_output_low: pcfg-output-low {
> + output-low;
> + };
> +
> + pcfg_pull_up_drv_12ma: pcfg-pull-up-drv-12ma {
> + bias-pull-up;
> + drive-strength = <12>;
> + };
> +
> + act8846 {
> + pmic_int: pmic-int {
> + rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + pmic_sleep: pmic-sleep {
> + rockchip,pins = <0 0 RK_FUNC_GPIO &pcfg_output_low>;
> + };
> +
> + pmic_vsel: pmic-vsel {
> + rockchip,pins = <7 1 RK_FUNC_GPIO &pcfg_output_low>;
> + };
> + };
> +
> + gmac {
> + phy_int: phy-int {
> + rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + phy_pmeb: phy-pmeb {
> + rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + phy_rst: phy-rst {
> + rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>;
> + };
> + };
> +
> + leds {
> + led_ctl: led-ctl {
> + rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdmmc {
> + /*
> + * Default drive strength isn't enough to achieve even
> + * high-speed mode on firefly board so bump up to 12ma.
> + */
> + sdmmc_bus4: sdmmc-bus4 {
> + rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
> + <6 17 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
> + <6 18 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
> + <6 19 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
> + };
> +
> + sdmmc_clk: sdmmc-clk {
> + rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_12ma>;
> + };
> +
> + sdmmc_cmd: sdmmc-cmd {
> + rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
> + };
> +
> + sdmmc_pwr: sdmmc-pwr {
> + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb_host {
> + host_vbus_drv: host-vbus-drv {
> + rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_18>;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + card-detect-delay = <200>;
> + disable-wp;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
> + vmmc-supply = <&vcc_sd>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-mode = <0>;
> + rockchip,hw-tshut-polarity = <0>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&usbphy {
> + status = "okay";
> +};
> +
> +&usb_host1 {
> + vbus-supply = <&vcc_host>;
> + status = "okay";
> +};
> +
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&vopl {
> + status = "okay";
> +};
> +
> +&vopl_mmu {
> + status = "okay";
> +};
> +
> +&wdt {
> + status = "okay";
> +};
> diff --git a/arch/arm/mach-rockchip/rk3288/Kconfig b/arch/arm/mach-rockchip/rk3288/Kconfig
> index 13f7513813..8e7355ece4 100644
> --- a/arch/arm/mach-rockchip/rk3288/Kconfig
> +++ b/arch/arm/mach-rockchip/rk3288/Kconfig
> @@ -57,6 +57,15 @@ config TARGET_FIREFLY_RK3288
> also includes on-board eMMC and 1GB of SDRAM. Expansion connectors
> provide access to display pins, I2C, SPI, UART and GPIOs.
>
> +config TARGET_MIQI_RK3288
> + bool "MiQi-RK3288"
> + select BOARD_LATE_INIT
> + help
> + MiQi-RK3288 is a RK3288-based development board with 4 USB 2.0
> + ports, HDMI, micro-SD card, 16 GB eMMC and Gigabit Ethernet. It
> + has 1 or 2 GiB SDRAM. Expansion connectors provide access to
> + I2C, SPI, UART, GPIOs and fan control.
> +
> config TARGET_POPMETAL_RK3288
> bool "PopMetal-RK3288"
> select BOARD_LATE_INIT
> @@ -118,6 +127,8 @@ source "board/firefly/firefly-rk3288/Kconfig"
>
> source "board/google/veyron/Kconfig"
>
> +source "board/mqmaker/miqi_rk3288/Kconfig"
> +
> source "board/radxa/rock2/Kconfig"
>
> source "board/rockchip/evb_rk3288/Kconfig"
> diff --git a/board/mqmaker/miqi_rk3288/Kconfig b/board/mqmaker/miqi_rk3288/Kconfig
> new file mode 100644
> index 0000000000..232a112090
> --- /dev/null
> +++ b/board/mqmaker/miqi_rk3288/Kconfig
> @@ -0,0 +1,15 @@
> +if TARGET_MIQI_RK3288
> +
> +config SYS_BOARD
> + default "miqi_rk3288"
> +
> +config SYS_VENDOR
> + default "mqmaker"
> +
> +config SYS_CONFIG_NAME
> + default "miqi_rk3288"
> +
> +config BOARD_SPECIFIC_OPTIONS # dummy
> + def_bool y
> +
> +endif
> diff --git a/board/mqmaker/miqi_rk3288/MAINTAINERS b/board/mqmaker/miqi_rk3288/MAINTAINERS
> new file mode 100644
> index 0000000000..053a5e6028
> --- /dev/null
> +++ b/board/mqmaker/miqi_rk3288/MAINTAINERS
> @@ -0,0 +1,6 @@
> +MIQI
> +M: Jernej Skrabec <jernej.skrabec@siol.net>
> +S: Maintained
> +F: board/mqmaker/miqi_rk3288
> +F: include/configs/miqi_rk3288.h
> +F: configs/miqi-rk3288_defconfig
> diff --git a/board/mqmaker/miqi_rk3288/Makefile b/board/mqmaker/miqi_rk3288/Makefile
> new file mode 100644
> index 0000000000..ec95affb39
> --- /dev/null
> +++ b/board/mqmaker/miqi_rk3288/Makefile
> @@ -0,0 +1,7 @@
> +#
> +# (C) Copyright 2016 Rockchip Electronics Co., Ltd
> +#
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +
> +obj-y += miqi-rk3288.o
> diff --git a/board/mqmaker/miqi_rk3288/miqi-rk3288.c b/board/mqmaker/miqi_rk3288/miqi-rk3288.c
> new file mode 100644
> index 0000000000..a82f0ae283
> --- /dev/null
> +++ b/board/mqmaker/miqi_rk3288/miqi-rk3288.c
> @@ -0,0 +1,15 @@
> +/*
> + * (C) Copyright 2016 Rockchip Electronics Co., Ltd
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <spl.h>
> +
> +void board_boot_order(u32 *spl_boot_list)
> +{
> + /* eMMC prior to sdcard. */
> + spl_boot_list[0] = BOOT_DEVICE_MMC2;
> + spl_boot_list[1] = BOOT_DEVICE_MMC1;
> +}
> diff --git a/configs/miqi-rk3288_defconfig b/configs/miqi-rk3288_defconfig
> new file mode 100644
> index 0000000000..203824b893
> --- /dev/null
> +++ b/configs/miqi-rk3288_defconfig
> @@ -0,0 +1,73 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_ROCKCHIP=y
> +CONFIG_SYS_MALLOC_F_LEN=0x2000
> +CONFIG_ROCKCHIP_RK3288=y
> +CONFIG_ROCKCHIP_SPL_BACK_TO_BROM=y
> +CONFIG_TARGET_MIQI_RK3288=y
> +CONFIG_SPL_STACK_R_ADDR=0x80000
> +CONFIG_DEFAULT_DEVICE_TREE="rk3288-miqi"
> +CONFIG_SILENT_CONSOLE=y
> +# CONFIG_DISPLAY_CPUINFO is not set
> +CONFIG_SPL_STACK_R=y
> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x2000
> +# CONFIG_CMD_IMLS is not set
> +CONFIG_CMD_GPT=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_SF=y
> +CONFIG_CMD_SPI=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_GPIO=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_PMIC=y
> +CONFIG_CMD_REGULATOR=y
> +# CONFIG_SPL_DOS_PARTITION is not set
> +# CONFIG_SPL_ISO_PARTITION is not set
> +# CONFIG_SPL_EFI_PARTITION is not set
> +CONFIG_SPL_PARTITION_UUIDS=y
> +CONFIG_SPL_OF_CONTROL=y
> +CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_REGMAP=y
> +CONFIG_SPL_REGMAP=y
> +CONFIG_SYSCON=y
> +CONFIG_SPL_SYSCON=y
> +# CONFIG_SPL_SIMPLE_BUS is not set
> +CONFIG_CLK=y
> +CONFIG_SPL_CLK=y
> +CONFIG_ROCKCHIP_GPIO=y
> +CONFIG_SYS_I2C_ROCKCHIP=y
> +CONFIG_MMC_DW=y
> +CONFIG_MMC_DW_ROCKCHIP=y
> +CONFIG_DM_ETH=y
> +CONFIG_ETH_DESIGNWARE=y
> +CONFIG_GMAC_ROCKCHIP=y
> +CONFIG_PINCTRL=y
> +CONFIG_SPL_PINCTRL=y
> +# CONFIG_SPL_PINCTRL_FULL is not set
> +CONFIG_ROCKCHIP_RK3288_PINCTRL=y
> +CONFIG_DM_PMIC=y
> +CONFIG_PMIC_ACT8846=y
> +CONFIG_REGULATOR_ACT8846=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_PWM_ROCKCHIP=y
> +CONFIG_RAM=y
> +CONFIG_SPL_RAM=y
> +CONFIG_DEBUG_UART=y
> +CONFIG_DEBUG_UART_BASE=0xff690000
> +CONFIG_DEBUG_UART_CLOCK=24000000
> +CONFIG_DEBUG_UART_SHIFT=2
> +CONFIG_SYS_NS16550=y
> +CONFIG_ROCKCHIP_SERIAL=y
> +CONFIG_SYSRESET=y
> +CONFIG_USB=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_DM_VIDEO=y
> +CONFIG_DISPLAY=y
> +CONFIG_VIDEO_ROCKCHIP=y
> +CONFIG_CONSOLE_SCROLL_LINES=10
> +CONFIG_USE_TINY_PRINTF=y
> +CONFIG_CMD_DHRYSTONE=y
> +CONFIG_ERRNO_STR=y
> diff --git a/doc/README.rockchip b/doc/README.rockchip
> index a408522346..cdeab2d961 100644
> --- a/doc/README.rockchip
> +++ b/doc/README.rockchip
> @@ -36,12 +36,13 @@ You will need:
> Building
> ========
>
> -At present seven RK3288 boards are supported:
> +At present eight RK3288 boards are supported:
>
> - EVB RK3288 - use evb-rk3288 configuration
> - Fennec RK3288 - use fennec-rk3288 configuration
> - Firefly RK3288 - use firefly-rk3288 configuration
> - Hisense Chromebook - use chromebook_jerry configuration
> + - MiQi RK3288 - use miqi-rk3288 configuration
> - PopMetal RK3288 - use popmetal-rk3288 configuration
> - Radxa Rock 2 - use rock2 configuration
> - Tinker RK3288 - use tinker-rk3288 configuration
> diff --git a/include/configs/miqi_rk3288.h b/include/configs/miqi_rk3288.h
> new file mode 100644
> index 0000000000..f686042499
> --- /dev/null
> +++ b/include/configs/miqi_rk3288.h
> @@ -0,0 +1,22 @@
> +/*
> + * (C) Copyright 2016 Rockchip Electronics Co., Ltd
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#define ROCKCHIP_DEVICE_SETTINGS \
> + "stdin=serial,cros-ec-keyb\0" \
> + "stdout=serial,vidconsole\0" \
> + "stderr=serial,vidconsole\0"
> +
> +#include <configs/rk3288_common.h>
> +
> +#define CONFIG_ENV_IS_IN_MMC
> +#define CONFIG_SYS_MMC_ENV_DEV 0
> +
> +#define CONFIG_SYS_WHITE_ON_BLACK
> +
> +#endif
Looks good to me,
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Thanks,
- Kever
^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v3 1/2] rockchip: cosmetic: Sort RK3288 boards
2017-03-29 23:23 ` [U-Boot] [PATCH v3 1/2] rockchip: cosmetic: Sort RK3288 boards Jernej Skrabec
2017-03-30 3:24 ` Kever Yang
@ 2017-03-30 7:04 ` Eddie Cai
2017-04-01 4:23 ` Simon Glass
2 siblings, 0 replies; 11+ messages in thread
From: Eddie Cai @ 2017-03-30 7:04 UTC (permalink / raw)
To: u-boot
HI Jernej
2017-03-30 7:23 GMT+08:00 Jernej Skrabec <jernej.skrabec@siol.net>:
> Sort rk3288 boards in alphabetical order.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
> ---
> Changes in v3:
> - new patch
>
> arch/arm/dts/Makefile | 10 ++--
> arch/arm/mach-rockchip/rk3288/Kconfig | 90 +++++++++++++++++-------------
> -----
> doc/README.rockchip | 2 +-
> 3 files changed, 51 insertions(+), 51 deletions(-)
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index afeb43ff66..3d9a80a603 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -29,15 +29,15 @@ dtb-$(CONFIG_EXYNOS5) += exynos5250-arndale.dtb \
> dtb-$(CONFIG_EXYNOS7420) += exynos7420-espresso7420.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += \
> rk3036-sdk.dtb \
> + rk3288-evb.dtb \
> + rk3288-fennec.dtb \
> rk3288-firefly.dtb \
> + rk3288-popmetal.dtb \
> + rk3288-rock2-square.dtb \
> + rk3288-tinker.dtb \
> rk3288-veyron-jerry.dtb \
> rk3288-veyron-mickey.dtb \
> rk3288-veyron-minnie.dtb \
> - rk3288-rock2-square.dtb \
> - rk3288-evb.dtb \
> - rk3288-fennec.dtb \
> - rk3288-tinker.dtb \
> - rk3288-popmetal.dtb \
> rk3328-evb.dtb \
> rk3399-evb.dtb
> dtb-$(CONFIG_ARCH_MESON) += \
> diff --git a/arch/arm/mach-rockchip/rk3288/Kconfig
> b/arch/arm/mach-rockchip/rk3288/Kconfig
> index 738a20d07c..13f7513813 100644
> --- a/arch/arm/mach-rockchip/rk3288/Kconfig
> +++ b/arch/arm/mach-rockchip/rk3288/Kconfig
> @@ -1,13 +1,34 @@
> if ROCKCHIP_RK3288
>
> -config TARGET_FIREFLY_RK3288
> - bool "Firefly-RK3288"
> +config TARGET_CHROMEBOOK_JERRY
> + bool "Google/Rockchip Veyron-Jerry Chromebook"
> select BOARD_LATE_INIT
> help
> - Firefly is a RK3288-based development board with 2 USB ports,
> - HDMI, VGA, micro-SD card, audio, WiFi and Gigabit Ethernet, It
> - also includes on-board eMMC and 1GB of SDRAM. Expansion
> connectors
> - provide access to display pins, I2C, SPI, UART and GPIOs.
> + Jerry is a RK3288-based clamshell device with 2 USB 3.0 ports,
> + HDMI, an 11.9 inch EDP display, micro-SD card, touchpad and
> + WiFi. It includes a Chrome OS EC (Cortex-M3) to provide access to
> + the keyboard and battery functions.
> +
> +config TARGET_CHROMEBIT_MICKEY
> + bool "Google/Rockchip Veyron-Mickey Chromebit"
> + select BOARD_LATE_INIT
> + help
> + Mickey is a small RK3288-based device with one USB 3.0 port, HDMI
> + and WiFi. It has a separate power port and is designed to connect
> + to the HDMI input of a monitor or TV. It has no internal battery.
> + Typically a USB hub or wireless keyboard/touchpad is used to get
> + keyboard and mouse access.
> +
> +config TARGET_CHROMEBOOK_MINNIE
> + bool "Google/Rockchip Veyron-Minnie Chromebook"
> + select BOARD_LATE_INIT
> + help
> + Minnie is a RK3288-based convertible clamshell device with 2 USB
> 3.0
> + ports, micro HDMI, a 10.1-inch 1280x800 EDP display, micro-SD
> card,
> + HD camera, touchpad, WiFi and Bluetooth. It includes a Chrome OS
> + EC (Cortex-M3) to provide access to the keyboard and battery
> + functions. It includes 2 or 4GB of SDRAM and 16 or 32GB of
> + internal MMC. The product name is ASUS Chromebook Flip.
>
> config TARGET_EVB_RK3288
> bool "Evb-RK3288"
> @@ -27,6 +48,15 @@ config TARGET_FENNEC_RK3288
> includes on-board eMMC and 2GB of SDRAM. Expansion connectors
> provide access to display pins, I2C, SPI, UART and GPIOs.
>
> +config TARGET_FIREFLY_RK3288
> + bool "Firefly-RK3288"
> + select BOARD_LATE_INIT
> + help
> + Firefly is a RK3288-based development board with 2 USB ports,
> + HDMI, VGA, micro-SD card, audio, WiFi and Gigabit Ethernet, It
> + also includes on-board eMMC and 1GB of SDRAM. Expansion
> connectors
> + provide access to display pins, I2C, SPI, UART and GPIOs.
> +
> config TARGET_POPMETAL_RK3288
> bool "PopMetal-RK3288"
> select BOARD_LATE_INIT
> @@ -37,45 +67,6 @@ config TARGET_POPMETAL_RK3288
> 2GB DDR3. Expansion connectors provide access to I2C, SPI, UART,
> GPIOs and display interface.
>
> -config TARGET_TINKER_RK3288
> - bool "Tinker-RK3288"
> - select BOARD_LATE_INIT
> - help
> - Tinker is a RK3288-based development board with 2 USB ports,
> HDMI,
> - micro-SD card, audio, Gigabit Ethernet. It also includes on-board
> - 8GB eMMC and 2GB of SDRAM. Expansion connectors provide access to
> - I2C, SPI, UART, GPIOs.
> -
> -config TARGET_CHROMEBOOK_JERRY
> - bool "Google/Rockchip Veyron-Jerry Chromebook"
> - select BOARD_LATE_INIT
> - help
> - Jerry is a RK3288-based clamshell device with 2 USB 3.0 ports,
> - HDMI, an 11.9 inch EDP display, micro-SD card, touchpad and
> - WiFi. It includes a Chrome OS EC (Cortex-M3) to provide access to
> - the keyboard and battery functions.
> -
> -config TARGET_CHROMEBIT_MICKEY
> - bool "Google/Rockchip Veyron-Mickey Chromebit"
> - select BOARD_LATE_INIT
> - help
> - Mickey is a small RK3288-based device with one USB 3.0 port, HDMI
> - and WiFi. It has a separate power port and is designed to connect
> - to the HDMI input of a monitor or TV. It has no internal battery.
> - Typically a USB hub or wireless keyboard/touchpad is used to get
> - keyboard and mouse access.
> -
> -config TARGET_CHROMEBOOK_MINNIE
> - bool "Google/Rockchip Veyron-Minnie Chromebook"
> - select BOARD_LATE_INIT
> - help
> - Minnie is a RK3288-based convertible clamshell device with 2 USB
> 3.0
> - ports, micro HDMI, a 10.1-inch 1280x800 EDP display, micro-SD
> card,
> - HD camera, touchpad, WiFi and Bluetooth. It includes a Chrome OS
> - EC (Cortex-M3) to provide access to the keyboard and battery
> - functions. It includes 2 or 4GB of SDRAM and 16 or 32GB of
> - internal MMC. The product name is ASUS Chromebook Flip.
> -
> config TARGET_ROCK2
> bool "Radxa Rock 2"
> select BOARD_LATE_INIT
> @@ -85,6 +76,15 @@ config TARGET_ROCK2
> space for a real-time-clock battery. There is also an expansion
> interface which provides access to many pins.
>
> +config TARGET_TINKER_RK3288
> + bool "Tinker-RK3288"
> + select BOARD_LATE_INIT
> + help
> + Tinker is a RK3288-based development board with 2 USB ports,
> HDMI,
> + micro-SD card, audio, Gigabit Ethernet. It also includes on-board
> + 8GB eMMC and 2GB of SDRAM. Expansion connectors provide access to
> + I2C, SPI, UART, GPIOs.
> +
> config ROCKCHIP_FAST_SPL
> bool "Change the CPU to full speed in SPL"
> depends on TARGET_CHROMEBOOK_JERRY
> diff --git a/doc/README.rockchip b/doc/README.rockchip
> index 186a1a007e..a408522346 100644
> --- a/doc/README.rockchip
> +++ b/doc/README.rockchip
> @@ -42,9 +42,9 @@ At present seven RK3288 boards are supported:
> - Fennec RK3288 - use fennec-rk3288 configuration
> - Firefly RK3288 - use firefly-rk3288 configuration
> - Hisense Chromebook - use chromebook_jerry configuration
> - - Tinker RK3288 - use tinker-rk3288 configuration
> - PopMetal RK3288 - use popmetal-rk3288 configuration
> - Radxa Rock 2 - use rock2 configuration
> + - Tinker RK3288 - use tinker-rk3288 configuration
>
> Two RK3036 board are supported:
>
> --
> 2.12.1
>
>
^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v3 2/2] rockchip: Add support for MiQi rk3288 board
2017-03-29 23:23 ` [U-Boot] [PATCH v3 2/2] rockchip: Add support for MiQi rk3288 board Jernej Skrabec
2017-03-30 3:25 ` Kever Yang
@ 2017-03-30 7:05 ` Eddie Cai
2017-04-01 4:23 ` Simon Glass
2 siblings, 0 replies; 11+ messages in thread
From: Eddie Cai @ 2017-03-30 7:05 UTC (permalink / raw)
To: u-boot
HI Jernej
2017-03-30 7:23 GMT+08:00 Jernej Skrabec <jernej.skrabec@siol.net>:
> MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
> micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
> expansion ports.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
> ---
> Changes in v3:
> - split out cosmetic changes into a new patch
>
> Changes in v2:
> - change license to SPDX identifier
> - reorder boards in alphabetical order in Kconfig and Makefile
>
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/rk3288-miqi.dts | 46 ++++
> arch/arm/dts/rk3288-miqi.dtsi | 423
> ++++++++++++++++++++++++++++++++
> arch/arm/mach-rockchip/rk3288/Kconfig | 11 +
> board/mqmaker/miqi_rk3288/Kconfig | 15 ++
> board/mqmaker/miqi_rk3288/MAINTAINERS | 6 +
> board/mqmaker/miqi_rk3288/Makefile | 7 +
> board/mqmaker/miqi_rk3288/miqi-rk3288.c | 15 ++
> configs/miqi-rk3288_defconfig | 73 ++++++
> doc/README.rockchip | 3 +-
> include/configs/miqi_rk3288.h | 22 ++
> 11 files changed, 621 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/dts/rk3288-miqi.dts
> create mode 100644 arch/arm/dts/rk3288-miqi.dtsi
> create mode 100644 board/mqmaker/miqi_rk3288/Kconfig
> create mode 100644 board/mqmaker/miqi_rk3288/MAINTAINERS
> create mode 100644 board/mqmaker/miqi_rk3288/Makefile
> create mode 100644 board/mqmaker/miqi_rk3288/miqi-rk3288.c
> create mode 100644 configs/miqi-rk3288_defconfig
> create mode 100644 include/configs/miqi_rk3288.h
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 3d9a80a603..9e95386ca5 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -32,6 +32,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
> rk3288-evb.dtb \
> rk3288-fennec.dtb \
> rk3288-firefly.dtb \
> + rk3288-miqi.dtb \
> rk3288-popmetal.dtb \
> rk3288-rock2-square.dtb \
> rk3288-tinker.dtb \
> diff --git a/arch/arm/dts/rk3288-miqi.dts b/arch/arm/dts/rk3288-miqi.dts
> new file mode 100644
> index 0000000000..7b92caf024
> --- /dev/null
> +++ b/arch/arm/dts/rk3288-miqi.dts
> @@ -0,0 +1,46 @@
> +/*
> + * (C) Copyright 2016 Rockchip Electronics Co., Ltd
> + *
> + * SPDX-License-Identifier: GPL-2.0+ X11
> + */
> +
> +/dts-v1/;
> +#include "rk3288-miqi.dtsi"
> +
> +/ {
> + model = "mqmaker MiQi";
> + compatible = "mqmaker,miqi", "rockchip,rk3288";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + };
> +};
> +
> +&dmc {
> + rockchip,pctl-timing = <0x29a 0xc8 0x1f8 0x42 0x4e 0x4 0xea 0xa
> + 0x5 0x0 0xa 0x7 0x19 0x24 0xa 0x7
> + 0x5 0xa 0x5 0x200 0x5 0x10 0x40 0x0
> + 0x1 0x7 0x7 0x4 0xc 0x43 0x100 0x0
> + 0x5 0x0>;
> + rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200
> + 0xa60 0x40 0x10 0x0>;
> + rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 9 1>;
> +};
> +
> +
> +&pinctrl {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&uart2 {
> + u-boot,dm-pre-reloc;
> + reg-shift = <2>;
> +};
> +
> +&sdmmc {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&emmc {
> + u-boot,dm-pre-reloc;
> +};
> diff --git a/arch/arm/dts/rk3288-miqi.dtsi b/arch/arm/dts/rk3288-miqi.dtsi
> new file mode 100644
> index 0000000000..47dc0f9d74
> --- /dev/null
> +++ b/arch/arm/dts/rk3288-miqi.dtsi
> @@ -0,0 +1,423 @@
> +/*
> + * Copyright (c) 2016 Heiko Stuebner <heiko@sntech.de>
> + *
> + * SPDX-License-Identifier: GPL-2.0+ X11
> + */
> +
> +#include "rk3288.dtsi"
> +
> +/ {
> + memory {
> + device_type = "memory";
> + reg = <0 0x80000000>;
> + };
> +
> + ext_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <125000000>;
> + clock-output-names = "ext_gmac";
> + };
> +
> + io_domains: io-domains {
> + compatible = "rockchip,rk3288-io-voltage-domain";
> + rockchip,grf = <&grf>;
> +
> + audio-supply = <&vcca_33>;
> + flash0-supply = <&vcc_flash>;
> + flash1-supply = <&vcc_lan>;
> + gpio30-supply = <&vcc_io>;
> + gpio1830-supply = <&vcc_io>;
> + lcdc-supply = <&vcc_io>;
> + sdcard-supply = <&vccio_sd>;
> + wifi-supply = <&vcc_18>;
> + };
> +
> +
> + leds {
> + u-boot,dm-pre-reloc;
> + compatible = "gpio-leds";
> +
> + work {
> + u-boot,dm-pre-reloc;
> + gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
> + label = "miqi:green:user";
> + linux,default-trigger = "default-on";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_ctl>;
> + };
> + };
> +
> + vcc_flash: flash-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_flash";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_host: usb-host-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&host_vbus_drv>;
> + regulator-name = "vcc_host";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcc_sd: sdmmc-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_pwr>;
> + regulator-name = "vcc_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <100000>;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_sys: vsys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +};
> +
> +&cpu0 {
> + cpu0-supply = <&vdd_cpu>;
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + disable-wp;
> + non-removable;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>;
> + vmmc-supply = <&vcc_io>;
> + vqmmc-supply = <&vcc_flash>;
> + status = "okay";
> +};
> +
> +&gmac {
> + assigned-clocks = <&cru SCLK_MAC>;
> + assigned-clock-parents = <&ext_gmac>;
> + clock_in_out = "input";
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>;
> + phy-supply = <&vcc_lan>;
> + phy-mode = "rgmii";
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 1000000>;
> + snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
> + tx_delay = <0x30>;
> + rx_delay = <0x10>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + ddc-i2c-bus = <&i2c5>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + vdd_cpu: syr827 at 40 {
> + compatible = "silergy,syr827";
> + fcs,suspend-voltage-selector = <1>;
> + reg = <0x40>;
> + regulator-name = "vdd_cpu";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-enable-ramp-delay = <300>;
> + regulator-ramp-delay = <8000>;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vdd_gpu: syr828 at 41 {
> + compatible = "silergy,syr828";
> + fcs,suspend-voltage-selector = <1>;
> + reg = <0x41>;
> + regulator-name = "vdd_gpu";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + hym8563: hym8563 at 51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "xin32k";
> + };
> +
> + act8846: act8846 at 5a {
> + compatible = "active-semi,act8846";
> + reg = <0x5a>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_vsel>;
> + system-power-controller;
> +
> + vp1-supply = <&vcc_sys>;
> + vp2-supply = <&vcc_sys>;
> + vp3-supply = <&vcc_sys>;
> + vp4-supply = <&vcc_sys>;
> + inl1-supply = <&vcc_sys>;
> + inl2-supply = <&vcc_sys>;
> + inl3-supply = <&vcc_20>;
> +
> + regulators {
> + vcc_ddr: REG1 {
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + };
> +
> + vcc_io: REG2 {
> + regulator-name = "vcc_io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vdd_log: REG3 {
> + regulator-name = "vdd_log";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + };
> +
> + vcc_20: REG4 {
> + regulator-name = "vcc_20";
> + regulator-min-microvolt = <2000000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-always-on;
> + };
> +
> + vccio_sd: REG5 {
> + regulator-name = "vccio_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vdd10_lcd: REG6 {
> + regulator-name = "vdd10_lcd";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + };
> +
> + vcca_18: REG7 {
> + regulator-name = "vcca_18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + vcca_33: REG8 {
> + regulator-name = "vcca_33";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vcc_lan: REG9 {
> + regulator-name = "vcc_lan";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vdd_10: REG10 {
> + regulator-name = "vdd_10";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + };
> +
> + vcc_18: REG11 {
> + regulator-name = "vcc_18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vcc18_lcd: REG12 {
> + regulator-name = "vcc18_lcd";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c4 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&pinctrl {
> + pcfg_output_high: pcfg-output-high {
> + output-high;
> + };
> +
> + pcfg_output_low: pcfg-output-low {
> + output-low;
> + };
> +
> + pcfg_pull_up_drv_12ma: pcfg-pull-up-drv-12ma {
> + bias-pull-up;
> + drive-strength = <12>;
> + };
> +
> + act8846 {
> + pmic_int: pmic-int {
> + rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + pmic_sleep: pmic-sleep {
> + rockchip,pins = <0 0 RK_FUNC_GPIO
> &pcfg_output_low>;
> + };
> +
> + pmic_vsel: pmic-vsel {
> + rockchip,pins = <7 1 RK_FUNC_GPIO
> &pcfg_output_low>;
> + };
> + };
> +
> + gmac {
> + phy_int: phy-int {
> + rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + phy_pmeb: phy-pmeb {
> + rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + phy_rst: phy-rst {
> + rockchip,pins = <4 8 RK_FUNC_GPIO
> &pcfg_output_high>;
> + };
> + };
> +
> + leds {
> + led_ctl: led-ctl {
> + rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdmmc {
> + /*
> + * Default drive strength isn't enough to achieve even
> + * high-speed mode on firefly board so bump up to 12ma.
> + */
> + sdmmc_bus4: sdmmc-bus4 {
> + rockchip,pins = <6 16 RK_FUNC_1
> &pcfg_pull_up_drv_12ma>,
> + <6 17 RK_FUNC_1
> &pcfg_pull_up_drv_12ma>,
> + <6 18 RK_FUNC_1
> &pcfg_pull_up_drv_12ma>,
> + <6 19 RK_FUNC_1
> &pcfg_pull_up_drv_12ma>;
> + };
> +
> + sdmmc_clk: sdmmc-clk {
> + rockchip,pins = <6 20 RK_FUNC_1
> &pcfg_pull_none_12ma>;
> + };
> +
> + sdmmc_cmd: sdmmc-cmd {
> + rockchip,pins = <6 21 RK_FUNC_1
> &pcfg_pull_up_drv_12ma>;
> + };
> +
> + sdmmc_pwr: sdmmc-pwr {
> + rockchip,pins = <7 11 RK_FUNC_GPIO
> &pcfg_pull_none>;
> + };
> + };
> +
> + usb_host {
> + host_vbus_drv: host-vbus-drv {
> + rockchip,pins = <0 14 RK_FUNC_GPIO
> &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_18>;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + card-detect-delay = <200>;
> + disable-wp;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
> + vmmc-supply = <&vcc_sd>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-mode = <0>;
> + rockchip,hw-tshut-polarity = <0>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&usbphy {
> + status = "okay";
> +};
> +
> +&usb_host1 {
> + vbus-supply = <&vcc_host>;
> + status = "okay";
> +};
> +
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&vopl {
> + status = "okay";
> +};
> +
> +&vopl_mmu {
> + status = "okay";
> +};
> +
> +&wdt {
> + status = "okay";
> +};
> diff --git a/arch/arm/mach-rockchip/rk3288/Kconfig
> b/arch/arm/mach-rockchip/rk3288/Kconfig
> index 13f7513813..8e7355ece4 100644
> --- a/arch/arm/mach-rockchip/rk3288/Kconfig
> +++ b/arch/arm/mach-rockchip/rk3288/Kconfig
> @@ -57,6 +57,15 @@ config TARGET_FIREFLY_RK3288
> also includes on-board eMMC and 1GB of SDRAM. Expansion
> connectors
> provide access to display pins, I2C, SPI, UART and GPIOs.
>
> +config TARGET_MIQI_RK3288
> + bool "MiQi-RK3288"
> + select BOARD_LATE_INIT
> + help
> + MiQi-RK3288 is a RK3288-based development board with 4 USB 2.0
> + ports, HDMI, micro-SD card, 16 GB eMMC and Gigabit Ethernet. It
> + has 1 or 2 GiB SDRAM. Expansion connectors provide access to
> + I2C, SPI, UART, GPIOs and fan control.
> +
> config TARGET_POPMETAL_RK3288
> bool "PopMetal-RK3288"
> select BOARD_LATE_INIT
> @@ -118,6 +127,8 @@ source "board/firefly/firefly-rk3288/Kconfig"
>
> source "board/google/veyron/Kconfig"
>
> +source "board/mqmaker/miqi_rk3288/Kconfig"
> +
> source "board/radxa/rock2/Kconfig"
>
> source "board/rockchip/evb_rk3288/Kconfig"
> diff --git a/board/mqmaker/miqi_rk3288/Kconfig
> b/board/mqmaker/miqi_rk3288/Kconfig
> new file mode 100644
> index 0000000000..232a112090
> --- /dev/null
> +++ b/board/mqmaker/miqi_rk3288/Kconfig
> @@ -0,0 +1,15 @@
> +if TARGET_MIQI_RK3288
> +
> +config SYS_BOARD
> + default "miqi_rk3288"
> +
> +config SYS_VENDOR
> + default "mqmaker"
> +
> +config SYS_CONFIG_NAME
> + default "miqi_rk3288"
> +
> +config BOARD_SPECIFIC_OPTIONS # dummy
> + def_bool y
> +
> +endif
> diff --git a/board/mqmaker/miqi_rk3288/MAINTAINERS
> b/board/mqmaker/miqi_rk3288/MAINTAINERS
> new file mode 100644
> index 0000000000..053a5e6028
> --- /dev/null
> +++ b/board/mqmaker/miqi_rk3288/MAINTAINERS
> @@ -0,0 +1,6 @@
> +MIQI
> +M: Jernej Skrabec <jernej.skrabec@siol.net>
> +S: Maintained
> +F: board/mqmaker/miqi_rk3288
> +F: include/configs/miqi_rk3288.h
> +F: configs/miqi-rk3288_defconfig
> diff --git a/board/mqmaker/miqi_rk3288/Makefile
> b/board/mqmaker/miqi_rk3288/Makefile
> new file mode 100644
> index 0000000000..ec95affb39
> --- /dev/null
> +++ b/board/mqmaker/miqi_rk3288/Makefile
> @@ -0,0 +1,7 @@
> +#
> +# (C) Copyright 2016 Rockchip Electronics Co., Ltd
> +#
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +
> +obj-y += miqi-rk3288.o
> diff --git a/board/mqmaker/miqi_rk3288/miqi-rk3288.c
> b/board/mqmaker/miqi_rk3288/miqi-rk3288.c
> new file mode 100644
> index 0000000000..a82f0ae283
> --- /dev/null
> +++ b/board/mqmaker/miqi_rk3288/miqi-rk3288.c
> @@ -0,0 +1,15 @@
> +/*
> + * (C) Copyright 2016 Rockchip Electronics Co., Ltd
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <spl.h>
> +
> +void board_boot_order(u32 *spl_boot_list)
> +{
> + /* eMMC prior to sdcard. */
> + spl_boot_list[0] = BOOT_DEVICE_MMC2;
> + spl_boot_list[1] = BOOT_DEVICE_MMC1;
> +}
> diff --git a/configs/miqi-rk3288_defconfig b/configs/miqi-rk3288_defconfig
> new file mode 100644
> index 0000000000..203824b893
> --- /dev/null
> +++ b/configs/miqi-rk3288_defconfig
> @@ -0,0 +1,73 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_ROCKCHIP=y
> +CONFIG_SYS_MALLOC_F_LEN=0x2000
> +CONFIG_ROCKCHIP_RK3288=y
> +CONFIG_ROCKCHIP_SPL_BACK_TO_BROM=y
> +CONFIG_TARGET_MIQI_RK3288=y
> +CONFIG_SPL_STACK_R_ADDR=0x80000
> +CONFIG_DEFAULT_DEVICE_TREE="rk3288-miqi"
> +CONFIG_SILENT_CONSOLE=y
> +# CONFIG_DISPLAY_CPUINFO is not set
> +CONFIG_SPL_STACK_R=y
> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x2000
> +# CONFIG_CMD_IMLS is not set
> +CONFIG_CMD_GPT=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_SF=y
> +CONFIG_CMD_SPI=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_GPIO=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_PMIC=y
> +CONFIG_CMD_REGULATOR=y
> +# CONFIG_SPL_DOS_PARTITION is not set
> +# CONFIG_SPL_ISO_PARTITION is not set
> +# CONFIG_SPL_EFI_PARTITION is not set
> +CONFIG_SPL_PARTITION_UUIDS=y
> +CONFIG_SPL_OF_CONTROL=y
> +CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names
> interrupt-parent assigned-clocks assigned-clock-rates
> assigned-clock-parents"
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_REGMAP=y
> +CONFIG_SPL_REGMAP=y
> +CONFIG_SYSCON=y
> +CONFIG_SPL_SYSCON=y
> +# CONFIG_SPL_SIMPLE_BUS is not set
> +CONFIG_CLK=y
> +CONFIG_SPL_CLK=y
> +CONFIG_ROCKCHIP_GPIO=y
> +CONFIG_SYS_I2C_ROCKCHIP=y
> +CONFIG_MMC_DW=y
> +CONFIG_MMC_DW_ROCKCHIP=y
> +CONFIG_DM_ETH=y
> +CONFIG_ETH_DESIGNWARE=y
> +CONFIG_GMAC_ROCKCHIP=y
> +CONFIG_PINCTRL=y
> +CONFIG_SPL_PINCTRL=y
> +# CONFIG_SPL_PINCTRL_FULL is not set
> +CONFIG_ROCKCHIP_RK3288_PINCTRL=y
> +CONFIG_DM_PMIC=y
> +CONFIG_PMIC_ACT8846=y
> +CONFIG_REGULATOR_ACT8846=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_PWM_ROCKCHIP=y
> +CONFIG_RAM=y
> +CONFIG_SPL_RAM=y
> +CONFIG_DEBUG_UART=y
> +CONFIG_DEBUG_UART_BASE=0xff690000
> +CONFIG_DEBUG_UART_CLOCK=24000000
> +CONFIG_DEBUG_UART_SHIFT=2
> +CONFIG_SYS_NS16550=y
> +CONFIG_ROCKCHIP_SERIAL=y
> +CONFIG_SYSRESET=y
> +CONFIG_USB=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_DM_VIDEO=y
> +CONFIG_DISPLAY=y
> +CONFIG_VIDEO_ROCKCHIP=y
> +CONFIG_CONSOLE_SCROLL_LINES=10
> +CONFIG_USE_TINY_PRINTF=y
> +CONFIG_CMD_DHRYSTONE=y
> +CONFIG_ERRNO_STR=y
> diff --git a/doc/README.rockchip b/doc/README.rockchip
> index a408522346..cdeab2d961 100644
> --- a/doc/README.rockchip
> +++ b/doc/README.rockchip
> @@ -36,12 +36,13 @@ You will need:
> Building
> ========
>
> -At present seven RK3288 boards are supported:
> +At present eight RK3288 boards are supported:
>
> - EVB RK3288 - use evb-rk3288 configuration
> - Fennec RK3288 - use fennec-rk3288 configuration
> - Firefly RK3288 - use firefly-rk3288 configuration
> - Hisense Chromebook - use chromebook_jerry configuration
> + - MiQi RK3288 - use miqi-rk3288 configuration
> - PopMetal RK3288 - use popmetal-rk3288 configuration
> - Radxa Rock 2 - use rock2 configuration
> - Tinker RK3288 - use tinker-rk3288 configuration
> diff --git a/include/configs/miqi_rk3288.h b/include/configs/miqi_rk3288.h
> new file mode 100644
> index 0000000000..f686042499
> --- /dev/null
> +++ b/include/configs/miqi_rk3288.h
> @@ -0,0 +1,22 @@
> +/*
> + * (C) Copyright 2016 Rockchip Electronics Co., Ltd
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#define ROCKCHIP_DEVICE_SETTINGS \
> + "stdin=serial,cros-ec-keyb\0" \
> + "stdout=serial,vidconsole\0" \
> + "stderr=serial,vidconsole\0"
> +
> +#include <configs/rk3288_common.h>
> +
> +#define CONFIG_ENV_IS_IN_MMC
> +#define CONFIG_SYS_MMC_ENV_DEV 0
> +
> +#define CONFIG_SYS_WHITE_ON_BLACK
> +
> +#endif
> --
> 2.12.1
>
>
^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v3 1/2] rockchip: cosmetic: Sort RK3288 boards
2017-03-29 23:23 ` [U-Boot] [PATCH v3 1/2] rockchip: cosmetic: Sort RK3288 boards Jernej Skrabec
2017-03-30 3:24 ` Kever Yang
2017-03-30 7:04 ` Eddie Cai
@ 2017-04-01 4:23 ` Simon Glass
2017-04-05 1:05 ` Simon Glass
2 siblings, 1 reply; 11+ messages in thread
From: Simon Glass @ 2017-04-01 4:23 UTC (permalink / raw)
To: u-boot
On 29 March 2017 at 17:23, Jernej Skrabec <jernej.skrabec@siol.net> wrote:
> Sort rk3288 boards in alphabetical order.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
> ---
> Changes in v3:
> - new patch
>
> arch/arm/dts/Makefile | 10 ++--
> arch/arm/mach-rockchip/rk3288/Kconfig | 90 +++++++++++++++++------------------
> doc/README.rockchip | 2 +-
> 3 files changed, 51 insertions(+), 51 deletions(-)
>
Acked-by: Simon Glass <sjg@chromium.org>
^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v3 2/2] rockchip: Add support for MiQi rk3288 board
2017-03-29 23:23 ` [U-Boot] [PATCH v3 2/2] rockchip: Add support for MiQi rk3288 board Jernej Skrabec
2017-03-30 3:25 ` Kever Yang
2017-03-30 7:05 ` Eddie Cai
@ 2017-04-01 4:23 ` Simon Glass
2017-04-05 1:05 ` Simon Glass
2 siblings, 1 reply; 11+ messages in thread
From: Simon Glass @ 2017-04-01 4:23 UTC (permalink / raw)
To: u-boot
On 29 March 2017 at 17:23, Jernej Skrabec <jernej.skrabec@siol.net> wrote:
> MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
> micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
> expansion ports.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
> ---
> Changes in v3:
> - split out cosmetic changes into a new patch
>
> Changes in v2:
> - change license to SPDX identifier
> - reorder boards in alphabetical order in Kconfig and Makefile
>
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/rk3288-miqi.dts | 46 ++++
> arch/arm/dts/rk3288-miqi.dtsi | 423 ++++++++++++++++++++++++++++++++
> arch/arm/mach-rockchip/rk3288/Kconfig | 11 +
> board/mqmaker/miqi_rk3288/Kconfig | 15 ++
> board/mqmaker/miqi_rk3288/MAINTAINERS | 6 +
> board/mqmaker/miqi_rk3288/Makefile | 7 +
> board/mqmaker/miqi_rk3288/miqi-rk3288.c | 15 ++
> configs/miqi-rk3288_defconfig | 73 ++++++
> doc/README.rockchip | 3 +-
> include/configs/miqi_rk3288.h | 22 ++
> 11 files changed, 621 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/dts/rk3288-miqi.dts
> create mode 100644 arch/arm/dts/rk3288-miqi.dtsi
> create mode 100644 board/mqmaker/miqi_rk3288/Kconfig
> create mode 100644 board/mqmaker/miqi_rk3288/MAINTAINERS
> create mode 100644 board/mqmaker/miqi_rk3288/Makefile
> create mode 100644 board/mqmaker/miqi_rk3288/miqi-rk3288.c
> create mode 100644 configs/miqi-rk3288_defconfig
> create mode 100644 include/configs/miqi_rk3288.h
Acked-by: Simon Glass <sjg@chromium.org>
^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v3 1/2] rockchip: cosmetic: Sort RK3288 boards
2017-04-01 4:23 ` Simon Glass
@ 2017-04-05 1:05 ` Simon Glass
0 siblings, 0 replies; 11+ messages in thread
From: Simon Glass @ 2017-04-05 1:05 UTC (permalink / raw)
To: u-boot
On 31 March 2017 at 22:23, Simon Glass <sjg@chromium.org> wrote:
> On 29 March 2017 at 17:23, Jernej Skrabec <jernej.skrabec@siol.net> wrote:
>> Sort rk3288 boards in alphabetical order.
>>
>> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
>> ---
>> Changes in v3:
>> - new patch
>>
>> arch/arm/dts/Makefile | 10 ++--
>> arch/arm/mach-rockchip/rk3288/Kconfig | 90 +++++++++++++++++------------------
>> doc/README.rockchip | 2 +-
>> 3 files changed, 51 insertions(+), 51 deletions(-)
>>
>
> Acked-by: Simon Glass <sjg@chromium.org>
Applied to u-boot-rockchip, thanks!
^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v3 2/2] rockchip: Add support for MiQi rk3288 board
2017-04-01 4:23 ` Simon Glass
@ 2017-04-05 1:05 ` Simon Glass
0 siblings, 0 replies; 11+ messages in thread
From: Simon Glass @ 2017-04-05 1:05 UTC (permalink / raw)
To: u-boot
On 31 March 2017 at 22:23, Simon Glass <sjg@chromium.org> wrote:
> On 29 March 2017 at 17:23, Jernej Skrabec <jernej.skrabec@siol.net> wrote:
>> MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
>> micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
>> expansion ports.
>>
>> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
>> ---
>> Changes in v3:
>> - split out cosmetic changes into a new patch
>>
>> Changes in v2:
>> - change license to SPDX identifier
>> - reorder boards in alphabetical order in Kconfig and Makefile
>>
>> arch/arm/dts/Makefile | 1 +
>> arch/arm/dts/rk3288-miqi.dts | 46 ++++
>> arch/arm/dts/rk3288-miqi.dtsi | 423 ++++++++++++++++++++++++++++++++
>> arch/arm/mach-rockchip/rk3288/Kconfig | 11 +
>> board/mqmaker/miqi_rk3288/Kconfig | 15 ++
>> board/mqmaker/miqi_rk3288/MAINTAINERS | 6 +
>> board/mqmaker/miqi_rk3288/Makefile | 7 +
>> board/mqmaker/miqi_rk3288/miqi-rk3288.c | 15 ++
>> configs/miqi-rk3288_defconfig | 73 ++++++
>> doc/README.rockchip | 3 +-
>> include/configs/miqi_rk3288.h | 22 ++
>> 11 files changed, 621 insertions(+), 1 deletion(-)
>> create mode 100644 arch/arm/dts/rk3288-miqi.dts
>> create mode 100644 arch/arm/dts/rk3288-miqi.dtsi
>> create mode 100644 board/mqmaker/miqi_rk3288/Kconfig
>> create mode 100644 board/mqmaker/miqi_rk3288/MAINTAINERS
>> create mode 100644 board/mqmaker/miqi_rk3288/Makefile
>> create mode 100644 board/mqmaker/miqi_rk3288/miqi-rk3288.c
>> create mode 100644 configs/miqi-rk3288_defconfig
>> create mode 100644 include/configs/miqi_rk3288.h
>
> Acked-by: Simon Glass <sjg@chromium.org>
Applied to u-boot-rockchip, thanks!
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2017-04-05 1:05 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-03-29 23:23 [U-Boot] [PATCH v3 0/2] rockchip: Add support for MiQi board Jernej Skrabec
2017-03-29 23:23 ` [U-Boot] [PATCH v3 1/2] rockchip: cosmetic: Sort RK3288 boards Jernej Skrabec
2017-03-30 3:24 ` Kever Yang
2017-03-30 7:04 ` Eddie Cai
2017-04-01 4:23 ` Simon Glass
2017-04-05 1:05 ` Simon Glass
2017-03-29 23:23 ` [U-Boot] [PATCH v3 2/2] rockchip: Add support for MiQi rk3288 board Jernej Skrabec
2017-03-30 3:25 ` Kever Yang
2017-03-30 7:05 ` Eddie Cai
2017-04-01 4:23 ` Simon Glass
2017-04-05 1:05 ` Simon Glass
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.