linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Cc: linux-arm-msm@vger.kernel.org,
	Linus Walleij <linus.walleij@linaro.org>,
	Liam Girdwood <lgirdwood@gmail.com>,
	Mark Brown <broonie@kernel.org>, Vinod Koul <vkoul@kernel.org>,
	Rob Herring <robh+dt@kernel.org>, Andy Gross <agross@kernel.org>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-gpio@vger.kernel.org, bhupesh.linux@gmail.com
Subject: Re: [PATCH 7/8] arm64: dts: qcom: pmm8155au_2: Add base dts file
Date: Thu, 10 Jun 2021 22:13:28 -0500	[thread overview]
Message-ID: <YMLU2D+Jkfs6dmM9@builder.lan> (raw)
In-Reply-To: <20210607113840.15435-8-bhupesh.sharma@linaro.org>

On Mon 07 Jun 06:38 CDT 2021, Bhupesh Sharma wrote:

> Add base DTS file for pmm8155au_2 along with GPIOs, power-on, rtc and vadc
> nodes.
> 
> Cc: Linus Walleij <linus.walleij@linaro.org>
> Cc: Liam Girdwood <lgirdwood@gmail.com>
> Cc: Mark Brown <broonie@kernel.org>
> Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
> Cc: Vinod Koul <vkoul@kernel.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Andy Gross <agross@kernel.org>
> Cc: devicetree@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-gpio@vger.kernel.org
> Cc: bhupesh.linux@gmail.com
> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi | 107 ++++++++++++++++++++++
>  1 file changed, 107 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi

As with _1, I approve of this design.

> new file mode 100644
> index 000000000000..11c0c203a4e2
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
> @@ -0,0 +1,107 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, Linaro Limited
> + */
> +
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +/ {
> +	thermal-zones {
> +		pmm8155au-2-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +
> +			thermal-sensors = <&pmm8155au_2_temp>;
> +
> +			trips {
> +				trip0 {
> +					temperature = <95000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				trip1 {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "hot";
> +				};
> +
> +				trip2 {
> +					temperature = <145000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&spmi_bus {
> +	pmic@4 {
> +		compatible = "qcom,pmm8155au-2", "qcom,spmi-pmic";

"qcom,pmm8155au", "qcom,spmi-pmic"

> +		reg = <0x4 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		power-on@800 {
> +			compatible = "qcom,pm8916-pon";
> +			reg = <0x0800>;
> +
> +			status = "disabled";
> +		};
> +
> +		pmm8155au_2_temp: temp-alarm@2400 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0x2400>;
> +			interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			io-channels = <&pmm8155au_2_adc ADC5_DIE_TEMP>;
> +			io-channel-names = "thermal";
> +			#thermal-sensor-cells = <0>;
> +		};
> +
> +		pmm8155au_2_adc: adc@3100 {
> +			compatible = "qcom,spmi-adc5";
> +			reg = <0x3100>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			#io-channel-cells = <1>;
> +			interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
> +
> +			ref-gnd@0 {
> +				reg = <ADC5_REF_GND>;
> +				qcom,pre-scaling = <1 1>;
> +				label = "ref_gnd";
> +			};
> +
> +			vref-1p25@1 {
> +				reg = <ADC5_1P25VREF>;
> +				qcom,pre-scaling = <1 1>;
> +				label = "vref_1p25";
> +			};
> +
> +			die-temp@6 {
> +				reg = <ADC5_DIE_TEMP>;
> +				qcom,pre-scaling = <1 1>;
> +				label = "die_temp";
> +			};
> +		};
> +
> +		pmm8155au_2_gpios: gpio@c000 {
> +			compatible = "qcom,pmm8155au-2-gpio";

"qcom,pmm8155-gpio"

> +			reg = <0xc000>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	pmic@5 {
> +		compatible = "qcom,pmm8155au-2", "qcom,spmi-pmic";

"qcom,pmm8155au", "qcom,spmi-pmic"

Regards,
Bjorn

> +		reg = <0x5 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +};
> -- 
> 2.31.1
> 

  reply	other threads:[~2021-06-11  3:14 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-06-07 11:38 [PATCH 0/8] arm64: dts: qcom: Add SA8155p-adp board DTS Bhupesh Sharma
2021-06-07 11:38 ` [PATCH 1/8] dt-bindings: qcom: rpmh-regulator: Add compatible for SA8155p-adp board pmics Bhupesh Sharma
2021-06-11  2:48   ` Bjorn Andersson
2021-06-14  8:05     ` Bhupesh Sharma
2021-06-14 16:28       ` Bjorn Andersson
2021-06-15  4:43         ` Bhupesh Sharma
2021-06-07 11:38 ` [PATCH 2/8] dt-bindings: pinctrl: qcom,pmic-gpio: Add compatible for SA8155p-adp Bhupesh Sharma
2021-06-11  2:51   ` Bjorn Andersson
2021-06-14  8:13     ` Bhupesh Sharma
2021-06-14 16:09       ` Bjorn Andersson
2021-06-07 11:38 ` [PATCH 3/8] dt-bindings: arm: qcom: Add compatible for SA8155p-adp board Bhupesh Sharma
2021-06-11  2:59   ` Bjorn Andersson
2021-06-14  8:14     ` Bhupesh Sharma
2021-06-07 11:38 ` [PATCH 4/8] regulator: qcom-rpmh: Add new regulator types found on SA8155p adp board Bhupesh Sharma
2021-06-07 12:09   ` Andy Shevchenko
2021-06-07 12:30     ` Bhupesh Sharma
2021-06-14 16:17       ` Bjorn Andersson
2021-06-15  4:47         ` Bhupesh Sharma
2021-06-07 11:38 ` [PATCH 5/8] pinctrl: qcom/pinctrl-spmi-gpio: Add compatibles for pmic-gpios on SA8155p-adp Bhupesh Sharma
2021-06-11  3:00   ` Bjorn Andersson
2021-06-14  8:30     ` Bhupesh Sharma
2021-06-14 16:12       ` Bjorn Andersson
2021-06-07 11:38 ` [PATCH 6/8] arm64: dts: qcom: pmm8155au_1: Add base dts file Bhupesh Sharma
2021-06-11  3:12   ` Bjorn Andersson
2021-06-07 11:38 ` [PATCH 7/8] arm64: dts: qcom: pmm8155au_2: " Bhupesh Sharma
2021-06-11  3:13   ` Bjorn Andersson [this message]
2021-06-07 11:38 ` [PATCH 8/8] arm64: dts: qcom: sa8155p-adp: " Bhupesh Sharma
2021-06-07 15:22   ` Vinod Koul
2021-06-07 21:22     ` Bhupesh Sharma
2021-06-11  2:25   ` Bjorn Andersson
2021-06-14  8:19     ` Bhupesh Sharma
2021-06-15  4:41     ` Bhupesh Sharma

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=YMLU2D+Jkfs6dmM9@builder.lan \
    --to=bjorn.andersson@linaro.org \
    --cc=agross@kernel.org \
    --cc=bhupesh.linux@gmail.com \
    --cc=bhupesh.sharma@linaro.org \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=lgirdwood@gmail.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).