From: "Konstantin Sudakov" <k.sudakov@integrasources.com>
To: "Paul Kocialkowski" <paul.kocialkowski@bootlin.com>,
"Maxime Ripard" <maxime.ripard@bootlin.com>
Cc: bbrezillon@kernel.org, "Sam Ravnborg" <sam@ravnborg.org>,
"Maarten Lankhorst" <maarten.lankhorst@linux.intel.com>,
dri-devel@lists.freedesktop.org, "Chen-Yu Tsai" <wens@csie.org>,
"Sean Paul" <seanpaul@chromium.org>,
"Thomas Petazzoni" <thomas.petazzoni@bootlin.com>,
"Jagan Teki" <jagan@openedev.com>,
linux-arm-kernel@lists.infradead.org
Subject: Re[2]: [PATCH v3 8/8] drm/panel: Add Ronbo RB070D30 panel
Date: Thu, 14 Feb 2019 14:07:45 +0300 [thread overview]
Message-ID: <1550142465.930628529@f521.i.mail.ru> (raw)
In-Reply-To: <25f4beadd3088b3fbb2751f120e4216969301136.camel@bootlin.com>
Hello Paul, Maxime. I suggest the patch to fix it.
diff --no-dereference -u -r -N linux-5.0-rc6_origin/Documentation/devicetree/bindings/display/panel/ronbo,rb070d30.txt linux-5.0-rc6/Documentation/devicetree/bindings/display/panel/ronbo,rb070d30.txt
--- linux-5.0-rc6_origin/Documentation/devicetree/bindings/display/panel/ronbo,rb070d30.txt 1970-01-01 07:00:00.000000000 +0700
+++ linux-5.0-rc6/Documentation/devicetree/bindings/display/panel/ronbo,rb070d30.txt 2019-02-14 18:00:06.613795857 +0700
@@ -0,0 +1,23 @@
+Ronbo RB070D30N01A MIPI-DSI panel
+
+Required properties:
+ - compatible: must be "ronbo,rb070d30"
+ - reg: DSI virtual channel used by that screen
+ - vcc-lcd-supply: phandle to the power regulator
+ - backlight: phandle to the backlight used
+ - reset-gpios: a GPIO phandle for the reset pin
+ - power-gpios: a GPIO phandle for the power pin
+ - updn-gpios: a GPIO phandle for the updn pin (vertical flip)
+ - shlr-gpios: a GPIO phandle for the shlr pin (horizontal flip)
+
+Example:
+panel@0 {
+ compatible = "ronbo,rb070d30";
+ reg = <0>;
+ vcc-lcd-supply = <®_display>;
+ backlight = <&backlight>;
+ reset-gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL01 */
+ power-gpios = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL02 */
+ updn-gpios = <&r_pio 0 3 GPIO_ACTIVE_HIGH>; /* PL03 */
+ shlr-gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>; /* PL04 */
+};
diff --no-dereference -u -r -N linux-5.0-rc6_origin/Documentation/devicetree/bindings/vendor-prefixes.txt linux-5.0-rc6/Documentation/devicetree/bindings/vendor-prefixes.txt
--- linux-5.0-rc6_origin/Documentation/devicetree/bindings/vendor-prefixes.txt 2019-02-11 05:42:20.000000000 +0700
+++ linux-5.0-rc6/Documentation/devicetree/bindings/vendor-prefixes.txt 2019-02-14 17:39:46.667994322 +0700
@@ -334,6 +334,7 @@
riscv RISC-V Foundation
rockchip Fuzhou Rockchip Electronics Co., Ltd
rohm ROHM Semiconductor Co., Ltd
+ronbo Ronbo Electronics Ltd.
roofull Shenzhen Roofull Technology Co, Ltd
samsung Samsung Semiconductor
samtec Samtec/Softing company
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-02-14 11:08 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-02-11 14:41 [PATCH v3 0/8] drm/sun4i: dsi: Add burst mode support Maxime Ripard
2019-02-11 14:41 ` [PATCH v3 1/8] drm/sun4i: dsi: Restrict DSI tcon clock divider Maxime Ripard
2019-02-11 14:41 ` [PATCH v3 2/8] drm/sun4i: dsi: Change the start delay calculation Maxime Ripard
2019-02-12 15:28 ` Paul Kocialkowski
2019-02-12 15:45 ` Maxime Ripard
2019-02-11 14:41 ` [PATCH v3 3/8] drm/sun4i: dsi: Enforce boundaries on the start delay Maxime Ripard
2019-02-12 15:30 ` Paul Kocialkowski
2019-02-14 9:21 ` Maxime Ripard
2019-02-11 14:41 ` [PATCH v3 4/8] drm/sun4i: dsi: Fix front vs back porch calculation Maxime Ripard
2019-02-12 15:41 ` Paul Kocialkowski
2019-02-11 14:41 ` [PATCH v3 5/8] drm/sun4i: dsi: Fix DRQ calculation Maxime Ripard
2019-02-13 14:33 ` Paul Kocialkowski
2019-02-14 9:23 ` Maxime Ripard
2019-02-11 14:41 ` [PATCH v3 6/8] drm/sun4i: dsi: Rework a bit the hblk calculation Maxime Ripard
2019-02-13 14:41 ` Paul Kocialkowski
2019-02-11 14:41 ` [PATCH v3 7/8] drm/sun4i: dsi: Add burst support Maxime Ripard
2019-02-13 14:36 ` Paul Kocialkowski
2019-02-14 9:15 ` Maxime Ripard
2019-02-11 14:41 ` [PATCH v3 8/8] drm/panel: Add Ronbo RB070D30 panel Maxime Ripard
2019-02-11 15:13 ` Sam Ravnborg
2019-02-13 14:26 ` Paul Kocialkowski
2019-02-14 11:07 ` Konstantin Sudakov [this message]
2019-02-12 10:32 ` [PATCH v3 0/8] drm/sun4i: dsi: Add burst mode support Jagan Teki
2019-02-15 14:12 ` Maxime Ripard
[not found] ` <CAMty3ZAA90-fHPADJSE3ht9CiYWA3yBoyEy7wVv9=6C5JiaTVw@mail.gmail.com>
2019-02-15 17:07 ` Jagan Teki
2019-02-18 8:26 ` Paul Kocialkowski
2019-02-18 10:31 ` Jagan Teki
2019-02-20 16:35 ` Maxime Ripard
2019-02-26 6:48 ` Jagan Teki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1550142465.930628529@f521.i.mail.ru \
--to=k.sudakov@integrasources.com \
--cc=bbrezillon@kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=jagan@openedev.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=maarten.lankhorst@linux.intel.com \
--cc=maxime.ripard@bootlin.com \
--cc=paul.kocialkowski@bootlin.com \
--cc=sam@ravnborg.org \
--cc=seanpaul@chromium.org \
--cc=thomas.petazzoni@bootlin.com \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).