* [PATCH] arm64: dts: rockchip: Add basic support for orion-r68
@ 2016-07-14 12:28 ` Matthias Brugger
0 siblings, 0 replies; 5+ messages in thread
From: Matthias Brugger @ 2016-07-14 12:28 UTC (permalink / raw)
To: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, heiko,
catalin.marinas, will.deacon
Cc: dianders, briannorris, romain.perier, amstan, wxt, zyw, jay.xu,
olof, afaerber, mbrugger, chauveau.julien, edubezval,
sudeep.holla, shawn.lin, devicetree, linux-arm-kernel,
linux-rockchip, linux-kernel, Matthias Brugger
This patch adds basic support for the Tronsmart orion r86 set-top-box.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
---
Changes since v1:
- change memory node to 2GB
- change compatible and file name
- add uart4
- add second led
Documentation/devicetree/bindings/arm/rockchip.txt | 4 +
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3368-orion-r68-meta.dts | 382 +++++++++++++++++++++
3 files changed, 387 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 715d960..1d5c65e0 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -110,3 +110,7 @@ Rockchip platforms device tree bindings
- Rockchip RK3399 evb:
Required root node properties:
- compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
+
+- Tronsmart Orion R68 Meta
+ Required root node properties:
+ - compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 7037a16..87669f6 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
new file mode 100644
index 0000000..8c8671f
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
@@ -0,0 +1,382 @@
+/*
+ * Copyright (c) 2016 Matthias Brugger <mbrugger@suse.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "rk3368.dtsi"
+
+/ {
+ model = "Rockchip Orion R68";
+ compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ pinctrl-0 = <&emmc_reset>;
+ pinctrl-names = "default";
+ reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ ext_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ };
+
+ keys: gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_key>;
+
+ button@0 {
+ gpio-key,wakeup = <1>;
+ gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ label = "GPIO Power";
+ linux,code = <116>;
+ };
+ };
+
+ leds: gpio-leds {
+ compatible = "gpio-leds";
+
+ red {
+ gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ label = "orion:red:led";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_ctl>;
+ default-state = "on";
+ };
+
+ blue {
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ label = "orion:blue:led";
+ pinctrl-names = "default";
+ pinctrl-0 = <&stby_pwren>;
+ default-state = "off";
+ };
+ };
+
+ vcc_18: vcc18-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ /* supplies both host and otg */
+ vcc_host: vcc-host-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 4 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vcc_host";
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vccio_sd: vcc-io-sd-regulator {
+ regulator-name= "vccio_sd";
+ gpio = <&gpio0 9 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_sd: vcc-sd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sd";
+ gpio = <&gpio3 11 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_io: vcc-io-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_lan: vcc-lan-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_lan";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_sys: vcc-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vccio_wl: vccio-wl-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vccio_wl";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vdd_10: vdd-10-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_10";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ disable-wp;
+ mmc-pwrseq = <&emmc_pwrseq>;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ status = "okay";
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ phy-supply = <&vcc_lan>;
+ phy-mode = "rgmii";
+ clock_in_out = "input";
+ snps,reset-gpio = <&gpio3 12 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ status = "ok";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: syr827@40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-enable-ramp-delay = <300>;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <8000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ hym8563: hym8563@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ /* rtc_int is not connected */
+ };
+};
+
+&pinctrl {
+ pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+ bias-disable;
+ drive-strength = <8>;
+ };
+
+ pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
+ emmc {
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 19 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 20 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 21 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 22 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 23 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 24 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 25 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
+ };
+
+ emmc-clk {
+ rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
+ };
+
+ emmc-cmd {
+ rockchip,pins = <1 26 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
+ };
+
+ emmc_reset: emmc-reset {
+ rockchip,pins = <2 3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ keys {
+ pwr_key: pwr-key {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ leds {
+ stby_pwren: stby-pwren {
+ rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ led_ctl: led-ctl {
+ rockchip,pins = <3 29 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <2 9 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <2 10 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_cd: sdmmc-cd {
+ rockchip,pins = <2 11 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_bus1: sdmmc-bus1 {
+ rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 6 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 7 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 8 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+ };
+
+ usb {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&saradc {
+ vref-supply = <&vcc_18>;
+ status = "okay";
+};
+
+&sdmmc {
+ clock-frequency = <50000000>;
+ clock-freq-min-max = <400000 50000000>;
+ cap-sd-highspeed;
+ supports-sd;
+ broken-cd;
+ card-detect-delay = <200>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ bus-width = <4>;
+ num-slots = <1>;
+ ignore-pm-notify;
+ keep-power-in-suspend;
+
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_xfer>;
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
--
2.6.6
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH] arm64: dts: rockchip: Add basic support for orion-r68
@ 2016-07-14 12:28 ` Matthias Brugger
0 siblings, 0 replies; 5+ messages in thread
From: Matthias Brugger @ 2016-07-14 12:28 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8,
mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
galak-sgV2jX0FEOL9JmXXK+q4OQ, heiko-4mtYJXux2i+zQB+pC5nmwQ,
catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8
Cc: dianders-F7+t8E8rja9g9hUCZPvPmw,
briannorris-F7+t8E8rja9g9hUCZPvPmw,
romain.perier-Re5JQEeQqe8AvxtiuMwx3w,
amstan-F7+t8E8rja9g9hUCZPvPmw, wxt-TNX95d0MmH7DzftRWevZcw,
zyw-TNX95d0MmH7DzftRWevZcw, jay.xu-TNX95d0MmH7DzftRWevZcw,
olof-nZhT3qVonbNeoWH0uzbU5w, afaerber-l3A5Bk7waGM,
mbrugger-IBi9RG/b67k, chauveau.julien-Re5JQEeQqe8AvxtiuMwx3w,
edubezval-Re5JQEeQqe8AvxtiuMwx3w, sudeep.holla-5wv7dgnIgG8,
shawn.lin-TNX95d0MmH7DzftRWevZcw,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Matthias Brugger
This patch adds basic support for the Tronsmart orion r86 set-top-box.
Signed-off-by: Matthias Brugger <mbrugger-IBi9RG/b67k@public.gmane.org>
---
Changes since v1:
- change memory node to 2GB
- change compatible and file name
- add uart4
- add second led
Documentation/devicetree/bindings/arm/rockchip.txt | 4 +
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3368-orion-r68-meta.dts | 382 +++++++++++++++++++++
3 files changed, 387 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 715d960..1d5c65e0 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -110,3 +110,7 @@ Rockchip platforms device tree bindings
- Rockchip RK3399 evb:
Required root node properties:
- compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
+
+- Tronsmart Orion R68 Meta
+ Required root node properties:
+ - compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 7037a16..87669f6 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
new file mode 100644
index 0000000..8c8671f
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
@@ -0,0 +1,382 @@
+/*
+ * Copyright (c) 2016 Matthias Brugger <mbrugger-IBi9RG/b67k@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "rk3368.dtsi"
+
+/ {
+ model = "Rockchip Orion R68";
+ compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ pinctrl-0 = <&emmc_reset>;
+ pinctrl-names = "default";
+ reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ ext_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ };
+
+ keys: gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_key>;
+
+ button@0 {
+ gpio-key,wakeup = <1>;
+ gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ label = "GPIO Power";
+ linux,code = <116>;
+ };
+ };
+
+ leds: gpio-leds {
+ compatible = "gpio-leds";
+
+ red {
+ gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ label = "orion:red:led";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_ctl>;
+ default-state = "on";
+ };
+
+ blue {
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ label = "orion:blue:led";
+ pinctrl-names = "default";
+ pinctrl-0 = <&stby_pwren>;
+ default-state = "off";
+ };
+ };
+
+ vcc_18: vcc18-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ /* supplies both host and otg */
+ vcc_host: vcc-host-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 4 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vcc_host";
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vccio_sd: vcc-io-sd-regulator {
+ regulator-name= "vccio_sd";
+ gpio = <&gpio0 9 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_sd: vcc-sd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sd";
+ gpio = <&gpio3 11 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_io: vcc-io-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_lan: vcc-lan-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_lan";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_sys: vcc-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vccio_wl: vccio-wl-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vccio_wl";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vdd_10: vdd-10-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_10";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ disable-wp;
+ mmc-pwrseq = <&emmc_pwrseq>;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ status = "okay";
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ phy-supply = <&vcc_lan>;
+ phy-mode = "rgmii";
+ clock_in_out = "input";
+ snps,reset-gpio = <&gpio3 12 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ status = "ok";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: syr827@40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-enable-ramp-delay = <300>;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <8000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ hym8563: hym8563@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ /* rtc_int is not connected */
+ };
+};
+
+&pinctrl {
+ pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+ bias-disable;
+ drive-strength = <8>;
+ };
+
+ pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
+ emmc {
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 19 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 20 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 21 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 22 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 23 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 24 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 25 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
+ };
+
+ emmc-clk {
+ rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
+ };
+
+ emmc-cmd {
+ rockchip,pins = <1 26 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
+ };
+
+ emmc_reset: emmc-reset {
+ rockchip,pins = <2 3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ keys {
+ pwr_key: pwr-key {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ leds {
+ stby_pwren: stby-pwren {
+ rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ led_ctl: led-ctl {
+ rockchip,pins = <3 29 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <2 9 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <2 10 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_cd: sdmmc-cd {
+ rockchip,pins = <2 11 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_bus1: sdmmc-bus1 {
+ rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 6 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 7 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 8 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+ };
+
+ usb {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&saradc {
+ vref-supply = <&vcc_18>;
+ status = "okay";
+};
+
+&sdmmc {
+ clock-frequency = <50000000>;
+ clock-freq-min-max = <400000 50000000>;
+ cap-sd-highspeed;
+ supports-sd;
+ broken-cd;
+ card-detect-delay = <200>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ bus-width = <4>;
+ num-slots = <1>;
+ ignore-pm-notify;
+ keep-power-in-suspend;
+
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_xfer>;
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
--
2.6.6
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH] arm64: dts: rockchip: Add basic support for orion-r68
@ 2016-07-14 12:28 ` Matthias Brugger
0 siblings, 0 replies; 5+ messages in thread
From: Matthias Brugger @ 2016-07-14 12:28 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds basic support for the Tronsmart orion r86 set-top-box.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
---
Changes since v1:
- change memory node to 2GB
- change compatible and file name
- add uart4
- add second led
Documentation/devicetree/bindings/arm/rockchip.txt | 4 +
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3368-orion-r68-meta.dts | 382 +++++++++++++++++++++
3 files changed, 387 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 715d960..1d5c65e0 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -110,3 +110,7 @@ Rockchip platforms device tree bindings
- Rockchip RK3399 evb:
Required root node properties:
- compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
+
+- Tronsmart Orion R68 Meta
+ Required root node properties:
+ - compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 7037a16..87669f6 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
new file mode 100644
index 0000000..8c8671f
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
@@ -0,0 +1,382 @@
+/*
+ * Copyright (c) 2016 Matthias Brugger <mbrugger@suse.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "rk3368.dtsi"
+
+/ {
+ model = "Rockchip Orion R68";
+ compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ pinctrl-0 = <&emmc_reset>;
+ pinctrl-names = "default";
+ reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ ext_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ };
+
+ keys: gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_key>;
+
+ button at 0 {
+ gpio-key,wakeup = <1>;
+ gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ label = "GPIO Power";
+ linux,code = <116>;
+ };
+ };
+
+ leds: gpio-leds {
+ compatible = "gpio-leds";
+
+ red {
+ gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ label = "orion:red:led";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_ctl>;
+ default-state = "on";
+ };
+
+ blue {
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ label = "orion:blue:led";
+ pinctrl-names = "default";
+ pinctrl-0 = <&stby_pwren>;
+ default-state = "off";
+ };
+ };
+
+ vcc_18: vcc18-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ /* supplies both host and otg */
+ vcc_host: vcc-host-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 4 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vcc_host";
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vccio_sd: vcc-io-sd-regulator {
+ regulator-name= "vccio_sd";
+ gpio = <&gpio0 9 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_sd: vcc-sd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sd";
+ gpio = <&gpio3 11 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_io: vcc-io-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_lan: vcc-lan-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_lan";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_sys: vcc-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vccio_wl: vccio-wl-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vccio_wl";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vdd_10: vdd-10-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_10";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ disable-wp;
+ mmc-pwrseq = <&emmc_pwrseq>;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ status = "okay";
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ phy-supply = <&vcc_lan>;
+ phy-mode = "rgmii";
+ clock_in_out = "input";
+ snps,reset-gpio = <&gpio3 12 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ status = "ok";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: syr827 at 40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-enable-ramp-delay = <300>;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <8000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ hym8563: hym8563 at 51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ /* rtc_int is not connected */
+ };
+};
+
+&pinctrl {
+ pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+ bias-disable;
+ drive-strength = <8>;
+ };
+
+ pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
+ emmc {
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 19 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 20 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 21 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 22 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 23 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 24 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 25 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
+ };
+
+ emmc-clk {
+ rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
+ };
+
+ emmc-cmd {
+ rockchip,pins = <1 26 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
+ };
+
+ emmc_reset: emmc-reset {
+ rockchip,pins = <2 3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ keys {
+ pwr_key: pwr-key {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ leds {
+ stby_pwren: stby-pwren {
+ rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ led_ctl: led-ctl {
+ rockchip,pins = <3 29 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <2 9 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <2 10 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_cd: sdmmc-cd {
+ rockchip,pins = <2 11 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_bus1: sdmmc-bus1 {
+ rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 6 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 7 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 8 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+ };
+
+ usb {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&saradc {
+ vref-supply = <&vcc_18>;
+ status = "okay";
+};
+
+&sdmmc {
+ clock-frequency = <50000000>;
+ clock-freq-min-max = <400000 50000000>;
+ cap-sd-highspeed;
+ supports-sd;
+ broken-cd;
+ card-detect-delay = <200>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ bus-width = <4>;
+ num-slots = <1>;
+ ignore-pm-notify;
+ keep-power-in-suspend;
+
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_xfer>;
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
--
2.6.6
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add basic support for orion-r68
2016-07-14 12:28 ` Matthias Brugger
@ 2016-07-15 1:00 ` Shawn Lin
-1 siblings, 0 replies; 5+ messages in thread
From: Shawn Lin @ 2016-07-15 1:00 UTC (permalink / raw)
To: Matthias Brugger, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, heiko, catalin.marinas, will.deacon
Cc: shawn.lin, devicetree, mbrugger, amstan, linux-rockchip,
chauveau.julien, briannorris, dianders, linux-kernel, edubezval,
olof, sudeep.holla, zyw, romain.perier, jay.xu, afaerber,
linux-arm-kernel, wxt
Hi Matthias,
Just some comment for mmc stuff. :)
在 2016/7/14 20:28, Matthias Brugger 写道:
> This patch adds basic support for the Tronsmart orion r86 set-top-box.
>
> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
> ---
> Changes since v1:
> - change memory node to 2GB
> - change compatible and file name
> - add uart4
> - add second led
>
> Documentation/devicetree/bindings/arm/rockchip.txt | 4 +
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3368-orion-r68-meta.dts | 382 +++++++++++++++++++++
> 3 files changed, 387 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
> index 715d960..1d5c65e0 100644
> --- a/Documentation/devicetree/bindings/arm/rockchip.txt
> +++ b/Documentation/devicetree/bindings/arm/rockchip.txt
> @@ -110,3 +110,7 @@ Rockchip platforms device tree bindings
> - Rockchip RK3399 evb:
> Required root node properties:
> - compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
> +
> +- Tronsmart Orion R68 Meta
> + Required root node properties:
> + - compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 7037a16..87669f6 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -1,5 +1,6 @@
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
> new file mode 100644
> index 0000000..8c8671f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
> @@ -0,0 +1,382 @@
> +/*
> + * Copyright (c) 2016 Matthias Brugger <mbrugger@suse.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "rk3368.dtsi"
> +
> +/ {
> + model = "Rockchip Orion R68";
> + compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x80000000>;
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + pinctrl-0 = <&emmc_reset>;
> + pinctrl-names = "default";
> + reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
> + };
> +
> + ext_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <125000000>;
> + clock-output-names = "ext_gmac";
> + };
> +
> + keys: gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwr_key>;
> +
> + button@0 {
> + gpio-key,wakeup = <1>;
> + gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
> + label = "GPIO Power";
> + linux,code = <116>;
> + };
> + };
> +
> + leds: gpio-leds {
> + compatible = "gpio-leds";
> +
> + red {
> + gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + label = "orion:red:led";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_ctl>;
> + default-state = "on";
> + };
> +
> + blue {
> + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
> + label = "orion:blue:led";
> + pinctrl-names = "default";
> + pinctrl-0 = <&stby_pwren>;
> + default-state = "off";
> + };
> + };
> +
> + vcc_18: vcc18-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + /* supplies both host and otg */
> + vcc_host: vcc-host-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 4 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&host_vbus_drv>;
> + regulator-name = "vcc_host";
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vccio_sd: vcc-io-sd-regulator {
> + regulator-name= "vccio_sd";
> + gpio = <&gpio0 9 GPIO_ACTIVE_LOW>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
so, I guess your r68 board won't support sd 3.0?
> + };
> +
> + vcc_sd: vcc-sd-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sd";
> + gpio = <&gpio3 11 GPIO_ACTIVE_LOW>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_io: vcc-io-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcc_lan: vcc-lan-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_lan";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_sys: vcc-sys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vccio_wl: vccio-wl-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vccio_wl";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vdd_10: vdd-10-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_10";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + disable-wp;
> + mmc-pwrseq = <&emmc_pwrseq>;
> + non-removable;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
> + status = "okay";
> +};
> +
> +&gmac {
> + assigned-clocks = <&cru SCLK_MAC>;
> + assigned-clock-parents = <&ext_gmac>;
> + phy-supply = <&vcc_lan>;
> + phy-mode = "rgmii";
> + clock_in_out = "input";
> + snps,reset-gpio = <&gpio3 12 0>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 1000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins>;
> + tx_delay = <0x30>;
> + rx_delay = <0x10>;
> + status = "ok";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + vdd_cpu: syr827@40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu";
> + regulator-enable-ramp-delay = <300>;
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <8000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + hym8563: hym8563@51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "xin32k";
> + /* rtc_int is not connected */
> + };
> +};
> +
> +&pinctrl {
> + pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
> + bias-disable;
> + drive-strength = <8>;
> + };
> +
> + pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
> + bias-pull-up;
> + drive-strength = <8>;
> + };
> +
> + emmc {
> + emmc_bus8: emmc-bus8 {
> + rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 19 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 20 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 21 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 22 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 23 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 24 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 25 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + emmc-clk {
> + rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
> + };
> +
> + emmc-cmd {
> + rockchip,pins = <1 26 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + emmc_reset: emmc-reset {
> + rockchip,pins = <2 3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + keys {
> + pwr_key: pwr-key {
> + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + leds {
> + stby_pwren: stby-pwren {
> + rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + led_ctl: led-ctl {
> + rockchip,pins = <3 29 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdmmc {
> + sdmmc_clk: sdmmc-clk {
> + rockchip,pins = <2 9 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
> + };
> +
> + sdmmc_cmd: sdmmc-cmd {
> + rockchip,pins = <2 10 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_cd: sdmmc-cd {
> + rockchip,pins = <2 11 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_bus1: sdmmc-bus1 {
> + rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_bus4: sdmmc-bus4 {
> + rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <2 6 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <2 7 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <2 8 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> + };
> +
> + usb {
> + host_vbus_drv: host-vbus-drv {
> + rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_18>;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + clock-frequency = <50000000>;
> + clock-freq-min-max = <400000 50000000>;
> + cap-sd-highspeed;
> + supports-sd;
This's not a upstream property.
> + broken-cd;
sdmmc controller of rk3368 isn't broken. Could you remove it?
> + card-detect-delay = <200>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
> + bus-width = <4>;
> + num-slots = <1>;
> + ignore-pm-notify;
ignore-pm-notify is from AOSP but not upstream mmc. You should remove
it.
> + keep-power-in-suspend;
> +
> + vmmc-supply = <&vcc_sd>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_xfer>;
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_otg {
> + status = "okay";
> +};
> +
> +&wdt {
> + status = "okay";
> +};
>
--
Best Regards
Shawn Lin
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH] arm64: dts: rockchip: Add basic support for orion-r68
@ 2016-07-15 1:00 ` Shawn Lin
0 siblings, 0 replies; 5+ messages in thread
From: Shawn Lin @ 2016-07-15 1:00 UTC (permalink / raw)
To: linux-arm-kernel
Hi Matthias,
Just some comment for mmc stuff. :)
? 2016/7/14 20:28, Matthias Brugger ??:
> This patch adds basic support for the Tronsmart orion r86 set-top-box.
>
> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
> ---
> Changes since v1:
> - change memory node to 2GB
> - change compatible and file name
> - add uart4
> - add second led
>
> Documentation/devicetree/bindings/arm/rockchip.txt | 4 +
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3368-orion-r68-meta.dts | 382 +++++++++++++++++++++
> 3 files changed, 387 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
> index 715d960..1d5c65e0 100644
> --- a/Documentation/devicetree/bindings/arm/rockchip.txt
> +++ b/Documentation/devicetree/bindings/arm/rockchip.txt
> @@ -110,3 +110,7 @@ Rockchip platforms device tree bindings
> - Rockchip RK3399 evb:
> Required root node properties:
> - compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
> +
> +- Tronsmart Orion R68 Meta
> + Required root node properties:
> + - compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 7037a16..87669f6 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -1,5 +1,6 @@
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
> new file mode 100644
> index 0000000..8c8671f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
> @@ -0,0 +1,382 @@
> +/*
> + * Copyright (c) 2016 Matthias Brugger <mbrugger@suse.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "rk3368.dtsi"
> +
> +/ {
> + model = "Rockchip Orion R68";
> + compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x80000000>;
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + pinctrl-0 = <&emmc_reset>;
> + pinctrl-names = "default";
> + reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
> + };
> +
> + ext_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <125000000>;
> + clock-output-names = "ext_gmac";
> + };
> +
> + keys: gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwr_key>;
> +
> + button at 0 {
> + gpio-key,wakeup = <1>;
> + gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
> + label = "GPIO Power";
> + linux,code = <116>;
> + };
> + };
> +
> + leds: gpio-leds {
> + compatible = "gpio-leds";
> +
> + red {
> + gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + label = "orion:red:led";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_ctl>;
> + default-state = "on";
> + };
> +
> + blue {
> + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
> + label = "orion:blue:led";
> + pinctrl-names = "default";
> + pinctrl-0 = <&stby_pwren>;
> + default-state = "off";
> + };
> + };
> +
> + vcc_18: vcc18-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + /* supplies both host and otg */
> + vcc_host: vcc-host-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 4 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&host_vbus_drv>;
> + regulator-name = "vcc_host";
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vccio_sd: vcc-io-sd-regulator {
> + regulator-name= "vccio_sd";
> + gpio = <&gpio0 9 GPIO_ACTIVE_LOW>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
so, I guess your r68 board won't support sd 3.0?
> + };
> +
> + vcc_sd: vcc-sd-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sd";
> + gpio = <&gpio3 11 GPIO_ACTIVE_LOW>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_io: vcc-io-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcc_lan: vcc-lan-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_lan";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_sys: vcc-sys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vccio_wl: vccio-wl-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vccio_wl";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vdd_10: vdd-10-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_10";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + disable-wp;
> + mmc-pwrseq = <&emmc_pwrseq>;
> + non-removable;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
> + status = "okay";
> +};
> +
> +&gmac {
> + assigned-clocks = <&cru SCLK_MAC>;
> + assigned-clock-parents = <&ext_gmac>;
> + phy-supply = <&vcc_lan>;
> + phy-mode = "rgmii";
> + clock_in_out = "input";
> + snps,reset-gpio = <&gpio3 12 0>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 1000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins>;
> + tx_delay = <0x30>;
> + rx_delay = <0x10>;
> + status = "ok";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + vdd_cpu: syr827 at 40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu";
> + regulator-enable-ramp-delay = <300>;
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <8000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + hym8563: hym8563 at 51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "xin32k";
> + /* rtc_int is not connected */
> + };
> +};
> +
> +&pinctrl {
> + pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
> + bias-disable;
> + drive-strength = <8>;
> + };
> +
> + pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
> + bias-pull-up;
> + drive-strength = <8>;
> + };
> +
> + emmc {
> + emmc_bus8: emmc-bus8 {
> + rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 19 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 20 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 21 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 22 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 23 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 24 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 25 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + emmc-clk {
> + rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
> + };
> +
> + emmc-cmd {
> + rockchip,pins = <1 26 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + emmc_reset: emmc-reset {
> + rockchip,pins = <2 3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + keys {
> + pwr_key: pwr-key {
> + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + leds {
> + stby_pwren: stby-pwren {
> + rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + led_ctl: led-ctl {
> + rockchip,pins = <3 29 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdmmc {
> + sdmmc_clk: sdmmc-clk {
> + rockchip,pins = <2 9 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
> + };
> +
> + sdmmc_cmd: sdmmc-cmd {
> + rockchip,pins = <2 10 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_cd: sdmmc-cd {
> + rockchip,pins = <2 11 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_bus1: sdmmc-bus1 {
> + rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_bus4: sdmmc-bus4 {
> + rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <2 6 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <2 7 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <2 8 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> + };
> +
> + usb {
> + host_vbus_drv: host-vbus-drv {
> + rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_18>;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + clock-frequency = <50000000>;
> + clock-freq-min-max = <400000 50000000>;
> + cap-sd-highspeed;
> + supports-sd;
This's not a upstream property.
> + broken-cd;
sdmmc controller of rk3368 isn't broken. Could you remove it?
> + card-detect-delay = <200>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
> + bus-width = <4>;
> + num-slots = <1>;
> + ignore-pm-notify;
ignore-pm-notify is from AOSP but not upstream mmc. You should remove
it.
> + keep-power-in-suspend;
> +
> + vmmc-supply = <&vcc_sd>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_xfer>;
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_otg {
> + status = "okay";
> +};
> +
> +&wdt {
> + status = "okay";
> +};
>
--
Best Regards
Shawn Lin
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2016-07-15 1:00 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-07-14 12:28 [PATCH] arm64: dts: rockchip: Add basic support for orion-r68 Matthias Brugger
2016-07-14 12:28 ` Matthias Brugger
2016-07-14 12:28 ` Matthias Brugger
2016-07-15 1:00 ` Shawn Lin
2016-07-15 1:00 ` Shawn Lin
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.