Re: [PATCH 07/15] dt: thermal: tsens: Document interrupt support in tsens driver

[Amit Kucheria <amit.kucheria@linaro.org>]

On Sat, Aug 17, 2019 at 3:06 AM Rob Herring <robh@kernel.org> wrote:
>
> On Fri, Jul 26, 2019 at 03:48:42AM +0530, Amit Kucheria wrote:
> > Define two new required properties to define interrupts and
> > interrupt-names for tsens.
> >
> > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> > ---
> >  Documentation/devicetree/bindings/thermal/qcom-tsens.txt | 5 +++++
> >  1 file changed, 5 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
> > index 673cc1831ee9..3d3dd5dc6d36 100644
> > --- a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
> > +++ b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
> > @@ -22,6 +22,8 @@ Required properties:
> >
> >  - #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
> >  - #qcom,sensors: Number of sensors in tsens block
> > +- interrupts: Interrupts generated from Always-On subsystem (AOSS)
> > +- interrupt-names: The name of the interrupt e.g. "tsens0", "tsens1"
>
> How many interrupts? A name with just indices isn't too useful.

Depending on the version of the tsens IP, there can be 1 (upper/lower
threshold), 2 (upper/lower + critical threshold) or 3 (upper/lower +
critical + zero degree) interrupts. This patch series only introduces
support for a single interrupt (upper/lower).

I used the names tsens0, tsens1 to encapsulate the controller instance
since some SoCs have 1 controller, others have two. So we'll end up
with something like the following in DT:

tsens0: thermal-sensor@c263000 {
                        compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
                        reg = <0 0x0c263000 0 0x1ff>, /* TM */
                              <0 0x0c222000 0 0x1ff>; /* SROT */
                        #qcom,sensors = <13>;
                        interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
                                     <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
                        interrupt-names = "tsens0", "tsens0-critical";
                        #thermal-sensor-cells = <1>;
};

tsens1: thermal-sensor@c265000 {
                        compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
                        reg = <0 0x0c265000 0 0x1ff>, /* TM */
                              <0 0x0c223000 0 0x1ff>; /* SROT */
                        #qcom,sensors = <8>;
                        interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
                                     <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
                        interrupt-names = "tsens1", "tsens1-critical";
                        #thermal-sensor-cells = <1>;
}

Does that work?

Regards,
Amit

> >  - Refer to Documentation/devicetree/bindings/nvmem/nvmem.txt to know how to specify
> >  nvmem cells
> >
> > @@ -40,6 +42,9 @@ tsens0: thermal-sensor@c263000 {
> >               reg = <0xc263000 0x1ff>, /* TM */
> >                       <0xc222000 0x1ff>; /* SROT */
> >               #qcom,sensors = <13>;
> > +             interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>;
> > +             interrupt-names = "tsens0";
> > +
> >               #thermal-sensor-cells = <1>;
> >       };
> >
> > --
> > 2.17.1
> >