* [PATCH v2 1/1] ARM: dts: imx6x: Add enet2 support for imx6sx-sdb board
@ 2014-09-28 8:40 Fugang Duan
2014-10-14 6:43 ` fugang.duan at freescale.com
2014-10-18 14:18 ` Shawn Guo
0 siblings, 2 replies; 3+ messages in thread
From: Fugang Duan @ 2014-09-28 8:40 UTC (permalink / raw)
To: linux-arm-kernel
Add enet2 support for imx6sx-sdb board, and add the "fsl,imx6q-fec"
compatible for fec2 node to be compatible with the old version.
V2:
Add two fixed regulator for enet phy power supply.
Signed-off-by: Fugang Duan <B38611@freescale.com>
---
arch/arm/boot/dts/imx6sx-sdb.dts | 62 ++++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6sx.dtsi | 2 +-
2 files changed, 63 insertions(+), 1 deletions(-)
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts
index 82d6b34..448489b 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb.dts
@@ -105,6 +105,30 @@
gpio = <&gpio3 27 0>;
enable-active-high;
};
+
+ reg_peri_3v3: regulator at 5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_peri_3v3>;
+ regulator-name = "peri_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_enet_3v3: regulator at 6 {
+ compatible = "regulator-fixed";
+ reg = <6>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet_3v3>;
+ regulator-name = "enet_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
+ };
};
sound {
@@ -133,6 +157,14 @@
&fec1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet1>;
+ phy-supply = <®_enet_3v3>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
phy-mode = "rgmii";
status = "okay";
};
@@ -394,6 +426,30 @@
MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2 0x3081
MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 0x3081
MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081
+ MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M 0x91
+ >;
+ };
+
+ pinctrl_enet_3v3: enet3v3grp {
+ fsl,pins = <
+ MX6SX_PAD_ENET2_COL__GPIO2_IO_6 0x80000000
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC 0xa0b9
+ MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0xa0b1
+ MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0xa0b1
+ MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2 0xa0b1
+ MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3 0xa0b1
+ MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0xa0b1
+ MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK 0x3081
+ MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x3081
+ MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x3081
+ MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2 0x3081
+ MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3 0x3081
+ MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x3081
>;
};
@@ -452,6 +508,12 @@
>;
};
+ pinctrl_peri_3v3: peri3v3grp {
+ fsl,pins = <
+ MX6SX_PAD_QSPI1A_DATA0__GPIO4_IO_16 0x80000000
+ >;
+ };
+
pinctrl_pwm3: pwm3grp-1 {
fsl,pins = <
MX6SX_PAD_SD1_DATA2__PWM3_OUT 0x110b0
diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi
index 888dd76..5a36053 100644
--- a/arch/arm/boot/dts/imx6sx.dtsi
+++ b/arch/arm/boot/dts/imx6sx.dtsi
@@ -875,7 +875,7 @@
};
fec2: ethernet@021b4000 {
- compatible = "fsl,imx6sx-fec";
+ compatible = "fsl,imx6sx-fec", "fsl,imx6q-fec";
reg = <0x021b4000 0x4000>;
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
--
1.7.8
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH v2 1/1] ARM: dts: imx6x: Add enet2 support for imx6sx-sdb board
2014-09-28 8:40 [PATCH v2 1/1] ARM: dts: imx6x: Add enet2 support for imx6sx-sdb board Fugang Duan
@ 2014-10-14 6:43 ` fugang.duan at freescale.com
2014-10-18 14:18 ` Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: fugang.duan at freescale.com @ 2014-10-14 6:43 UTC (permalink / raw)
To: linux-arm-kernel
Hi, Shawn,
How about the patch V2 ?
From: Fugang Duan <b38611@freescale.com> Sent: Sunday, September 28, 2014 4:41 PM
>To: Guo Shawn-R65073
>Cc: linux-arm-kernel at lists.infradead.org; b20596 at solarflare.com; Gong
>Yibin-B38343; Duan Fugang-B38611; shawn.guo at linaro.org;
>kernel at pengutronix.de
>Subject: [PATCH v2 1/1] ARM: dts: imx6x: Add enet2 support for imx6sx-sdb
>board
>
>Add enet2 support for imx6sx-sdb board, and add the "fsl,imx6q-fec"
>compatible for fec2 node to be compatible with the old version.
>
>V2:
>Add two fixed regulator for enet phy power supply.
>
>Signed-off-by: Fugang Duan <B38611@freescale.com>
>---
> arch/arm/boot/dts/imx6sx-sdb.dts | 62
>++++++++++++++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6sx.dtsi | 2 +-
> 2 files changed, 63 insertions(+), 1 deletions(-)
>
>diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-
>sdb.dts
>index 82d6b34..448489b 100644
>--- a/arch/arm/boot/dts/imx6sx-sdb.dts
>+++ b/arch/arm/boot/dts/imx6sx-sdb.dts
>@@ -105,6 +105,30 @@
> gpio = <&gpio3 27 0>;
> enable-active-high;
> };
>+
>+ reg_peri_3v3: regulator at 5 {
>+ compatible = "regulator-fixed";
>+ reg = <5>;
>+ pinctrl-names = "default";
>+ pinctrl-0 = <&pinctrl_peri_3v3>;
>+ regulator-name = "peri_3v3";
>+ regulator-min-microvolt = <3300000>;
>+ regulator-max-microvolt = <3300000>;
>+ gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
>+ enable-active-high;
>+ regulator-always-on;
>+ };
>+
>+ reg_enet_3v3: regulator at 6 {
>+ compatible = "regulator-fixed";
>+ reg = <6>;
>+ pinctrl-names = "default";
>+ pinctrl-0 = <&pinctrl_enet_3v3>;
>+ regulator-name = "enet_3v3";
>+ regulator-min-microvolt = <3300000>;
>+ regulator-max-microvolt = <3300000>;
>+ gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
>+ };
> };
>
> sound {
>@@ -133,6 +157,14 @@
> &fec1 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_enet1>;
>+ phy-supply = <®_enet_3v3>;
>+ phy-mode = "rgmii";
>+ status = "okay";
>+};
>+
>+&fec2 {
>+ pinctrl-names = "default";
>+ pinctrl-0 = <&pinctrl_enet2>;
> phy-mode = "rgmii";
> status = "okay";
> };
>@@ -394,6 +426,30 @@
> MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2 0x3081
> MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 0x3081
> MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081
>+ MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M 0x91
>+ >;
>+ };
>+
>+ pinctrl_enet_3v3: enet3v3grp {
>+ fsl,pins = <
>+ MX6SX_PAD_ENET2_COL__GPIO2_IO_6
> 0x80000000
>+ >;
>+ };
>+
>+ pinctrl_enet2: enet2grp {
>+ fsl,pins = <
>+ MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC 0xa0b9
>+ MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0xa0b1
>+ MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0xa0b1
>+ MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2 0xa0b1
>+ MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3 0xa0b1
>+ MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0xa0b1
>+ MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK 0x3081
>+ MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x3081
>+ MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x3081
>+ MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2 0x3081
>+ MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3 0x3081
>+ MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x3081
> >;
> };
>
>@@ -452,6 +508,12 @@
> >;
> };
>
>+ pinctrl_peri_3v3: peri3v3grp {
>+ fsl,pins = <
>+ MX6SX_PAD_QSPI1A_DATA0__GPIO4_IO_16 0x80000000
>+ >;
>+ };
>+
> pinctrl_pwm3: pwm3grp-1 {
> fsl,pins = <
> MX6SX_PAD_SD1_DATA2__PWM3_OUT 0x110b0 diff --git
>a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi index
>888dd76..5a36053 100644
>--- a/arch/arm/boot/dts/imx6sx.dtsi
>+++ b/arch/arm/boot/dts/imx6sx.dtsi
>@@ -875,7 +875,7 @@
> };
>
> fec2: ethernet at 021b4000 {
>- compatible = "fsl,imx6sx-fec";
>+ compatible = "fsl,imx6sx-fec", "fsl,imx6q-fec";
> reg = <0x021b4000 0x4000>;
> interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
>--
>1.7.8
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH v2 1/1] ARM: dts: imx6x: Add enet2 support for imx6sx-sdb board
2014-09-28 8:40 [PATCH v2 1/1] ARM: dts: imx6x: Add enet2 support for imx6sx-sdb board Fugang Duan
2014-10-14 6:43 ` fugang.duan at freescale.com
@ 2014-10-18 14:18 ` Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Shawn Guo @ 2014-10-18 14:18 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Sep 28, 2014 at 04:40:36PM +0800, Fugang Duan wrote:
> Add enet2 support for imx6sx-sdb board, and add the "fsl,imx6q-fec"
> compatible for fec2 node to be compatible with the old version.
>
> V2:
> Add two fixed regulator for enet phy power supply.
>
> Signed-off-by: Fugang Duan <B38611@freescale.com>
Applied, thanks.
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2014-10-18 14:18 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-09-28 8:40 [PATCH v2 1/1] ARM: dts: imx6x: Add enet2 support for imx6sx-sdb board Fugang Duan
2014-10-14 6:43 ` fugang.duan at freescale.com
2014-10-18 14:18 ` Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).