[PATCH AUTOSEL 5.10 29/45] dts: phy: fix missing mdio device and probe failure of vsc8541-01 device

[PATCH AUTOSEL 5.10 29/45] dts: phy: fix missing mdio device and probe failure of vsc8541-01 device

[Sasha Levin]

From: Sagar Shrikant Kadam <sagar.kadam@sifive.com>

[ Upstream commit be969b7cfbcfa8a835a528f1dc467f0975c6d883 ]

HiFive unleashed A00 board has VSC8541-01 ethernet phy, this device is
identified as a Revision B device as described in device identification
registers. In order to use this phy in the unmanaged mode, it requires
a specific reset sequence of logical 0-1-0-1 transition on the NRESET pin
as documented here [1].

Currently, the bootloader (fsbl or u-boot-spl) takes care of the phy reset.
If due to some reason the phy device hasn't received the reset by the prior
stages before the linux macb driver comes into the picture, the MACB mii
bus gets probed but the mdio scan fails and is not even able to read the
phy ID registers. It gives an error message:

"libphy: MACB_mii_bus: probed
mdio_bus 10090000.ethernet-ffffffff: MDIO device at address 0 is missing."

Thus adding the device OUI (Organizationally Unique Identifier) to the phy
device node helps to probe the phy device.

[1]: VSC8541-01 datasheet:
https://www.mouser.com/ds/2/523/Microsemi_VSC8541-01_Datasheet_10496_V40-1148034.pdf

Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
index 4a2729f5ca3f0..60846e88ae4b1 100644
--- a/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
+++ b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
@@ -88,6 +88,7 @@ &eth0 {
 	phy-mode = "gmii";
 	phy-handle = <&phy0>;
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0007.0771";
 		reg = <0>;
 	};
 };
-- 
2.27.0

[PATCH AUTOSEL 5.10 30/45] dts: phy: add GPIO number and active state used for phy reset

[Sasha Levin]

From: Sagar Shrikant Kadam <sagar.kadam@sifive.com>

[ Upstream commit a0fa9d727043da2238432471e85de0bdb8a8df65 ]

The GEMGXL_RST line on HiFive Unleashed is pulled low and is
using GPIO number 12. Add these reset-gpio details to dt-node
using which the linux phylib can reset the phy.

Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
index 60846e88ae4b1..24d75a146e02d 100644
--- a/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
+++ b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
@@ -90,6 +90,7 @@ &eth0 {
 	phy0: ethernet-phy@0 {
 		compatible = "ethernet-phy-id0007.0771";
 		reg = <0>;
+		reset-gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
 	};
 };
 
-- 
2.27.0