* [PATCH RESEND] drm: mxsfb_crtc: Reset the eLCDIF controller
@ 2017-06-05 12:15 Fabio Estevam
0 siblings, 0 replies; 3+ messages in thread
From: Fabio Estevam @ 2017-06-05 12:15 UTC (permalink / raw)
To: seanpaul
Cc: daniel, gustavo.padovan, jani.nikula, marex, dri-devel,
Fabio Estevam, #4 . 11 . x
From: Fabio Estevam <fabio.estevam@nxp.com>
According to the eLCDIF initialization steps listed in the MX6SX
Reference Manual the eLCDIF block reset is mandatory.
Without performing the eLCDIF reset the display shows garbage content
when the kernel boots.
In earlier tests this issue has not been observed because the bootloader
was previously showing a splash screen and the bootloader display driver
does properly implement the eLCDIF reset.
Add the eLCDIF reset to the driver, so that it can operate correctly
independently of the bootloader.
Tested on a imx6sx-sdb board.
Cc: <stable@vger.kernel.org> #4.11.x
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
---
Dear drm-misc maintainers,
Marek suggested that this goes via drm-misc.
Thanks
drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 42 ++++++++++++++++++++++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
index 1144e0c..0abe776 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
@@ -35,6 +35,13 @@
#include "mxsfb_drv.h"
#include "mxsfb_regs.h"
+#define MXS_SET_ADDR 0x4
+#define MXS_CLR_ADDR 0x8
+#define MODULE_CLKGATE BIT(30)
+#define MODULE_SFTRST BIT(31)
+/* 1 second delay should be plenty of time for block reset */
+#define RESET_TIMEOUT 1000000
+
static u32 set_hsync_pulse_width(struct mxsfb_drm_private *mxsfb, u32 val)
{
return (val & mxsfb->devdata->hs_wdth_mask) <<
@@ -159,6 +166,36 @@ static void mxsfb_disable_controller(struct mxsfb_drm_private *mxsfb)
clk_disable_unprepare(mxsfb->clk_disp_axi);
}
+/*
+ * Clear the bit and poll it cleared. This is usually called with
+ * a reset address and mask being either SFTRST(bit 31) or CLKGATE
+ * (bit 30).
+ */
+static int clear_poll_bit(void __iomem *addr, u32 mask)
+{
+ u32 reg;
+
+ writel(mask, addr + MXS_CLR_ADDR);
+ return readl_poll_timeout(addr, reg, !(reg & mask), 0, RESET_TIMEOUT);
+}
+
+static int mxsfb_reset_block(void __iomem *reset_addr)
+{
+ int ret;
+
+ ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
+ if (ret)
+ return ret;
+
+ writel(MODULE_CLKGATE, reset_addr + MXS_CLR_ADDR);
+
+ ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
+ if (ret)
+ return ret;
+
+ return clear_poll_bit(reset_addr, MODULE_CLKGATE);
+}
+
static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
{
struct drm_display_mode *m = &mxsfb->pipe.crtc.state->adjusted_mode;
@@ -173,6 +210,11 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
*/
mxsfb_enable_axi_clk(mxsfb);
+ /* Mandatory eLCDIF reset as per the Reference Manual */
+ err = mxsfb_reset_block(mxsfb->base);
+ if (err)
+ return;
+
/* Clear the FIFOs */
writel(CTRL1_FIFO_CLEAR, mxsfb->base + LCDC_CTRL1 + REG_SET);
--
2.7.4
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH RESEND] drm: mxsfb_crtc: Reset the eLCDIF controller
2017-05-22 20:53 Fabio Estevam
@ 2017-05-28 13:12 ` Fabio Estevam
0 siblings, 0 replies; 3+ messages in thread
From: Fabio Estevam @ 2017-05-28 13:12 UTC (permalink / raw)
To: Daniel Vetter, jani.nikula, Sean Paul
Cc: Marek Vasut, Fabio Estevam, #4 . 11 . x, DRI mailing list
On Mon, May 22, 2017 at 5:53 PM, Fabio Estevam <festevam@gmail.com> wrote:
> From: Fabio Estevam <fabio.estevam@nxp.com>
>
> According to the eLCDIF initialization steps listed in the MX6SX
> Reference Manual the eLCDIF block reset is mandatory.
>
> Without performing the eLCDIF reset the display shows garbage content
> when the kernel boots.
>
> In earlier tests this issue has not been observed because the bootloader
> was previously showing a splash screen and the bootloader display driver
> does properly implement the eLCDIF reset.
>
> Add the eLCDIF reset to the driver, so that it can operate correctly
> independently of the bootloader.
>
> Tested on a imx6sx-sdb board.
>
> Cc: <stable@vger.kernel.org> #4.11.x
> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
> Reviewed-by: Marek Vasut <marex@denx.de>
> ---
> Daniel,
>
> Marek suggested that this goes via drm-misc.
Sean/Jani/Daniel,
Any chance this could go via drm-misc?
Without this change the mxsfb driver is unusable on some platforms.
Thanks
>
> Thanks
>
> drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 42 ++++++++++++++++++++++++++++++++++++++
> 1 file changed, 42 insertions(+)
>
> diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
> index 1144e0c..0abe776 100644
> --- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
> +++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
> @@ -35,6 +35,13 @@
> #include "mxsfb_drv.h"
> #include "mxsfb_regs.h"
>
> +#define MXS_SET_ADDR 0x4
> +#define MXS_CLR_ADDR 0x8
> +#define MODULE_CLKGATE BIT(30)
> +#define MODULE_SFTRST BIT(31)
> +/* 1 second delay should be plenty of time for block reset */
> +#define RESET_TIMEOUT 1000000
> +
> static u32 set_hsync_pulse_width(struct mxsfb_drm_private *mxsfb, u32 val)
> {
> return (val & mxsfb->devdata->hs_wdth_mask) <<
> @@ -159,6 +166,36 @@ static void mxsfb_disable_controller(struct mxsfb_drm_private *mxsfb)
> clk_disable_unprepare(mxsfb->clk_disp_axi);
> }
>
> +/*
> + * Clear the bit and poll it cleared. This is usually called with
> + * a reset address and mask being either SFTRST(bit 31) or CLKGATE
> + * (bit 30).
> + */
> +static int clear_poll_bit(void __iomem *addr, u32 mask)
> +{
> + u32 reg;
> +
> + writel(mask, addr + MXS_CLR_ADDR);
> + return readl_poll_timeout(addr, reg, !(reg & mask), 0, RESET_TIMEOUT);
> +}
> +
> +static int mxsfb_reset_block(void __iomem *reset_addr)
> +{
> + int ret;
> +
> + ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
> + if (ret)
> + return ret;
> +
> + writel(MODULE_CLKGATE, reset_addr + MXS_CLR_ADDR);
> +
> + ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
> + if (ret)
> + return ret;
> +
> + return clear_poll_bit(reset_addr, MODULE_CLKGATE);
> +}
> +
> static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
> {
> struct drm_display_mode *m = &mxsfb->pipe.crtc.state->adjusted_mode;
> @@ -173,6 +210,11 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
> */
> mxsfb_enable_axi_clk(mxsfb);
>
> + /* Mandatory eLCDIF reset as per the Reference Manual */
> + err = mxsfb_reset_block(mxsfb->base);
> + if (err)
> + return;
> +
> /* Clear the FIFOs */
> writel(CTRL1_FIFO_CLEAR, mxsfb->base + LCDC_CTRL1 + REG_SET);
>
> --
> 2.7.4
>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH RESEND] drm: mxsfb_crtc: Reset the eLCDIF controller
@ 2017-05-22 20:53 Fabio Estevam
2017-05-28 13:12 ` Fabio Estevam
0 siblings, 1 reply; 3+ messages in thread
From: Fabio Estevam @ 2017-05-22 20:53 UTC (permalink / raw)
To: daniel; +Cc: marex, Fabio Estevam, #4 . 11 . x, dri-devel
From: Fabio Estevam <fabio.estevam@nxp.com>
According to the eLCDIF initialization steps listed in the MX6SX
Reference Manual the eLCDIF block reset is mandatory.
Without performing the eLCDIF reset the display shows garbage content
when the kernel boots.
In earlier tests this issue has not been observed because the bootloader
was previously showing a splash screen and the bootloader display driver
does properly implement the eLCDIF reset.
Add the eLCDIF reset to the driver, so that it can operate correctly
independently of the bootloader.
Tested on a imx6sx-sdb board.
Cc: <stable@vger.kernel.org> #4.11.x
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
---
Daniel,
Marek suggested that this goes via drm-misc.
Thanks
drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 42 ++++++++++++++++++++++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
index 1144e0c..0abe776 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
@@ -35,6 +35,13 @@
#include "mxsfb_drv.h"
#include "mxsfb_regs.h"
+#define MXS_SET_ADDR 0x4
+#define MXS_CLR_ADDR 0x8
+#define MODULE_CLKGATE BIT(30)
+#define MODULE_SFTRST BIT(31)
+/* 1 second delay should be plenty of time for block reset */
+#define RESET_TIMEOUT 1000000
+
static u32 set_hsync_pulse_width(struct mxsfb_drm_private *mxsfb, u32 val)
{
return (val & mxsfb->devdata->hs_wdth_mask) <<
@@ -159,6 +166,36 @@ static void mxsfb_disable_controller(struct mxsfb_drm_private *mxsfb)
clk_disable_unprepare(mxsfb->clk_disp_axi);
}
+/*
+ * Clear the bit and poll it cleared. This is usually called with
+ * a reset address and mask being either SFTRST(bit 31) or CLKGATE
+ * (bit 30).
+ */
+static int clear_poll_bit(void __iomem *addr, u32 mask)
+{
+ u32 reg;
+
+ writel(mask, addr + MXS_CLR_ADDR);
+ return readl_poll_timeout(addr, reg, !(reg & mask), 0, RESET_TIMEOUT);
+}
+
+static int mxsfb_reset_block(void __iomem *reset_addr)
+{
+ int ret;
+
+ ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
+ if (ret)
+ return ret;
+
+ writel(MODULE_CLKGATE, reset_addr + MXS_CLR_ADDR);
+
+ ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
+ if (ret)
+ return ret;
+
+ return clear_poll_bit(reset_addr, MODULE_CLKGATE);
+}
+
static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
{
struct drm_display_mode *m = &mxsfb->pipe.crtc.state->adjusted_mode;
@@ -173,6 +210,11 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
*/
mxsfb_enable_axi_clk(mxsfb);
+ /* Mandatory eLCDIF reset as per the Reference Manual */
+ err = mxsfb_reset_block(mxsfb->base);
+ if (err)
+ return;
+
/* Clear the FIFOs */
writel(CTRL1_FIFO_CLEAR, mxsfb->base + LCDC_CTRL1 + REG_SET);
--
2.7.4
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2017-06-05 12:15 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-06-05 12:15 [PATCH RESEND] drm: mxsfb_crtc: Reset the eLCDIF controller Fabio Estevam
-- strict thread matches above, loose matches on Subject: below --
2017-05-22 20:53 Fabio Estevam
2017-05-28 13:12 ` Fabio Estevam
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).