[PATCH v2] dmaengine: idxd: cleanup workqueue config after disabling

[PATCH v2] dmaengine: idxd: cleanup workqueue config after disabling

[Dave Jiang]

After disabling a device, we should clean up the internal state for
the wqs and zero out the configuration registers. Without doing so can cause
issues when the user reprogram the wqs.

Fixes: c52ca478233c ("dmaengine: idxd: add configuration component of driver")
Reported-by: Yixin Zhang <yixin.zhang@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Yixin Zhang <yixin.zhang@intel.com>
---

Rebased against dmaengine fixes branch

 drivers/dma/idxd/device.c |   25 +++++++++++++++++++++++++
 drivers/dma/idxd/idxd.h   |    1 +
 drivers/dma/idxd/sysfs.c  |    5 +++++
 3 files changed, 31 insertions(+)

diff --git a/drivers/dma/idxd/device.c b/drivers/dma/idxd/device.c
index 8d79a8787104..8d2718c585dc 100644
--- a/drivers/dma/idxd/device.c
+++ b/drivers/dma/idxd/device.c
@@ -320,6 +320,31 @@ void idxd_wq_unmap_portal(struct idxd_wq *wq)
 	devm_iounmap(dev, wq->dportal);
 }
 
+void idxd_wq_disable_cleanup(struct idxd_wq *wq)
+{
+	struct idxd_device *idxd = wq->idxd;
+	struct device *dev = &idxd->pdev->dev;
+	int i, wq_offset;
+
+	lockdep_assert_held(&idxd->dev_lock);
+	memset(&wq->wqcfg, 0, sizeof(wq->wqcfg));
+	wq->type = IDXD_WQT_NONE;
+	wq->size = 0;
+	wq->group = NULL;
+	wq->threshold = 0;
+	wq->priority = 0;
+	clear_bit(WQ_FLAG_DEDICATED, &wq->flags);
+	memset(wq->name, 0, WQ_NAME_SIZE);
+
+	for (i = 0; i < 8; i++) {
+		wq_offset = idxd->wqcfg_offset + wq->id * 32 + i * sizeof(u32);
+		iowrite32(0, idxd->reg_base + wq_offset);
+		dev_dbg(dev, "WQ[%d][%d][%#x]: %#x\n",
+			wq->id, i, wq_offset,
+			ioread32(idxd->reg_base + wq_offset));
+	}
+}
+
 /* Device control bits */
 static inline bool idxd_is_enabled(struct idxd_device *idxd)
 {
diff --git a/drivers/dma/idxd/idxd.h b/drivers/dma/idxd/idxd.h
index b8f8a363b4a7..908c8d0ef3ab 100644
--- a/drivers/dma/idxd/idxd.h
+++ b/drivers/dma/idxd/idxd.h
@@ -290,6 +290,7 @@ int idxd_wq_enable(struct idxd_wq *wq);
 int idxd_wq_disable(struct idxd_wq *wq);
 int idxd_wq_map_portal(struct idxd_wq *wq);
 void idxd_wq_unmap_portal(struct idxd_wq *wq);
+void idxd_wq_disable_cleanup(struct idxd_wq *wq);
 
 /* submission */
 int idxd_submit_desc(struct idxd_wq *wq, struct idxd_desc *desc);
diff --git a/drivers/dma/idxd/sysfs.c b/drivers/dma/idxd/sysfs.c
index 052dae5d6ddd..2e2c5082f322 100644
--- a/drivers/dma/idxd/sysfs.c
+++ b/drivers/dma/idxd/sysfs.c
@@ -315,6 +315,11 @@ static int idxd_config_bus_remove(struct device *dev)
 		idxd_unregister_dma_device(idxd);
 		spin_lock_irqsave(&idxd->dev_lock, flags);
 		rc = idxd_device_disable(idxd);
+		for (i = 0; i < idxd->max_wqs; i++) {
+			struct idxd_wq *wq = &idxd->wqs[i];
+
+			idxd_wq_disable_cleanup(wq);
+		}
 		spin_unlock_irqrestore(&idxd->dev_lock, flags);
 		module_put(THIS_MODULE);
 		if (rc < 0)

Re: [PATCH v2] dmaengine: idxd: cleanup workqueue config after disabling

[Vinod Koul]

On 25-06-20, 12:17, Dave Jiang wrote:
> After disabling a device, we should clean up the internal state for
> the wqs and zero out the configuration registers. Without doing so can cause
> issues when the user reprogram the wqs.

Applied, thanks

-- 
~Vinod