From: Jerome Brunet <jbrunet@baylibre.com>
To: Jianxin Pan <jianxin.pan@amlogic.com>,
Kevin Hilman <khilman@baylibre.com>,
linux-amlogic@lists.infradead.org
Cc: devicetree@vger.kernel.org, Hanjie Lin <hanjie.lin@amlogic.com>,
Victor Wan <victor.wan@amlogic.com>,
Jianxin Pan <jianxin.pan@amlogic.com>,
Neil Armstrong <narmstrong@baylibre.com>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
linux-kernel@vger.kernel.org,
Qiufang Dai <qiufang.dai@amlogic.com>,
Rob Herring <robh+dt@kernel.org>, Jian Hu <jian.hu@amlogic.com>,
Xingyu Chen <xingyu.chen@amlogic.com>,
Carlo Caione <carlo@caione.org>, Tao Zeng <tao.zeng@amlogic.com>,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 4/4] arm64: dts: add support for A1 based Amlogic AD401
Date: Tue, 03 Sep 2019 09:30:06 +0200 [thread overview]
Message-ID: <1jef0xrg5d.fsf@starbuckisacylon.baylibre.com> (raw)
In-Reply-To: <1567493475-75451-5-git-send-email-jianxin.pan@amlogic.com>
On Tue 03 Sep 2019 at 02:51, Jianxin Pan <jianxin.pan@amlogic.com> wrote:
> Add basic support for the Amlogic A1 based Amlogic AD401 board:
> which describe components as follows: Reserve Memory, CPU, GIC, IRQ,
> Timer, UART. It's capable of booting up into the serial console.
>
> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
> ---
> arch/arm64/boot/dts/amlogic/Makefile | 1 +
> arch/arm64/boot/dts/amlogic/meson-a1-ad401.dts | 30 ++++++
> arch/arm64/boot/dts/amlogic/meson-a1.dtsi | 121 +++++++++++++++++++++++++
> 3 files changed, 152 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-a1-ad401.dts
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-a1.dtsi
>
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index edbf128..1720c45 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -36,3 +36,4 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-rbox-pro.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-a1-ad401.dts b/arch/arm64/boot/dts/amlogic/meson-a1-ad401.dts
> new file mode 100644
> index 00000000..3c05cc0
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-a1-ad401.dts
> @@ -0,0 +1,30 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-a1.dtsi"
> +
> +/ {
> + compatible = "amlogic,ad401", "amlogic,a1";
> + model = "Amlogic Meson A1 AD401 Development Board";
> +
> + aliases {
> + serial0 = &uart_AO_B;
> + };
Newline here please
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
same
> + memory@0 {
> + device_type = "memory";
> + linux,usable-memory = <0x0 0x0 0x0 0x8000000>;
> + };
> +};
> +
> +&uart_AO_B {
> + status = "okay";
> + /*pinctrl-0 = <&uart_ao_a_pins>;*/
> + /*pinctrl-names = "default";*/
Remove the commented code please
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> new file mode 100644
> index 00000000..b98d648
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> @@ -0,0 +1,121 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +/ {
> + compatible = "amlogic,a1";
> +
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + cpus {
> + #address-cells = <0x2>;
> + #size-cells = <0x0>;
> +
> + cpu0: cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a35";
> + reg = <0x0 0x0>;
> + enable-method = "psci";
> + next-level-cache = <&l2>;
> + };
> +
> + cpu1: cpu@1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a35";
> + reg = <0x0 0x1>;
> + enable-method = "psci";
> + next-level-cache = <&l2>;
> + };
> +
> + l2: l2-cache0 {
> + compatible = "cache";
> + };
> + };
New line here please
With this minor comments adressed, looks good.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
> + psci {
> + compatible = "arm,psci-1.0";
> + method = "smc";
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + linux,cma {
> + compatible = "shared-dma-pool";
> + reusable;
> + size = <0x0 0x800000>;
> + alignment = <0x0 0x400000>;
> + linux,cma-default;
> + };
> + };
> +
> + sm: secure-monitor {
> + compatible = "amlogic,meson-gxbb-sm";
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + uart_AO: serial@fe001c00 {
> + compatible = "amlogic,meson-gx-uart",
> + "amlogic,meson-ao-uart";
> + reg = <0x0 0xfe001c00 0x0 0x18>;
> + interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&xtal>, <&xtal>, <&xtal>;
> + clock-names = "xtal", "pclk", "baud";
> + status = "disabled";
> + };
> +
> + uart_AO_B: serial@fe002000 {
> + compatible = "amlogic,meson-gx-uart",
> + "amlogic,meson-ao-uart";
> + reg = <0x0 0xfe002000 0x0 0x18>;
> + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&xtal>, <&xtal>, <&xtal>;
> + clock-names = "xtal", "pclk", "baud";
> + status = "disabled";
> + };
> +
> + gic: interrupt-controller@ff901000 {
> + compatible = "arm,gic-400";
> + reg = <0x0 0xff901000 0x0 0x1000>,
> + <0x0 0xff902000 0x0 0x2000>,
> + <0x0 0xff904000 0x0 0x2000>,
> + <0x0 0xff906000 0x0 0x2000>;
> + interrupt-controller;
> + interrupts = <GIC_PPI 9
> + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
> + #interrupt-cells = <3>;
> + #address-cells = <0>;
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 13
> + (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14
> + (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11
> + (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10
> + (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + xtal: xtal-clk {
> + compatible = "fixed-clock";
> + clock-frequency = <24000000>;
> + clock-output-names = "xtal";
> + #clock-cells = <0>;
> + };
> +};
> --
> 2.7.4
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
next prev parent reply other threads:[~2019-09-03 7:30 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-09-03 6:51 [PATCH 0/4] arm64: Add basic support for Amlogic A1 SoC Family Jianxin Pan
2019-09-03 6:51 ` [PATCH 1/4] soc: amlogic: meson-gx-socinfo: Add A1 and A113L IDs Jianxin Pan
2019-09-03 7:12 ` Neil Armstrong
2019-09-03 6:51 ` [PATCH 2/4] dt-bindings: arm: amlogic: add A1 bindings Jianxin Pan
2019-09-03 17:38 ` Rob Herring
2019-09-03 6:51 ` [PATCH 3/4] dt-bindings: arm: amlogic: add Amlogic AD401 bindings Jianxin Pan
2019-09-03 17:38 ` Rob Herring
2019-09-03 6:51 ` [PATCH 4/4] arm64: dts: add support for A1 based Amlogic AD401 Jianxin Pan
2019-09-03 7:30 ` Jerome Brunet [this message]
2019-09-03 8:00 ` Jianxin Pan
2019-09-03 7:42 ` Neil Armstrong
2019-09-03 8:16 ` Jianxin Pan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1jef0xrg5d.fsf@starbuckisacylon.baylibre.com \
--to=jbrunet@baylibre.com \
--cc=carlo@caione.org \
--cc=devicetree@vger.kernel.org \
--cc=hanjie.lin@amlogic.com \
--cc=jian.hu@amlogic.com \
--cc=jianxin.pan@amlogic.com \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=martin.blumenstingl@googlemail.com \
--cc=narmstrong@baylibre.com \
--cc=qiufang.dai@amlogic.com \
--cc=robh+dt@kernel.org \
--cc=tao.zeng@amlogic.com \
--cc=victor.wan@amlogic.com \
--cc=xingyu.chen@amlogic.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).