[PATCH 0/7] Use mboxes instead of syscon for APCS (arm32 & arm64)

[PATCH 0/7] Use mboxes instead of syscon for APCS (arm32 & arm64)

[Luca Weiss]

The first patch is for removing a bogus error warning I've noticed while
developing this on msm8226 - there the patches are also coming later for
this SoC since apcs is getting hooked up to cpufreq there also.

Apart from usages from the qcom,smsm driver (patches coming!) all other
usages of the apcs mailbox now go via the mailbox driver - where one is
used, so some arm32 boards will continue using "qcom,ipc*" properties in
the short or long term.

Only compile-tested apart from msm8953 (tested on sdm632-fairphone-fp3)
and msm8974 (tested on msm8974pro-fairphone-fp2), but I don't expect any
complications with this.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
Luca Weiss (7):
      rpmsg: qcom_smd: Don't print error during probe deferral
      ARM: dts: qcom: msm8974: Use mboxes properties for APCS
      arm64: dts: qcom: msm8916: Use mboxes properties for APCS
      arm64: dts: qcom: msm8939: Use mboxes properties for APCS
      arm64: dts: qcom: msm8953: Use mboxes properties for APCS
      arm64: dts: qcom: msm8976: Use mboxes properties for APCS
      arm64: dts: qcom: msm8994: Use mboxes properties for APCS

 arch/arm/boot/dts/qcom/qcom-msm8974.dtsi | 14 +++++++-------
 arch/arm64/boot/dts/qcom/msm8916.dtsi    | 10 +++++-----
 arch/arm64/boot/dts/qcom/msm8939.dtsi    |  4 ++--
 arch/arm64/boot/dts/qcom/msm8953.dtsi    | 10 +++++-----
 arch/arm64/boot/dts/qcom/msm8976.dtsi    |  8 ++++----
 arch/arm64/boot/dts/qcom/msm8994.dtsi    |  6 +++---
 drivers/rpmsg/qcom_smd.c                 |  3 ++-
 7 files changed, 28 insertions(+), 27 deletions(-)
---
base-commit: 43173e6dbaa227f3107310d4df4a3bacd5e0df33
change-id: 20240423-apcs-mboxes-12ee6c01a5b3

Best regards,
-- 
Luca Weiss <luca@z3ntu.xyz>

[PATCH 1/7] rpmsg: qcom_smd: Don't print error during probe deferral

[Luca Weiss]

When the mailbox driver has not probed yet, skip printing the error
message since it's just going to confuse users.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
 drivers/rpmsg/qcom_smd.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/rpmsg/qcom_smd.c b/drivers/rpmsg/qcom_smd.c
index 43f601c84b4f..6fc299657adf 100644
--- a/drivers/rpmsg/qcom_smd.c
+++ b/drivers/rpmsg/qcom_smd.c
@@ -1502,7 +1502,8 @@ struct qcom_smd_edge *qcom_smd_register_edge(struct device *parent,
 
 	ret = qcom_smd_parse_edge(&edge->dev, node, edge);
 	if (ret) {
-		dev_err(&edge->dev, "failed to parse smd edge\n");
+		if (ret != -EPROBE_DEFER)
+			dev_err(&edge->dev, "failed to parse smd edge\n");
 		goto unregister_dev;
 	}
 

-- 
2.44.0

[PATCH 2/7] ARM: dts: qcom: msm8974: Use mboxes properties for APCS

[Luca Weiss]

Instead of passing the syscon to the various nodes, use the mbox
interface using the mboxes property.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
 arch/arm/boot/dts/qcom/qcom-msm8974.dtsi | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
index 20958c47ff3a..0f1dc4355c7a 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
@@ -130,7 +130,7 @@ master-stats {
 
 		smd-edge {
 			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
-			qcom,ipc = <&apcs 8 0>;
+			mboxes = <&apcs 0>;
 			qcom,smd-edge = <15>;
 
 			rpm_requests: rpm-requests {
@@ -217,7 +217,7 @@ smp2p-adsp {
 		interrupt-parent = <&intc>;
 		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 10>;
+		mboxes = <&apcs 10>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <2>;
@@ -242,7 +242,7 @@ smp2p-modem {
 		interrupt-parent = <&intc>;
 		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 14>;
+		mboxes = <&apcs 14>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <1>;
@@ -267,7 +267,7 @@ smp2p-wcnss {
 		interrupt-parent = <&intc>;
 		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 18>;
+		mboxes = <&apcs 18>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <4>;
@@ -757,7 +757,7 @@ iris {
 			smd-edge {
 				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
 
-				qcom,ipc = <&apcs 8 17>;
+				mboxes = <&apcs 17>;
 				qcom,smd-edge = <6>;
 
 				wcnss {
@@ -1576,7 +1576,7 @@ bam_dmux: bam-dmux {
 			smd-edge {
 				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
 
-				qcom,ipc = <&apcs 8 12>;
+				mboxes = <&apcs 12>;
 				qcom,smd-edge = <0>;
 
 				label = "modem";
@@ -2213,7 +2213,7 @@ remoteproc_adsp: remoteproc@fe200000 {
 			smd-edge {
 				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
 
-				qcom,ipc = <&apcs 8 8>;
+				mboxes = <&apcs 8>;
 				qcom,smd-edge = <1>;
 				label = "lpass";
 			};

-- 
2.44.0

[PATCH 3/7] arm64: dts: qcom: msm8916: Use mboxes properties for APCS

[Luca Weiss]

Instead of passing the syscon to the various nodes, use the mbox
interface using the mboxes property.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
 arch/arm64/boot/dts/qcom/msm8916.dtsi | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index cedff4166bfb..46bb322ae133 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -308,7 +308,7 @@ rpm: remoteproc {
 
 		smd-edge {
 			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
-			qcom,ipc = <&apcs 8 0>;
+			mboxes = <&apcs 0>;
 			qcom,smd-edge = <15>;
 
 			rpm_requests: rpm-requests {
@@ -360,7 +360,7 @@ smp2p-hexagon {
 
 		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 14>;
+		mboxes = <&apcs 14>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <1>;
@@ -385,7 +385,7 @@ smp2p-wcnss {
 
 		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 18>;
+		mboxes = <&apcs 18>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <4>;
@@ -1978,7 +1978,7 @@ smd-edge {
 				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
 
 				qcom,smd-edge = <0>;
-				qcom,ipc = <&apcs 8 12>;
+				mboxes = <&apcs 12>;
 				qcom,remote-pid = <1>;
 
 				label = "hexagon";
@@ -2459,7 +2459,7 @@ wcnss_iris: iris {
 			smd-edge {
 				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
 
-				qcom,ipc = <&apcs 8 17>;
+				mboxes = <&apcs 17>;
 				qcom,smd-edge = <6>;
 				qcom,remote-pid = <4>;
 

-- 
2.44.0

[PATCH 4/7] arm64: dts: qcom: msm8939: Use mboxes properties for APCS

[Luca Weiss]

Instead of passing the syscon to the various nodes, use the mbox
interface using the mboxes property.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
 arch/arm64/boot/dts/qcom/msm8939.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
index dd45975682b2..95487de2ca6a 100644
--- a/arch/arm64/boot/dts/qcom/msm8939.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
@@ -248,7 +248,7 @@ rpm: remoteproc {
 
 		smd-edge {
 			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
-			qcom,ipc = <&apcs1_mbox 8 0>;
+			mboxes = <&apcs1_mbox 0>;
 			qcom,smd-edge = <15>;
 
 			rpm_requests: rpm-requests {
@@ -2067,7 +2067,7 @@ wcnss_iris: iris {
 
 			smd-edge {
 				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
-				qcom,ipc = <&apcs1_mbox 8 17>;
+				mboxes = <&apcs1_mbox 17>;
 				qcom,smd-edge = <6>;
 				qcom,remote-pid = <4>;
 

-- 
2.44.0

[PATCH 5/7] arm64: dts: qcom: msm8953: Use mboxes properties for APCS

[Luca Weiss]

Instead of passing the syscon to the various nodes, use the mbox
interface using the mboxes property.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
 arch/arm64/boot/dts/qcom/msm8953.dtsi | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
index f1011bb641c6..650ad75923f8 100644
--- a/arch/arm64/boot/dts/qcom/msm8953.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
@@ -195,7 +195,7 @@ rpm: remoteproc {
 
 		smd-edge {
 			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
-			qcom,ipc = <&apcs 8 0>;
+			mboxes = <&apcs 0>;
 			qcom,smd-edge = <15>;
 
 			rpm_requests: rpm-requests {
@@ -361,7 +361,7 @@ smp2p-modem {
 
 		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 14>;
+		mboxes = <&apcs 14>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <1>;
@@ -386,7 +386,7 @@ smp2p-wcnss {
 
 		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 18>;
+		mboxes = <&apcs 18>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <4>;
@@ -1267,7 +1267,7 @@ smd-edge {
 				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
 
 				qcom,smd-edge = <0>;
-				qcom,ipc = <&apcs 8 12>;
+				mboxes = <&apcs 12>;
 				qcom,remote-pid = <1>;
 
 				label = "modem";
@@ -1734,7 +1734,7 @@ wcnss_iris: iris {
 			smd-edge {
 				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
 
-				qcom,ipc = <&apcs 8 17>;
+				mboxes = <&apcs 17>;
 				qcom,smd-edge = <6>;
 				qcom,remote-pid = <4>;
 

-- 
2.44.0

[PATCH 6/7] arm64: dts: qcom: msm8976: Use mboxes properties for APCS

[Luca Weiss]

Instead of passing the syscon to the various nodes, use the mbox
interface using the mboxes property.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
 arch/arm64/boot/dts/qcom/msm8976.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8976.dtsi b/arch/arm64/boot/dts/qcom/msm8976.dtsi
index d2bb1ada361a..9ca0867e45ba 100644
--- a/arch/arm64/boot/dts/qcom/msm8976.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8976.dtsi
@@ -237,7 +237,7 @@ rpm: remoteproc {
 
 		smd-edge {
 			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
-			qcom,ipc = <&apcs 8 0>;
+			mboxes = <&apcs 0>;
 			qcom,smd-edge = <15>;
 
 			rpm_requests: rpm-requests {
@@ -361,7 +361,7 @@ tz-apps@8dd00000 {
 	smp2p-hexagon {
 		compatible = "qcom,smp2p";
 		interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>;
-		qcom,ipc = <&apcs 8 10>;
+		mboxes = <&apcs 10>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <2>;
@@ -384,7 +384,7 @@ adsp_smp2p_in: slave-kernel {
 	smp2p-modem {
 		compatible = "qcom,smp2p";
 		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
-		qcom,ipc = <&apcs 8 14>;
+		mboxes = <&apcs 14>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <1>;
@@ -407,7 +407,7 @@ modem_smp2p_in: slave-kernel {
 	smp2p-wcnss {
 		compatible = "qcom,smp2p";
 		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
-		qcom,ipc = <&apcs 8 18>;
+		mboxes = <&apcs 18>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <4>;

-- 
2.44.0

[PATCH 7/7] arm64: dts: qcom: msm8994: Use mboxes properties for APCS

[Luca Weiss]

Instead of passing the syscon to the various nodes, use the mbox
interface using the mboxes property.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
 arch/arm64/boot/dts/qcom/msm8994.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi
index 695e541832ad..9949d2cd23d8 100644
--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -183,7 +183,7 @@ rpm: remoteproc {
 
 		smd-edge {
 			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
-			qcom,ipc = <&apcs 8 0>;
+			mboxes = <&apcs 0>;
 			qcom,smd-edge = <15>;
 			qcom,remote-pid = <6>;
 
@@ -300,7 +300,7 @@ smp2p-lpass {
 
 		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 10>;
+		mboxes = <&apcs 10>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <2>;
@@ -325,7 +325,7 @@ smp2p-modem {
 		interrupt-parent = <&intc>;
 		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 14>;
+		mboxes = <&apcs 14>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <1>;

-- 
2.44.0

Re: [PATCH 0/7] Use mboxes instead of syscon for APCS (arm32 & arm64)

[Luca Weiss]

On Mittwoch, 24. April 2024 18:23:53 MESZ Luca Weiss wrote:
> The first patch is for removing a bogus error warning I've noticed while
> developing this on msm8226 - there the patches are also coming later for
> this SoC since apcs is getting hooked up to cpufreq there also.
> 
> Apart from usages from the qcom,smsm driver (patches coming!) all other
> usages of the apcs mailbox now go via the mailbox driver - where one is
> used, so some arm32 boards will continue using "qcom,ipc*" properties in
> the short or long term.
> 
> Only compile-tested apart from msm8953 (tested on sdm632-fairphone-fp3)
> and msm8974 (tested on msm8974pro-fairphone-fp2), but I don't expect any
> complications with this.

I think I forgot to mention this, but the msm8974 patch depends on
this series:
https://lore.kernel.org/linux-arm-msm/20240408-msm8974-apcs-v1-0-90cb7368836e@z3ntu.xyz/

> 
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> ---
> Luca Weiss (7):
>       rpmsg: qcom_smd: Don't print error during probe deferral
>       ARM: dts: qcom: msm8974: Use mboxes properties for APCS
>       arm64: dts: qcom: msm8916: Use mboxes properties for APCS
>       arm64: dts: qcom: msm8939: Use mboxes properties for APCS
>       arm64: dts: qcom: msm8953: Use mboxes properties for APCS
>       arm64: dts: qcom: msm8976: Use mboxes properties for APCS
>       arm64: dts: qcom: msm8994: Use mboxes properties for APCS
> 
>  arch/arm/boot/dts/qcom/qcom-msm8974.dtsi | 14 +++++++-------
>  arch/arm64/boot/dts/qcom/msm8916.dtsi    | 10 +++++-----
>  arch/arm64/boot/dts/qcom/msm8939.dtsi    |  4 ++--
>  arch/arm64/boot/dts/qcom/msm8953.dtsi    | 10 +++++-----
>  arch/arm64/boot/dts/qcom/msm8976.dtsi    |  8 ++++----
>  arch/arm64/boot/dts/qcom/msm8994.dtsi    |  6 +++---
>  drivers/rpmsg/qcom_smd.c                 |  3 ++-
>  7 files changed, 28 insertions(+), 27 deletions(-)
> ---
> base-commit: 43173e6dbaa227f3107310d4df4a3bacd5e0df33
> change-id: 20240423-apcs-mboxes-12ee6c01a5b3
> 
> Best regards,
> 

Re: [PATCH 1/7] rpmsg: qcom_smd: Don't print error during probe deferral

[Bjorn Andersson]

On Wed, Apr 24, 2024 at 06:23:54PM +0200, Luca Weiss wrote:
> When the mailbox driver has not probed yet, skip printing the error
> message since it's just going to confuse users.
> 
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> ---
>  drivers/rpmsg/qcom_smd.c | 3 ++-
>  1 file changed, 2 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/rpmsg/qcom_smd.c b/drivers/rpmsg/qcom_smd.c
> index 43f601c84b4f..6fc299657adf 100644
> --- a/drivers/rpmsg/qcom_smd.c
> +++ b/drivers/rpmsg/qcom_smd.c
> @@ -1502,7 +1502,8 @@ struct qcom_smd_edge *qcom_smd_register_edge(struct device *parent,
>  
>  	ret = qcom_smd_parse_edge(&edge->dev, node, edge);
>  	if (ret) {
> -		dev_err(&edge->dev, "failed to parse smd edge\n");
> +		if (ret != -EPROBE_DEFER)
> +			dev_err(&edge->dev, "failed to parse smd edge\n");

In the described case, this error message would not be entirely
accurate, and the cause is not accurately captured in devices_deferred.

Unless I'm mistaken, it seems like qcom_smd_parse_edge() will also print
a more useful error in every other case, except after the mbox_chan !=
-ENODEV check..

How about making that:

	if (PTR_ERR(edge->mbox_chan) != -ENODEV) {
		ret = dev_err_probe(dev, PTR_ERR(edge->mbox_chan),
				    "failed to acquire IPC mailbox\n");
		goto put_node;
	}

And then drop the error print here in qcom_smd_register_edge().

It would bring us the devices_deferred tracking, and it would avoid the
double print in all other cases.

Regards,
Bjorn

>  		goto unregister_dev;
>  	}
>  
> 
> -- 
> 2.44.0
> 

Re: [PATCH 0/7] Use mboxes instead of syscon for APCS (arm32 & arm64)

[Bjorn Andersson]

On Wed, Apr 24, 2024 at 06:23:53PM +0200, Luca Weiss wrote:
> The first patch is for removing a bogus error warning I've noticed while
> developing this on msm8226 - there the patches are also coming later for
> this SoC since apcs is getting hooked up to cpufreq there also.
> 
> Apart from usages from the qcom,smsm driver (patches coming!) all other
> usages of the apcs mailbox now go via the mailbox driver - where one is
> used, so some arm32 boards will continue using "qcom,ipc*" properties in
> the short or long term.
> 

Very nice, thank you for cleaning this up.

Regards,
Bjorn

> Only compile-tested apart from msm8953 (tested on sdm632-fairphone-fp3)
> and msm8974 (tested on msm8974pro-fairphone-fp2), but I don't expect any
> complications with this.
> 
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> ---
> Luca Weiss (7):
>       rpmsg: qcom_smd: Don't print error during probe deferral
>       ARM: dts: qcom: msm8974: Use mboxes properties for APCS
>       arm64: dts: qcom: msm8916: Use mboxes properties for APCS
>       arm64: dts: qcom: msm8939: Use mboxes properties for APCS
>       arm64: dts: qcom: msm8953: Use mboxes properties for APCS
>       arm64: dts: qcom: msm8976: Use mboxes properties for APCS
>       arm64: dts: qcom: msm8994: Use mboxes properties for APCS
> 
>  arch/arm/boot/dts/qcom/qcom-msm8974.dtsi | 14 +++++++-------
>  arch/arm64/boot/dts/qcom/msm8916.dtsi    | 10 +++++-----
>  arch/arm64/boot/dts/qcom/msm8939.dtsi    |  4 ++--
>  arch/arm64/boot/dts/qcom/msm8953.dtsi    | 10 +++++-----
>  arch/arm64/boot/dts/qcom/msm8976.dtsi    |  8 ++++----
>  arch/arm64/boot/dts/qcom/msm8994.dtsi    |  6 +++---
>  drivers/rpmsg/qcom_smd.c                 |  3 ++-
>  7 files changed, 28 insertions(+), 27 deletions(-)
> ---
> base-commit: 43173e6dbaa227f3107310d4df4a3bacd5e0df33
> change-id: 20240423-apcs-mboxes-12ee6c01a5b3
> 
> Best regards,
> -- 
> Luca Weiss <luca@z3ntu.xyz>
> 

Re: [PATCH 2/7] ARM: dts: qcom: msm8974: Use mboxes properties for APCS

[Konrad Dybcio]

On 4/24/24 18:23, Luca Weiss wrote:
> Instead of passing the syscon to the various nodes, use the mbox
> interface using the mboxes property.
> 
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH 3/7] arm64: dts: qcom: msm8916: Use mboxes properties for APCS

[Konrad Dybcio]

On 4/24/24 18:23, Luca Weiss wrote:
> Instead of passing the syscon to the various nodes, use the mbox
> interface using the mboxes property.
> 
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH 4/7] arm64: dts: qcom: msm8939: Use mboxes properties for APCS

[Konrad Dybcio]

On 4/24/24 18:23, Luca Weiss wrote:
> Instead of passing the syscon to the various nodes, use the mbox
> interface using the mboxes property.
> 
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH 5/7] arm64: dts: qcom: msm8953: Use mboxes properties for APCS

[Konrad Dybcio]

On 4/24/24 18:23, Luca Weiss wrote:
> Instead of passing the syscon to the various nodes, use the mbox
> interface using the mboxes property.
> 
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH 6/7] arm64: dts: qcom: msm8976: Use mboxes properties for APCS

[Konrad Dybcio]

On 4/24/24 18:23, Luca Weiss wrote:
> Instead of passing the syscon to the various nodes, use the mbox
> interface using the mboxes property.
> 
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH 7/7] arm64: dts: qcom: msm8994: Use mboxes properties for APCS

[Konrad Dybcio]

On 4/24/24 18:24, Luca Weiss wrote:
> Instead of passing the syscon to the various nodes, use the mbox
> interface using the mboxes property.
> 
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad