[PATCH v4 RESEND 0/8] ipq9574: Enable PCI-Express support

[PATCH v4 RESEND 0/8] ipq9574: Enable PCI-Express support

[Alexandru Gagniuc]

There are four PCIe ports on IPQ9574, pcie0 thru pcie3. This series
addresses pcie2, which is a gen3x2 port. The board I have only uses
pcie2, and that's the only one enabled in this series. pcie3 is added
as a special request, but is untested.

I believe this makes sense as a monolithic series, as the individual
pieces are not that useful by themselves.

In v2, I've had some issues regarding the dt schema checks. For
transparency, I used the following test invocations to test:

      make dt_binding_check     DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml
      make dtbs_check           DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml

Changes since v3:
 - "const"ify .hw.init fields for the PCIE pipe clocks
 - Used pciephy_v5_regs_layout instead of v4 in phy-qcom-qmp-pcie.c
 - Included Manivannan's patch for qcom-pcie.c clocks
 - Dropped redundant comments in "ranges" and "interrupt-map" of pcie2.
 - Added pcie3 and pcie3_phy dts nodes
 - Moved snoc and anoc clocks to PCIe controller from PHY

Changes since v2:
 - reworked resets in qcom,pcie.yaml to resolve dt schema errors
 - constrained "reg" in qcom,pcie.yaml
 - reworked min/max intems in qcom,ipq8074-qmp-pcie-phy.yaml
 - dropped msi-parent for pcie node, as it is handled by "msi" IRQ

Changes since v1:
 - updated new tables in phy-qcom-qmp-pcie.c to use lowercase hex numbers
 - reorganized qcom,ipq8074-qmp-pcie-phy.yaml to use a single list of clocks
 - reorganized qcom,pcie.yaml to include clocks+resets per compatible
 - Renamed "pcie2_qmp_phy" label to "pcie2_phy"
 - moved "ranges" property of pcie@20000000 higher up

Alexandru Gagniuc (7):
  dt-bindings: clock: Add PCIe pipe related clocks for IPQ9574
  clk: qcom: gcc-ipq9574: Add PCIe pipe clocks
  dt-bindings: PCI: qcom: Add IPQ9574 PCIe controller
  PCI: qcom: Add support for IPQ9574
  dt-bindings: phy: qcom,ipq8074-qmp-pcie: add ipq9574 gen3x2 PHY
  phy: qcom-qmp-pcie: add support for ipq9574 gen3x2 PHY
  arm64: dts: qcom: ipq9574: add PCIe2 and PCIe3 nodes

Manivannan Sadhasivam (1):
  PCI: qcom: Switch to devm_clk_bulk_get_all() API to get the clocks
    from Devicetree

 .../devicetree/bindings/pci/qcom,pcie.yaml    |  37 ++++
 .../phy/qcom,ipq8074-qmp-pcie-phy.yaml        |   1 +
 arch/arm64/boot/dts/qcom/ipq9574.dtsi         | 178 +++++++++++++++++-
 drivers/clk/qcom/gcc-ipq9574.c                |  76 ++++++++
 drivers/pci/controller/dwc/pcie-qcom.c        | 164 +++-------------
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 136 ++++++++++++-
 .../phy/qualcomm/phy-qcom-qmp-pcs-pcie-v5.h   |  14 ++
 include/dt-bindings/clock/qcom,ipq9574-gcc.h  |   4 +
 8 files changed, 469 insertions(+), 141 deletions(-)

-- 
2.40.1

[PATCH v4 RESEND 1/8] dt-bindings: clock: Add PCIe pipe related clocks for IPQ9574

[Alexandru Gagniuc]

Add defines for the missing PCIe PIPE clocks.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 include/dt-bindings/clock/qcom,ipq9574-gcc.h | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/include/dt-bindings/clock/qcom,ipq9574-gcc.h b/include/dt-bindings/clock/qcom,ipq9574-gcc.h
index 08fd3a37acaa..52123c5a09fa 100644
--- a/include/dt-bindings/clock/qcom,ipq9574-gcc.h
+++ b/include/dt-bindings/clock/qcom,ipq9574-gcc.h
@@ -216,4 +216,8 @@
 #define GCC_CRYPTO_AHB_CLK				207
 #define GCC_USB0_PIPE_CLK				208
 #define GCC_USB0_SLEEP_CLK				209
+#define GCC_PCIE0_PIPE_CLK				210
+#define GCC_PCIE1_PIPE_CLK				211
+#define GCC_PCIE2_PIPE_CLK				212
+#define GCC_PCIE3_PIPE_CLK				213
 #endif
-- 
2.40.1

[PATCH v4 RESEND 2/8] clk: qcom: gcc-ipq9574: Add PCIe pipe clocks

[Alexandru Gagniuc]

The IPQ9574 has four PCIe "pipe" clocks. These clocks are required by
PCIe PHYs. Port the pipe clocks from the downstream 5.4 kernel.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 drivers/clk/qcom/gcc-ipq9574.c | 76 ++++++++++++++++++++++++++++++++++
 1 file changed, 76 insertions(+)

diff --git a/drivers/clk/qcom/gcc-ipq9574.c b/drivers/clk/qcom/gcc-ipq9574.c
index 0a3f846695b8..bc3e17f34295 100644
--- a/drivers/clk/qcom/gcc-ipq9574.c
+++ b/drivers/clk/qcom/gcc-ipq9574.c
@@ -1569,6 +1569,24 @@ static struct clk_regmap_phy_mux pcie0_pipe_clk_src = {
 	},
 };
 
+static struct clk_branch gcc_pcie0_pipe_clk = {
+	.halt_reg = 0x28044,
+	.halt_check = BRANCH_HALT_DELAY,
+	.clkr = {
+		.enable_reg = 0x28044,
+		.enable_mask = BIT(0),
+		.hw.init = &(const struct clk_init_data) {
+			.name = "gcc_pcie0_pipe_clk",
+			.parent_hws = (const struct clk_hw *[]) {
+				&pcie0_pipe_clk_src.clkr.hw
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 static struct clk_regmap_phy_mux pcie1_pipe_clk_src = {
 	.reg = 0x29064,
 	.clkr = {
@@ -1583,6 +1601,24 @@ static struct clk_regmap_phy_mux pcie1_pipe_clk_src = {
 	},
 };
 
+static struct clk_branch gcc_pcie1_pipe_clk = {
+	.halt_reg = 0x29044,
+	.halt_check = BRANCH_HALT_DELAY,
+	.clkr = {
+		.enable_reg = 0x29044,
+		.enable_mask = BIT(0),
+		.hw.init = &(const struct clk_init_data) {
+			.name = "gcc_pcie1_pipe_clk",
+			.parent_hws = (const struct clk_hw *[]) {
+				&pcie1_pipe_clk_src.clkr.hw
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 static struct clk_regmap_phy_mux pcie2_pipe_clk_src = {
 	.reg = 0x2a064,
 	.clkr = {
@@ -1597,6 +1633,24 @@ static struct clk_regmap_phy_mux pcie2_pipe_clk_src = {
 	},
 };
 
+static struct clk_branch gcc_pcie2_pipe_clk = {
+	.halt_reg = 0x2a044,
+	.halt_check = BRANCH_HALT_DELAY,
+	.clkr = {
+		.enable_reg = 0x2a044,
+		.enable_mask = BIT(0),
+		.hw.init = &(const struct clk_init_data) {
+			.name = "gcc_pcie2_pipe_clk",
+			.parent_hws = (const struct clk_hw *[]) {
+				&pcie2_pipe_clk_src.clkr.hw
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 static struct clk_regmap_phy_mux pcie3_pipe_clk_src = {
 	.reg = 0x2b064,
 	.clkr = {
@@ -1611,6 +1665,24 @@ static struct clk_regmap_phy_mux pcie3_pipe_clk_src = {
 	},
 };
 
+static struct clk_branch gcc_pcie3_pipe_clk = {
+	.halt_reg = 0x2b044,
+	.halt_check = BRANCH_HALT_DELAY,
+	.clkr = {
+		.enable_reg = 0x2b044,
+		.enable_mask = BIT(0),
+		.hw.init = &(const struct clk_init_data) {
+			.name = "gcc_pcie3_pipe_clk",
+			.parent_hws = (const struct clk_hw *[]) {
+				&pcie3_pipe_clk_src.clkr.hw
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 static const struct freq_tbl ftbl_pcie_rchng_clk_src[] = {
 	F(24000000, P_XO, 1, 0, 0),
 	F(100000000, P_GPLL0, 8, 0, 0),
@@ -4141,6 +4213,10 @@ static struct clk_regmap *gcc_ipq9574_clks[] = {
 	[GCC_SNOC_PCIE1_1LANE_S_CLK] = &gcc_snoc_pcie1_1lane_s_clk.clkr,
 	[GCC_SNOC_PCIE2_2LANE_S_CLK] = &gcc_snoc_pcie2_2lane_s_clk.clkr,
 	[GCC_SNOC_PCIE3_2LANE_S_CLK] = &gcc_snoc_pcie3_2lane_s_clk.clkr,
+	[GCC_PCIE0_PIPE_CLK] = &gcc_pcie0_pipe_clk.clkr,
+	[GCC_PCIE1_PIPE_CLK] = &gcc_pcie1_pipe_clk.clkr,
+	[GCC_PCIE2_PIPE_CLK] = &gcc_pcie2_pipe_clk.clkr,
+	[GCC_PCIE3_PIPE_CLK] = &gcc_pcie3_pipe_clk.clkr,
 };
 
 static const struct qcom_reset_map gcc_ipq9574_resets[] = {
-- 
2.40.1

[PATCH v4 RESEND 3/8] dt-bindings: PCI: qcom: Add IPQ9574 PCIe controller

[Alexandru Gagniuc]

IPQ9574 has PCIe controllers which are almost identical to IPQ6018.
The difference is that the "iface" clock is replaced by the "snoc",
and "anoc". The "sleep" reset is replaced by an "aux" reset.
Document these differences along with the compatible string.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../devicetree/bindings/pci/qcom,pcie.yaml    | 37 +++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
index cf9a6910b542..ac6d2b1b8702 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
@@ -26,6 +26,7 @@ properties:
           - qcom,pcie-ipq8064-v2
           - qcom,pcie-ipq8074
           - qcom,pcie-ipq8074-gen3
+          - qcom,pcie-ipq9574
           - qcom,pcie-msm8996
           - qcom,pcie-qcs404
           - qcom,pcie-sdm845
@@ -161,6 +162,7 @@ allOf:
             enum:
               - qcom,pcie-ipq6018
               - qcom,pcie-ipq8074-gen3
+              - qcom,pcie-ipq9574
     then:
       properties:
         reg:
@@ -397,6 +399,39 @@ allOf:
             - const: axi_m_sticky # AXI Master Sticky reset
             - const: axi_s_sticky # AXI Slave Sticky reset
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pcie-ipq9574
+    then:
+      properties:
+        clocks:
+          minItems: 4
+          maxItems: 4
+        clock-names:
+          items:
+            - const: axi_m # AXI Master clock
+            - const: axi_s # AXI Slave clock
+            - const: axi_bridge # AXI bridge clock
+            - const: anoc
+            - const: snoc
+            - const: rchng
+        resets:
+          minItems: 8
+          maxItems: 8
+        reset-names:
+          items:
+            - const: pipe # PIPE reset
+            - const: aux # AUX reset
+            - const: sticky # Core Sticky reset
+            - const: axi_m # AXI Master reset
+            - const: axi_s # AXI Slave reset
+            - const: axi_s_sticky # AXI Slave Sticky reset
+            - const: axi_m_sticky # AXI Master Sticky reset
+            - const: ahb # AHB Reset
+
   - if:
       properties:
         compatible:
@@ -507,6 +542,7 @@ allOf:
                 - qcom,pcie-ipq8064v2
                 - qcom,pcie-ipq8074
                 - qcom,pcie-ipq8074-gen3
+                - qcom,pcie-ipq9574
                 - qcom,pcie-qcs404
     then:
       required:
@@ -566,6 +602,7 @@ allOf:
               - qcom,pcie-ipq8064-v2
               - qcom,pcie-ipq8074
               - qcom,pcie-ipq8074-gen3
+              - qcom,pcie-ipq9574
               - qcom,pcie-qcs404
     then:
       properties:
-- 
2.40.1

[PATCH v4 RESEND 4/8] PCI: qcom: Switch to devm_clk_bulk_get_all() API to get the clocks from Devicetree

[Alexandru Gagniuc]

From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

There is no need for the device drivers to validate the clocks defined in
Devicetree. The validation should be performed by the DT schema and the
drivers should just get all the clocks from DT. Right now the driver
hardcodes the clock info and validates them against DT which is redundant.

So use devm_clk_bulk_get_all() that just gets all the clocks defined in DT
and get rid of all static clocks info from the driver. This simplifies the
driver.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[moved clks to struct qcom_pcie to reduce code duplication]
---
 drivers/pci/controller/dwc/pcie-qcom.c | 163 ++++---------------------
 1 file changed, 25 insertions(+), 138 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 14772edcf0d3..ea81ff68d433 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -154,58 +154,42 @@
 #define QCOM_PCIE_LINK_SPEED_TO_BW(speed) \
 		Mbps_to_icc(PCIE_SPEED2MBS_ENC(pcie_link_speed[speed]))
 
-#define QCOM_PCIE_1_0_0_MAX_CLOCKS		4
 struct qcom_pcie_resources_1_0_0 {
-	struct clk_bulk_data clks[QCOM_PCIE_1_0_0_MAX_CLOCKS];
 	struct reset_control *core;
 	struct regulator *vdda;
 };
 
-#define QCOM_PCIE_2_1_0_MAX_CLOCKS		5
 #define QCOM_PCIE_2_1_0_MAX_RESETS		6
 #define QCOM_PCIE_2_1_0_MAX_SUPPLY		3
 struct qcom_pcie_resources_2_1_0 {
-	struct clk_bulk_data clks[QCOM_PCIE_2_1_0_MAX_CLOCKS];
 	struct reset_control_bulk_data resets[QCOM_PCIE_2_1_0_MAX_RESETS];
 	int num_resets;
 	struct regulator_bulk_data supplies[QCOM_PCIE_2_1_0_MAX_SUPPLY];
 };
 
-#define QCOM_PCIE_2_3_2_MAX_CLOCKS		4
 #define QCOM_PCIE_2_3_2_MAX_SUPPLY		2
 struct qcom_pcie_resources_2_3_2 {
-	struct clk_bulk_data clks[QCOM_PCIE_2_3_2_MAX_CLOCKS];
 	struct regulator_bulk_data supplies[QCOM_PCIE_2_3_2_MAX_SUPPLY];
 };
 
-#define QCOM_PCIE_2_3_3_MAX_CLOCKS		5
 #define QCOM_PCIE_2_3_3_MAX_RESETS		7
 struct qcom_pcie_resources_2_3_3 {
-	struct clk_bulk_data clks[QCOM_PCIE_2_3_3_MAX_CLOCKS];
 	struct reset_control_bulk_data rst[QCOM_PCIE_2_3_3_MAX_RESETS];
 };
 
-#define QCOM_PCIE_2_4_0_MAX_CLOCKS		4
 #define QCOM_PCIE_2_4_0_MAX_RESETS		12
 struct qcom_pcie_resources_2_4_0 {
-	struct clk_bulk_data clks[QCOM_PCIE_2_4_0_MAX_CLOCKS];
-	int num_clks;
 	struct reset_control_bulk_data resets[QCOM_PCIE_2_4_0_MAX_RESETS];
 	int num_resets;
 };
 
-#define QCOM_PCIE_2_7_0_MAX_CLOCKS		15
 #define QCOM_PCIE_2_7_0_MAX_SUPPLIES		2
 struct qcom_pcie_resources_2_7_0 {
-	struct clk_bulk_data clks[QCOM_PCIE_2_7_0_MAX_CLOCKS];
-	int num_clks;
 	struct regulator_bulk_data supplies[QCOM_PCIE_2_7_0_MAX_SUPPLIES];
 	struct reset_control *rst;
 };
 
-#define QCOM_PCIE_2_9_0_MAX_CLOCKS		5
 struct qcom_pcie_resources_2_9_0 {
-	struct clk_bulk_data clks[QCOM_PCIE_2_9_0_MAX_CLOCKS];
 	struct reset_control *rst;
 };
 
@@ -247,6 +231,8 @@ struct qcom_pcie {
 	struct icc_path *icc_mem;
 	const struct qcom_pcie_cfg *cfg;
 	struct dentry *debugfs;
+	struct clk_bulk_data *clks;
+	int num_clks;
 	bool suspended;
 };
 
@@ -337,22 +323,6 @@ static int qcom_pcie_get_resources_2_1_0(struct qcom_pcie *pcie)
 	if (ret)
 		return ret;
 
-	res->clks[0].id = "iface";
-	res->clks[1].id = "core";
-	res->clks[2].id = "phy";
-	res->clks[3].id = "aux";
-	res->clks[4].id = "ref";
-
-	/* iface, core, phy are required */
-	ret = devm_clk_bulk_get(dev, 3, res->clks);
-	if (ret < 0)
-		return ret;
-
-	/* aux, ref are optional */
-	ret = devm_clk_bulk_get_optional(dev, 2, res->clks + 3);
-	if (ret < 0)
-		return ret;
-
 	res->resets[0].id = "pci";
 	res->resets[1].id = "axi";
 	res->resets[2].id = "ahb";
@@ -373,7 +343,7 @@ static void qcom_pcie_deinit_2_1_0(struct qcom_pcie *pcie)
 {
 	struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
 
-	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
 	reset_control_bulk_assert(res->num_resets, res->resets);
 
 	writel(1, pcie->parf + PARF_PHY_CTRL);
@@ -413,7 +383,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
 
 static int qcom_pcie_post_init_2_1_0(struct qcom_pcie *pcie)
 {
-	struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
 	struct dw_pcie *pci = pcie->pci;
 	struct device *dev = pci->dev;
 	struct device_node *node = dev->of_node;
@@ -425,7 +394,7 @@ static int qcom_pcie_post_init_2_1_0(struct qcom_pcie *pcie)
 	val &= ~PHY_TEST_PWR_DOWN;
 	writel(val, pcie->parf + PARF_PHY_CTRL);
 
-	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
+	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
 	if (ret)
 		return ret;
 
@@ -476,21 +445,11 @@ static int qcom_pcie_get_resources_1_0_0(struct qcom_pcie *pcie)
 	struct qcom_pcie_resources_1_0_0 *res = &pcie->res.v1_0_0;
 	struct dw_pcie *pci = pcie->pci;
 	struct device *dev = pci->dev;
-	int ret;
 
 	res->vdda = devm_regulator_get(dev, "vdda");
 	if (IS_ERR(res->vdda))
 		return PTR_ERR(res->vdda);
 
-	res->clks[0].id = "iface";
-	res->clks[1].id = "aux";
-	res->clks[2].id = "master_bus";
-	res->clks[3].id = "slave_bus";
-
-	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
-	if (ret < 0)
-		return ret;
-
 	res->core = devm_reset_control_get_exclusive(dev, "core");
 	return PTR_ERR_OR_ZERO(res->core);
 }
@@ -500,7 +459,7 @@ static void qcom_pcie_deinit_1_0_0(struct qcom_pcie *pcie)
 	struct qcom_pcie_resources_1_0_0 *res = &pcie->res.v1_0_0;
 
 	reset_control_assert(res->core);
-	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
 	regulator_disable(res->vdda);
 }
 
@@ -517,7 +476,7 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie)
 		return ret;
 	}
 
-	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
+	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
 	if (ret) {
 		dev_err(dev, "cannot prepare/enable clocks\n");
 		goto err_assert_reset;
@@ -532,7 +491,7 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie)
 	return 0;
 
 err_disable_clks:
-	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
 err_assert_reset:
 	reset_control_assert(res->core);
 
@@ -580,15 +539,6 @@ static int qcom_pcie_get_resources_2_3_2(struct qcom_pcie *pcie)
 	if (ret)
 		return ret;
 
-	res->clks[0].id = "aux";
-	res->clks[1].id = "cfg";
-	res->clks[2].id = "bus_master";
-	res->clks[3].id = "bus_slave";
-
-	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
-	if (ret < 0)
-		return ret;
-
 	return 0;
 }
 
@@ -596,7 +546,7 @@ static void qcom_pcie_deinit_2_3_2(struct qcom_pcie *pcie)
 {
 	struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;
 
-	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
 	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
 }
 
@@ -613,7 +563,7 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie)
 		return ret;
 	}
 
-	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
+	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
 	if (ret) {
 		dev_err(dev, "cannot prepare/enable clocks\n");
 		regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
@@ -661,18 +611,6 @@ static int qcom_pcie_get_resources_2_4_0(struct qcom_pcie *pcie)
 	bool is_ipq = of_device_is_compatible(dev->of_node, "qcom,pcie-ipq4019");
 	int ret;
 
-	res->clks[0].id = "aux";
-	res->clks[1].id = "master_bus";
-	res->clks[2].id = "slave_bus";
-	res->clks[3].id = "iface";
-
-	/* qcom,pcie-ipq4019 is defined without "iface" */
-	res->num_clks = is_ipq ? 3 : 4;
-
-	ret = devm_clk_bulk_get(dev, res->num_clks, res->clks);
-	if (ret < 0)
-		return ret;
-
 	res->resets[0].id = "axi_m";
 	res->resets[1].id = "axi_s";
 	res->resets[2].id = "axi_m_sticky";
@@ -700,7 +638,7 @@ static void qcom_pcie_deinit_2_4_0(struct qcom_pcie *pcie)
 	struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0;
 
 	reset_control_bulk_assert(res->num_resets, res->resets);
-	clk_bulk_disable_unprepare(res->num_clks, res->clks);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
 }
 
 static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)
@@ -726,7 +664,7 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)
 
 	usleep_range(10000, 12000);
 
-	ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
+	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
 	if (ret) {
 		reset_control_bulk_assert(res->num_resets, res->resets);
 		return ret;
@@ -742,16 +680,6 @@ static int qcom_pcie_get_resources_2_3_3(struct qcom_pcie *pcie)
 	struct device *dev = pci->dev;
 	int ret;
 
-	res->clks[0].id = "iface";
-	res->clks[1].id = "axi_m";
-	res->clks[2].id = "axi_s";
-	res->clks[3].id = "ahb";
-	res->clks[4].id = "aux";
-
-	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
-	if (ret < 0)
-		return ret;
-
 	res->rst[0].id = "axi_m";
 	res->rst[1].id = "axi_s";
 	res->rst[2].id = "pipe";
@@ -769,9 +697,7 @@ static int qcom_pcie_get_resources_2_3_3(struct qcom_pcie *pcie)
 
 static void qcom_pcie_deinit_2_3_3(struct qcom_pcie *pcie)
 {
-	struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3;
-
-	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
 }
 
 static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
@@ -801,7 +727,7 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
 	 */
 	usleep_range(2000, 2500);
 
-	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
+	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
 	if (ret) {
 		dev_err(dev, "cannot prepare/enable clocks\n");
 		goto err_assert_resets;
@@ -862,8 +788,6 @@ static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie)
 	struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;
 	struct dw_pcie *pci = pcie->pci;
 	struct device *dev = pci->dev;
-	unsigned int num_clks, num_opt_clks;
-	unsigned int idx;
 	int ret;
 
 	res->rst = devm_reset_control_array_get_exclusive(dev);
@@ -877,37 +801,6 @@ static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie)
 	if (ret)
 		return ret;
 
-	idx = 0;
-	res->clks[idx++].id = "aux";
-	res->clks[idx++].id = "cfg";
-	res->clks[idx++].id = "bus_master";
-	res->clks[idx++].id = "bus_slave";
-	res->clks[idx++].id = "slave_q2a";
-
-	num_clks = idx;
-
-	ret = devm_clk_bulk_get(dev, num_clks, res->clks);
-	if (ret < 0)
-		return ret;
-
-	res->clks[idx++].id = "tbu";
-	res->clks[idx++].id = "ddrss_sf_tbu";
-	res->clks[idx++].id = "aggre0";
-	res->clks[idx++].id = "aggre1";
-	res->clks[idx++].id = "noc_aggr";
-	res->clks[idx++].id = "noc_aggr_4";
-	res->clks[idx++].id = "noc_aggr_south_sf";
-	res->clks[idx++].id = "cnoc_qx";
-	res->clks[idx++].id = "sleep";
-	res->clks[idx++].id = "cnoc_sf_axi";
-
-	num_opt_clks = idx - num_clks;
-	res->num_clks = idx;
-
-	ret = devm_clk_bulk_get_optional(dev, num_opt_clks, res->clks + num_clks);
-	if (ret < 0)
-		return ret;
-
 	return 0;
 }
 
@@ -925,7 +818,7 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)
 		return ret;
 	}
 
-	ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
+	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
 	if (ret < 0)
 		goto err_disable_regulators;
 
@@ -977,7 +870,7 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)
 
 	return 0;
 err_disable_clocks:
-	clk_bulk_disable_unprepare(res->num_clks, res->clks);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
 err_disable_regulators:
 	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
 
@@ -1015,7 +908,7 @@ static void qcom_pcie_deinit_2_7_0(struct qcom_pcie *pcie)
 {
 	struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;
 
-	clk_bulk_disable_unprepare(res->num_clks, res->clks);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
 
 	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
 }
@@ -1101,17 +994,6 @@ static int qcom_pcie_get_resources_2_9_0(struct qcom_pcie *pcie)
 	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
 	struct dw_pcie *pci = pcie->pci;
 	struct device *dev = pci->dev;
-	int ret;
-
-	res->clks[0].id = "iface";
-	res->clks[1].id = "axi_m";
-	res->clks[2].id = "axi_s";
-	res->clks[3].id = "axi_bridge";
-	res->clks[4].id = "rchng";
-
-	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
-	if (ret < 0)
-		return ret;
 
 	res->rst = devm_reset_control_array_get_exclusive(dev);
 	if (IS_ERR(res->rst))
@@ -1122,9 +1004,7 @@ static int qcom_pcie_get_resources_2_9_0(struct qcom_pcie *pcie)
 
 static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
 {
-	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
-
-	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
+	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
 }
 
 static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
@@ -1153,7 +1033,7 @@ static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
 
 	usleep_range(2000, 2500);
 
-	return clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
+	return clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
 }
 
 static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
@@ -1561,6 +1441,13 @@ static int qcom_pcie_probe(struct platform_device *pdev)
 		goto err_pm_runtime_put;
 	}
 
+	pcie->num_clks = devm_clk_bulk_get_all(dev, &pcie->clks);
+	if (pcie->num_clks < 0) {
+		ret = pcie->num_clks;
+		dev_err(dev, "Failed to get clocks\n");
+		goto err_pm_runtime_put;
+	}
+
 	ret = qcom_pcie_icc_init(pcie);
 	if (ret)
 		goto err_pm_runtime_put;
-- 
2.40.1

[PATCH v4 RESEND 5/8] PCI: qcom: Add support for IPQ9574

[Alexandru Gagniuc]

IPQ9574 has four PCIe controllers: two single-lane Gen3, and two
dual-lane Gen3. The controllers are identical from a software
perspective, with the differences appearing in the PHYs.

Add a compatible for the PCIe on IPQ9574.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index ea81ff68d433..e61888e6c63d 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -1551,6 +1551,7 @@ static const struct of_device_id qcom_pcie_match[] = {
 	{ .compatible = "qcom,pcie-ipq8064-v2", .data = &cfg_2_1_0 },
 	{ .compatible = "qcom,pcie-ipq8074", .data = &cfg_2_3_3 },
 	{ .compatible = "qcom,pcie-ipq8074-gen3", .data = &cfg_2_9_0 },
+	{ .compatible = "qcom,pcie-ipq9574", .data = &cfg_2_9_0 },
 	{ .compatible = "qcom,pcie-msm8996", .data = &cfg_2_3_2 },
 	{ .compatible = "qcom,pcie-qcs404", .data = &cfg_2_4_0 },
 	{ .compatible = "qcom,pcie-sa8540p", .data = &cfg_sc8280xp },
-- 
2.40.1

[PATCH v4 RESEND 6/8] dt-bindings: phy: qcom,ipq8074-qmp-pcie: add ipq9574 gen3x2 PHY

[Alexandru Gagniuc]

The IPQ9574 gen3x2 PHY is very similar to IPQ6018. It requires the
same parameters as IPQ6018. Add a new compatible string for this PHY.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
---
 .../devicetree/bindings/phy/qcom,ipq8074-qmp-pcie-phy.yaml       | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/phy/qcom,ipq8074-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,ipq8074-qmp-pcie-phy.yaml
index 634cec5d57ea..8a8e23282d1c 100644
--- a/Documentation/devicetree/bindings/phy/qcom,ipq8074-qmp-pcie-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,ipq8074-qmp-pcie-phy.yaml
@@ -19,6 +19,7 @@ properties:
       - qcom,ipq6018-qmp-pcie-phy
       - qcom,ipq8074-qmp-gen3-pcie-phy
       - qcom,ipq8074-qmp-pcie-phy
+      - qcom,ipq9574-qmp-gen3x2-pcie-phy
 
   reg:
     items:
-- 
2.40.1

[PATCH v4 RESEND 7/8] phy: qcom-qmp-pcie: add support for ipq9574 gen3x2 PHY

[Alexandru Gagniuc]

Add support for the gen3x2 PCIe PHY on IPQ9574, ported form downstream
5.4 kernel. Only the serdes and pcs_misc tables are new, the others
being reused from IPQ8074 and IPQ6018 PHYs.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 136 +++++++++++++++++-
 .../phy/qualcomm/phy-qcom-qmp-pcs-pcie-v5.h   |  14 ++
 2 files changed, 149 insertions(+), 1 deletion(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
index 8836bb1ff0cc..055d04d0c9b6 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
@@ -487,6 +487,100 @@ static const struct qmp_phy_init_tbl ipq8074_pcie_gen3_pcs_misc_tbl[] = {
 	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_ENDPOINT_REFCLK_DRIVE, 0xc1),
 };
 
+static const struct qmp_phy_init_tbl ipq9574_gen3x2_pcie_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_PLL_BIAS_EN_CLKBUFLR_EN, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_BIAS_EN_CTRL_BY_PSM, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_SELECT, 0x31),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_IVCO, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_BG_TRIM, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CMN_CONFIG, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP_EN, 0x42),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_RESETSM_CNTRL, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE_MAP, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE_TIMER1, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE_TIMER2, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CORE_CLK_EN, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_HSCLK_SEL, 0x21),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_DEC_START_MODE0, 0x68),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START3_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START2_MODE0, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP2_MODE0, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP1_MODE0, 0xd4),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CP_CTRL_MODE0, 0x09),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_CCTRL_MODE0, 0x28),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN0_MODE0, 0xa0),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE2_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE1_MODE0, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CORE_CLK_EN, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CORECLK_DIV, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_SELECT, 0x32),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SYS_CLK_CTRL, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SYSCLK_BUF_ENABLE, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SYSCLK_EN_SEL, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_BG_TIMER, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_HSCLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_DEC_START_MODE1, 0x53),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START3_MODE1, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START2_MODE1, 0x55),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_DIV_FRAC_START1_MODE1, 0x55),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP2_MODE1, 0x29),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_LOCK_CMP1_MODE1, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CP_CTRL_MODE1, 0x09),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_RCTRL_MODE1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_PLL_CCTRL_MODE1, 0x28),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN1_MODE1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_INTEGLOOP_GAIN0_MODE1, 0xa0),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE2_MODE1, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_VCO_TUNE1_MODE1, 0xb4),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SVS_MODE_CLK_SEL, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CORE_CLK_EN, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CORECLK_DIV_MODE1, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SSC_PER1, 0x7d),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SSC_PER2, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SSC_STEP_SIZE1_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SSC_STEP_SIZE2_MODE0, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SSC_STEP_SIZE1_MODE1, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_SSC_STEP_SIZE2_MODE1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_EP_DIV_MODE0, 0x19),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_EP_DIV_MODE1, 0x28),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_ENABLE1, 0x90),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_HSCLK_SEL, 0x89),
+	QMP_PHY_INIT_CFG(QSERDES_PLL_CLK_ENABLE1, 0x10),
+};
+
+static const struct qmp_phy_init_tbl ipq9574_gen3x2_pcie_pcs_misc_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_OSC_DTCT_ACTIONS, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_POWER_STATE_CONFIG2, 0x1d),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_H, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_L, 0x01),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_H, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_L, 0x01),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_EQ_CONFIG1, 0x14),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_EQ_CONFIG1, 0x10),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_EQ_CONFIG2, 0x0b),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_PRESET_P10_PRE, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_PRESET_P10_POST, 0x58),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_POWER_STATE_CONFIG4, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_OSC_DTCT_CONFIG1, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_OSC_DTCT_CONFIG2, 0x52),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_OSC_DTCT_CONFIG4, 0x19),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_INT_AUX_CLK_CONFIG1, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_OSC_DTCT_MODE2_CONFIG2, 0x49),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_OSC_DTCT_MODE2_CONFIG4, 0x2a),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_OSC_DTCT_MODE2_CONFIG6, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V5_PCS_PCIE_ENDPOINT_REFCLK_DRIVE, 0xc1),
+};
+
 static const struct qmp_phy_init_tbl sdm845_qmp_pcie_serdes_tbl[] = {
 	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x14),
 	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
@@ -2448,7 +2542,7 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
 
 /* list of clocks required by phy */
 static const char * const qmp_pciephy_clk_l[] = {
-	"aux", "cfg_ahb", "ref", "refgen", "rchng", "phy_aux",
+	"aux", "cfg_ahb", "ref", "refgen", "rchng", "phy_aux", "anoc", "snoc"
 };
 
 /* list of regulators */
@@ -2519,6 +2613,16 @@ static const struct qmp_pcie_offsets qmp_pcie_offsets_v4_20 = {
 	.rx2		= 0x0a00,
 };
 
+static const struct qmp_pcie_offsets qmp_pcie_offsets_ipq9574 = {
+	.serdes		= 0,
+	.pcs		= 0x1000,
+	.pcs_misc	= 0x1400,
+	.tx		= 0x0200,
+	.rx		= 0x0400,
+	.tx2		= 0x0600,
+	.rx2		= 0x0800,
+};
+
 static const struct qmp_pcie_offsets qmp_pcie_offsets_v5 = {
 	.serdes		= 0,
 	.pcs		= 0x0200,
@@ -2728,6 +2832,33 @@ static const struct qmp_phy_cfg sm8250_qmp_gen3x1_pciephy_cfg = {
 	.phy_status		= PHYSTATUS,
 };
 
+static const struct qmp_phy_cfg ipq9574_pciephy_gen3x2_cfg = {
+	.lanes			= 2,
+
+	.offsets		= &qmp_pcie_offsets_ipq9574,
+
+	.tbls = {
+		.serdes		= ipq9574_gen3x2_pcie_serdes_tbl,
+		.serdes_num	= ARRAY_SIZE(ipq9574_gen3x2_pcie_serdes_tbl),
+		.tx		= ipq8074_pcie_gen3_tx_tbl,
+		.tx_num		= ARRAY_SIZE(ipq8074_pcie_gen3_tx_tbl),
+		.rx		= ipq6018_pcie_rx_tbl,
+		.rx_num		= ARRAY_SIZE(ipq6018_pcie_rx_tbl),
+		.pcs		= ipq6018_pcie_pcs_tbl,
+		.pcs_num	= ARRAY_SIZE(ipq6018_pcie_pcs_tbl),
+		.pcs_misc	= ipq9574_gen3x2_pcie_pcs_misc_tbl,
+		.pcs_misc_num	= ARRAY_SIZE(ipq9574_gen3x2_pcie_pcs_misc_tbl),
+	},
+	.reset_list		= ipq8074_pciephy_reset_l,
+	.num_resets		= ARRAY_SIZE(ipq8074_pciephy_reset_l),
+	.vreg_list		= NULL,
+	.num_vregs		= 0,
+	.regs			= pciephy_v5_regs_layout,
+
+	.pwrdn_ctrl		= SW_PWRDN | REFCLK_DRV_DSBL,
+	.phy_status		= PHYSTATUS,
+};
+
 static const struct qmp_phy_cfg sm8250_qmp_gen3x2_pciephy_cfg = {
 	.lanes			= 2,
 
@@ -3935,6 +4066,9 @@ static const struct of_device_id qmp_pcie_of_match_table[] = {
 	}, {
 		.compatible = "qcom,ipq8074-qmp-pcie-phy",
 		.data = &ipq8074_pciephy_cfg,
+	}, {
+		.compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy",
+		.data = &ipq9574_pciephy_gen3x2_cfg,
 	}, {
 		.compatible = "qcom,msm8998-qmp-pcie-phy",
 		.data = &msm8998_pciephy_cfg,
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v5.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v5.h
index a469ae2a10a1..fa15a03055de 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v5.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v5.h
@@ -11,8 +11,22 @@
 #define QPHY_V5_PCS_PCIE_POWER_STATE_CONFIG2		0x0c
 #define QPHY_V5_PCS_PCIE_POWER_STATE_CONFIG4		0x14
 #define QPHY_V5_PCS_PCIE_ENDPOINT_REFCLK_DRIVE		0x20
+#define QPHY_V5_PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_L	0x44
+#define QPHY_V5_PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_H	0x48
+#define QPHY_V5_PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_L	0x4c
+#define QPHY_V5_PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_H	0x50
 #define QPHY_V5_PCS_PCIE_INT_AUX_CLK_CONFIG1		0x54
+#define QPHY_V5_PCS_PCIE_OSC_DTCT_CONFIG1		0x5c
+#define QPHY_V5_PCS_PCIE_OSC_DTCT_CONFIG2		0x60
+#define QPHY_V5_PCS_PCIE_OSC_DTCT_CONFIG4		0x68
+#define QPHY_V5_PCS_PCIE_OSC_DTCT_MODE2_CONFIG2		0x7c
+#define QPHY_V5_PCS_PCIE_OSC_DTCT_MODE2_CONFIG4		0x84
+#define QPHY_V5_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5		0x88
+#define QPHY_V5_PCS_PCIE_OSC_DTCT_MODE2_CONFIG6		0x8c
 #define QPHY_V5_PCS_PCIE_OSC_DTCT_ACTIONS		0x94
+#define QPHY_V5_PCS_PCIE_EQ_CONFIG1			0xa4
 #define QPHY_V5_PCS_PCIE_EQ_CONFIG2			0xa8
+#define QPHY_V5_PCS_PCIE_PRESET_P10_PRE			0xc0
+#define QPHY_V5_PCS_PCIE_PRESET_P10_POST		0xe4
 
 #endif
-- 
2.40.1

[PATCH v4 RESEND 8/8] arm64: dts: qcom: ipq9574: add PCIe2 and PCIe3 nodes

[Alexandru Gagniuc]

On ipq9574, there are 4 PCIe controllers. Describe the pcie2 and pcie3
nodes, and their PHYs in devicetree.

The pcie0 and pcie1 controllers use a gen3x1 PHY, which is not
currently supported. Hence, only pcie2 and pcie3 are described. Only
pcie2 was tested because my devboard only has conenctions to pcie2.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
---
 arch/arm64/boot/dts/qcom/ipq9574.dtsi | 178 +++++++++++++++++++++++++-
 1 file changed, 176 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
index 7f2e5cbf3bbb..c391886cf9ab 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
@@ -300,8 +300,8 @@ gcc: clock-controller@1800000 {
 				 <0>,
 				 <0>,
 				 <0>,
-				 <0>,
-				 <0>,
+				 <&pcie2_phy>,
+				 <&pcie3_phy>,
 				 <0>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -745,6 +745,180 @@ frame@b128000 {
 				status = "disabled";
 			};
 		};
+
+		pcie2_phy: phy@8c000 {
+			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+			reg = <0x0008c000 0x14f4>;
+
+			clocks = <&gcc GCC_PCIE2_AUX_CLK>,
+				 <&gcc GCC_PCIE2_AHB_CLK>,
+				 <&gcc GCC_PCIE2_PIPE_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "pipe";
+
+			clock-output-names = "pcie_phy2_pipe_clk";
+			#clock-cells = <0>;
+			#phy-cells = <0>;
+
+			resets = <&gcc GCC_PCIE2_PHY_BCR>,
+				 <&gcc GCC_PCIE2PHY_PHY_BCR>;
+			reset-names = "phy",
+				      "common";
+			status = "disabled";
+		};
+
+		pcie3_phy: phy@f4000 {
+			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+			reg = <0x000f4000 0x14f4>;
+
+			clocks = <&gcc GCC_PCIE3_AUX_CLK>,
+				 <&gcc GCC_PCIE3_AHB_CLK>,
+				 <&gcc GCC_PCIE3_PIPE_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "pipe";
+
+			clock-output-names = "pcie_phy3_pipe_clk";
+			#clock-cells = <0>;
+			#phy-cells = <0>;
+
+			resets = <&gcc GCC_PCIE3_PHY_BCR>,
+				 <&gcc GCC_PCIE3PHY_PHY_BCR>;
+			reset-names = "phy",
+				      "common";
+			status = "disabled";
+		};
+
+		/* TODO: Populate pcie0/pcie1 when gen3x1 phy support is added. */
+
+		pcie2: pcie@20000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg = <0x20000000 0xf1d>,
+			      <0x20000f20 0xa8>,
+			      <0x20001000 0x1000>,
+			      <0x00088000 0x4000>,
+			      <0x20100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+
+			ranges = <0x81000000 0x0 0x20200000 0x20200000 0x0 0x00100000>,
+				 <0x82000000 0x0 0x20300000 0x20300000 0x0 0x07d00000>;
+
+			device_type = "pci";
+			linux,pci-domain = <3>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+			max-link-speed = <3>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			phys = <&pcie2_phy>;
+			phy-names = "pciephy";
+
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 164 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 0 165 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 0 186 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 0 187 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_PCIE2_AXI_M_CLK>,
+				 <&gcc GCC_PCIE2_AXI_S_CLK>,
+				 <&gcc GCC_PCIE2_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
+				 <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>,
+				 <&gcc GCC_PCIE2_RCHNG_CLK>;
+			clock-names = "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng";
+
+			resets = <&gcc GCC_PCIE2_PIPE_ARES>,
+				 <&gcc GCC_PCIE2_AUX_ARES>,
+				 <&gcc GCC_PCIE2_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AXI_M_ARES>,
+				 <&gcc GCC_PCIE2_AXI_S_ARES>,
+				 <&gcc GCC_PCIE2_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AHB_ARES>;
+			reset-names = "pipe",
+				      "aux",
+				      "sticky",
+				      "axi_m",
+				      "axi_s",
+				      "axi_s_sticky",
+				      "axi_m_sticky",
+				      "ahb";
+			status = "disabled";
+		};
+
+		pcie3: pcie@18000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg = <0x18000000 0xf1d>,
+			      <0x18000f20 0xa8>,
+			      <0x18001000 0x1000>,
+			      <0x000f0000 0x4000>,
+			      <0x18100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+
+			ranges = <0x81000000 0x0 0x18200000 0x18200000 0x0 0x00100000>,
+				 <0x82000000 0x0 0x18300000 0x18300000 0x0 0x07d00000>;
+
+			device_type = "pci";
+			linux,pci-domain = <4>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+			max-link-speed = <3>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			phys = <&pcie3_phy>;
+			phy-names = "pciephy";
+
+			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 189 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 0 190 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 0 192 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 0 192 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_PCIE3_AXI_M_CLK>,
+				 <&gcc GCC_PCIE3_AXI_S_CLK>,
+				 <&gcc GCC_PCIE3_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
+				 <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>,
+				 <&gcc GCC_PCIE3_RCHNG_CLK>;
+			clock-names = "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "anoc",
+				      "snoc",
+				      "rchng";
+
+			resets = <&gcc GCC_PCIE3_PIPE_ARES>,
+				 <&gcc GCC_PCIE3_AUX_ARES>,
+				 <&gcc GCC_PCIE3_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AXI_M_ARES>,
+				 <&gcc GCC_PCIE3_AXI_S_ARES>,
+				 <&gcc GCC_PCIE3_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AHB_ARES>;
+			reset-names = "pipe",
+				      "aux",
+				      "sticky",
+				      "axi_m",
+				      "axi_s",
+				      "axi_s_sticky",
+				      "axi_m_sticky",
+				      "ahb";
+			status = "disabled";
+		};
 	};
 
 	thermal-zones {
-- 
2.40.1

Re: [PATCH v4 RESEND 5/8] PCI: qcom: Add support for IPQ9574

[Krzysztof Kozlowski]

On 01/05/2024 06:28, Alexandru Gagniuc wrote:
> IPQ9574 has four PCIe controllers: two single-lane Gen3, and two
> dual-lane Gen3. The controllers are identical from a software
> perspective, with the differences appearing in the PHYs.
> 
> Add a compatible for the PCIe on IPQ9574.

This is a friendly reminder during the review process.

It looks like you received a tag and forgot to add it.

If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions, under or above your Signed-off-by tag. Tag is "received", when
provided in a message replied to you on the mailing list. Tools like b4
can help here. However, there's no need to repost patches *only* to add
the tags. The upstream maintainer will do that for tags received on the
version they apply.

https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577

If a tag was not added on purpose, please state why and what changed.

Best regards,
Krzysztof

Re: [PATCH v4 RESEND 0/8] ipq9574: Enable PCI-Express support

[Krzysztof Kozlowski]

On 01/05/2024 06:28, Alexandru Gagniuc wrote:
> There are four PCIe ports on IPQ9574, pcie0 thru pcie3. This series
> addresses pcie2, which is a gen3x2 port. The board I have only uses
> pcie2, and that's the only one enabled in this series. pcie3 is added
> as a special request, but is untested.
> 
> I believe this makes sense as a monolithic series, as the individual
> pieces are not that useful by themselves.
> 
> In v2, I've had some issues regarding the dt schema checks. For
> transparency, I used the following test invocations to test:
> 
>       make dt_binding_check     DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml
>       make dtbs_check           DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml
> 
> Changes since v3:
>  - "const"ify .hw.init fields for the PCIE pipe clocks
>  - Used pciephy_v5_regs_layout instead of v4 in phy-qcom-qmp-pcie.c
>  - Included Manivannan's patch for qcom-pcie.c clocks
>  - Dropped redundant comments in "ranges" and "interrupt-map" of pcie2.
>  - Added pcie3 and pcie3_phy dts nodes
>  - Moved snoc and anoc clocks to PCIe controller from PHY
> 

Three postings within short time... Allow people to actually review your
code. Please wait 24h before posting new version. Include entire
feedback and all tags. Explain why you ignore/skip some tags.

Best regards,
Krzysztof

Re: [PATCH v4 RESEND 0/8] ipq9574: Enable PCI-Express support

[mr.nuke.me]

On 5/1/24 5:22 AM, Krzysztof Kozlowski wrote:
> On 01/05/2024 06:28, Alexandru Gagniuc wrote:
>> There are four PCIe ports on IPQ9574, pcie0 thru pcie3. This series
>> addresses pcie2, which is a gen3x2 port. The board I have only uses
>> pcie2, and that's the only one enabled in this series. pcie3 is added
>> as a special request, but is untested.
>>
>> I believe this makes sense as a monolithic series, as the individual
>> pieces are not that useful by themselves.
>>
>> In v2, I've had some issues regarding the dt schema checks. For
>> transparency, I used the following test invocations to test:
>>
>>        make dt_binding_check     DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml
>>        make dtbs_check           DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml
>>
>> Changes since v3:
>>   - "const"ify .hw.init fields for the PCIE pipe clocks
>>   - Used pciephy_v5_regs_layout instead of v4 in phy-qcom-qmp-pcie.c
>>   - Included Manivannan's patch for qcom-pcie.c clocks
>>   - Dropped redundant comments in "ranges" and "interrupt-map" of pcie2.
>>   - Added pcie3 and pcie3_phy dts nodes
>>   - Moved snoc and anoc clocks to PCIe controller from PHY
>>
> 
> Three postings within short time... Allow people to actually review your
> code. Please wait 24h before posting new version. Include entire
> feedback and all tags. Explain why you ignore/skip some tags.
> 
I'm sorry for the confusion. It's the same patch version, v3 being two 
weeks old.

Due to a tooling failure, the first attempt to send resulted in a 
double-posting, and missing cover letter. It was so bad that I felt I 
needed to re-post with the RESEND tag to clarify the intent and prevent 
further confusion.

Alex
> 

Re: [PATCH v4 RESEND 5/8] PCI: qcom: Add support for IPQ9574

[mr.nuke.me]

On 5/1/24 5:21 AM, Krzysztof Kozlowski wrote:
> On 01/05/2024 06:28, Alexandru Gagniuc wrote:
>> IPQ9574 has four PCIe controllers: two single-lane Gen3, and two
>> dual-lane Gen3. The controllers are identical from a software
>> perspective, with the differences appearing in the PHYs.
>>
>> Add a compatible for the PCIe on IPQ9574.
> 
> This is a friendly reminder during the review process.
> 
> It looks like you received a tag and forgot to add it.
> 
> If you do not know the process, here is a short explanation:
> Please add Acked-by/Reviewed-by/Tested-by tags when posting new
> versions, under or above your Signed-off-by tag. Tag is "received", when
> provided in a message replied to you on the mailing list. Tools like b4
> can help here. However, there's no need to repost patches *only* to add
> the tags. The upstream maintainer will do that for tags received on the
> version they apply.
> 
> https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
> 
> If a tag was not added on purpose, please state why and what changed.

I had an Acked-by tag from Rob for what is now patch 6/8 -- previously 
5/7. Due to last-minute info from QUIC Inc, Dmitry and I decided to move 
the "snoc" and "anoc" clocks out of the PHY and to the PCIe controller.

This change resulted in a 6/8 patch that is substantially different from 
what Rob acked. I felt it was inappropriate to keep the tag.

Alex

Re: [PATCH v4 RESEND 5/8] PCI: qcom: Add support for IPQ9574

[Krzysztof Kozlowski]

On 01/05/2024 17:43, mr.nuke.me@gmail.com wrote:
> On 5/1/24 5:21 AM, Krzysztof Kozlowski wrote:
>> On 01/05/2024 06:28, Alexandru Gagniuc wrote:
>>> IPQ9574 has four PCIe controllers: two single-lane Gen3, and two
>>> dual-lane Gen3. The controllers are identical from a software
>>> perspective, with the differences appearing in the PHYs.
>>>
>>> Add a compatible for the PCIe on IPQ9574.
>>
>> This is a friendly reminder during the review process.
>>
>> It looks like you received a tag and forgot to add it.
>>
>> If you do not know the process, here is a short explanation:
>> Please add Acked-by/Reviewed-by/Tested-by tags when posting new
>> versions, under or above your Signed-off-by tag. Tag is "received", when
>> provided in a message replied to you on the mailing list. Tools like b4
>> can help here. However, there's no need to repost patches *only* to add
>> the tags. The upstream maintainer will do that for tags received on the
>> version they apply.
>>
>> https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
>>
>> If a tag was not added on purpose, please state why and what changed.
> 
> I had an Acked-by tag from Rob for what is now patch 6/8 -- previously 
> 5/7. Due to last-minute info from QUIC Inc, Dmitry and I decided to move 
> the "snoc" and "anoc" clocks out of the PHY and to the PCIe controller.
> 
> This change resulted in a 6/8 patch that is substantially different from 
> what Rob acked. I felt it was inappropriate to keep the tag.

So please read my message again:
"If a tag was not added on purpose, please state why and what changed."

Your changelog for that patch should say that.


Best regards,
Krzysztof

Re: [PATCH v4 RESEND 8/8] arm64: dts: qcom: ipq9574: add PCIe2 and PCIe3 nodes

[Alex G.]

On 4/30/24 23:28, Alexandru Gagniuc wrote:
> On ipq9574, there are 4 PCIe controllers. Describe the pcie2 and pcie3
> nodes, and their PHYs in devicetree.
> 
> The pcie0 and pcie1 controllers use a gen3x1 PHY, which is not
> currently supported. Hence, only pcie2 and pcie3 are described. Only
> pcie2 was tested because my devboard only has conenctions to pcie2.
> 
> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
> ---
>   arch/arm64/boot/dts/qcom/ipq9574.dtsi | 178 +++++++++++++++++++++++++-
>   1 file changed, 176 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> index 7f2e5cbf3bbb..c391886cf9ab 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> @@ -300,8 +300,8 @@ gcc: clock-controller@1800000 {
>   				 <0>,
>   				 <0>,
>   				 <0>,
> -				 <0>,
> -				 <0>,
> +				 <&pcie2_phy>,
> +				 <&pcie3_phy>,
>   				 <0>;
>   			#clock-cells = <1>;
>   			#reset-cells = <1>;
> @@ -745,6 +745,180 @@ frame@b128000 {
>   				status = "disabled";
>   			};
>   		};
> +
> +		pcie2_phy: phy@8c000 {
> +			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> +			reg = <0x0008c000 0x14f4>;
> +
> +			clocks = <&gcc GCC_PCIE2_AUX_CLK>,
> +				 <&gcc GCC_PCIE2_AHB_CLK>,
> +				 <&gcc GCC_PCIE2_PIPE_CLK>;
> +			clock-names = "aux",
> +				      "cfg_ahb",
> +				      "pipe";
> +
> +			clock-output-names = "pcie_phy2_pipe_clk";
> +			#clock-cells = <0>;
> +			#phy-cells = <0>;
> +
> +			resets = <&gcc GCC_PCIE2_PHY_BCR>,
> +				 <&gcc GCC_PCIE2PHY_PHY_BCR>;
> +			reset-names = "phy",
> +				      "common";
> +			status = "disabled";
> +		};
> +
> +		pcie3_phy: phy@f4000 {
> +			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> +			reg = <0x000f4000 0x14f4>;
> +
> +			clocks = <&gcc GCC_PCIE3_AUX_CLK>,
> +				 <&gcc GCC_PCIE3_AHB_CLK>,
> +				 <&gcc GCC_PCIE3_PIPE_CLK>;
> +			clock-names = "aux",
> +				      "cfg_ahb",
> +				      "pipe";
> +
> +			clock-output-names = "pcie_phy3_pipe_clk";
> +			#clock-cells = <0>;
> +			#phy-cells = <0>;
> +
> +			resets = <&gcc GCC_PCIE3_PHY_BCR>,
> +				 <&gcc GCC_PCIE3PHY_PHY_BCR>;
> +			reset-names = "phy",
> +				      "common";
> +			status = "disabled";
> +		};
> +
> +		/* TODO: Populate pcie0/pcie1 when gen3x1 phy support is added. */
> +
> +		pcie2: pcie@20000000 {
> +			compatible = "qcom,pcie-ipq9574";
> +			reg = <0x20000000 0xf1d>,
> +			      <0x20000f20 0xa8>,
> +			      <0x20001000 0x1000>,
> +			      <0x00088000 0x4000>,
> +			      <0x20100000 0x1000>;
> +			reg-names = "dbi", "elbi", "atu", "parf", "config";
> +
> +			ranges = <0x81000000 0x0 0x20200000 0x20200000 0x0 0x00100000>,
> +				 <0x82000000 0x0 0x20300000 0x20300000 0x0 0x07d00000>;
> +
> +			device_type = "pci";
> +			linux,pci-domain = <3>;
> +			bus-range = <0x00 0xff>;
> +			num-lanes = <2>;
> +			max-link-speed = <3>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			phys = <&pcie2_phy>;
> +			phy-names = "pciephy";
> +
> +			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi";
> +
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc 0 0 164 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 2 &intc 0 0 165 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 3 &intc 0 0 186 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 4 &intc 0 0 187 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			clocks = <&gcc GCC_PCIE2_AXI_M_CLK>,
> +				 <&gcc GCC_PCIE2_AXI_S_CLK>,
> +				 <&gcc GCC_PCIE2_AXI_S_BRIDGE_CLK>,
> +				 <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
> +				 <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>,
> +				 <&gcc GCC_PCIE2_RCHNG_CLK>;
> +			clock-names = "axi_m",
> +				      "axi_s",
> +				      "axi_bridge",
> +				      "rchng";

There is a mistake here with the clock-names :( . Will fix it in v5.

> +
> +			resets = <&gcc GCC_PCIE2_PIPE_ARES>,
> +				 <&gcc GCC_PCIE2_AUX_ARES>,
> +				 <&gcc GCC_PCIE2_CORE_STICKY_ARES>,
> +				 <&gcc GCC_PCIE2_AXI_M_ARES>,
> +				 <&gcc GCC_PCIE2_AXI_S_ARES>,
> +				 <&gcc GCC_PCIE2_AXI_S_STICKY_ARES>,
> +				 <&gcc GCC_PCIE2_AXI_M_STICKY_ARES>,
> +				 <&gcc GCC_PCIE2_AHB_ARES>;
> +			reset-names = "pipe",
> +				      "aux",
> +				      "sticky",
> +				      "axi_m",
> +				      "axi_s",
> +				      "axi_s_sticky",
> +				      "axi_m_sticky",
> +				      "ahb";
> +			status = "disabled";
> +		};
> +
> +		pcie3: pcie@18000000 {
> +			compatible = "qcom,pcie-ipq9574";
> +			reg = <0x18000000 0xf1d>,
> +			      <0x18000f20 0xa8>,
> +			      <0x18001000 0x1000>,
> +			      <0x000f0000 0x4000>,
> +			      <0x18100000 0x1000>;
> +			reg-names = "dbi", "elbi", "atu", "parf", "config";
> +
> +			ranges = <0x81000000 0x0 0x18200000 0x18200000 0x0 0x00100000>,
> +				 <0x82000000 0x0 0x18300000 0x18300000 0x0 0x07d00000>;
> +
> +			device_type = "pci";
> +			linux,pci-domain = <4>;
> +			bus-range = <0x00 0xff>;
> +			num-lanes = <2>;
> +			max-link-speed = <3>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			phys = <&pcie3_phy>;
> +			phy-names = "pciephy";
> +
> +			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi";
> +
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc 0 0 189 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 2 &intc 0 0 190 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 3 &intc 0 0 192 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 4 &intc 0 0 192 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			clocks = <&gcc GCC_PCIE3_AXI_M_CLK>,
> +				 <&gcc GCC_PCIE3_AXI_S_CLK>,
> +				 <&gcc GCC_PCIE3_AXI_S_BRIDGE_CLK>,
> +				 <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
> +				 <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>,
> +				 <&gcc GCC_PCIE3_RCHNG_CLK>;
> +			clock-names = "axi_m",
> +				      "axi_s",
> +				      "axi_bridge",
> +				      "anoc",
> +				      "snoc",
> +				      "rchng";
> +
> +			resets = <&gcc GCC_PCIE3_PIPE_ARES>,
> +				 <&gcc GCC_PCIE3_AUX_ARES>,
> +				 <&gcc GCC_PCIE3_CORE_STICKY_ARES>,
> +				 <&gcc GCC_PCIE3_AXI_M_ARES>,
> +				 <&gcc GCC_PCIE3_AXI_S_ARES>,
> +				 <&gcc GCC_PCIE3_AXI_S_STICKY_ARES>,
> +				 <&gcc GCC_PCIE3_AXI_M_STICKY_ARES>,
> +				 <&gcc GCC_PCIE3_AHB_ARES>;
> +			reset-names = "pipe",
> +				      "aux",
> +				      "sticky",
> +				      "axi_m",
> +				      "axi_s",
> +				      "axi_s_sticky",
> +				      "axi_m_sticky",
> +				      "ahb";
> +			status = "disabled";
> +		};
>   	};
>   
>   	thermal-zones {

Re: [PATCH v4 RESEND 0/8] ipq9574: Enable PCI-Express support

[Devi Priya]

On 5/1/2024 9:58 AM, Alexandru Gagniuc wrote:
> There are four PCIe ports on IPQ9574, pcie0 thru pcie3. This series
> addresses pcie2, which is a gen3x2 port. The board I have only uses
> pcie2, and that's the only one enabled in this series. pcie3 is added
> as a special request, but is untested.
> 
> I believe this makes sense as a monolithic series, as the individual
> pieces are not that useful by themselves.

Hi Alexandru,

As Dmitry suggested, we are working on enabling the PCIe NOC clocks
via Interconnect. We will be posting the PCIe series with
Interconnect support [1] shortly.

[1] - 
https://lore.kernel.org/linux-arm-msm/20240430064214.2030013-1-quic_varada@quicinc.com/

Thanks,
S.Devi Priya
> 
> In v2, I've had some issues regarding the dt schema checks. For
> transparency, I used the following test invocations to test:
> 
>        make dt_binding_check     DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml
>        make dtbs_check           DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml
> 
> Changes since v3:
>   - "const"ify .hw.init fields for the PCIE pipe clocks
>   - Used pciephy_v5_regs_layout instead of v4 in phy-qcom-qmp-pcie.c
>   - Included Manivannan's patch for qcom-pcie.c clocks
>   - Dropped redundant comments in "ranges" and "interrupt-map" of pcie2.
>   - Added pcie3 and pcie3_phy dts nodes
>   - Moved snoc and anoc clocks to PCIe controller from PHY
> 
> Changes since v2:
>   - reworked resets in qcom,pcie.yaml to resolve dt schema errors
>   - constrained "reg" in qcom,pcie.yaml
>   - reworked min/max intems in qcom,ipq8074-qmp-pcie-phy.yaml
>   - dropped msi-parent for pcie node, as it is handled by "msi" IRQ
> 
> Changes since v1:
>   - updated new tables in phy-qcom-qmp-pcie.c to use lowercase hex numbers
>   - reorganized qcom,ipq8074-qmp-pcie-phy.yaml to use a single list of clocks
>   - reorganized qcom,pcie.yaml to include clocks+resets per compatible
>   - Renamed "pcie2_qmp_phy" label to "pcie2_phy"
>   - moved "ranges" property of pcie@20000000 higher up
> 
> Alexandru Gagniuc (7):
>    dt-bindings: clock: Add PCIe pipe related clocks for IPQ9574
>    clk: qcom: gcc-ipq9574: Add PCIe pipe clocks
>    dt-bindings: PCI: qcom: Add IPQ9574 PCIe controller
>    PCI: qcom: Add support for IPQ9574
>    dt-bindings: phy: qcom,ipq8074-qmp-pcie: add ipq9574 gen3x2 PHY
>    phy: qcom-qmp-pcie: add support for ipq9574 gen3x2 PHY
>    arm64: dts: qcom: ipq9574: add PCIe2 and PCIe3 nodes
> 
> Manivannan Sadhasivam (1):
>    PCI: qcom: Switch to devm_clk_bulk_get_all() API to get the clocks
>      from Devicetree
> 
>   .../devicetree/bindings/pci/qcom,pcie.yaml    |  37 ++++
>   .../phy/qcom,ipq8074-qmp-pcie-phy.yaml        |   1 +
>   arch/arm64/boot/dts/qcom/ipq9574.dtsi         | 178 +++++++++++++++++-
>   drivers/clk/qcom/gcc-ipq9574.c                |  76 ++++++++
>   drivers/pci/controller/dwc/pcie-qcom.c        | 164 +++-------------
>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 136 ++++++++++++-
>   .../phy/qualcomm/phy-qcom-qmp-pcs-pcie-v5.h   |  14 ++
>   include/dt-bindings/clock/qcom,ipq9574-gcc.h  |   4 +
>   8 files changed, 469 insertions(+), 141 deletions(-)
> 

Re: [PATCH v4 RESEND 0/8] ipq9574: Enable PCI-Express support

[mr.nuke.me]

On 5/8/24 1:16 AM, Devi Priya wrote:
> 
> 
> On 5/1/2024 9:58 AM, Alexandru Gagniuc wrote:
>> There are four PCIe ports on IPQ9574, pcie0 thru pcie3. This series
>> addresses pcie2, which is a gen3x2 port. The board I have only uses
>> pcie2, and that's the only one enabled in this series. pcie3 is added
>> as a special request, but is untested.
>>
>> I believe this makes sense as a monolithic series, as the individual
>> pieces are not that useful by themselves.
> 
> Hi Alexandru,
> 
> As Dmitry suggested, we are working on enabling the PCIe NOC clocks
> via Interconnect. We will be posting the PCIe series with
> Interconnect support [1] shortly.

I am generally very hesitant to depend on unmerged series, as this can 
cause undue delays. In this particular case, I considered that both 
series can continue to stay independent, with the ability to convert the 
PCIe users to the new clock scheme when the time is right.

> [1] - 
> https://lore.kernel.org/linux-arm-msm/20240430064214.2030013-1-quic_varada@quicinc.com/

What changes would be needed to this series to make use of this? How 
does one use the "interconnected" clocks?

Alex

> Thanks,
> S.Devi Priya
>>
>> In v2, I've had some issues regarding the dt schema checks. For
>> transparency, I used the following test invocations to test:
>>
>>        make dt_binding_check     
>> DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml
>>        make dtbs_check           
>> DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml
>>
>> Changes since v3:
>>   - "const"ify .hw.init fields for the PCIE pipe clocks
>>   - Used pciephy_v5_regs_layout instead of v4 in phy-qcom-qmp-pcie.c
>>   - Included Manivannan's patch for qcom-pcie.c clocks
>>   - Dropped redundant comments in "ranges" and "interrupt-map" of pcie2.
>>   - Added pcie3 and pcie3_phy dts nodes
>>   - Moved snoc and anoc clocks to PCIe controller from PHY
>>
>> Changes since v2:
>>   - reworked resets in qcom,pcie.yaml to resolve dt schema errors
>>   - constrained "reg" in qcom,pcie.yaml
>>   - reworked min/max intems in qcom,ipq8074-qmp-pcie-phy.yaml
>>   - dropped msi-parent for pcie node, as it is handled by "msi" IRQ
>>
>> Changes since v1:
>>   - updated new tables in phy-qcom-qmp-pcie.c to use lowercase hex 
>> numbers
>>   - reorganized qcom,ipq8074-qmp-pcie-phy.yaml to use a single list of 
>> clocks
>>   - reorganized qcom,pcie.yaml to include clocks+resets per compatible
>>   - Renamed "pcie2_qmp_phy" label to "pcie2_phy"
>>   - moved "ranges" property of pcie@20000000 higher up
>>
>> Alexandru Gagniuc (7):
>>    dt-bindings: clock: Add PCIe pipe related clocks for IPQ9574
>>    clk: qcom: gcc-ipq9574: Add PCIe pipe clocks
>>    dt-bindings: PCI: qcom: Add IPQ9574 PCIe controller
>>    PCI: qcom: Add support for IPQ9574
>>    dt-bindings: phy: qcom,ipq8074-qmp-pcie: add ipq9574 gen3x2 PHY
>>    phy: qcom-qmp-pcie: add support for ipq9574 gen3x2 PHY
>>    arm64: dts: qcom: ipq9574: add PCIe2 and PCIe3 nodes
>>
>> Manivannan Sadhasivam (1):
>>    PCI: qcom: Switch to devm_clk_bulk_get_all() API to get the clocks
>>      from Devicetree
>>
>>   .../devicetree/bindings/pci/qcom,pcie.yaml    |  37 ++++
>>   .../phy/qcom,ipq8074-qmp-pcie-phy.yaml        |   1 +
>>   arch/arm64/boot/dts/qcom/ipq9574.dtsi         | 178 +++++++++++++++++-
>>   drivers/clk/qcom/gcc-ipq9574.c                |  76 ++++++++
>>   drivers/pci/controller/dwc/pcie-qcom.c        | 164 +++-------------
>>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 136 ++++++++++++-
>>   .../phy/qualcomm/phy-qcom-qmp-pcs-pcie-v5.h   |  14 ++
>>   include/dt-bindings/clock/qcom,ipq9574-gcc.h  |   4 +
>>   8 files changed, 469 insertions(+), 141 deletions(-)
>>

Re: [PATCH v4 RESEND 4/8] PCI: qcom: Switch to devm_clk_bulk_get_all() API to get the clocks from Devicetree

[Manivannan Sadhasivam]

On Tue, Apr 30, 2024 at 11:28:43PM -0500, Alexandru Gagniuc wrote:
> From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> 
> There is no need for the device drivers to validate the clocks defined in
> Devicetree. The validation should be performed by the DT schema and the
> drivers should just get all the clocks from DT. Right now the driver
> hardcodes the clock info and validates them against DT which is redundant.
> 
> So use devm_clk_bulk_get_all() that just gets all the clocks defined in DT
> and get rid of all static clocks info from the driver. This simplifies the
> driver.
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
> [moved clks to struct qcom_pcie to reduce code duplication]

Can you please revert to my original patch? Even though moving the
devm_clk_bulk_get_all() API to probe saves few LOC, it also makes the resource
handling code scattered across the driver. So I'd like to keep all the resource
handling within the get_resources() callback.

- Mani

> ---
>  drivers/pci/controller/dwc/pcie-qcom.c | 163 ++++---------------------
>  1 file changed, 25 insertions(+), 138 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index 14772edcf0d3..ea81ff68d433 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -154,58 +154,42 @@
>  #define QCOM_PCIE_LINK_SPEED_TO_BW(speed) \
>  		Mbps_to_icc(PCIE_SPEED2MBS_ENC(pcie_link_speed[speed]))
>  
> -#define QCOM_PCIE_1_0_0_MAX_CLOCKS		4
>  struct qcom_pcie_resources_1_0_0 {
> -	struct clk_bulk_data clks[QCOM_PCIE_1_0_0_MAX_CLOCKS];
>  	struct reset_control *core;
>  	struct regulator *vdda;
>  };
>  
> -#define QCOM_PCIE_2_1_0_MAX_CLOCKS		5
>  #define QCOM_PCIE_2_1_0_MAX_RESETS		6
>  #define QCOM_PCIE_2_1_0_MAX_SUPPLY		3
>  struct qcom_pcie_resources_2_1_0 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_1_0_MAX_CLOCKS];
>  	struct reset_control_bulk_data resets[QCOM_PCIE_2_1_0_MAX_RESETS];
>  	int num_resets;
>  	struct regulator_bulk_data supplies[QCOM_PCIE_2_1_0_MAX_SUPPLY];
>  };
>  
> -#define QCOM_PCIE_2_3_2_MAX_CLOCKS		4
>  #define QCOM_PCIE_2_3_2_MAX_SUPPLY		2
>  struct qcom_pcie_resources_2_3_2 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_3_2_MAX_CLOCKS];
>  	struct regulator_bulk_data supplies[QCOM_PCIE_2_3_2_MAX_SUPPLY];
>  };
>  
> -#define QCOM_PCIE_2_3_3_MAX_CLOCKS		5
>  #define QCOM_PCIE_2_3_3_MAX_RESETS		7
>  struct qcom_pcie_resources_2_3_3 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_3_3_MAX_CLOCKS];
>  	struct reset_control_bulk_data rst[QCOM_PCIE_2_3_3_MAX_RESETS];
>  };
>  
> -#define QCOM_PCIE_2_4_0_MAX_CLOCKS		4
>  #define QCOM_PCIE_2_4_0_MAX_RESETS		12
>  struct qcom_pcie_resources_2_4_0 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_4_0_MAX_CLOCKS];
> -	int num_clks;
>  	struct reset_control_bulk_data resets[QCOM_PCIE_2_4_0_MAX_RESETS];
>  	int num_resets;
>  };
>  
> -#define QCOM_PCIE_2_7_0_MAX_CLOCKS		15
>  #define QCOM_PCIE_2_7_0_MAX_SUPPLIES		2
>  struct qcom_pcie_resources_2_7_0 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_7_0_MAX_CLOCKS];
> -	int num_clks;
>  	struct regulator_bulk_data supplies[QCOM_PCIE_2_7_0_MAX_SUPPLIES];
>  	struct reset_control *rst;
>  };
>  
> -#define QCOM_PCIE_2_9_0_MAX_CLOCKS		5
>  struct qcom_pcie_resources_2_9_0 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_9_0_MAX_CLOCKS];
>  	struct reset_control *rst;
>  };
>  
> @@ -247,6 +231,8 @@ struct qcom_pcie {
>  	struct icc_path *icc_mem;
>  	const struct qcom_pcie_cfg *cfg;
>  	struct dentry *debugfs;
> +	struct clk_bulk_data *clks;
> +	int num_clks;
>  	bool suspended;
>  };
>  
> @@ -337,22 +323,6 @@ static int qcom_pcie_get_resources_2_1_0(struct qcom_pcie *pcie)
>  	if (ret)
>  		return ret;
>  
> -	res->clks[0].id = "iface";
> -	res->clks[1].id = "core";
> -	res->clks[2].id = "phy";
> -	res->clks[3].id = "aux";
> -	res->clks[4].id = "ref";
> -
> -	/* iface, core, phy are required */
> -	ret = devm_clk_bulk_get(dev, 3, res->clks);
> -	if (ret < 0)
> -		return ret;
> -
> -	/* aux, ref are optional */
> -	ret = devm_clk_bulk_get_optional(dev, 2, res->clks + 3);
> -	if (ret < 0)
> -		return ret;
> -
>  	res->resets[0].id = "pci";
>  	res->resets[1].id = "axi";
>  	res->resets[2].id = "ahb";
> @@ -373,7 +343,7 @@ static void qcom_pcie_deinit_2_1_0(struct qcom_pcie *pcie)
>  {
>  	struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
>  
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  	reset_control_bulk_assert(res->num_resets, res->resets);
>  
>  	writel(1, pcie->parf + PARF_PHY_CTRL);
> @@ -413,7 +383,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
>  
>  static int qcom_pcie_post_init_2_1_0(struct qcom_pcie *pcie)
>  {
> -	struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
>  	struct dw_pcie *pci = pcie->pci;
>  	struct device *dev = pci->dev;
>  	struct device_node *node = dev->of_node;
> @@ -425,7 +394,7 @@ static int qcom_pcie_post_init_2_1_0(struct qcom_pcie *pcie)
>  	val &= ~PHY_TEST_PWR_DOWN;
>  	writel(val, pcie->parf + PARF_PHY_CTRL);
>  
> -	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret)
>  		return ret;
>  
> @@ -476,21 +445,11 @@ static int qcom_pcie_get_resources_1_0_0(struct qcom_pcie *pcie)
>  	struct qcom_pcie_resources_1_0_0 *res = &pcie->res.v1_0_0;
>  	struct dw_pcie *pci = pcie->pci;
>  	struct device *dev = pci->dev;
> -	int ret;
>  
>  	res->vdda = devm_regulator_get(dev, "vdda");
>  	if (IS_ERR(res->vdda))
>  		return PTR_ERR(res->vdda);
>  
> -	res->clks[0].id = "iface";
> -	res->clks[1].id = "aux";
> -	res->clks[2].id = "master_bus";
> -	res->clks[3].id = "slave_bus";
> -
> -	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
> -	if (ret < 0)
> -		return ret;
> -
>  	res->core = devm_reset_control_get_exclusive(dev, "core");
>  	return PTR_ERR_OR_ZERO(res->core);
>  }
> @@ -500,7 +459,7 @@ static void qcom_pcie_deinit_1_0_0(struct qcom_pcie *pcie)
>  	struct qcom_pcie_resources_1_0_0 *res = &pcie->res.v1_0_0;
>  
>  	reset_control_assert(res->core);
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  	regulator_disable(res->vdda);
>  }
>  
> @@ -517,7 +476,7 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie)
>  		return ret;
>  	}
>  
> -	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret) {
>  		dev_err(dev, "cannot prepare/enable clocks\n");
>  		goto err_assert_reset;
> @@ -532,7 +491,7 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie)
>  	return 0;
>  
>  err_disable_clks:
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  err_assert_reset:
>  	reset_control_assert(res->core);
>  
> @@ -580,15 +539,6 @@ static int qcom_pcie_get_resources_2_3_2(struct qcom_pcie *pcie)
>  	if (ret)
>  		return ret;
>  
> -	res->clks[0].id = "aux";
> -	res->clks[1].id = "cfg";
> -	res->clks[2].id = "bus_master";
> -	res->clks[3].id = "bus_slave";
> -
> -	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
> -	if (ret < 0)
> -		return ret;
> -
>  	return 0;
>  }
>  
> @@ -596,7 +546,7 @@ static void qcom_pcie_deinit_2_3_2(struct qcom_pcie *pcie)
>  {
>  	struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;
>  
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
>  }
>  
> @@ -613,7 +563,7 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie)
>  		return ret;
>  	}
>  
> -	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret) {
>  		dev_err(dev, "cannot prepare/enable clocks\n");
>  		regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
> @@ -661,18 +611,6 @@ static int qcom_pcie_get_resources_2_4_0(struct qcom_pcie *pcie)
>  	bool is_ipq = of_device_is_compatible(dev->of_node, "qcom,pcie-ipq4019");
>  	int ret;
>  
> -	res->clks[0].id = "aux";
> -	res->clks[1].id = "master_bus";
> -	res->clks[2].id = "slave_bus";
> -	res->clks[3].id = "iface";
> -
> -	/* qcom,pcie-ipq4019 is defined without "iface" */
> -	res->num_clks = is_ipq ? 3 : 4;
> -
> -	ret = devm_clk_bulk_get(dev, res->num_clks, res->clks);
> -	if (ret < 0)
> -		return ret;
> -
>  	res->resets[0].id = "axi_m";
>  	res->resets[1].id = "axi_s";
>  	res->resets[2].id = "axi_m_sticky";
> @@ -700,7 +638,7 @@ static void qcom_pcie_deinit_2_4_0(struct qcom_pcie *pcie)
>  	struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0;
>  
>  	reset_control_bulk_assert(res->num_resets, res->resets);
> -	clk_bulk_disable_unprepare(res->num_clks, res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  }
>  
>  static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)
> @@ -726,7 +664,7 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)
>  
>  	usleep_range(10000, 12000);
>  
> -	ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret) {
>  		reset_control_bulk_assert(res->num_resets, res->resets);
>  		return ret;
> @@ -742,16 +680,6 @@ static int qcom_pcie_get_resources_2_3_3(struct qcom_pcie *pcie)
>  	struct device *dev = pci->dev;
>  	int ret;
>  
> -	res->clks[0].id = "iface";
> -	res->clks[1].id = "axi_m";
> -	res->clks[2].id = "axi_s";
> -	res->clks[3].id = "ahb";
> -	res->clks[4].id = "aux";
> -
> -	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
> -	if (ret < 0)
> -		return ret;
> -
>  	res->rst[0].id = "axi_m";
>  	res->rst[1].id = "axi_s";
>  	res->rst[2].id = "pipe";
> @@ -769,9 +697,7 @@ static int qcom_pcie_get_resources_2_3_3(struct qcom_pcie *pcie)
>  
>  static void qcom_pcie_deinit_2_3_3(struct qcom_pcie *pcie)
>  {
> -	struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3;
> -
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  }
>  
>  static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
> @@ -801,7 +727,7 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
>  	 */
>  	usleep_range(2000, 2500);
>  
> -	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret) {
>  		dev_err(dev, "cannot prepare/enable clocks\n");
>  		goto err_assert_resets;
> @@ -862,8 +788,6 @@ static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie)
>  	struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;
>  	struct dw_pcie *pci = pcie->pci;
>  	struct device *dev = pci->dev;
> -	unsigned int num_clks, num_opt_clks;
> -	unsigned int idx;
>  	int ret;
>  
>  	res->rst = devm_reset_control_array_get_exclusive(dev);
> @@ -877,37 +801,6 @@ static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie)
>  	if (ret)
>  		return ret;
>  
> -	idx = 0;
> -	res->clks[idx++].id = "aux";
> -	res->clks[idx++].id = "cfg";
> -	res->clks[idx++].id = "bus_master";
> -	res->clks[idx++].id = "bus_slave";
> -	res->clks[idx++].id = "slave_q2a";
> -
> -	num_clks = idx;
> -
> -	ret = devm_clk_bulk_get(dev, num_clks, res->clks);
> -	if (ret < 0)
> -		return ret;
> -
> -	res->clks[idx++].id = "tbu";
> -	res->clks[idx++].id = "ddrss_sf_tbu";
> -	res->clks[idx++].id = "aggre0";
> -	res->clks[idx++].id = "aggre1";
> -	res->clks[idx++].id = "noc_aggr";
> -	res->clks[idx++].id = "noc_aggr_4";
> -	res->clks[idx++].id = "noc_aggr_south_sf";
> -	res->clks[idx++].id = "cnoc_qx";
> -	res->clks[idx++].id = "sleep";
> -	res->clks[idx++].id = "cnoc_sf_axi";
> -
> -	num_opt_clks = idx - num_clks;
> -	res->num_clks = idx;
> -
> -	ret = devm_clk_bulk_get_optional(dev, num_opt_clks, res->clks + num_clks);
> -	if (ret < 0)
> -		return ret;
> -
>  	return 0;
>  }
>  
> @@ -925,7 +818,7 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)
>  		return ret;
>  	}
>  
> -	ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret < 0)
>  		goto err_disable_regulators;
>  
> @@ -977,7 +870,7 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)
>  
>  	return 0;
>  err_disable_clocks:
> -	clk_bulk_disable_unprepare(res->num_clks, res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  err_disable_regulators:
>  	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
>  
> @@ -1015,7 +908,7 @@ static void qcom_pcie_deinit_2_7_0(struct qcom_pcie *pcie)
>  {
>  	struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;
>  
> -	clk_bulk_disable_unprepare(res->num_clks, res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  
>  	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
>  }
> @@ -1101,17 +994,6 @@ static int qcom_pcie_get_resources_2_9_0(struct qcom_pcie *pcie)
>  	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
>  	struct dw_pcie *pci = pcie->pci;
>  	struct device *dev = pci->dev;
> -	int ret;
> -
> -	res->clks[0].id = "iface";
> -	res->clks[1].id = "axi_m";
> -	res->clks[2].id = "axi_s";
> -	res->clks[3].id = "axi_bridge";
> -	res->clks[4].id = "rchng";
> -
> -	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
> -	if (ret < 0)
> -		return ret;
>  
>  	res->rst = devm_reset_control_array_get_exclusive(dev);
>  	if (IS_ERR(res->rst))
> @@ -1122,9 +1004,7 @@ static int qcom_pcie_get_resources_2_9_0(struct qcom_pcie *pcie)
>  
>  static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
>  {
> -	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> -
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  }
>  
>  static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
> @@ -1153,7 +1033,7 @@ static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
>  
>  	usleep_range(2000, 2500);
>  
> -	return clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	return clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  }
>  
>  static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
> @@ -1561,6 +1441,13 @@ static int qcom_pcie_probe(struct platform_device *pdev)
>  		goto err_pm_runtime_put;
>  	}
>  
> +	pcie->num_clks = devm_clk_bulk_get_all(dev, &pcie->clks);
> +	if (pcie->num_clks < 0) {
> +		ret = pcie->num_clks;
> +		dev_err(dev, "Failed to get clocks\n");
> +		goto err_pm_runtime_put;
> +	}
> +
>  	ret = qcom_pcie_icc_init(pcie);
>  	if (ret)
>  		goto err_pm_runtime_put;
> -- 
> 2.40.1
> 

-- 
மணிவண்ணன் சதாசிவம்

Re: [PATCH v4 RESEND 5/8] PCI: qcom: Add support for IPQ9574

[Manivannan Sadhasivam]

On Tue, Apr 30, 2024 at 11:28:44PM -0500, Alexandru Gagniuc wrote:
> IPQ9574 has four PCIe controllers: two single-lane Gen3, and two
> dual-lane Gen3. The controllers are identical from a software

You mean to say, 'identical to IPQ8074 Gen3 platform' since you are reusing the
2_9_0 cfg?

> perspective, with the differences appearing in the PHYs.
> 
> Add a compatible for the PCIe on IPQ9574.
> 
> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>

But the change looks good to me.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

- Mani

> ---
>  drivers/pci/controller/dwc/pcie-qcom.c | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index ea81ff68d433..e61888e6c63d 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -1551,6 +1551,7 @@ static const struct of_device_id qcom_pcie_match[] = {
>  	{ .compatible = "qcom,pcie-ipq8064-v2", .data = &cfg_2_1_0 },
>  	{ .compatible = "qcom,pcie-ipq8074", .data = &cfg_2_3_3 },
>  	{ .compatible = "qcom,pcie-ipq8074-gen3", .data = &cfg_2_9_0 },
> +	{ .compatible = "qcom,pcie-ipq9574", .data = &cfg_2_9_0 },
>  	{ .compatible = "qcom,pcie-msm8996", .data = &cfg_2_3_2 },
>  	{ .compatible = "qcom,pcie-qcs404", .data = &cfg_2_4_0 },
>  	{ .compatible = "qcom,pcie-sa8540p", .data = &cfg_sc8280xp },
> -- 
> 2.40.1
> 

-- 
மணிவண்ணன் சதாசிவம்

Re: [PATCH v4 RESEND 0/8] ipq9574: Enable PCI-Express support

[Devi Priya]

On 5/8/2024 10:40 PM, mr.nuke.me@gmail.com wrote:
> On 5/8/24 1:16 AM, Devi Priya wrote:
>>
>>
>> On 5/1/2024 9:58 AM, Alexandru Gagniuc wrote:
>>> There are four PCIe ports on IPQ9574, pcie0 thru pcie3. This series
>>> addresses pcie2, which is a gen3x2 port. The board I have only uses
>>> pcie2, and that's the only one enabled in this series. pcie3 is added
>>> as a special request, but is untested.
>>>
>>> I believe this makes sense as a monolithic series, as the individual
>>> pieces are not that useful by themselves.
>>
>> Hi Alexandru,
>>
>> As Dmitry suggested, we are working on enabling the PCIe NOC clocks
>> via Interconnect. We will be posting the PCIe series with
>> Interconnect support [1] shortly.
> 
> I am generally very hesitant to depend on unmerged series, as this can 
> cause undue delays. In this particular case, I considered that both 
> series can continue to stay independent, with the ability to convert the 
> PCIe users to the new clock scheme when the time is right.
> 
>> [1] - 
>> https://lore.kernel.org/linux-arm-msm/20240430064214.2030013-1-quic_varada@quicinc.com/
> 
> What changes would be needed to this series to make use of this? How 
> does one use the "interconnected" clocks?
> 
> Alex
Hi Alex,

Please refer to the latest PCIe series which adds support for enabling
the NoC clocks via interconnect.

https://lore.kernel.org/linux-arm-msm/20240512082858.1806694-1-quic_devipriy@quicinc.com/

Thanks & Regards,
S.Devi Priya
> 
>> Thanks,
>> S.Devi Priya
>>>
>>> In v2, I've had some issues regarding the dt schema checks. For
>>> transparency, I used the following test invocations to test:
>>>
>>>        make dt_binding_check 
>>> DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml
>>>        make dtbs_check 
>>> DT_SCHEMA_FILES=qcom,pcie.yaml:qcom,ipq8074-qmp-pcie-phy.yaml
>>>
>>> Changes since v3:
>>>   - "const"ify .hw.init fields for the PCIE pipe clocks
>>>   - Used pciephy_v5_regs_layout instead of v4 in phy-qcom-qmp-pcie.c
>>>   - Included Manivannan's patch for qcom-pcie.c clocks
>>>   - Dropped redundant comments in "ranges" and "interrupt-map" of pcie2.
>>>   - Added pcie3 and pcie3_phy dts nodes
>>>   - Moved snoc and anoc clocks to PCIe controller from PHY
>>>
>>> Changes since v2:
>>>   - reworked resets in qcom,pcie.yaml to resolve dt schema errors
>>>   - constrained "reg" in qcom,pcie.yaml
>>>   - reworked min/max intems in qcom,ipq8074-qmp-pcie-phy.yaml
>>>   - dropped msi-parent for pcie node, as it is handled by "msi" IRQ
>>>
>>> Changes since v1:
>>>   - updated new tables in phy-qcom-qmp-pcie.c to use lowercase hex 
>>> numbers
>>>   - reorganized qcom,ipq8074-qmp-pcie-phy.yaml to use a single list 
>>> of clocks
>>>   - reorganized qcom,pcie.yaml to include clocks+resets per compatible
>>>   - Renamed "pcie2_qmp_phy" label to "pcie2_phy"
>>>   - moved "ranges" property of pcie@20000000 higher up
>>>
>>> Alexandru Gagniuc (7):
>>>    dt-bindings: clock: Add PCIe pipe related clocks for IPQ9574
>>>    clk: qcom: gcc-ipq9574: Add PCIe pipe clocks
>>>    dt-bindings: PCI: qcom: Add IPQ9574 PCIe controller
>>>    PCI: qcom: Add support for IPQ9574
>>>    dt-bindings: phy: qcom,ipq8074-qmp-pcie: add ipq9574 gen3x2 PHY
>>>    phy: qcom-qmp-pcie: add support for ipq9574 gen3x2 PHY
>>>    arm64: dts: qcom: ipq9574: add PCIe2 and PCIe3 nodes
>>>
>>> Manivannan Sadhasivam (1):
>>>    PCI: qcom: Switch to devm_clk_bulk_get_all() API to get the clocks
>>>      from Devicetree
>>>
>>>   .../devicetree/bindings/pci/qcom,pcie.yaml    |  37 ++++
>>>   .../phy/qcom,ipq8074-qmp-pcie-phy.yaml        |   1 +
>>>   arch/arm64/boot/dts/qcom/ipq9574.dtsi         | 178 +++++++++++++++++-
>>>   drivers/clk/qcom/gcc-ipq9574.c                |  76 ++++++++
>>>   drivers/pci/controller/dwc/pcie-qcom.c        | 164 +++-------------
>>>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 136 ++++++++++++-
>>>   .../phy/qualcomm/phy-qcom-qmp-pcs-pcie-v5.h   |  14 ++
>>>   include/dt-bindings/clock/qcom,ipq9574-gcc.h  |   4 +
>>>   8 files changed, 469 insertions(+), 141 deletions(-)
>>>

Re: [PATCH v4 RESEND 4/8] PCI: qcom: Switch to devm_clk_bulk_get_all() API to get the clocks from Devicetree

[Manivannan Sadhasivam]

On Tue, Apr 30, 2024 at 11:28:43PM -0500, Alexandru Gagniuc wrote:
> From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> 
> There is no need for the device drivers to validate the clocks defined in
> Devicetree. The validation should be performed by the DT schema and the
> drivers should just get all the clocks from DT. Right now the driver
> hardcodes the clock info and validates them against DT which is redundant.
> 
> So use devm_clk_bulk_get_all() that just gets all the clocks defined in DT
> and get rid of all static clocks info from the driver. This simplifies the
> driver.
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
> [moved clks to struct qcom_pcie to reduce code duplication]

This patch is already applied to pci tree. So hopefully you can just rebase it
on top of pci/next for next version (it should get updated soon).

- Mani

> ---
>  drivers/pci/controller/dwc/pcie-qcom.c | 163 ++++---------------------
>  1 file changed, 25 insertions(+), 138 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index 14772edcf0d3..ea81ff68d433 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -154,58 +154,42 @@
>  #define QCOM_PCIE_LINK_SPEED_TO_BW(speed) \
>  		Mbps_to_icc(PCIE_SPEED2MBS_ENC(pcie_link_speed[speed]))
>  
> -#define QCOM_PCIE_1_0_0_MAX_CLOCKS		4
>  struct qcom_pcie_resources_1_0_0 {
> -	struct clk_bulk_data clks[QCOM_PCIE_1_0_0_MAX_CLOCKS];
>  	struct reset_control *core;
>  	struct regulator *vdda;
>  };
>  
> -#define QCOM_PCIE_2_1_0_MAX_CLOCKS		5
>  #define QCOM_PCIE_2_1_0_MAX_RESETS		6
>  #define QCOM_PCIE_2_1_0_MAX_SUPPLY		3
>  struct qcom_pcie_resources_2_1_0 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_1_0_MAX_CLOCKS];
>  	struct reset_control_bulk_data resets[QCOM_PCIE_2_1_0_MAX_RESETS];
>  	int num_resets;
>  	struct regulator_bulk_data supplies[QCOM_PCIE_2_1_0_MAX_SUPPLY];
>  };
>  
> -#define QCOM_PCIE_2_3_2_MAX_CLOCKS		4
>  #define QCOM_PCIE_2_3_2_MAX_SUPPLY		2
>  struct qcom_pcie_resources_2_3_2 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_3_2_MAX_CLOCKS];
>  	struct regulator_bulk_data supplies[QCOM_PCIE_2_3_2_MAX_SUPPLY];
>  };
>  
> -#define QCOM_PCIE_2_3_3_MAX_CLOCKS		5
>  #define QCOM_PCIE_2_3_3_MAX_RESETS		7
>  struct qcom_pcie_resources_2_3_3 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_3_3_MAX_CLOCKS];
>  	struct reset_control_bulk_data rst[QCOM_PCIE_2_3_3_MAX_RESETS];
>  };
>  
> -#define QCOM_PCIE_2_4_0_MAX_CLOCKS		4
>  #define QCOM_PCIE_2_4_0_MAX_RESETS		12
>  struct qcom_pcie_resources_2_4_0 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_4_0_MAX_CLOCKS];
> -	int num_clks;
>  	struct reset_control_bulk_data resets[QCOM_PCIE_2_4_0_MAX_RESETS];
>  	int num_resets;
>  };
>  
> -#define QCOM_PCIE_2_7_0_MAX_CLOCKS		15
>  #define QCOM_PCIE_2_7_0_MAX_SUPPLIES		2
>  struct qcom_pcie_resources_2_7_0 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_7_0_MAX_CLOCKS];
> -	int num_clks;
>  	struct regulator_bulk_data supplies[QCOM_PCIE_2_7_0_MAX_SUPPLIES];
>  	struct reset_control *rst;
>  };
>  
> -#define QCOM_PCIE_2_9_0_MAX_CLOCKS		5
>  struct qcom_pcie_resources_2_9_0 {
> -	struct clk_bulk_data clks[QCOM_PCIE_2_9_0_MAX_CLOCKS];
>  	struct reset_control *rst;
>  };
>  
> @@ -247,6 +231,8 @@ struct qcom_pcie {
>  	struct icc_path *icc_mem;
>  	const struct qcom_pcie_cfg *cfg;
>  	struct dentry *debugfs;
> +	struct clk_bulk_data *clks;
> +	int num_clks;
>  	bool suspended;
>  };
>  
> @@ -337,22 +323,6 @@ static int qcom_pcie_get_resources_2_1_0(struct qcom_pcie *pcie)
>  	if (ret)
>  		return ret;
>  
> -	res->clks[0].id = "iface";
> -	res->clks[1].id = "core";
> -	res->clks[2].id = "phy";
> -	res->clks[3].id = "aux";
> -	res->clks[4].id = "ref";
> -
> -	/* iface, core, phy are required */
> -	ret = devm_clk_bulk_get(dev, 3, res->clks);
> -	if (ret < 0)
> -		return ret;
> -
> -	/* aux, ref are optional */
> -	ret = devm_clk_bulk_get_optional(dev, 2, res->clks + 3);
> -	if (ret < 0)
> -		return ret;
> -
>  	res->resets[0].id = "pci";
>  	res->resets[1].id = "axi";
>  	res->resets[2].id = "ahb";
> @@ -373,7 +343,7 @@ static void qcom_pcie_deinit_2_1_0(struct qcom_pcie *pcie)
>  {
>  	struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
>  
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  	reset_control_bulk_assert(res->num_resets, res->resets);
>  
>  	writel(1, pcie->parf + PARF_PHY_CTRL);
> @@ -413,7 +383,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
>  
>  static int qcom_pcie_post_init_2_1_0(struct qcom_pcie *pcie)
>  {
> -	struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
>  	struct dw_pcie *pci = pcie->pci;
>  	struct device *dev = pci->dev;
>  	struct device_node *node = dev->of_node;
> @@ -425,7 +394,7 @@ static int qcom_pcie_post_init_2_1_0(struct qcom_pcie *pcie)
>  	val &= ~PHY_TEST_PWR_DOWN;
>  	writel(val, pcie->parf + PARF_PHY_CTRL);
>  
> -	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret)
>  		return ret;
>  
> @@ -476,21 +445,11 @@ static int qcom_pcie_get_resources_1_0_0(struct qcom_pcie *pcie)
>  	struct qcom_pcie_resources_1_0_0 *res = &pcie->res.v1_0_0;
>  	struct dw_pcie *pci = pcie->pci;
>  	struct device *dev = pci->dev;
> -	int ret;
>  
>  	res->vdda = devm_regulator_get(dev, "vdda");
>  	if (IS_ERR(res->vdda))
>  		return PTR_ERR(res->vdda);
>  
> -	res->clks[0].id = "iface";
> -	res->clks[1].id = "aux";
> -	res->clks[2].id = "master_bus";
> -	res->clks[3].id = "slave_bus";
> -
> -	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
> -	if (ret < 0)
> -		return ret;
> -
>  	res->core = devm_reset_control_get_exclusive(dev, "core");
>  	return PTR_ERR_OR_ZERO(res->core);
>  }
> @@ -500,7 +459,7 @@ static void qcom_pcie_deinit_1_0_0(struct qcom_pcie *pcie)
>  	struct qcom_pcie_resources_1_0_0 *res = &pcie->res.v1_0_0;
>  
>  	reset_control_assert(res->core);
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  	regulator_disable(res->vdda);
>  }
>  
> @@ -517,7 +476,7 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie)
>  		return ret;
>  	}
>  
> -	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret) {
>  		dev_err(dev, "cannot prepare/enable clocks\n");
>  		goto err_assert_reset;
> @@ -532,7 +491,7 @@ static int qcom_pcie_init_1_0_0(struct qcom_pcie *pcie)
>  	return 0;
>  
>  err_disable_clks:
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  err_assert_reset:
>  	reset_control_assert(res->core);
>  
> @@ -580,15 +539,6 @@ static int qcom_pcie_get_resources_2_3_2(struct qcom_pcie *pcie)
>  	if (ret)
>  		return ret;
>  
> -	res->clks[0].id = "aux";
> -	res->clks[1].id = "cfg";
> -	res->clks[2].id = "bus_master";
> -	res->clks[3].id = "bus_slave";
> -
> -	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
> -	if (ret < 0)
> -		return ret;
> -
>  	return 0;
>  }
>  
> @@ -596,7 +546,7 @@ static void qcom_pcie_deinit_2_3_2(struct qcom_pcie *pcie)
>  {
>  	struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;
>  
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
>  }
>  
> @@ -613,7 +563,7 @@ static int qcom_pcie_init_2_3_2(struct qcom_pcie *pcie)
>  		return ret;
>  	}
>  
> -	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret) {
>  		dev_err(dev, "cannot prepare/enable clocks\n");
>  		regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
> @@ -661,18 +611,6 @@ static int qcom_pcie_get_resources_2_4_0(struct qcom_pcie *pcie)
>  	bool is_ipq = of_device_is_compatible(dev->of_node, "qcom,pcie-ipq4019");
>  	int ret;
>  
> -	res->clks[0].id = "aux";
> -	res->clks[1].id = "master_bus";
> -	res->clks[2].id = "slave_bus";
> -	res->clks[3].id = "iface";
> -
> -	/* qcom,pcie-ipq4019 is defined without "iface" */
> -	res->num_clks = is_ipq ? 3 : 4;
> -
> -	ret = devm_clk_bulk_get(dev, res->num_clks, res->clks);
> -	if (ret < 0)
> -		return ret;
> -
>  	res->resets[0].id = "axi_m";
>  	res->resets[1].id = "axi_s";
>  	res->resets[2].id = "axi_m_sticky";
> @@ -700,7 +638,7 @@ static void qcom_pcie_deinit_2_4_0(struct qcom_pcie *pcie)
>  	struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0;
>  
>  	reset_control_bulk_assert(res->num_resets, res->resets);
> -	clk_bulk_disable_unprepare(res->num_clks, res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  }
>  
>  static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)
> @@ -726,7 +664,7 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)
>  
>  	usleep_range(10000, 12000);
>  
> -	ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret) {
>  		reset_control_bulk_assert(res->num_resets, res->resets);
>  		return ret;
> @@ -742,16 +680,6 @@ static int qcom_pcie_get_resources_2_3_3(struct qcom_pcie *pcie)
>  	struct device *dev = pci->dev;
>  	int ret;
>  
> -	res->clks[0].id = "iface";
> -	res->clks[1].id = "axi_m";
> -	res->clks[2].id = "axi_s";
> -	res->clks[3].id = "ahb";
> -	res->clks[4].id = "aux";
> -
> -	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
> -	if (ret < 0)
> -		return ret;
> -
>  	res->rst[0].id = "axi_m";
>  	res->rst[1].id = "axi_s";
>  	res->rst[2].id = "pipe";
> @@ -769,9 +697,7 @@ static int qcom_pcie_get_resources_2_3_3(struct qcom_pcie *pcie)
>  
>  static void qcom_pcie_deinit_2_3_3(struct qcom_pcie *pcie)
>  {
> -	struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3;
> -
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  }
>  
>  static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
> @@ -801,7 +727,7 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
>  	 */
>  	usleep_range(2000, 2500);
>  
> -	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret) {
>  		dev_err(dev, "cannot prepare/enable clocks\n");
>  		goto err_assert_resets;
> @@ -862,8 +788,6 @@ static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie)
>  	struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;
>  	struct dw_pcie *pci = pcie->pci;
>  	struct device *dev = pci->dev;
> -	unsigned int num_clks, num_opt_clks;
> -	unsigned int idx;
>  	int ret;
>  
>  	res->rst = devm_reset_control_array_get_exclusive(dev);
> @@ -877,37 +801,6 @@ static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie)
>  	if (ret)
>  		return ret;
>  
> -	idx = 0;
> -	res->clks[idx++].id = "aux";
> -	res->clks[idx++].id = "cfg";
> -	res->clks[idx++].id = "bus_master";
> -	res->clks[idx++].id = "bus_slave";
> -	res->clks[idx++].id = "slave_q2a";
> -
> -	num_clks = idx;
> -
> -	ret = devm_clk_bulk_get(dev, num_clks, res->clks);
> -	if (ret < 0)
> -		return ret;
> -
> -	res->clks[idx++].id = "tbu";
> -	res->clks[idx++].id = "ddrss_sf_tbu";
> -	res->clks[idx++].id = "aggre0";
> -	res->clks[idx++].id = "aggre1";
> -	res->clks[idx++].id = "noc_aggr";
> -	res->clks[idx++].id = "noc_aggr_4";
> -	res->clks[idx++].id = "noc_aggr_south_sf";
> -	res->clks[idx++].id = "cnoc_qx";
> -	res->clks[idx++].id = "sleep";
> -	res->clks[idx++].id = "cnoc_sf_axi";
> -
> -	num_opt_clks = idx - num_clks;
> -	res->num_clks = idx;
> -
> -	ret = devm_clk_bulk_get_optional(dev, num_opt_clks, res->clks + num_clks);
> -	if (ret < 0)
> -		return ret;
> -
>  	return 0;
>  }
>  
> @@ -925,7 +818,7 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)
>  		return ret;
>  	}
>  
> -	ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  	if (ret < 0)
>  		goto err_disable_regulators;
>  
> @@ -977,7 +870,7 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)
>  
>  	return 0;
>  err_disable_clocks:
> -	clk_bulk_disable_unprepare(res->num_clks, res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  err_disable_regulators:
>  	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
>  
> @@ -1015,7 +908,7 @@ static void qcom_pcie_deinit_2_7_0(struct qcom_pcie *pcie)
>  {
>  	struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;
>  
> -	clk_bulk_disable_unprepare(res->num_clks, res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  
>  	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
>  }
> @@ -1101,17 +994,6 @@ static int qcom_pcie_get_resources_2_9_0(struct qcom_pcie *pcie)
>  	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
>  	struct dw_pcie *pci = pcie->pci;
>  	struct device *dev = pci->dev;
> -	int ret;
> -
> -	res->clks[0].id = "iface";
> -	res->clks[1].id = "axi_m";
> -	res->clks[2].id = "axi_s";
> -	res->clks[3].id = "axi_bridge";
> -	res->clks[4].id = "rchng";
> -
> -	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
> -	if (ret < 0)
> -		return ret;
>  
>  	res->rst = devm_reset_control_array_get_exclusive(dev);
>  	if (IS_ERR(res->rst))
> @@ -1122,9 +1004,7 @@ static int qcom_pcie_get_resources_2_9_0(struct qcom_pcie *pcie)
>  
>  static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
>  {
> -	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> -
> -	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +	clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
>  }
>  
>  static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
> @@ -1153,7 +1033,7 @@ static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
>  
>  	usleep_range(2000, 2500);
>  
> -	return clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	return clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
>  }
>  
>  static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
> @@ -1561,6 +1441,13 @@ static int qcom_pcie_probe(struct platform_device *pdev)
>  		goto err_pm_runtime_put;
>  	}
>  
> +	pcie->num_clks = devm_clk_bulk_get_all(dev, &pcie->clks);
> +	if (pcie->num_clks < 0) {
> +		ret = pcie->num_clks;
> +		dev_err(dev, "Failed to get clocks\n");
> +		goto err_pm_runtime_put;
> +	}
> +
>  	ret = qcom_pcie_icc_init(pcie);
>  	if (ret)
>  		goto err_pm_runtime_put;
> -- 
> 2.40.1
> 

-- 
மணிவண்ணன் சதாசிவம்