From: peter@hurleysoftware.com (Peter Hurley)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 09/16] tty: serial: 8250_dma: Add a TX trigger workaround for AM33xx
Date: Thu, 11 Sep 2014 10:35:43 -0400 [thread overview]
Message-ID: <5411B33F.10405@hurleysoftware.com> (raw)
In-Reply-To: <54119AAA.9080907@linutronix.de>
On 09/11/2014 08:50 AM, Sebastian Andrzej Siewior wrote:
> On 09/11/2014 02:32 PM, Peter Hurley wrote:
>> On 09/11/2014 07:42 AM, Sebastian Andrzej Siewior wrote:
>>> I also need a watchdog timer for TX since it seems that on omap3 the
>>> DMA engine suddenly forgets to continue with DMA?
>>
>> One difference I noticed between the omap driver and the 8250 driver is
>> the way modem status interrupts are handled.
>>
>> The omap driver only checks modem status for the UART_IIR_MSI interrupt type.
>> The 8250 driver checks modem status at every interrupt (other than NO_INT).
>>
>> I think the UART_MSR_DCTS bit always reflects that the CTS input has changed
>> between reads of the MSR _even if auto CTS is on_. So perhaps the hardware
>> is being stopped by uart_handle_cts_change() when auto CTS is on?
>
> I doubt that. What I see from a timer debug is that the TX-FIFO level
> is at 0, the DMA transfer for say 1024 bytes start.
> The FIFO is filled to 64bytes and refilled so it doesn't drop below 50.
> At the time of the stall I see that the DMA engine has outstanding
> bytes which it should transfer and the TX FIFO is empty. If hardware
> flow control stops the transfer, I would expect that the DMA engine
> still fills the TX-FIFO until 64 and then waits. But it doesn't.
> Writing bytes into the FIFO leads to bytes beeing sent (and I see them
> on the other side) but the DMA transfer is still on hold. Canceling the
> DMA transfer and re-programming the remaining bytes transfers the
> remaining bytes.
>
> The odd thing is that I only triggered it with "less file". It doesn't
> happen on regular console interaction or "cat large-file". And it only
> triggers on beagle board xm (omap34xx) and I wasn't able to reproduce
> it on am335x or dra7. The latter shares the same DMA engine as beagle
> board xm.
>
> I remember also that I disabled the HW/SW float control just to make
> sure it is not it.
Ok.
I do need to find out if omap hardware sets UART_MSR_DCTS when auto CTS
is on. Would you mind running the debug patch below with HW flow control on?
Regards,
Peter Hurley
--- >% ---
Subject: [DEBUG] serial: does OMAP set UART_LSR_DCTS while autoCTS is on?
** debug patch only **
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
---
drivers/tty/serial/serial_core.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 5a78f69..1579a20 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -2783,6 +2783,9 @@ void uart_handle_cts_change(struct uart_port *uport, unsigned int status)
uport->icount.cts++;
if (tty_port_cts_enabled(port)) {
+
+ WARN_ON_ONCE(uport->flags & UPF_HARD_FLOW);
+
if (tty->hw_stopped) {
if (status) {
tty->hw_stopped = 0;
--
2.1.0
next prev parent reply other threads:[~2014-09-11 14:35 UTC|newest]
Thread overview: 97+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-10 19:29 [PATCH 00/16 v9] omap 8250 based uart + DMA Sebastian Andrzej Siewior
2014-09-10 19:29 ` [PATCH 01/16] tty: serial: 8250_core: allow to set ->throttle / ->unthrottle callbacks Sebastian Andrzej Siewior
2014-09-10 19:29 ` [PATCH 02/16] tty: serial: 8250_core: add run time pm Sebastian Andrzej Siewior
2014-09-29 9:46 ` Frans Klaver
2014-09-29 13:39 ` Sebastian Andrzej Siewior
2014-09-10 19:29 ` [PATCH 03/16] tty: serial: 8250_core: read only RX if there is something in the FIFO Sebastian Andrzej Siewior
2015-02-09 13:34 ` Nicolas Schichan
2015-02-09 23:34 ` Peter Hurley
2015-02-10 9:32 ` Sebastian Andrzej Siewior
2015-02-10 12:04 ` Nicolas Schichan
2015-02-10 17:46 ` Peter Hurley
2015-02-11 20:01 ` Peter Hurley
2015-02-11 20:03 ` Tony Lindgren
2015-02-11 20:42 ` Peter Hurley
2015-02-12 8:45 ` Sebastian Andrzej Siewior
2015-02-12 9:40 ` Russell King - ARM Linux
2015-02-12 16:32 ` Peter Hurley
2015-02-12 19:23 ` Sebastian Andrzej Siewior
2015-02-12 19:55 ` Peter Hurley
2015-02-12 20:34 ` Sebastian Andrzej Siewior
2015-02-13 18:51 ` Sebastian Andrzej Siewior
2015-02-13 23:15 ` Russell King - ARM Linux
2015-02-15 17:32 ` [PATCH] serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO" Sebastian Andrzej Siewior
2015-05-12 20:25 ` Tony Lindgren
2014-09-10 19:29 ` [PATCH 04/16] tty: serial: 8250_core: use the ->line argument as a hint in serial8250_find_match_or_unused() Sebastian Andrzej Siewior
2014-09-10 19:30 ` [PATCH 05/16] tty: serial: 8250_core: remove UART_IER_RDI in serial8250_stop_rx() Sebastian Andrzej Siewior
2014-09-11 11:19 ` Heikki Krogerus
2014-09-10 19:30 ` [PATCH 06/16] tty: serial: Add 8250-core based omap driver Sebastian Andrzej Siewior
2014-09-11 11:57 ` Peter Hurley
2014-09-16 17:01 ` Sebastian Andrzej Siewior
2014-09-29 9:38 ` Frans Klaver
2014-09-29 13:27 ` Sebastian Andrzej Siewior
2014-09-29 13:34 ` Frans Klaver
2014-09-10 19:30 ` [PATCH 07/16] tty: serial: 8250_dma: handle error on TX submit Sebastian Andrzej Siewior
2014-09-10 19:30 ` [PATCH 08/16] tty: serial: 8250_dma: enqueue RX dma again on completion Sebastian Andrzej Siewior
2014-09-10 19:30 ` [PATCH 09/16] tty: serial: 8250_dma: Add a TX trigger workaround for AM33xx Sebastian Andrzej Siewior
2014-09-11 11:17 ` Heikki Krogerus
2014-09-11 11:42 ` Sebastian Andrzej Siewior
2014-09-11 12:32 ` Peter Hurley
2014-09-11 12:50 ` Sebastian Andrzej Siewior
2014-09-11 14:35 ` Peter Hurley [this message]
2014-09-15 17:01 ` Sebastian Andrzej Siewior
2014-09-16 16:55 ` Sebastian Andrzej Siewior
2014-09-17 12:20 ` Peter Hurley
2014-09-17 16:25 ` Sebastian Andrzej Siewior
2014-09-29 16:15 ` Sebastian Andrzej Siewior
2014-09-11 15:11 ` Frans Klaver
2014-09-11 16:04 ` Sebastian Andrzej Siewior
2014-09-11 17:04 ` Frans Klaver
2014-09-12 7:23 ` Sebastian Andrzej Siewior
[not found] ` <20140912094010.GE28458@ci00147.xsens-tech.local>
2014-09-12 9:51 ` Sebastian Andrzej Siewior
2014-09-12 10:28 ` Frans Klaver
2014-09-15 16:42 ` Sebastian Andrzej Siewior
2014-09-16 9:05 ` Frans Klaver
2014-09-16 12:42 ` Frans Klaver
2014-09-16 14:23 ` Frans Klaver
2014-09-17 10:28 ` Frans Klaver
2014-09-21 20:41 ` Sebastian Andrzej Siewior
2014-09-22 9:28 ` Frans Klaver
2014-09-24 7:56 ` Sebastian Andrzej Siewior
2014-09-25 15:14 ` Sebastian Andrzej Siewior
2014-09-25 15:18 ` Frans Klaver
2014-09-29 8:50 ` Frans Klaver
2014-09-29 9:54 ` Sebastian Andrzej Siewior
2014-09-29 10:30 ` Frans Klaver
2014-09-30 8:44 ` Frans Klaver
2014-10-02 10:27 ` Sebastian Andrzej Siewior
2014-10-13 14:55 ` Frans Klaver
2014-09-23 17:03 ` Peter Hurley
2014-09-24 7:53 ` Sebastian Andrzej Siewior
2014-09-25 10:42 ` Sebastian Andrzej Siewior
2014-09-25 11:31 ` Peter Hurley
2014-09-25 13:11 ` Sebastian Andrzej Siewior
2014-09-17 16:34 ` Sebastian Andrzej Siewior
2014-09-19 10:22 ` Heikki Krogerus
2014-09-19 10:58 ` Sebastian Andrzej Siewior
2014-09-19 11:25 ` Peter Hurley
2014-09-22 7:46 ` Heikki Krogerus
2014-09-25 9:24 ` Sebastian Andrzej Siewior
2014-09-10 19:30 ` [PATCH 10/16] tty: serial: 8250_dma: optimize the xmit path due to UART_BUG_DMA_TX Sebastian Andrzej Siewior
2014-09-10 19:30 ` [PATCH 11/16] tty: serial: 8250_dma: keep own book keeping about RX transfers Sebastian Andrzej Siewior
2014-09-10 19:30 ` [PATCH 12/16] tty: serial: 8250_dma: handle the UART RDI event while DMA remains idle Sebastian Andrzej Siewior
2014-09-29 9:23 ` Frans Klaver
2014-09-10 19:30 ` [PATCH 13/16] tty: serial: 8250_dma: add pm runtime Sebastian Andrzej Siewior
2014-09-29 9:26 ` Frans Klaver
2014-09-29 9:56 ` Sebastian Andrzej Siewior
2014-09-10 19:30 ` [PATCH 14/16] arm: dts: am33xx: add DMA properties for UART Sebastian Andrzej Siewior
2014-09-10 19:30 ` [PATCH 15/16] arm: dts: dra7: " Sebastian Andrzej Siewior
2014-09-10 19:30 ` [PATCH 16/16] tty: serial: 8250: omap: add dma support Sebastian Andrzej Siewior
2014-09-12 22:43 ` [PATCH 00/16 v9] omap 8250 based uart + DMA Tony Lindgren
2014-09-15 11:50 ` Sebastian Andrzej Siewior
2014-09-16 12:57 ` Sebastian Andrzej Siewior
2014-09-16 16:48 ` Tony Lindgren
2014-09-16 21:30 ` Tony Lindgren
2014-09-17 8:38 ` Sebastian Andrzej Siewior
2014-09-17 9:05 ` Sebastian Andrzej Siewior
2014-09-26 16:02 ` Greg KH
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5411B33F.10405@hurleysoftware.com \
--to=peter@hurleysoftware.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).