From: William Qiu <william.qiu@starfivetech.com>
To: <devicetree@vger.kernel.org>, <linux-spi@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <linux-riscv@lists.infradead.org>
Cc: Mark Brown <broonie@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Emil Renner Berthing <kernel@esmil.dk>,
Linus Walleij <linus.walleij@linaro.org>,
William Qiu <william.qiu@starfivetech.com>
Subject: [PATCH v1 2/2] riscv: dts: starfive: Add spi node for JH7110 SoC
Date: Tue, 4 Jul 2023 17:19:44 +0800 [thread overview]
Message-ID: <20230704091948.85247-3-william.qiu@starfivetech.com> (raw)
In-Reply-To: <20230704091948.85247-1-william.qiu@starfivetech.com>
Add spi node for JH7110 SoC.
Co-developed-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
---
.../jh7110-starfive-visionfive-2.dtsi | 52 ++++++++++
arch/riscv/boot/dts/starfive/jh7110.dtsi | 98 +++++++++++++++++++
2 files changed, 150 insertions(+)
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
index 2a6d81609284..a066d2e399c4 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -126,6 +126,20 @@ &i2c6 {
status = "okay";
};
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ status = "okay";
+
+ spi_dev0: spi@0 {
+ compatible = "st,m25p80";
+ pl022,com-mode = <1>;
+ spi-max-frequency = <10000000>;
+ reg = <0>;
+ status = "okay";
+ };
+};
+
&sysgpio {
i2c0_pins: i2c0-0 {
i2c-pins {
@@ -183,6 +197,44 @@ GPOEN_SYS_I2C6_DATA,
};
};
+ spi0_pins: spi0-0 {
+ mosi-pins {
+ pinmux = <GPIOMUX(52, GPOUT_SYS_SPI0_TXD,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-disable;
+ input-disable;
+ input-schmitt-disable;
+ };
+
+ miso-pins {
+ pinmux = <GPIOMUX(53, GPOUT_LOW,
+ GPOEN_DISABLE,
+ GPI_SYS_SPI0_RXD)>;
+ bias-pull-up;
+ input-enable;
+ input-schmitt-enable;
+ };
+
+ sck-pins {
+ pinmux = <GPIOMUX(48, GPOUT_SYS_SPI0_CLK,
+ GPOEN_ENABLE,
+ GPI_SYS_SPI0_CLK)>;
+ bias-disable;
+ input-disable;
+ input-schmitt-disable;
+ };
+
+ ss-pins {
+ pinmux = <GPIOMUX(48, GPOUT_SYS_SPI0_FSS,
+ GPOEN_ENABLE,
+ GPI_SYS_SPI0_FSS)>;
+ bias-disable;
+ input-disable;
+ input-schmitt-disable;
+ };
+ };
+
uart0_pins: uart0-0 {
tx-pins {
pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 4c5fdb905da8..b32611c7cdf7 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -353,6 +353,48 @@ i2c2: i2c@10050000 {
status = "disabled";
};
+ spi0: spi@10060000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0x10060000 0x0 0x10000>;
+ clocks = <&syscrg JH7110_SYSCLK_SPI0_APB>;
+ clock-names = "apb_pclk";
+ resets = <&syscrg JH7110_SYSRST_SPI0_APB>;
+ interrupts = <38>;
+ arm,primecell-periphid = <0x00041022>;
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi1: spi@10070000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0x10070000 0x0 0x10000>;
+ clocks = <&syscrg JH7110_SYSCLK_SPI1_APB>;
+ clock-names = "apb_pclk";
+ resets = <&syscrg JH7110_SYSRST_SPI1_APB>;
+ interrupts = <39>;
+ arm,primecell-periphid = <0x00041022>;
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi2: spi@10080000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0x10080000 0x0 0x10000>;
+ clocks = <&syscrg JH7110_SYSCLK_SPI2_APB>;
+ clock-names = "apb_pclk";
+ resets = <&syscrg JH7110_SYSRST_SPI2_APB>;
+ interrupts = <40>;
+ arm,primecell-periphid = <0x00041022>;
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
uart3: serial@12000000 {
compatible = "snps,dw-apb-uart";
reg = <0x0 0x12000000 0x0 0x10000>;
@@ -440,6 +482,62 @@ i2c6: i2c@12060000 {
status = "disabled";
};
+ spi3: spi@12070000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0x12070000 0x0 0x10000>;
+ clocks = <&syscrg JH7110_SYSCLK_SPI3_APB>;
+ clock-names = "apb_pclk";
+ resets = <&syscrg JH7110_SYSRST_SPI3_APB>;
+ interrupts = <52>;
+ arm,primecell-periphid = <0x00041022>;
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi4: spi@12080000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0x12080000 0x0 0x10000>;
+ clocks = <&syscrg JH7110_SYSCLK_SPI4_APB>;
+ clock-names = "apb_pclk";
+ resets = <&syscrg JH7110_SYSRST_SPI4_APB>;
+ interrupts = <53>;
+ arm,primecell-periphid = <0x00041022>;
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi5: spi@12090000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0x12090000 0x0 0x10000>;
+ clocks = <&syscrg JH7110_SYSCLK_SPI5_APB>;
+ clock-names = "apb_pclk";
+ resets = <&syscrg JH7110_SYSRST_SPI5_APB>;
+ interrupts = <54>;
+ arm,primecell-periphid = <0x00041022>;
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi6: spi@120a0000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0x120A0000 0x0 0x10000>;
+ clocks = <&syscrg JH7110_SYSCLK_SPI6_APB>;
+ clock-names = "apb_pclk";
+ resets = <&syscrg JH7110_SYSRST_SPI6_APB>;
+ interrupts = <55>;
+ arm,primecell-periphid = <0x00041022>;
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
syscrg: clock-controller@13020000 {
compatible = "starfive,jh7110-syscrg";
reg = <0x0 0x13020000 0x0 0x10000>;
--
2.34.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
next prev parent reply other threads:[~2023-07-04 9:20 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-07-04 9:19 [PATCH v1 0/2] Add SPI module for StarFive JH7110 SoC William Qiu
2023-07-04 9:19 ` [PATCH v1 1/2] dt-binding: spi: constrain minItems of clocks and clock-names William Qiu
2023-07-04 9:19 ` William Qiu [this message]
2023-07-04 9:19 ` [PATCH v4 0/3] Add initialization of clock for StarFive JH7110 SoC William Qiu
2023-07-04 9:19 ` [PATCH v4 1/3] dt-bindings: qspi: cdns,qspi-nor: Add clocks " William Qiu
2023-07-04 9:19 ` [PATCH v4 2/3] spi: cadence-quadspi: Add clock configuration for StarFive JH7110 QSPI William Qiu
2023-07-04 9:19 ` [PATCH v4 3/3] riscv: dts: starfive: Add QSPI controller node for StarFive JH7110 SoC William Qiu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230704091948.85247-3-william.qiu@starfivetech.com \
--to=william.qiu@starfivetech.com \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kernel@esmil.dk \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=linux-spi@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).