* [PATCH] PCI: qcom: Enable clocks only after PARF_PHY setup for rev 2.1.0
@ 2022-07-08 22:27 Christian Marangi
2022-07-08 23:01 ` Bjorn Helgaas
0 siblings, 1 reply; 5+ messages in thread
From: Christian Marangi @ 2022-07-08 22:27 UTC (permalink / raw)
To: Stanimir Varbanov, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Lorenzo Pieralisi, Rob Herring, Krzysztof Wilczyński,
Bjorn Helgaas, linux-pci, linux-arm-msm, linux-kernel
Cc: Christian Marangi, stable
We currently enable clocks BEFORE we write to PARF_PHY_CTRL reg to
enable clocks and resets. This case the driver to never set to a ready
state with the error 'Phy link never came up'.
This in fact is caused by the phy clock getting enabled before setting
the required bits in the PARF regs.
A workaround for this was set but with this new discovery we can drop
the workaround and use a proper solution to the problem by just enabling
the clock only AFTER the PARF_PHY_CTRL bit is set.
This correctly setup the pcie line and makes it usable even when a
bootloader leave the pcie line to a underfined state.
Fixes: 82a823833f4e ("PCI: qcom: Add Qualcomm PCIe controller driver")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
drivers/pci/controller/dwc/pcie-qcom.c | 10 ++++------
1 file changed, 4 insertions(+), 6 deletions(-)
diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 2ea13750b492..da13a66ced14 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -337,8 +337,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
reset_control_assert(res->ext_reset);
reset_control_assert(res->phy_reset);
- writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL);
-
ret = regulator_bulk_enable(ARRAY_SIZE(res->supplies), res->supplies);
if (ret < 0) {
dev_err(dev, "cannot enable regulators\n");
@@ -381,15 +379,15 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
goto err_deassert_axi;
}
- ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
- if (ret)
- goto err_clks;
-
/* enable PCIe clocks and resets */
val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
val &= ~BIT(0);
writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
+ ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
+ if (ret)
+ goto err_clks;
+
if (of_device_is_compatible(node, "qcom,pcie-ipq8064") ||
of_device_is_compatible(node, "qcom,pcie-ipq8064-v2")) {
writel(PCS_DEEMPH_TX_DEEMPH_GEN1(24) |
--
2.36.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH] PCI: qcom: Enable clocks only after PARF_PHY setup for rev 2.1.0
2022-07-08 22:27 [PATCH] PCI: qcom: Enable clocks only after PARF_PHY setup for rev 2.1.0 Christian Marangi
@ 2022-07-08 23:01 ` Bjorn Helgaas
2022-07-09 1:03 ` Christian Marangi
0 siblings, 1 reply; 5+ messages in thread
From: Bjorn Helgaas @ 2022-07-08 23:01 UTC (permalink / raw)
To: Christian Marangi
Cc: Stanimir Varbanov, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Lorenzo Pieralisi, Rob Herring, Krzysztof Wilczyński,
Bjorn Helgaas, linux-pci, linux-arm-msm, linux-kernel, stable
On Sat, Jul 09, 2022 at 12:27:43AM +0200, Christian Marangi wrote:
> We currently enable clocks BEFORE we write to PARF_PHY_CTRL reg to
> enable clocks and resets. This case the driver to never set to a ready
> state with the error 'Phy link never came up'.
>
> This in fact is caused by the phy clock getting enabled before setting
> the required bits in the PARF regs.
>
> A workaround for this was set but with this new discovery we can drop
> the workaround and use a proper solution to the problem by just enabling
> the clock only AFTER the PARF_PHY_CTRL bit is set.
>
> This correctly setup the pcie line and makes it usable even when a
> bootloader leave the pcie line to a underfined state.
Is "pcie" here a signal name? Maybe this refers to the "PCIe link"?
> Fixes: 82a823833f4e ("PCI: qcom: Add Qualcomm PCIe controller driver")
> Cc: stable@vger.kernel.org # v5.4+
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Thanks, I put this on
https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git,
pci/ctrl/qcom-pending branch (head 47b4ec9d2e60).
Can you take a look and make sure I didn't mess up the conflict
resolution with the rest of the series?
> ---
> drivers/pci/controller/dwc/pcie-qcom.c | 10 ++++------
> 1 file changed, 4 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index 2ea13750b492..da13a66ced14 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -337,8 +337,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
> reset_control_assert(res->ext_reset);
> reset_control_assert(res->phy_reset);
>
> - writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL);
> -
> ret = regulator_bulk_enable(ARRAY_SIZE(res->supplies), res->supplies);
> if (ret < 0) {
> dev_err(dev, "cannot enable regulators\n");
> @@ -381,15 +379,15 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
> goto err_deassert_axi;
> }
>
> - ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> - if (ret)
> - goto err_clks;
> -
> /* enable PCIe clocks and resets */
> val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
> val &= ~BIT(0);
> writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
>
> + ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> + if (ret)
> + goto err_clks;
> +
> if (of_device_is_compatible(node, "qcom,pcie-ipq8064") ||
> of_device_is_compatible(node, "qcom,pcie-ipq8064-v2")) {
> writel(PCS_DEEMPH_TX_DEEMPH_GEN1(24) |
> --
> 2.36.1
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH] PCI: qcom: Enable clocks only after PARF_PHY setup for rev 2.1.0
2022-07-08 23:01 ` Bjorn Helgaas
@ 2022-07-09 1:03 ` Christian Marangi
2022-07-11 19:22 ` Bjorn Helgaas
0 siblings, 1 reply; 5+ messages in thread
From: Christian Marangi @ 2022-07-09 1:03 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: Stanimir Varbanov, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Lorenzo Pieralisi, Rob Herring, Krzysztof Wilczyński,
Bjorn Helgaas, linux-pci, linux-arm-msm, linux-kernel, stable
On Fri, Jul 08, 2022 at 06:01:55PM -0500, Bjorn Helgaas wrote:
> On Sat, Jul 09, 2022 at 12:27:43AM +0200, Christian Marangi wrote:
> > We currently enable clocks BEFORE we write to PARF_PHY_CTRL reg to
> > enable clocks and resets. This case the driver to never set to a ready
> > state with the error 'Phy link never came up'.
> >
> > This in fact is caused by the phy clock getting enabled before setting
> > the required bits in the PARF regs.
> >
> > A workaround for this was set but with this new discovery we can drop
> > the workaround and use a proper solution to the problem by just enabling
> > the clock only AFTER the PARF_PHY_CTRL bit is set.
> >
> > This correctly setup the pcie line and makes it usable even when a
> > bootloader leave the pcie line to a underfined state.
>
> Is "pcie" here a signal name? Maybe this refers to the "PCIe link"?
>
Hi,
no i was referring to PCIe link. Fell free to fix it if it's not a
problem (or if you want i can just resend)
> > Fixes: 82a823833f4e ("PCI: qcom: Add Qualcomm PCIe controller driver")
> > Cc: stable@vger.kernel.org # v5.4+
> > Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
>
> Thanks, I put this on
> https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git,
> pci/ctrl/qcom-pending branch (head 47b4ec9d2e60).
>
> Can you take a look and make sure I didn't mess up the conflict
> resolution with the rest of the series?
Think something went wrong in the rebase as the patch fixup is reverted.
11946f8b6e77a6794c111aafef7772e9967d9a54 is still wrong.
clk_bulk_prepare_enable must be after
writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
so in the post init.
>
> > ---
> > drivers/pci/controller/dwc/pcie-qcom.c | 10 ++++------
> > 1 file changed, 4 insertions(+), 6 deletions(-)
> >
> > diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> > index 2ea13750b492..da13a66ced14 100644
> > --- a/drivers/pci/controller/dwc/pcie-qcom.c
> > +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> > @@ -337,8 +337,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
> > reset_control_assert(res->ext_reset);
> > reset_control_assert(res->phy_reset);
> >
> > - writel(1, pcie->parf + PCIE20_PARF_PHY_CTRL);
> > -
> > ret = regulator_bulk_enable(ARRAY_SIZE(res->supplies), res->supplies);
> > if (ret < 0) {
> > dev_err(dev, "cannot enable regulators\n");
> > @@ -381,15 +379,15 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
> > goto err_deassert_axi;
> > }
> >
> > - ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> > - if (ret)
> > - goto err_clks;
> > -
> > /* enable PCIe clocks and resets */
> > val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
> > val &= ~BIT(0);
> > writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
> >
> > + ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> > + if (ret)
> > + goto err_clks;
> > +
> > if (of_device_is_compatible(node, "qcom,pcie-ipq8064") ||
> > of_device_is_compatible(node, "qcom,pcie-ipq8064-v2")) {
> > writel(PCS_DEEMPH_TX_DEEMPH_GEN1(24) |
> > --
> > 2.36.1
> >
--
Ansuel
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH] PCI: qcom: Enable clocks only after PARF_PHY setup for rev 2.1.0
2022-07-09 1:03 ` Christian Marangi
@ 2022-07-11 19:22 ` Bjorn Helgaas
2022-07-11 21:13 ` Robert Marko
0 siblings, 1 reply; 5+ messages in thread
From: Bjorn Helgaas @ 2022-07-11 19:22 UTC (permalink / raw)
To: Christian Marangi
Cc: Stanimir Varbanov, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Lorenzo Pieralisi, Rob Herring, Krzysztof Wilczyński,
Bjorn Helgaas, linux-pci, linux-arm-msm, linux-kernel,
Robert Marko
[+cc Robert since I resolved a conflict in his patch, -cc stable]
On Sat, Jul 09, 2022 at 03:03:34AM +0200, Christian Marangi wrote:
> On Fri, Jul 08, 2022 at 06:01:55PM -0500, Bjorn Helgaas wrote:
> > On Sat, Jul 09, 2022 at 12:27:43AM +0200, Christian Marangi wrote:
> > > We currently enable clocks BEFORE we write to PARF_PHY_CTRL reg to
> > > enable clocks and resets. This case the driver to never set to a ready
> > > state with the error 'Phy link never came up'.
> > >
> > > This in fact is caused by the phy clock getting enabled before setting
> > > the required bits in the PARF regs.
> > >
> > > A workaround for this was set but with this new discovery we can drop
> > > the workaround and use a proper solution to the problem by just enabling
> > > the clock only AFTER the PARF_PHY_CTRL bit is set.
> > >
> > > This correctly setup the pcie line and makes it usable even when a
> > > bootloader leave the pcie line to a underfined state.
> >
> > Is "pcie" here a signal name? Maybe this refers to the "PCIe link"?
>
> no i was referring to PCIe link. Fell free to fix it if it's not a
> problem (or if you want i can just resend)
I fixed it.
> Think something went wrong in the rebase as the patch fixup is reverted.
>
> 11946f8b6e77a6794c111aafef7772e9967d9a54 is still wrong.
>
> clk_bulk_prepare_enable must be after
> writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
> so in the post init.
My error, sorry. I updated it, current head:
1a88605a3efd ("dt-bindings: PCI: qcom: Fix description typo")
Robert, your patch that I updated is:
https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git/commit/?h=pci/ctrl/qcom-pending&id=cdb32283bcf202d0db512abb80794056d44e7e9f
It would still be nice to get an ack from one of the maintainers for
this.
Bjorn
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH] PCI: qcom: Enable clocks only after PARF_PHY setup for rev 2.1.0
2022-07-11 19:22 ` Bjorn Helgaas
@ 2022-07-11 21:13 ` Robert Marko
0 siblings, 0 replies; 5+ messages in thread
From: Robert Marko @ 2022-07-11 21:13 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: Christian Marangi, Stanimir Varbanov, Andy Gross,
Bjorn Andersson, Konrad Dybcio, Lorenzo Pieralisi, Rob Herring,
Krzysztof Wilczyński, Bjorn Helgaas, linux-pci,
linux-arm-msm, open list
On Mon, 11 Jul 2022 at 21:22, Bjorn Helgaas <helgaas@kernel.org> wrote:
>
> [+cc Robert since I resolved a conflict in his patch, -cc stable]
>
> On Sat, Jul 09, 2022 at 03:03:34AM +0200, Christian Marangi wrote:
> > On Fri, Jul 08, 2022 at 06:01:55PM -0500, Bjorn Helgaas wrote:
> > > On Sat, Jul 09, 2022 at 12:27:43AM +0200, Christian Marangi wrote:
> > > > We currently enable clocks BEFORE we write to PARF_PHY_CTRL reg to
> > > > enable clocks and resets. This case the driver to never set to a ready
> > > > state with the error 'Phy link never came up'.
> > > >
> > > > This in fact is caused by the phy clock getting enabled before setting
> > > > the required bits in the PARF regs.
> > > >
> > > > A workaround for this was set but with this new discovery we can drop
> > > > the workaround and use a proper solution to the problem by just enabling
> > > > the clock only AFTER the PARF_PHY_CTRL bit is set.
> > > >
> > > > This correctly setup the pcie line and makes it usable even when a
> > > > bootloader leave the pcie line to a underfined state.
> > >
> > > Is "pcie" here a signal name? Maybe this refers to the "PCIe link"?
> >
> > no i was referring to PCIe link. Fell free to fix it if it's not a
> > problem (or if you want i can just resend)
>
> I fixed it.
>
> > Think something went wrong in the rebase as the patch fixup is reverted.
> >
> > 11946f8b6e77a6794c111aafef7772e9967d9a54 is still wrong.
> >
> > clk_bulk_prepare_enable must be after
> > writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
> > so in the post init.
>
> My error, sorry. I updated it, current head:
>
> 1a88605a3efd ("dt-bindings: PCI: qcom: Fix description typo")
>
> Robert, your patch that I updated is:
>
> https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git/commit/?h=pci/ctrl/qcom-pending&id=cdb32283bcf202d0db512abb80794056d44e7e9f
>
> It would still be nice to get an ack from one of the maintainers for
> this.
Hi,
Thanks, everybody for working on sorting this out.
I understand, hopefully, somebody can take a look at it.
BTW, happy to see IPQ60xx support made it in as IPQ807x
can use it for Gen3.
Regards,
Robert
>
> Bjorn
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2022-07-11 21:13 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-07-08 22:27 [PATCH] PCI: qcom: Enable clocks only after PARF_PHY setup for rev 2.1.0 Christian Marangi
2022-07-08 23:01 ` Bjorn Helgaas
2022-07-09 1:03 ` Christian Marangi
2022-07-11 19:22 ` Bjorn Helgaas
2022-07-11 21:13 ` Robert Marko
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).