[PATCH V5 0/6] Add PCIe support for IPQ9574

[PATCH V5 0/6] Add PCIe support for IPQ9574

[devi priya]

This series adds support for enabling the PCIe host devices (PCIe0, PCIe1,
PCIe2, PCIe3) found on IPQ9574 platform.
The PCIe0 & PCIe1 are 1-lane Gen3 host and PCIe2 & PCIe3 
are 2-lane Gen3 host.

[V5]
	Change logs are added to the respective patches
	This series depends on the below series which adds support for
	Interconnect driver[1] and fetching clocks from the Device Tree[2]
	[1] - https://lore.kernel.org/linux-arm-msm/20240430064214.2030013-1-quic_varada@quicinc.com/
	[2] - https://lore.kernel.org/linux-pci/20240417-pci-qcom-clk-bulk-v1-1-52ca19b3d6b2@linaro.org/
[V4]
https://lore.kernel.org/linux-arm-msm/20230528142111.GC2814@thinkpad/

[V3]
https://lore.kernel.org/linux-arm-msm/20230421124938.21974-1-quic_devipriy@quicinc.com/
	- Dropped the phy driver and binding patches as they have been 
	  posted as a separate series.
	- Dropped the pinctrl binding fix patch as it is unrelated to the series
	  dt-bindings: pinctrl: qcom: Add few missing functions.
	- Rebased on linux-next/master.
	- Detailed change logs are added to the respective patches.

[V2]
https://lore.kernel.org/linux-arm-msm/20230404164828.8031-1-quic_devipriy@quicinc.com/
	- Reordered the patches and split the board DT changes
	  into a separate patch as suggested
	- Detailed change logs are added to the respective patches
[V1]
https://lore.kernel.org/linux-arm-msm/20230214164135.17039-1-quic_devipriy@quicinc.com/

devi priya (6):
  Add PCIe pipe clock definitions for IPQ9574 SoC.
  clk: qcom: gcc-ipq9574: Add PCIe pipe clocks
  dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller.
  arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes
  arm64: dts: qcom: ipq9574: Enable PCIe PHYs and controllers
  PCI: qcom: Add support for IPQ9574

 .../devicetree/bindings/pci/qcom,pcie.yaml    |  37 ++
 arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts   | 113 ++++++
 arch/arm64/boot/dts/qcom/ipq9574.dtsi         | 365 +++++++++++++++++-
 drivers/clk/qcom/gcc-ipq9574.c                |  76 ++++
 drivers/pci/controller/dwc/pcie-qcom.c        |  36 +-
 include/dt-bindings/clock/qcom,ipq9574-gcc.h  |   4 +
 6 files changed, 623 insertions(+), 8 deletions(-)


base-commit: e7b4ef8fffaca247809337bb78daceb406659f2d
prerequisite-patch-id: 513cb089a74b49996b46345595d1aacf60dcda64
prerequisite-patch-id: ce7a8e9bac53fd5f02921bff6bc54149fb92f996
prerequisite-patch-id: c26478e61e583eb879385598f26b42b8271036f5
prerequisite-patch-id: a5c15da6a968e673737dc5aa962f31576903f8aa
prerequisite-patch-id: 353eb53cd192489d5b0c4654a0b922f23e1f7217
prerequisite-patch-id: d282ba7948460ae4d2f541c8c25ff5089ff6507e
prerequisite-patch-id: 5141131d46f7789b50ac806f10b63869d15d709f
prerequisite-patch-id: f9d936541ba730ad6383b4ccab85964b853eb241
prerequisite-patch-id: 7382bed435a31877deb5d02dd105cc4b9cf31abc
-- 
2.34.1

[PATCH V5 1/6] Add PCIe pipe clock definitions for IPQ9574 SoC.

[devi priya]

Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
---
 Changes in V5:
	- No changes

 include/dt-bindings/clock/qcom,ipq9574-gcc.h | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/include/dt-bindings/clock/qcom,ipq9574-gcc.h b/include/dt-bindings/clock/qcom,ipq9574-gcc.h
index 08fd3a37acaa..52123c5a09fa 100644
--- a/include/dt-bindings/clock/qcom,ipq9574-gcc.h
+++ b/include/dt-bindings/clock/qcom,ipq9574-gcc.h
@@ -216,4 +216,8 @@
 #define GCC_CRYPTO_AHB_CLK				207
 #define GCC_USB0_PIPE_CLK				208
 #define GCC_USB0_SLEEP_CLK				209
+#define GCC_PCIE0_PIPE_CLK				210
+#define GCC_PCIE1_PIPE_CLK				211
+#define GCC_PCIE2_PIPE_CLK				212
+#define GCC_PCIE3_PIPE_CLK				213
 #endif
-- 
2.34.1

[PATCH V5 2/6] clk: qcom: gcc-ipq9574: Add PCIe pipe clocks

[devi priya]

Add the PCIe pipe clocks needed for enabling PCIe in IPQ9574.

Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
---
 Changes in V5:
	- No changes

 drivers/clk/qcom/gcc-ipq9574.c | 76 ++++++++++++++++++++++++++++++++++
 1 file changed, 76 insertions(+)

diff --git a/drivers/clk/qcom/gcc-ipq9574.c b/drivers/clk/qcom/gcc-ipq9574.c
index 3738f92c6f9c..7d1b9d2468e6 100644
--- a/drivers/clk/qcom/gcc-ipq9574.c
+++ b/drivers/clk/qcom/gcc-ipq9574.c
@@ -1572,6 +1572,24 @@ static struct clk_regmap_phy_mux pcie0_pipe_clk_src = {
 	},
 };
 
+static struct clk_branch gcc_pcie0_pipe_clk = {
+	.halt_reg = 0x28044,
+	.halt_check = BRANCH_HALT_DELAY,
+	.clkr = {
+		.enable_reg = 0x28044,
+		.enable_mask = BIT(0),
+		.hw.init = &(const struct clk_init_data) {
+			.name = "gcc_pcie0_pipe_clk",
+			.parent_hws = (const struct clk_hw *[]) {
+				&pcie0_pipe_clk_src.clkr.hw
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 static struct clk_regmap_phy_mux pcie1_pipe_clk_src = {
 	.reg = 0x29064,
 	.clkr = {
@@ -1586,6 +1604,24 @@ static struct clk_regmap_phy_mux pcie1_pipe_clk_src = {
 	},
 };
 
+static struct clk_branch gcc_pcie1_pipe_clk = {
+	.halt_reg = 0x29044,
+	.halt_check = BRANCH_HALT_DELAY,
+	.clkr = {
+		.enable_reg = 0x29044,
+		.enable_mask = BIT(0),
+		.hw.init = &(const struct clk_init_data) {
+			.name = "gcc_pcie1_pipe_clk",
+			.parent_hws = (const struct clk_hw *[]) {
+				&pcie1_pipe_clk_src.clkr.hw
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 static struct clk_regmap_phy_mux pcie2_pipe_clk_src = {
 	.reg = 0x2a064,
 	.clkr = {
@@ -1600,6 +1636,24 @@ static struct clk_regmap_phy_mux pcie2_pipe_clk_src = {
 	},
 };
 
+static struct clk_branch gcc_pcie2_pipe_clk = {
+	.halt_reg = 0x2a044,
+	.halt_check = BRANCH_HALT_DELAY,
+	.clkr = {
+		.enable_reg = 0x2a044,
+		.enable_mask = BIT(0),
+		.hw.init = &(const struct clk_init_data) {
+			.name = "gcc_pcie2_pipe_clk",
+			.parent_hws = (const struct clk_hw *[]) {
+				&pcie2_pipe_clk_src.clkr.hw
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 static struct clk_regmap_phy_mux pcie3_pipe_clk_src = {
 	.reg = 0x2b064,
 	.clkr = {
@@ -1614,6 +1668,24 @@ static struct clk_regmap_phy_mux pcie3_pipe_clk_src = {
 	},
 };
 
+static struct clk_branch gcc_pcie3_pipe_clk = {
+	.halt_reg = 0x2b044,
+	.halt_check = BRANCH_HALT_DELAY,
+	.clkr = {
+		.enable_reg = 0x2b044,
+		.enable_mask = BIT(0),
+		.hw.init = &(const struct clk_init_data) {
+			.name = "gcc_pcie3_pipe_clk",
+			.parent_hws = (const struct clk_hw *[]) {
+				&pcie3_pipe_clk_src.clkr.hw
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
 static const struct freq_tbl ftbl_pcie_rchng_clk_src[] = {
 	F(24000000, P_XO, 1, 0, 0),
 	F(100000000, P_GPLL0, 8, 0, 0),
@@ -4007,9 +4079,13 @@ static struct clk_regmap *gcc_ipq9574_clks[] = {
 	[GCC_PCIE3_AXI_S_BRIDGE_CLK] = &gcc_pcie3_axi_s_bridge_clk.clkr,
 	[GCC_PCIE3_AXI_S_CLK] = &gcc_pcie3_axi_s_clk.clkr,
 	[PCIE0_PIPE_CLK_SRC] = &pcie0_pipe_clk_src.clkr,
+	[GCC_PCIE0_PIPE_CLK] = &gcc_pcie0_pipe_clk.clkr,
 	[PCIE1_PIPE_CLK_SRC] = &pcie1_pipe_clk_src.clkr,
+	[GCC_PCIE1_PIPE_CLK] = &gcc_pcie1_pipe_clk.clkr,
 	[PCIE2_PIPE_CLK_SRC] = &pcie2_pipe_clk_src.clkr,
+	[GCC_PCIE2_PIPE_CLK] = &gcc_pcie2_pipe_clk.clkr,
 	[PCIE3_PIPE_CLK_SRC] = &pcie3_pipe_clk_src.clkr,
+	[GCC_PCIE3_PIPE_CLK] = &gcc_pcie3_pipe_clk.clkr,
 	[PCIE_AUX_CLK_SRC] = &pcie_aux_clk_src.clkr,
 	[GCC_PCIE0_AUX_CLK] = &gcc_pcie0_aux_clk.clkr,
 	[GCC_PCIE1_AUX_CLK] = &gcc_pcie1_aux_clk.clkr,
-- 
2.34.1

[PATCH V5 3/6] dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller.

[devi priya]

Document the PCIe controller on IPQ9574 platform.

Signed-off-by: devi priya <quic_devipriy@quicinc.com>
---
 Changes in V5:
	- Dropped msi-parent for pcie node, as it is handled by "msi" IRQ

 .../devicetree/bindings/pci/qcom,pcie.yaml    | 37 +++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
index cf9a6910b542..65d4c0c0bcd0 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
@@ -26,6 +26,7 @@ properties:
           - qcom,pcie-ipq8064-v2
           - qcom,pcie-ipq8074
           - qcom,pcie-ipq8074-gen3
+          - qcom,pcie-ipq9574
           - qcom,pcie-msm8996
           - qcom,pcie-qcs404
           - qcom,pcie-sdm845
@@ -161,6 +162,7 @@ allOf:
             enum:
               - qcom,pcie-ipq6018
               - qcom,pcie-ipq8074-gen3
+              - qcom,pcie-ipq9574
     then:
       properties:
         reg:
@@ -397,6 +399,39 @@ allOf:
             - const: axi_m_sticky # AXI Master Sticky reset
             - const: axi_s_sticky # AXI Slave Sticky reset
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pcie-ipq9574
+    then:
+      properties:
+        clocks:
+          minItems: 6
+          maxItems: 6
+        clock-names:
+          items:
+            - const: ahb  # AHB clock
+            - const: aux  # Auxiliary clock
+            - const: axi_m # AXI Master clock
+            - const: axi_s # AXI Slave clock
+            - const: axi_bridge # AXI bridge clock
+            - const: rchng
+        resets:
+          minItems: 8
+          maxItems: 8
+        reset-names:
+          items:
+            - const: pipe # PIPE reset
+            - const: sticky # Core Sticky reset
+            - const: axi_s_sticky # AXI Slave Sticky reset
+            - const: axi_s # AXI Slave reset
+            - const: axi_m_sticky # AXI Master Sticky reset
+            - const: axi_m # AXI Master reset
+            - const: aux # AUX Reset
+            - const: ahb # AHB Reset
+
   - if:
       properties:
         compatible:
@@ -507,6 +542,7 @@ allOf:
                 - qcom,pcie-ipq8064v2
                 - qcom,pcie-ipq8074
                 - qcom,pcie-ipq8074-gen3
+                - qcom,pcie-ipq9574
                 - qcom,pcie-qcs404
     then:
       required:
@@ -566,6 +602,7 @@ allOf:
               - qcom,pcie-ipq8064-v2
               - qcom,pcie-ipq8074
               - qcom,pcie-ipq8074-gen3
+              - qcom,pcie-ipq9574
               - qcom,pcie-qcs404
     then:
       properties:
-- 
2.34.1

[PATCH V5 4/6] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes

[devi priya]

Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.

Signed-off-by: devi priya <quic_devipriy@quicinc.com>
---
 Changes in V5:
	- Dropped anoc and snoc lane clocks from Phy nodes and enabled them
	  via interconnect.
	- Dropped msi-parent as it is handled via msi IRQ

 arch/arm64/boot/dts/qcom/ipq9574.dtsi | 365 +++++++++++++++++++++++++-
 1 file changed, 361 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
index 5b3e69379b1f..da6418c9d52b 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
@@ -226,6 +226,52 @@ rpm_msg_ram: sram@60000 {
 			reg = <0x00060000 0x6000>;
 		};
 
+		pcie0_phy: phy@84000 {
+			compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+			reg = <0x00084000 0x1000>;
+
+			clocks = <&gcc GCC_PCIE0_AUX_CLK>,
+				 <&gcc GCC_PCIE0_AHB_CLK>,
+				 <&gcc GCC_PCIE0_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE0_PHY_BCR>,
+				 <&gcc GCC_PCIE0PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie0_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		pcie2_phy: phy@8c000 {
+			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+			reg = <0x0008c000 0x2000>;
+
+			clocks = <&gcc GCC_PCIE2_AUX_CLK>,
+				 <&gcc GCC_PCIE2_AHB_CLK>,
+				 <&gcc GCC_PCIE2_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE2_PHY_BCR>,
+				 <&gcc GCC_PCIE2PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie2_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		rng: rng@e3000 {
 			compatible = "qcom,prng-ee";
 			reg = <0x000e3000 0x1000>;
@@ -233,6 +279,52 @@ rng: rng@e3000 {
 			clock-names = "core";
 		};
 
+		pcie3_phy: phy@f4000 {
+			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+			reg = <0x000f4000 0x2000>;
+
+			clocks = <&gcc GCC_PCIE3_AUX_CLK>,
+				 <&gcc GCC_PCIE3_AHB_CLK>,
+				 <&gcc GCC_PCIE3_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE3_PHY_BCR>,
+				 <&gcc GCC_PCIE3PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie3_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		pcie1_phy: phy@fc000 {
+			compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+			reg = <0x000fc000 0x1000>;
+
+			clocks = <&gcc GCC_PCIE1_AUX_CLK>,
+				 <&gcc GCC_PCIE1_AHB_CLK>,
+				 <&gcc GCC_PCIE1_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
+			assigned-clock-rates = <20000000>;
+
+			resets = <&gcc GCC_PCIE1_PHY_BCR>,
+				 <&gcc GCC_PCIE1PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <0>;
+			clock-output-names = "gcc_pcie1_pipe_clk_src";
+
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		qfprom: efuse@a4000 {
 			compatible = "qcom,ipq9574-qfprom", "qcom,qfprom";
 			reg = <0x000a4000 0x5a1>;
@@ -299,10 +391,10 @@ gcc: clock-controller@1800000 {
 			clocks = <&xo_board_clk>,
 				 <&sleep_clk>,
 				 <0>,
-				 <0>,
-				 <0>,
-				 <0>,
-				 <0>,
+				 <&pcie0_phy>,
+				 <&pcie1_phy>,
+				 <&pcie2_phy>,
+				 <&pcie3_phy>,
 				 <0>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -747,6 +839,271 @@ frame@b128000 {
 				status = "disabled";
 			};
 		};
+
+		pcie1: pci@10000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x10000000 0xf1d>,
+			       <0x10000F20 0xa8>,
+			       <0x10001000 0x1000>,
+			       <0x000F8000 0x4000>,
+			       <0x10100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <2>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x10200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x10300000 0x10300000 0x0 0x7d00000>; /* MEM */
+
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 35 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 49 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 84 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 85 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			/* clocks and clock-names are used to enable the clock in CBCR */
+			clocks = <&gcc GCC_PCIE1_AHB_CLK>,
+				 <&gcc GCC_PCIE1_AUX_CLK>,
+				 <&gcc GCC_PCIE1_AXI_M_CLK>,
+				 <&gcc GCC_PCIE1_AXI_S_CLK>,
+				 <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE1_RCHNG_CLK>;
+			clock-names = "ahb",
+				      "aux",
+				      "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng";
+
+			resets = <&gcc GCC_PCIE1_PIPE_ARES>,
+				 <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE1_AXI_S_ARES>,
+				 <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE1_AXI_M_ARES>,
+				 <&gcc GCC_PCIE1_AUX_ARES>,
+				 <&gcc GCC_PCIE1_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie1_phy>;
+			phy-names = "pciephy";
+			interconnects = <&gcc MASTER_ANOC_PCIE1 &gcc SLAVE_ANOC_PCIE1>,
+					<&gcc MASTER_SNOC_PCIE1 &gcc SLAVE_SNOC_PCIE1>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+			status = "disabled";
+		};
+
+		pcie3: pci@18000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x18000000 0xf1d>,
+			       <0x18000F20 0xa8>,
+			       <0x18001000 0x1000>,
+			       <0x000F0000 0x4000>,
+			       <0x18100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <4>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x18200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x18300000 0x18300000 0x0 0x7d00000>; /* MEM */
+
+			interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 189 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 190 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 191 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 192 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			/* clocks and clock-names are used to enable the clock in CBCR */
+			clocks = <&gcc GCC_PCIE3_AHB_CLK>,
+				 <&gcc GCC_PCIE3_AUX_CLK>,
+				 <&gcc GCC_PCIE3_AXI_M_CLK>,
+				 <&gcc GCC_PCIE3_AXI_S_CLK>,
+				 <&gcc GCC_PCIE3_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE3_RCHNG_CLK>;
+			clock-names = "ahb",
+				      "aux",
+				      "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng";
+
+			resets = <&gcc GCC_PCIE3_PIPE_ARES>,
+				 <&gcc GCC_PCIE3_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AXI_S_ARES>,
+				 <&gcc GCC_PCIE3_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE3_AXI_M_ARES>,
+				 <&gcc GCC_PCIE3_AUX_ARES>,
+				 <&gcc GCC_PCIE3_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie3_phy>;
+			phy-names = "pciephy";
+			interconnects = <&gcc MASTER_ANOC_PCIE3 &gcc SLAVE_ANOC_PCIE3>,
+					<&gcc MASTER_SNOC_PCIE3 &gcc SLAVE_SNOC_PCIE3>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+			status = "disabled";
+		};
+
+		pcie2: pci@20000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x20000000 0xf1d>,
+			       <0x20000F20 0xa8>,
+			       <0x20001000 0x1000>,
+			       <0x00088000 0x4000>,
+			       <0x20100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <3>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x20200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x20300000 0x20300000 0x0 0x7d00000>; /* MEM */
+
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 164 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 165 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 186 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 187 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			/* clocks and clock-names are used to enable the clock in CBCR */
+			clocks = <&gcc GCC_PCIE2_AHB_CLK>,
+				 <&gcc GCC_PCIE2_AUX_CLK>,
+				 <&gcc GCC_PCIE2_AXI_M_CLK>,
+				 <&gcc GCC_PCIE2_AXI_S_CLK>,
+				 <&gcc GCC_PCIE2_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE2_RCHNG_CLK>;
+			clock-names = "ahb",
+				      "aux",
+				      "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng";
+
+			resets = <&gcc GCC_PCIE2_PIPE_ARES>,
+				 <&gcc GCC_PCIE2_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AXI_S_ARES>,
+				 <&gcc GCC_PCIE2_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE2_AXI_M_ARES>,
+				 <&gcc GCC_PCIE2_AUX_ARES>,
+				 <&gcc GCC_PCIE2_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie2_phy>;
+			phy-names = "pciephy";
+			interconnects = <&gcc MASTER_ANOC_PCIE2 &gcc SLAVE_ANOC_PCIE2>,
+					<&gcc MASTER_SNOC_PCIE2 &gcc SLAVE_SNOC_PCIE2>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+			status = "disabled";
+		};
+
+		pcie0: pci@28000000 {
+			compatible = "qcom,pcie-ipq9574";
+			reg =  <0x28000000 0xf1d>,
+			       <0x28000F20 0xa8>,
+			       <0x28001000 0x1000>,
+			       <0x00080000 0x4000>,
+			       <0x28100000 0x1000>;
+			reg-names = "dbi", "elbi", "atu", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x28200000 0x0 0x100000>,  /* I/O */
+				 <0x02000000 0x0 0x28300000 0x28300000 0x0 0x7d00000>; /* MEM */
+
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 75 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 78 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 79 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 83 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			/* clocks and clock-names are used to enable the clock in CBCR */
+			clocks = <&gcc GCC_PCIE0_AHB_CLK>,
+				 <&gcc GCC_PCIE0_AUX_CLK>,
+				 <&gcc GCC_PCIE0_AXI_M_CLK>,
+				 <&gcc GCC_PCIE0_AXI_S_CLK>,
+				 <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
+				 <&gcc GCC_PCIE0_RCHNG_CLK>;
+			clock-names = "ahb",
+				      "aux",
+				      "axi_m",
+				      "axi_s",
+				      "axi_bridge",
+				      "rchng";
+
+			resets = <&gcc GCC_PCIE0_PIPE_ARES>,
+				 <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_S_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_S_ARES>,
+				 <&gcc GCC_PCIE0_AXI_M_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_M_ARES>,
+				 <&gcc GCC_PCIE0_AUX_ARES>,
+				 <&gcc GCC_PCIE0_AHB_ARES>;
+			reset-names = "pipe",
+				      "sticky",
+				      "axi_s_sticky",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "axi_m",
+				      "aux",
+				      "ahb";
+
+			phys = <&pcie0_phy>;
+			phy-names = "pciephy";
+			interconnects = <&gcc MASTER_ANOC_PCIE0 &gcc SLAVE_ANOC_PCIE0>,
+					<&gcc MASTER_SNOC_PCIE0 &gcc SLAVE_SNOC_PCIE0>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+			status = "disabled";
+		};
+
 	};
 
 	thermal-zones {
-- 
2.34.1

[PATCH V5 5/6] arm64: dts: qcom: ipq9574: Enable PCIe PHYs and controllers

[devi priya]

Enable the PCIe controller and PHY nodes corresponding to RDP 433.

Signed-off-by: devi priya <quic_devipriy@quicinc.com>
---
 Changes in V5:
	- No change

 arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 113 ++++++++++++++++++++
 1 file changed, 113 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
index 1bb8d96c9a82..f4b6d540612c 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
@@ -8,6 +8,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
 #include "ipq9574-rdp-common.dtsi"
 
 / {
@@ -15,6 +16,45 @@ / {
 	compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574";
 };
 
+&pcie1_phy {
+	status = "okay";
+};
+
+&pcie1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_default>;
+
+	perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pcie2_phy {
+	status = "okay";
+};
+
+&pcie2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie2_default>;
+
+	perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pcie3_phy {
+	status = "okay";
+};
+
+&pcie3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie3_default>;
+
+	perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
 &sdhc_1 {
 	pinctrl-0 = <&sdc_default_state>;
 	pinctrl-names = "default";
@@ -28,6 +68,79 @@ &sdhc_1 {
 };
 
 &tlmm {
+
+	pcie1_default: pcie1-default-state {
+		clkreq-n-pins {
+			pins = "gpio25";
+			function = "pcie1_clk";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio26";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+			output-low;
+		};
+
+		wake-n-pins {
+			pins = "gpio27";
+			function = "pcie1_wake";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	pcie2_default: pcie2-default-state {
+		clkreq-n-pins {
+			pins = "gpio28";
+			function = "pcie2_clk";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio29";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+			output-low;
+		};
+
+		wake-n-pins {
+			pins = "gpio30";
+			function = "pcie2_wake";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	pcie3_default: pcie3-default-state {
+		clkreq-n-pins {
+			pins = "gpio31";
+			function = "pcie3_clk";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio32";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+			output-low;
+		};
+
+		wake-n-pins {
+			pins = "gpio33";
+			function = "pcie3_wake";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
 	sdc_default_state: sdc-default-state {
 		clk-pins {
 			pins = "gpio5";
-- 
2.34.1

[PATCH V5 6/6] PCI: qcom: Add support for IPQ9574

[devi priya]

The IPQ9574 platform has 4 Gen3 PCIe controllers:
two single-lane and two dual-lane based on SNPS core 5.70a

The Qcom IP rev is 1.27.0 and Synopsys IP rev is 5.80a
Added a new compatible 'qcom,pcie-ipq9574' and 'ops_1_27_0'
which reuses all the members of 'ops_2_9_0' except for the post_init
as the SLV_ADDR_SPACE_SIZE configuration differs between 2_9_0
and 1_27_0.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
---
 Changes in V5:
	- Rebased on top of the below series which adds support for fetching
	  clocks from the device tree
	  https://lore.kernel.org/linux-pci/20240417-pci-qcom-clk-bulk-v1-1-52ca19b3d6b2@linaro.org/

 drivers/pci/controller/dwc/pcie-qcom.c | 36 +++++++++++++++++++++++---
 1 file changed, 32 insertions(+), 4 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 3d2eeff9a876..af36a29c092e 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -106,6 +106,7 @@
 
 /* PARF_SLV_ADDR_SPACE_SIZE register value */
 #define SLV_ADDR_SPACE_SZ			0x10000000
+#define SLV_ADDR_SPACE_SZ_1_27_0		0x08000000
 
 /* PARF_MHI_CLOCK_RESET_CTRL register fields */
 #define AHB_CLK_EN				BIT(0)
@@ -1095,16 +1096,13 @@ static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
 	return clk_bulk_prepare_enable(res->num_clks, res->clks);
 }
 
-static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
+static int qcom_pcie_post_init(struct qcom_pcie *pcie)
 {
 	struct dw_pcie *pci = pcie->pci;
 	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
 	u32 val;
 	int i;
 
-	writel(SLV_ADDR_SPACE_SZ,
-		pcie->parf + PARF_SLV_ADDR_SPACE_SIZE);
-
 	val = readl(pcie->parf + PARF_PHY_CTRL);
 	val &= ~PHY_TEST_PWR_DOWN;
 	writel(val, pcie->parf + PARF_PHY_CTRL);
@@ -1144,6 +1142,22 @@ static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
 	return 0;
 }
 
+static int qcom_pcie_post_init_1_27_0(struct qcom_pcie *pcie)
+{
+	writel(SLV_ADDR_SPACE_SZ_1_27_0,
+	       pcie->parf + PARF_SLV_ADDR_SPACE_SIZE);
+
+	return qcom_pcie_post_init(pcie);
+}
+
+static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
+{
+	writel(SLV_ADDR_SPACE_SZ,
+	       pcie->parf + PARF_SLV_ADDR_SPACE_SIZE);
+
+	return qcom_pcie_post_init(pcie);
+}
+
 static int qcom_pcie_link_up(struct dw_pcie *pci)
 {
 	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
@@ -1297,6 +1311,15 @@ static const struct qcom_pcie_ops ops_2_9_0 = {
 	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
 };
 
+/* Qcom IP rev.: 1.27.0  Synopsys IP rev.: 5.80a */
+static const struct qcom_pcie_ops ops_1_27_0 = {
+	.get_resources = qcom_pcie_get_resources_2_9_0,
+	.init = qcom_pcie_init_2_9_0,
+	.post_init = qcom_pcie_post_init_1_27_0,
+	.deinit = qcom_pcie_deinit_2_9_0,
+	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
+};
+
 static const struct qcom_pcie_cfg cfg_1_0_0 = {
 	.ops = &ops_1_0_0,
 };
@@ -1334,6 +1357,10 @@ static const struct qcom_pcie_cfg cfg_sc8280xp = {
 	.no_l0s = true,
 };
 
+static const struct qcom_pcie_cfg cfg_1_27_0 = {
+	.ops = &ops_1_27_0,
+};
+
 static const struct dw_pcie_ops dw_pcie_ops = {
 	.link_up = qcom_pcie_link_up,
 	.start_link = qcom_pcie_start_link,
@@ -1603,6 +1630,7 @@ static const struct of_device_id qcom_pcie_match[] = {
 	{ .compatible = "qcom,pcie-ipq8064-v2", .data = &cfg_2_1_0 },
 	{ .compatible = "qcom,pcie-ipq8074", .data = &cfg_2_3_3 },
 	{ .compatible = "qcom,pcie-ipq8074-gen3", .data = &cfg_2_9_0 },
+	{ .compatible = "qcom,pcie-ipq9574", .data = &cfg_1_27_0 },
 	{ .compatible = "qcom,pcie-msm8996", .data = &cfg_2_3_2 },
 	{ .compatible = "qcom,pcie-qcs404", .data = &cfg_2_4_0 },
 	{ .compatible = "qcom,pcie-sa8540p", .data = &cfg_sc8280xp },
-- 
2.34.1

Re: [PATCH V5 3/6] dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller.

[Krzysztof Kozlowski]

On 12/05/2024 10:28, devi priya wrote:

>  
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - qcom,pcie-ipq9574
> +    then:
> +      properties:
> +        clocks:
> +          minItems: 6
> +          maxItems: 6
> +        clock-names:
> +          items:
> +            - const: ahb  # AHB clock
> +            - const: aux  # Auxiliary clock
> +            - const: axi_m # AXI Master clock
> +            - const: axi_s # AXI Slave clock
> +            - const: axi_bridge # AXI bridge clock
> +            - const: rchng

That's introducing one more order of clocks... Please keep it
consistent. The only existing case with ahb has it at after axi_m and
others. Why making things everytime differently?

I also to propose to finally drop the obvious comments, like "AHB
clock". It cannot be anything else. AXI Master / slave are descriptive,
so should stay.

Best regards,
Krzysztof

Re: [PATCH V5 3/6] dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller.

[Manivannan Sadhasivam]

On Mon, May 13, 2024 at 08:48:19AM +0200, Krzysztof Kozlowski wrote:
> On 12/05/2024 10:28, devi priya wrote:
> 
> >  
> > +  - if:
> > +      properties:
> > +        compatible:
> > +          contains:
> > +            enum:
> > +              - qcom,pcie-ipq9574
> > +    then:
> > +      properties:
> > +        clocks:
> > +          minItems: 6
> > +          maxItems: 6
> > +        clock-names:
> > +          items:
> > +            - const: ahb  # AHB clock
> > +            - const: aux  # Auxiliary clock
> > +            - const: axi_m # AXI Master clock
> > +            - const: axi_s # AXI Slave clock
> > +            - const: axi_bridge # AXI bridge clock
> > +            - const: rchng
> 
> That's introducing one more order of clocks... Please keep it
> consistent. The only existing case with ahb has it at after axi_m and
> others. Why making things everytime differently?
> 
> I also to propose to finally drop the obvious comments, like "AHB
> clock". It cannot be anything else. AXI Master / slave are descriptive,
> so should stay.
> 

+1 to drop the names.

- Mani

-- 
மணிவண்ணன் சதாசிவம்

Re: [PATCH V5 4/6] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes

[Manivannan Sadhasivam]

On Sun, May 12, 2024 at 01:58:56PM +0530, devi priya wrote:
> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
> 
> Signed-off-by: devi priya <quic_devipriy@quicinc.com>
> ---
>  Changes in V5:
> 	- Dropped anoc and snoc lane clocks from Phy nodes and enabled them
> 	  via interconnect.
> 	- Dropped msi-parent as it is handled via msi IRQ
> 
>  arch/arm64/boot/dts/qcom/ipq9574.dtsi | 365 +++++++++++++++++++++++++-
>  1 file changed, 361 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> index 5b3e69379b1f..da6418c9d52b 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi

[...]

> +		pcie1: pci@10000000 {

'pcie@' since this is a PCIe controller.

> +			compatible = "qcom,pcie-ipq9574";
> +			reg =  <0x10000000 0xf1d>,
> +			       <0x10000F20 0xa8>,

Please use lower case for hex everywhere.

> +			       <0x10001000 0x1000>,
> +			       <0x000F8000 0x4000>,
> +			       <0x10100000 0x1000>;
> +			reg-names = "dbi", "elbi", "atu", "parf", "config";
> +			device_type = "pci";
> +			linux,pci-domain = <2>;
> +			bus-range = <0x00 0xff>;
> +			num-lanes = <1>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			ranges = <0x01000000 0x0 0x00000000 0x10200000 0x0 0x100000>,  /* I/O */
> +				 <0x02000000 0x0 0x10300000 0x10300000 0x0 0x7d00000>; /* MEM */
> +
> +			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi";

Are you sure that this platform only has single MSI SPI IRQ?

> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc 0 0 35 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> +					<0 0 0 2 &intc 0 0 49 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +					<0 0 0 3 &intc 0 0 84 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +					<0 0 0 4 &intc 0 0 85 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
> +			/* clocks and clock-names are used to enable the clock in CBCR */

This comment is redundant.

> +			clocks = <&gcc GCC_PCIE1_AHB_CLK>,
> +				 <&gcc GCC_PCIE1_AUX_CLK>,
> +				 <&gcc GCC_PCIE1_AXI_M_CLK>,
> +				 <&gcc GCC_PCIE1_AXI_S_CLK>,
> +				 <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
> +				 <&gcc GCC_PCIE1_RCHNG_CLK>;
> +			clock-names = "ahb",
> +				      "aux",
> +				      "axi_m",
> +				      "axi_s",
> +				      "axi_bridge",
> +				      "rchng";
> +
> +			resets = <&gcc GCC_PCIE1_PIPE_ARES>,
> +				 <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
> +				 <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
> +				 <&gcc GCC_PCIE1_AXI_S_ARES>,
> +				 <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
> +				 <&gcc GCC_PCIE1_AXI_M_ARES>,
> +				 <&gcc GCC_PCIE1_AUX_ARES>,
> +				 <&gcc GCC_PCIE1_AHB_ARES>;
> +			reset-names = "pipe",
> +				      "sticky",
> +				      "axi_s_sticky",
> +				      "axi_s",
> +				      "axi_m_sticky",
> +				      "axi_m",
> +				      "aux",
> +				      "ahb";
> +
> +			phys = <&pcie1_phy>;
> +			phy-names = "pciephy";
> +			interconnects = <&gcc MASTER_ANOC_PCIE1 &gcc SLAVE_ANOC_PCIE1>,
> +					<&gcc MASTER_SNOC_PCIE1 &gcc SLAVE_SNOC_PCIE1>;

Is this really the interconnect paths between PCIe-DDR and PCIe-CPU? I doubt...

- Mani

-- 
மணிவண்ணன் சதாசிவம்

Re: [PATCH V5 3/6] dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller.

[Devi Priya]

On 5/13/2024 12:18 PM, Krzysztof Kozlowski wrote:
> On 12/05/2024 10:28, devi priya wrote:
> 
>>   
>> +  - if:
>> +      properties:
>> +        compatible:
>> +          contains:
>> +            enum:
>> +              - qcom,pcie-ipq9574
>> +    then:
>> +      properties:
>> +        clocks:
>> +          minItems: 6
>> +          maxItems: 6
>> +        clock-names:
>> +          items:
>> +            - const: ahb  # AHB clock
>> +            - const: aux  # Auxiliary clock
>> +            - const: axi_m # AXI Master clock
>> +            - const: axi_s # AXI Slave clock
>> +            - const: axi_bridge # AXI bridge clock
>> +            - const: rchng
> 
> That's introducing one more order of clocks... Please keep it
> consistent. The only existing case with ahb has it at after axi_m and
> others. Why making things everytime differently?
> 
> I also to propose to finally drop the obvious comments, like "AHB
> clock". It cannot be anything else. AXI Master / slave are descriptive,
> so should stay.
Sure okay, will update this in next spin.

Thanks,
Devi Priya
> 
> Best regards,
> Krzysztof
> 

Re: [PATCH V5 4/6] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes

[Devi Priya]

On 5/14/2024 1:09 PM, Manivannan Sadhasivam wrote:
> On Sun, May 12, 2024 at 01:58:56PM +0530, devi priya wrote:
>> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
>> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
>> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>>
>> Signed-off-by: devi priya <quic_devipriy@quicinc.com>
>> ---
>>   Changes in V5:
>> 	- Dropped anoc and snoc lane clocks from Phy nodes and enabled them
>> 	  via interconnect.
>> 	- Dropped msi-parent as it is handled via msi IRQ
>>
>>   arch/arm64/boot/dts/qcom/ipq9574.dtsi | 365 +++++++++++++++++++++++++-
>>   1 file changed, 361 insertions(+), 4 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> index 5b3e69379b1f..da6418c9d52b 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> 
> [...]
> 
>> +		pcie1: pci@10000000 {
> 
> 'pcie@' since this is a PCIe controller.
okay
> 
>> +			compatible = "qcom,pcie-ipq9574";
>> +			reg =  <0x10000000 0xf1d>,
>> +			       <0x10000F20 0xa8>,
> 
> Please use lower case for hex everywhere.
okay
> 
>> +			       <0x10001000 0x1000>,
>> +			       <0x000F8000 0x4000>,
>> +			       <0x10100000 0x1000>;
>> +			reg-names = "dbi", "elbi", "atu", "parf", "config";
>> +			device_type = "pci";
>> +			linux,pci-domain = <2>;
>> +			bus-range = <0x00 0xff>;
>> +			num-lanes = <1>;
>> +			#address-cells = <3>;
>> +			#size-cells = <2>;
>> +
>> +			ranges = <0x01000000 0x0 0x00000000 0x10200000 0x0 0x100000>,  /* I/O */
>> +				 <0x02000000 0x0 0x10300000 0x10300000 0x0 0x7d00000>; /* MEM */
>> +
>> +			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "msi";
> 
> Are you sure that this platform only has single MSI SPI IRQ?
It has 8 MSI SPI IRQs, will define all of them
> 
>> +			#interrupt-cells = <1>;
>> +			interrupt-map-mask = <0 0 0 0x7>;
>> +			interrupt-map = <0 0 0 1 &intc 0 0 35 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
>> +					<0 0 0 2 &intc 0 0 49 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
>> +					<0 0 0 3 &intc 0 0 84 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
>> +					<0 0 0 4 &intc 0 0 85 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
>> +
>> +			/* clocks and clock-names are used to enable the clock in CBCR */
> 
> This comment is redundant.
okay
> 
>> +			clocks = <&gcc GCC_PCIE1_AHB_CLK>,
>> +				 <&gcc GCC_PCIE1_AUX_CLK>,
>> +				 <&gcc GCC_PCIE1_AXI_M_CLK>,
>> +				 <&gcc GCC_PCIE1_AXI_S_CLK>,
>> +				 <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
>> +				 <&gcc GCC_PCIE1_RCHNG_CLK>;
>> +			clock-names = "ahb",
>> +				      "aux",
>> +				      "axi_m",
>> +				      "axi_s",
>> +				      "axi_bridge",
>> +				      "rchng";
>> +
>> +			resets = <&gcc GCC_PCIE1_PIPE_ARES>,
>> +				 <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
>> +				 <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
>> +				 <&gcc GCC_PCIE1_AXI_S_ARES>,
>> +				 <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
>> +				 <&gcc GCC_PCIE1_AXI_M_ARES>,
>> +				 <&gcc GCC_PCIE1_AUX_ARES>,
>> +				 <&gcc GCC_PCIE1_AHB_ARES>;
>> +			reset-names = "pipe",
>> +				      "sticky",
>> +				      "axi_s_sticky",
>> +				      "axi_s",
>> +				      "axi_m_sticky",
>> +				      "axi_m",
>> +				      "aux",
>> +				      "ahb";
>> +
>> +			phys = <&pcie1_phy>;
>> +			phy-names = "pciephy";
>> +			interconnects = <&gcc MASTER_ANOC_PCIE1 &gcc SLAVE_ANOC_PCIE1>,
>> +					<&gcc MASTER_SNOC_PCIE1 &gcc SLAVE_SNOC_PCIE1>;
> 
> Is this really the interconnect paths between PCIe-DDR and PCIe-CPU? I doubt...

We actually designed a minimalistic ICC driver for enabling the NoC 
clocks based on the suggestions received from the community.
Please find the link to the discussions that went in for introducing the 
ICC driver for NoC clock enablement

https://lore.kernel.org/linux-arm-msm/abd29b47-a8ab-4e2a-8147-d5d8ded98065@linaro.org/

Thanks,
Devi Priya
> 
> - Mani
> 

Re: [PATCH V5 1/6] Add PCIe pipe clock definitions for IPQ9574 SoC.

[Bjorn Helgaas]

On Sun, May 12, 2024 at 01:58:53PM +0530, devi priya wrote:

Please run "git log --oneline include/dt-bindings/clock/qcom,ipq9574-gcc.h"
and follow the subject line style there:

  - prefix "dt-bindings: clock: "
  - no trailing period
  - perhaps add commit log text if there's anything else useful to put
    there

> Acked-by: Stephen Boyd <sboyd@kernel.org>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: devi priya <quic_devipriy@quicinc.com>
> ---
>  Changes in V5:
> 	- No changes
> 
>  include/dt-bindings/clock/qcom,ipq9574-gcc.h | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/include/dt-bindings/clock/qcom,ipq9574-gcc.h b/include/dt-bindings/clock/qcom,ipq9574-gcc.h
> index 08fd3a37acaa..52123c5a09fa 100644
> --- a/include/dt-bindings/clock/qcom,ipq9574-gcc.h
> +++ b/include/dt-bindings/clock/qcom,ipq9574-gcc.h
> @@ -216,4 +216,8 @@
>  #define GCC_CRYPTO_AHB_CLK				207
>  #define GCC_USB0_PIPE_CLK				208
>  #define GCC_USB0_SLEEP_CLK				209
> +#define GCC_PCIE0_PIPE_CLK				210
> +#define GCC_PCIE1_PIPE_CLK				211
> +#define GCC_PCIE2_PIPE_CLK				212
> +#define GCC_PCIE3_PIPE_CLK				213
>  #endif
> -- 
> 2.34.1
>