From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: Benoit Parrot <bparrot@ti.com>, Pratyush Yadav <p.yadav@ti.com>,
Lokesh Vutla <lokeshvutla@ti.com>,
linux-media@vger.kernel.org
Subject: Re: [PATCH 22/28] media: ti-vpe: cal: set field always to V4L2_FIELD_NONE
Date: Sun, 18 Apr 2021 16:14:26 +0300 [thread overview]
Message-ID: <YHwwsknGY0aC6iet@pendragon.ideasonboard.com> (raw)
In-Reply-To: <20210412113457.328012-23-tomi.valkeinen@ideasonboard.com>
Hi Tomi,
Thank you for the patch.
On Mon, Apr 12, 2021 at 02:34:51PM +0300, Tomi Valkeinen wrote:
> cal_camerarx_sd_set_fmt() accepts any value for the format field, but
> there should be no reason to have any other value accepted than
> V4L2_FIELD_NONE. So set the field always to V4L2_FIELD_NONE.
What if the source produces V4L2_FIELD_INTERLACED_(TB|BT) ? Shouldn't we
accept that and propagate it ? Same for V4L2_FIELD_TOP and
V4L2_FIELD_BOTTOM I suppose. V4L2_FIELD_SEQ_(TB|BT) is likely not needed
as I doubt sources will send that. V4L2_FIELD_ALTERNATE is a bit more
tricky, as the driver has to report which field a particular buffer
contains, and I'm not sure we could do so (maybe based on the CSI-2
frame number ?).
I'm fine dropping support for interlaced formats until someone wants to
support them though, it's up to you.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
> ---
> drivers/media/platform/ti-vpe/cal-camerarx.c | 6 ++----
> 1 file changed, 2 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/media/platform/ti-vpe/cal-camerarx.c b/drivers/media/platform/ti-vpe/cal-camerarx.c
> index 245c601b992c..880261d53a1d 100644
> --- a/drivers/media/platform/ti-vpe/cal-camerarx.c
> +++ b/drivers/media/platform/ti-vpe/cal-camerarx.c
> @@ -702,10 +702,7 @@ static int cal_camerarx_sd_set_fmt(struct v4l2_subdev *sd,
> if (!fmtinfo)
> fmtinfo = &cal_formats[0];
>
> - /*
> - * Clamp the size, update the code. The field and colorspace are
> - * accepted as-is.
> - */
> + /* Clamp the size, update the code. The colorspace is accepted as-is. */
> bpp = ALIGN(fmtinfo->bpp, 8);
>
> format->format.width = clamp_t(unsigned int, format->format.width,
> @@ -715,6 +712,7 @@ static int cal_camerarx_sd_set_fmt(struct v4l2_subdev *sd,
> CAL_MIN_HEIGHT_LINES,
> CAL_MAX_HEIGHT_LINES);
> format->format.code = fmtinfo->code;
> + format->format.field = V4L2_FIELD_NONE;
>
> /* Store the format and propagate it to the source pad. */
> fmt = cal_camerarx_get_pad_format(phy, cfg, CAL_CAMERARX_PAD_SINK,
--
Regards,
Laurent Pinchart
next prev parent reply other threads:[~2021-04-18 13:14 UTC|newest]
Thread overview: 84+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-04-12 11:34 [PATCH 00/28] media: ti-vpe: cal: prepare for multistream support Tomi Valkeinen
2021-04-12 11:34 ` [PATCH 01/28] media: ti-vpe: cal: add g/s_parm for legacy API Tomi Valkeinen
2021-04-17 23:01 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 02/28] media: ti-vpe: cal: fix error handling in cal_camerarx_create Tomi Valkeinen
2021-04-17 23:05 ` Laurent Pinchart
2021-04-19 8:24 ` Tomi Valkeinen
2021-04-19 8:31 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 03/28] media: ti-vpe: cal: remove unused cal_camerarx->dev field Tomi Valkeinen
2021-04-18 0:43 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 04/28] media: ti-vpe: cal: rename "sensor" to "source" Tomi Valkeinen
2021-04-17 23:18 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 05/28] media: ti-vpe: cal: move global config from cal_ctx_wr_dma_config to runtime resume Tomi Valkeinen
2021-04-17 23:27 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 06/28] media: ti-vpe: cal: use v4l2_get_link_freq Tomi Valkeinen
2021-04-18 11:48 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 07/28] media: ti-vpe: cal: add cal_ctx_prepare/unprepare Tomi Valkeinen
2021-04-18 13:30 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 08/28] media: ti-vpe: cal: change index and cport to u8 Tomi Valkeinen
2021-04-18 11:55 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 09/28] media: ti-vpe: cal: Add PPI context Tomi Valkeinen
2021-04-18 12:17 ` Laurent Pinchart
2021-04-19 9:01 ` Tomi Valkeinen
2021-04-12 11:34 ` [PATCH 10/28] media: ti-vpe: cal: Add pixel processing context Tomi Valkeinen
2021-04-18 12:20 ` Laurent Pinchart
2021-04-18 12:23 ` Laurent Pinchart
2021-04-19 9:17 ` Tomi Valkeinen
2021-04-12 11:34 ` [PATCH 11/28] media: ti-vpe: cal: rename cal_ctx->index to dma_ctx Tomi Valkeinen
2021-04-18 12:22 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 12/28] media: ti-vpe: cal: rename CAL_HL_IRQ_MASK Tomi Valkeinen
2021-04-18 12:29 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 13/28] media: ti-vpe: cal: clean up CAL_CSI2_VC_IRQ_* macros Tomi Valkeinen
2021-04-18 12:32 ` Laurent Pinchart
2021-04-19 10:29 ` Tomi Valkeinen
2021-04-12 11:34 ` [PATCH 14/28] media: ti-vpe: cal: catch VC errors Tomi Valkeinen
2021-04-18 12:38 ` Laurent Pinchart
2021-04-19 11:19 ` Tomi Valkeinen
2021-04-28 23:44 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 15/28] media: ti-vpe: cal: remove wait when stopping camerarx Tomi Valkeinen
2021-04-18 12:46 ` Laurent Pinchart
2021-04-19 11:29 ` Tomi Valkeinen
2021-04-28 23:57 ` Laurent Pinchart
2021-05-04 7:56 ` Tomi Valkeinen
2021-06-04 13:44 ` Laurent Pinchart
2021-06-07 10:41 ` Tomi Valkeinen
2021-06-09 12:31 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 16/28] media: ti-vpe: cal: disable ppi and pix proc at ctx_stop Tomi Valkeinen
2021-04-18 12:49 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 17/28] media: ti-vpe: cal: allocate pix proc dynamically Tomi Valkeinen
2021-04-18 12:59 ` Laurent Pinchart
2021-04-19 11:45 ` Tomi Valkeinen
2021-04-29 0:04 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 18/28] media: ti-vpe: cal: add 'use_pix_proc' field Tomi Valkeinen
2021-04-18 13:00 ` Laurent Pinchart
2021-04-19 11:53 ` Tomi Valkeinen
2021-04-29 0:07 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 19/28] media: ti-vpe: cal: add cal_ctx_wr_dma_enable and fix a race Tomi Valkeinen
2021-04-18 13:04 ` Laurent Pinchart
2021-04-19 12:02 ` Tomi Valkeinen
2021-04-12 11:34 ` [PATCH 20/28] media: ti-vpe: cal: add vc and datatype fields to cal_ctx Tomi Valkeinen
2021-04-18 13:06 ` Laurent Pinchart
2021-04-19 12:07 ` Tomi Valkeinen
2021-04-12 11:34 ` [PATCH 21/28] media: ti-vpe: cal: fix cal_ctx_v4l2_register error handling Tomi Valkeinen
2021-04-18 13:09 ` Laurent Pinchart
2021-04-20 10:50 ` Tomi Valkeinen
2021-04-20 11:17 ` Tomi Valkeinen
2021-04-29 0:10 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 22/28] media: ti-vpe: cal: set field always to V4L2_FIELD_NONE Tomi Valkeinen
2021-04-18 13:14 ` Laurent Pinchart [this message]
2021-04-19 12:34 ` Tomi Valkeinen
2021-04-12 11:34 ` [PATCH 23/28] media: ti-vpe: cal: fix typo in a comment Tomi Valkeinen
2021-04-18 13:14 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 24/28] media: ti-vpe: cal: add mbus_code support to cal_mc_enum_fmt_vid_cap Tomi Valkeinen
2021-04-18 13:17 ` Laurent Pinchart
2021-04-19 12:50 ` Tomi Valkeinen
2021-04-12 11:34 ` [PATCH 25/28] media: ti-vpe: cal: rename non-MC funcs to cal_legacy_* Tomi Valkeinen
2021-04-18 13:18 ` Laurent Pinchart
2021-04-12 11:34 ` [PATCH 26/28] media: ti-vpe: cal: init ctx->v_fmt correctly in MC mode Tomi Valkeinen
2021-04-18 13:21 ` Laurent Pinchart
2021-04-19 13:01 ` Tomi Valkeinen
2021-04-12 11:34 ` [PATCH 27/28] media: ti-vpe: cal: remove cal_camerarx->fmtinfo Tomi Valkeinen
2021-04-18 13:24 ` Laurent Pinchart
2021-04-19 13:08 ` Tomi Valkeinen
2021-04-12 11:34 ` [PATCH 28/28] media: ti-vpe: cal: support 8 DMA contexts Tomi Valkeinen
2021-04-18 13:29 ` Laurent Pinchart
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YHwwsknGY0aC6iet@pendragon.ideasonboard.com \
--to=laurent.pinchart@ideasonboard.com \
--cc=bparrot@ti.com \
--cc=linux-media@vger.kernel.org \
--cc=lokeshvutla@ti.com \
--cc=p.yadav@ti.com \
--cc=tomi.valkeinen@ideasonboard.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).