[PATCH v3 0/6] soc: xilinx: vcu: provide interfaces for other drivers

[PATCH v3 0/6] soc: xilinx: vcu: provide interfaces for other drivers

[Michael Tretter]

Hello,

This is v3 of the series to add interfaces that can be used by other drivers
to the xlnx_vcu driver. See [0] for the full motivation for this patch series.

v2 accidentally contained the unused xvcu_reset() function. I removed the
function again.

Michael

[0] https://lore.kernel.org/linux-arm-kernel/20200317094115.15896-1-m.tretter@pengutronix.de/

Changelog:

v2 -> v3:
- drop unused xvcu_reset() function

v1 -> v2:
- drop custom select for syscon
- unregister registered clocks on driver remove


Michael Tretter (6):
  soc: xilinx: vcu: drop useless success message
  ARM: dts: define indexes for output clocks
  soc: xilinx: vcu: implement clock provider for output clocks
  dt-bindings: soc: xlnx: extract xlnx,vcu-settings to separate binding
  soc: xilinx: vcu: use vcu-settings syscon registers
  soc: xilinx: vcu: add missing register NUM_CORE

 .../soc/xilinx/xlnx,vcu-settings.yaml         |  34 ++++
 .../bindings/soc/xilinx/xlnx,vcu.txt          |   9 +-
 drivers/soc/xilinx/Kconfig                    |   3 +-
 drivers/soc/xilinx/xlnx_vcu.c                 | 158 ++++++++++++------
 include/dt-bindings/clock/xlnx-vcu.h          |  15 ++
 include/linux/mfd/syscon/xlnx-vcu.h           |  39 +++++
 6 files changed, 200 insertions(+), 58 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/soc/xilinx/xlnx,vcu-settings.yaml
 create mode 100644 include/dt-bindings/clock/xlnx-vcu.h
 create mode 100644 include/linux/mfd/syscon/xlnx-vcu.h

-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 1/6] soc: xilinx: vcu: drop useless success message

[Michael Tretter]

The message that the driver was successfully probed only adds useless
noise. Drop the message.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
---
Changelog:

v2 -> v3:
- none

v1 -> v2:
- none
---
 drivers/soc/xilinx/xlnx_vcu.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/soc/xilinx/xlnx_vcu.c b/drivers/soc/xilinx/xlnx_vcu.c
index a3aa40996f13..dcd8e7824b06 100644
--- a/drivers/soc/xilinx/xlnx_vcu.c
+++ b/drivers/soc/xilinx/xlnx_vcu.c
@@ -571,8 +571,6 @@ static int xvcu_probe(struct platform_device *pdev)
 
 	dev_set_drvdata(&pdev->dev, xvcu);
 
-	dev_info(&pdev->dev, "%s: Probed successfully\n", __func__);
-
 	return 0;
 
 error_pll_ref:
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 2/6] ARM: dts: define indexes for output clocks

[Michael Tretter]

The VCU System-Level Control provides 4 clocks. Defined indexes for
these clocks.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
---
Changelog:

v2 -> v3:
- none

v1 -> v2:
- none
---
 include/dt-bindings/clock/xlnx-vcu.h | 15 +++++++++++++++
 1 file changed, 15 insertions(+)
 create mode 100644 include/dt-bindings/clock/xlnx-vcu.h

diff --git a/include/dt-bindings/clock/xlnx-vcu.h b/include/dt-bindings/clock/xlnx-vcu.h
new file mode 100644
index 000000000000..f2a5ea9c4155
--- /dev/null
+++ b/include/dt-bindings/clock/xlnx-vcu.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2020 Pengutronix, Michael Tretter <kernel@pengutronix.de>
+ */
+
+#ifndef _DT_BINDINGS_CLOCK_XLNX_VCU_H
+#define _DT_BINDINGS_CLOCK_XLNX_VCU_H
+
+#define CLK_XVCU_ENC_CORE		0
+#define CLK_XVCU_ENC_MCU		1
+#define CLK_XVCU_DEC_CORE		2
+#define CLK_XVCU_DEC_MCU		3
+#define CLK_XVCU_MAX			4
+
+#endif /* _DT_BINDINGS_CLOCK_XLNX_VCU_H */
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 3/6] soc: xilinx: vcu: implement clock provider for output clocks

[Michael Tretter]

The VCU System-Level Control uses an internal PLL to drive the core and
MCU clock for the allegro encoder and decoder based on an external PL
clock.

In order be able to ensure that the clocks are enabled and to get their
rate from other drivers, the module must implement a clock provider and
register the clocks at the common clock framework. Other drivers are
then able to access the clock via devicetree bindings.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
---
Changelog:

v2 -> v3:
- drop unused xvcu_reset function

v1 -> v2:
- unregister registered clocks when removing the driver
---
 drivers/soc/xilinx/Kconfig    |  2 +-
 drivers/soc/xilinx/xlnx_vcu.c | 64 +++++++++++++++++++++++++++++++++--
 2 files changed, 63 insertions(+), 3 deletions(-)

diff --git a/drivers/soc/xilinx/Kconfig b/drivers/soc/xilinx/Kconfig
index 223f1f9d0922..331f124902e8 100644
--- a/drivers/soc/xilinx/Kconfig
+++ b/drivers/soc/xilinx/Kconfig
@@ -3,7 +3,7 @@ menu "Xilinx SoC drivers"
 
 config XILINX_VCU
 	tristate "Xilinx VCU logicoreIP Init"
-	depends on HAS_IOMEM
+	depends on HAS_IOMEM && COMMON_CLK
 	help
 	  Provides the driver to enable and disable the isolation between the
 	  processing system and programmable logic part by using the logicoreIP
diff --git a/drivers/soc/xilinx/xlnx_vcu.c b/drivers/soc/xilinx/xlnx_vcu.c
index dcd8e7824b06..03bf252737aa 100644
--- a/drivers/soc/xilinx/xlnx_vcu.c
+++ b/drivers/soc/xilinx/xlnx_vcu.c
@@ -7,6 +7,7 @@
  * Contacts   Dhaval Shah <dshah@xilinx.com>
  */
 #include <linux/clk.h>
+#include <linux/clk-provider.h>
 #include <linux/device.h>
 #include <linux/errno.h>
 #include <linux/io.h>
@@ -14,6 +15,8 @@
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 
+#include <dt-bindings/clock/xlnx-vcu.h>
+
 /* Address map for different registers implemented in the VCU LogiCORE IP. */
 #define VCU_ECODER_ENABLE		0x00
 #define VCU_DECODER_ENABLE		0x04
@@ -108,7 +111,9 @@ struct xvcu_device {
 	struct clk *aclk;
 	void __iomem *logicore_reg_ba;
 	void __iomem *vcu_slcr_ba;
+	struct clk_onecell_data clk_data;
 	u32 coreclk;
+	u32 mcuclk;
 };
 
 /**
@@ -375,10 +380,10 @@ static int xvcu_set_vcu_pll_info(struct xvcu_device *xvcu)
 	}
 
 	xvcu->coreclk = pll_clk / divisor_core;
-	mcuclk = pll_clk / divisor_mcu;
+	xvcu->mcuclk = pll_clk / divisor_mcu;
 	dev_dbg(xvcu->dev, "Actual Ref clock freq is %uHz\n", refclk);
 	dev_dbg(xvcu->dev, "Actual Core clock freq is %uHz\n", xvcu->coreclk);
-	dev_dbg(xvcu->dev, "Actual Mcu clock freq is %uHz\n", mcuclk);
+	dev_dbg(xvcu->dev, "Actual Mcu clock freq is %uHz\n", xvcu->mcuclk);
 
 	vcu_pll_ctrl &= ~(VCU_PLL_CTRL_FBDIV_MASK << VCU_PLL_CTRL_FBDIV_SHIFT);
 	vcu_pll_ctrl |= (found->fbdiv & VCU_PLL_CTRL_FBDIV_MASK) <<
@@ -485,6 +490,51 @@ static int xvcu_set_pll(struct xvcu_device *xvcu)
 	return -ETIMEDOUT;
 }
 
+static int xvcu_register_clock_provider(struct xvcu_device *xvcu)
+{
+	struct device *dev = xvcu->dev;
+	const char *parent_name = __clk_get_name(xvcu->pll_ref);
+	struct clk_onecell_data *data = &xvcu->clk_data;
+	struct clk **clks;
+	size_t num_clks = CLK_XVCU_MAX;
+
+	clks = devm_kcalloc(dev, num_clks, sizeof(*clks), GFP_KERNEL);
+	if (!clks)
+		return -ENOMEM;
+
+	data->clk_num = num_clks;
+	data->clks = clks;
+
+	clks[CLK_XVCU_ENC_CORE] =
+		clk_register_fixed_rate(dev, "venc_core_clk",
+					parent_name, 0, xvcu->coreclk);
+	clks[CLK_XVCU_ENC_MCU] =
+		clk_register_fixed_rate(dev, "venc_mcu_clk",
+					parent_name, 0, xvcu->mcuclk);
+	clks[CLK_XVCU_DEC_CORE] =
+		clk_register_fixed_rate(dev, "vdec_core_clk",
+					parent_name, 0, xvcu->coreclk);
+	clks[CLK_XVCU_DEC_MCU] =
+		clk_register_fixed_rate(dev, "vdec_mcu_clk",
+					parent_name, 0, xvcu->mcuclk);
+
+	return of_clk_add_provider(dev->of_node, of_clk_src_onecell_get, data);
+}
+
+static void xvcu_unregister_clock_provider(struct xvcu_device *xvcu)
+{
+	struct device *dev = xvcu->dev;
+	struct clk_onecell_data *data = &xvcu->clk_data;
+	struct clk **clks = data->clks;
+
+	of_clk_del_provider(dev->of_node);
+
+	clk_unregister_fixed_rate(clks[CLK_XVCU_DEC_MCU]);
+	clk_unregister_fixed_rate(clks[CLK_XVCU_DEC_CORE]);
+	clk_unregister_fixed_rate(clks[CLK_XVCU_ENC_MCU]);
+	clk_unregister_fixed_rate(clks[CLK_XVCU_ENC_CORE]);
+}
+
 /**
  * xvcu_probe - Probe existence of the logicoreIP
  *			and initialize PLL
@@ -569,10 +619,18 @@ static int xvcu_probe(struct platform_device *pdev)
 		goto error_pll_ref;
 	}
 
+	ret = xvcu_register_clock_provider(xvcu);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to register clock provider\n");
+		goto error_clk_provider;
+	}
+
 	dev_set_drvdata(&pdev->dev, xvcu);
 
 	return 0;
 
+error_clk_provider:
+	xvcu_unregister_clock_provider(xvcu);
 error_pll_ref:
 	clk_disable_unprepare(xvcu->pll_ref);
 error_aclk:
@@ -596,6 +654,8 @@ static int xvcu_remove(struct platform_device *pdev)
 	if (!xvcu)
 		return -ENODEV;
 
+	xvcu_unregister_clock_provider(xvcu);
+
 	/* Add the the Gasket isolation and put the VCU in reset. */
 	xvcu_write(xvcu->logicore_reg_ba, VCU_GASKET_INIT, 0);
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 4/6] dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding

[Michael Tretter]

The xlnx,vcu binding comprises two adjacent register banks:

The first register bank ("vcu_slcr") contains registers for setting the
clocks of the vcu and controlling the performance monitors. The second
bank ("logicoreip") contains the configuration settings of the video codec
unit, which are set before synthesizing the bitstream.

Drivers that drive the actual video codec unit need to to read the
registers from the logicoreip register bank for configuring the vcu
firmware.

As logicoreip is a too generic name for this register bank, use
"vcu-settings" as a binding name, because the register bank basically
provides the configuration settings of the VCU.

Therefore, add the vcu-settings binding to provide a syscon interface
for other drivers to read these registers.

The alternative would have been to merge the two register banks of the
xlnx,vcu binding into one register bank and make xlnx,vcu provide a
syscon interface, but that would lead to more incompatibility than
making second register bank of xlnx,vcu optional.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
---
Changelog:

v2 -> v3:
- none

v1 -> v2:
- drop custom select for syscon
---
 .../soc/xilinx/xlnx,vcu-settings.yaml         | 34 +++++++++++++++++++
 .../bindings/soc/xilinx/xlnx,vcu.txt          |  9 ++---
 2 files changed, 36 insertions(+), 7 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/soc/xilinx/xlnx,vcu-settings.yaml

diff --git a/Documentation/devicetree/bindings/soc/xilinx/xlnx,vcu-settings.yaml b/Documentation/devicetree/bindings/soc/xilinx/xlnx,vcu-settings.yaml
new file mode 100644
index 000000000000..378d0ced43c8
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/xilinx/xlnx,vcu-settings.yaml
@@ -0,0 +1,34 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/xilinx/xlnx,vcu-settings.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx VCU Settings
+
+maintainers:
+  - Michael Tretter <kernel@pengutronix.de>
+
+description: |
+  The Xilinx VCU Settings provides information about the configuration of the
+  video codec unit.
+
+properties:
+  compatible:
+    items:
+      - const: xlnx,vcu-settings
+      - const: syscon
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    xlnx_vcu: vcu@a0041000 {
+          compatible = "xlnx,vcu-settings", "syscon";
+          reg = <0x0 0xa0041000 0x0 0x1000>;
+    };
diff --git a/Documentation/devicetree/bindings/soc/xilinx/xlnx,vcu.txt b/Documentation/devicetree/bindings/soc/xilinx/xlnx,vcu.txt
index 6786d6715df0..2417b13ba468 100644
--- a/Documentation/devicetree/bindings/soc/xilinx/xlnx,vcu.txt
+++ b/Documentation/devicetree/bindings/soc/xilinx/xlnx,vcu.txt
@@ -12,10 +12,7 @@ Required properties:
 - compatible: shall be one of:
 	"xlnx,vcu"
 	"xlnx,vcu-logicoreip-1.0"
-- reg, reg-names: There are two sets of registers need to provide.
-	1. vcu slcr
-	2. Logicore
-	reg-names should contain name for the each register sequence.
+- reg : The base offset and size of the VCU_PL_SLCR register space.
 - clocks: phandle for aclk and pll_ref clocksource
 - clock-names: The identification string, "aclk", is always required for
    the axi clock. "pll_ref" is required for pll.
@@ -23,9 +20,7 @@ Example:
 
 	xlnx_vcu: vcu@a0040000 {
 		compatible = "xlnx,vcu-logicoreip-1.0";
-		reg = <0x0 0xa0040000 0x0 0x1000>,
-			 <0x0 0xa0041000 0x0 0x1000>;
-		reg-names = "vcu_slcr", "logicore";
+		reg = <0x0 0xa0040000 0x0 0x1000>;
 		clocks = <&si570_1>, <&clkc 71>;
 		clock-names = "pll_ref", "aclk";
 	};
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 5/6] soc: xilinx: vcu: use vcu-settings syscon registers

[Michael Tretter]

Switch the "logicoreip" registers to the new xlnx,vcu-settings binding
to be able to read the settings if the settings are specified in a
separate device tree node that is shared with other drivers.

If the driver is not able to find a node with the new binding, fall back
to check for the logicore register bank to be backwards compatible.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
---
Changelog:

v2 -> v3:
- none

v1 -> v2:
- none
---
 drivers/soc/xilinx/Kconfig          |  1 +
 drivers/soc/xilinx/xlnx_vcu.c       | 94 ++++++++++++++---------------
 include/linux/mfd/syscon/xlnx-vcu.h | 38 ++++++++++++
 3 files changed, 86 insertions(+), 47 deletions(-)
 create mode 100644 include/linux/mfd/syscon/xlnx-vcu.h

diff --git a/drivers/soc/xilinx/Kconfig b/drivers/soc/xilinx/Kconfig
index 331f124902e8..928e6c0e4926 100644
--- a/drivers/soc/xilinx/Kconfig
+++ b/drivers/soc/xilinx/Kconfig
@@ -4,6 +4,7 @@ menu "Xilinx SoC drivers"
 config XILINX_VCU
 	tristate "Xilinx VCU logicoreIP Init"
 	depends on HAS_IOMEM && COMMON_CLK
+	select REGMAP_MMIO
 	help
 	  Provides the driver to enable and disable the isolation between the
 	  processing system and programmable logic part by using the logicoreIP
diff --git a/drivers/soc/xilinx/xlnx_vcu.c b/drivers/soc/xilinx/xlnx_vcu.c
index 03bf252737aa..ea4ae1e91fb7 100644
--- a/drivers/soc/xilinx/xlnx_vcu.c
+++ b/drivers/soc/xilinx/xlnx_vcu.c
@@ -11,42 +11,15 @@
 #include <linux/device.h>
 #include <linux/errno.h>
 #include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/xlnx-vcu.h>
 #include <linux/module.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
+#include <linux/regmap.h>
 
 #include <dt-bindings/clock/xlnx-vcu.h>
 
-/* Address map for different registers implemented in the VCU LogiCORE IP. */
-#define VCU_ECODER_ENABLE		0x00
-#define VCU_DECODER_ENABLE		0x04
-#define VCU_MEMORY_DEPTH		0x08
-#define VCU_ENC_COLOR_DEPTH		0x0c
-#define VCU_ENC_VERTICAL_RANGE		0x10
-#define VCU_ENC_FRAME_SIZE_X		0x14
-#define VCU_ENC_FRAME_SIZE_Y		0x18
-#define VCU_ENC_COLOR_FORMAT		0x1c
-#define VCU_ENC_FPS			0x20
-#define VCU_MCU_CLK			0x24
-#define VCU_CORE_CLK			0x28
-#define VCU_PLL_BYPASS			0x2c
-#define VCU_ENC_CLK			0x30
-#define VCU_PLL_CLK			0x34
-#define VCU_ENC_VIDEO_STANDARD		0x38
-#define VCU_STATUS			0x3c
-#define VCU_AXI_ENC_CLK			0x40
-#define VCU_AXI_DEC_CLK			0x44
-#define VCU_AXI_MCU_CLK			0x48
-#define VCU_DEC_VIDEO_STANDARD		0x4c
-#define VCU_DEC_FRAME_SIZE_X		0x50
-#define VCU_DEC_FRAME_SIZE_Y		0x54
-#define VCU_DEC_FPS			0x58
-#define VCU_BUFFER_B_FRAME		0x5c
-#define VCU_WPP_EN			0x60
-#define VCU_PLL_CLK_DEC			0x64
-#define VCU_GASKET_INIT			0x74
-#define VCU_GASKET_VALUE		0x03
-
 /* vcu slcr registers, bitmask and shift */
 #define VCU_PLL_CTRL			0x24
 #define VCU_PLL_CTRL_RESET_MASK		0x01
@@ -109,13 +82,22 @@ struct xvcu_device {
 	struct device *dev;
 	struct clk *pll_ref;
 	struct clk *aclk;
-	void __iomem *logicore_reg_ba;
+	struct regmap *logicore_reg_ba;
 	void __iomem *vcu_slcr_ba;
 	struct clk_onecell_data clk_data;
 	u32 coreclk;
 	u32 mcuclk;
 };
 
+static struct regmap_config vcu_settings_regmap_config = {
+	.name = "regmap",
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = 0xfff,
+	.cache_type = REGCACHE_NONE,
+};
+
 /**
  * struct xvcu_pll_cfg - Helper data
  * @fbdiv: The integer portion of the feedback divider to the PLL
@@ -305,10 +287,12 @@ static int xvcu_set_vcu_pll_info(struct xvcu_device *xvcu)
 	int ret, i;
 	const struct xvcu_pll_cfg *found = NULL;
 
-	inte = xvcu_read(xvcu->logicore_reg_ba, VCU_PLL_CLK);
-	deci = xvcu_read(xvcu->logicore_reg_ba, VCU_PLL_CLK_DEC);
-	coreclk = xvcu_read(xvcu->logicore_reg_ba, VCU_CORE_CLK) * MHZ;
-	mcuclk = xvcu_read(xvcu->logicore_reg_ba, VCU_MCU_CLK) * MHZ;
+	regmap_read(xvcu->logicore_reg_ba, VCU_PLL_CLK, &inte);
+	regmap_read(xvcu->logicore_reg_ba, VCU_PLL_CLK_DEC, &deci);
+	regmap_read(xvcu->logicore_reg_ba, VCU_CORE_CLK, &coreclk);
+	coreclk *= MHZ;
+	regmap_read(xvcu->logicore_reg_ba, VCU_MCU_CLK, &mcuclk);
+	mcuclk *= MHZ;
 	if (!mcuclk || !coreclk) {
 		dev_err(xvcu->dev, "Invalid mcu and core clock data\n");
 		return -EINVAL;
@@ -548,6 +532,7 @@ static int xvcu_probe(struct platform_device *pdev)
 {
 	struct resource *res;
 	struct xvcu_device *xvcu;
+	void __iomem *regs;
 	int ret;
 
 	xvcu = devm_kzalloc(&pdev->dev, sizeof(*xvcu), GFP_KERNEL);
@@ -568,17 +553,32 @@ static int xvcu_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "logicore");
-	if (!res) {
-		dev_err(&pdev->dev, "get logicore memory resource failed.\n");
-		return -ENODEV;
-	}
+	xvcu->logicore_reg_ba =
+		syscon_regmap_lookup_by_compatible("xlnx,vcu-settings");
+	if (IS_ERR(xvcu->logicore_reg_ba)) {
+		dev_info(&pdev->dev,
+			 "could not find xlnx,vcu-settings: trying direct register access\n");
+
+		res = platform_get_resource_byname(pdev,
+						   IORESOURCE_MEM, "logicore");
+		if (!res) {
+			dev_err(&pdev->dev, "get logicore memory resource failed.\n");
+			return -ENODEV;
+		}
 
-	xvcu->logicore_reg_ba = devm_ioremap(&pdev->dev, res->start,
-						     resource_size(res));
-	if (!xvcu->logicore_reg_ba) {
-		dev_err(&pdev->dev, "logicore register mapping failed.\n");
-		return -ENOMEM;
+		regs = devm_ioremap(&pdev->dev, res->start, resource_size(res));
+		if (!regs) {
+			dev_err(&pdev->dev, "logicore register mapping failed.\n");
+			return -ENOMEM;
+		}
+
+		xvcu->logicore_reg_ba =
+			devm_regmap_init_mmio(&pdev->dev, regs,
+					      &vcu_settings_regmap_config);
+		if (IS_ERR(xvcu->logicore_reg_ba)) {
+			dev_err(&pdev->dev, "failed to init regmap\n");
+			return PTR_ERR(xvcu->logicore_reg_ba);
+		}
 	}
 
 	xvcu->aclk = devm_clk_get(&pdev->dev, "aclk");
@@ -610,7 +610,7 @@ static int xvcu_probe(struct platform_device *pdev)
 	 * Bit 0 : Gasket isolation
 	 * Bit 1 : put VCU out of reset
 	 */
-	xvcu_write(xvcu->logicore_reg_ba, VCU_GASKET_INIT, VCU_GASKET_VALUE);
+	regmap_write(xvcu->logicore_reg_ba, VCU_GASKET_INIT, VCU_GASKET_VALUE);
 
 	/* Do the PLL Settings based on the ref clk,core and mcu clk freq */
 	ret = xvcu_set_pll(xvcu);
@@ -657,7 +657,7 @@ static int xvcu_remove(struct platform_device *pdev)
 	xvcu_unregister_clock_provider(xvcu);
 
 	/* Add the the Gasket isolation and put the VCU in reset. */
-	xvcu_write(xvcu->logicore_reg_ba, VCU_GASKET_INIT, 0);
+	regmap_write(xvcu->logicore_reg_ba, VCU_GASKET_INIT, 0);
 
 	clk_disable_unprepare(xvcu->pll_ref);
 	clk_disable_unprepare(xvcu->aclk);
diff --git a/include/linux/mfd/syscon/xlnx-vcu.h b/include/linux/mfd/syscon/xlnx-vcu.h
new file mode 100644
index 000000000000..d3edec4b7b1d
--- /dev/null
+++ b/include/linux/mfd/syscon/xlnx-vcu.h
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2020 Pengutronix, Michael Tretter <kernel@pengutronix.de>
+ */
+
+#ifndef __XLNX_VCU_H
+#define __XLNX_VCU_H
+
+#define VCU_ECODER_ENABLE		0x00
+#define VCU_DECODER_ENABLE		0x04
+#define VCU_MEMORY_DEPTH		0x08
+#define VCU_ENC_COLOR_DEPTH		0x0c
+#define VCU_ENC_VERTICAL_RANGE		0x10
+#define VCU_ENC_FRAME_SIZE_X		0x14
+#define VCU_ENC_FRAME_SIZE_Y		0x18
+#define VCU_ENC_COLOR_FORMAT		0x1c
+#define VCU_ENC_FPS			0x20
+#define VCU_MCU_CLK			0x24
+#define VCU_CORE_CLK			0x28
+#define VCU_PLL_BYPASS			0x2c
+#define VCU_ENC_CLK			0x30
+#define VCU_PLL_CLK			0x34
+#define VCU_ENC_VIDEO_STANDARD		0x38
+#define VCU_STATUS			0x3c
+#define VCU_AXI_ENC_CLK			0x40
+#define VCU_AXI_DEC_CLK			0x44
+#define VCU_AXI_MCU_CLK			0x48
+#define VCU_DEC_VIDEO_STANDARD		0x4c
+#define VCU_DEC_FRAME_SIZE_X		0x50
+#define VCU_DEC_FRAME_SIZE_Y		0x54
+#define VCU_DEC_FPS			0x58
+#define VCU_BUFFER_B_FRAME		0x5c
+#define VCU_WPP_EN			0x60
+#define VCU_PLL_CLK_DEC			0x64
+#define VCU_GASKET_INIT			0x74
+#define VCU_GASKET_VALUE		0x03
+
+#endif /* __XLNX_VCU_H */
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 6/6] soc: xilinx: vcu: add missing register NUM_CORE

[Michael Tretter]

The H.264/H.265 Video Codec Unit v1.2 documentation describes this
register as follows:

	Number of encoders core used for the provided configuration

This is required for configuring the VCU encoder buffer.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
---
Changelog:

v2 -> v3:
- none

v1 -> v2:
- none
---
 include/linux/mfd/syscon/xlnx-vcu.h | 1 +
 1 file changed, 1 insertion(+)

diff --git a/include/linux/mfd/syscon/xlnx-vcu.h b/include/linux/mfd/syscon/xlnx-vcu.h
index d3edec4b7b1d..ff7bc3656f6e 100644
--- a/include/linux/mfd/syscon/xlnx-vcu.h
+++ b/include/linux/mfd/syscon/xlnx-vcu.h
@@ -32,6 +32,7 @@
 #define VCU_BUFFER_B_FRAME		0x5c
 #define VCU_WPP_EN			0x60
 #define VCU_PLL_CLK_DEC			0x64
+#define VCU_NUM_CORE			0x6c
 #define VCU_GASKET_INIT			0x74
 #define VCU_GASKET_VALUE		0x03
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 2/6] ARM: dts: define indexes for output clocks

[Rob Herring]

On Fri, 17 Apr 2020 09:05:22 +0200, Michael Tretter wrote:
> The VCU System-Level Control provides 4 clocks. Defined indexes for
> these clocks.
> 
> Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
> ---
> Changelog:
> 
> v2 -> v3:
> - none
> 
> v1 -> v2:
> - none
> ---
>  include/dt-bindings/clock/xlnx-vcu.h | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
>  create mode 100644 include/dt-bindings/clock/xlnx-vcu.h
> 

Acked-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 4/6] dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding

[Rob Herring]

On Fri, 17 Apr 2020 09:05:24 +0200, Michael Tretter wrote:
> The xlnx,vcu binding comprises two adjacent register banks:
> 
> The first register bank ("vcu_slcr") contains registers for setting the
> clocks of the vcu and controlling the performance monitors. The second
> bank ("logicoreip") contains the configuration settings of the video codec
> unit, which are set before synthesizing the bitstream.
> 
> Drivers that drive the actual video codec unit need to to read the
> registers from the logicoreip register bank for configuring the vcu
> firmware.
> 
> As logicoreip is a too generic name for this register bank, use
> "vcu-settings" as a binding name, because the register bank basically
> provides the configuration settings of the VCU.
> 
> Therefore, add the vcu-settings binding to provide a syscon interface
> for other drivers to read these registers.
> 
> The alternative would have been to merge the two register banks of the
> xlnx,vcu binding into one register bank and make xlnx,vcu provide a
> syscon interface, but that would lead to more incompatibility than
> making second register bank of xlnx,vcu optional.
> 
> Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
> ---
> Changelog:
> 
> v2 -> v3:
> - none
> 
> v1 -> v2:
> - drop custom select for syscon
> ---
>  .../soc/xilinx/xlnx,vcu-settings.yaml         | 34 +++++++++++++++++++
>  .../bindings/soc/xilinx/xlnx,vcu.txt          |  9 ++---
>  2 files changed, 36 insertions(+), 7 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/soc/xilinx/xlnx,vcu-settings.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel