From: Sam Protsenko <semen.protsenko@linaro.org>
To: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: "Sylwester Nawrocki" <s.nawrocki@samsung.com>,
"Paweł Chmiel" <pawel.mikolaj.chmiel@gmail.com>,
"Chanwoo Choi" <cw00.choi@samsung.com>,
"Linus Walleij" <linus.walleij@linaro.org>,
"Tomasz Figa" <tomasz.figa@gmail.com>,
"Marc Zyngier" <maz@kernel.org>,
"Rob Herring" <robh+dt@kernel.org>,
"Stephen Boyd" <sboyd@kernel.org>,
"Michael Turquette" <mturquette@baylibre.com>,
"Jiri Slaby" <jirislaby@kernel.org>,
"Greg Kroah-Hartman" <gregkh@linuxfoundation.org>,
"Charles Keepax" <ckeepax@opensource.wolfsonmicro.com>,
"Ryu Euiyoul" <ryu.real@samsung.com>,
"Tom Gall" <tom.gall@linaro.org>,
"Sumit Semwal" <sumit.semwal@linaro.org>,
"John Stultz" <john.stultz@linaro.org>,
"Amit Pundir" <amit.pundir@linaro.org>,
devicetree <devicetree@vger.kernel.org>,
"linux-arm Mailing List" <linux-arm-kernel@lists.infradead.org>,
"open list:GPIO SUBSYSTEM" <linux-gpio@vger.kernel.org>,
"Linux Kernel Mailing List" <linux-kernel@vger.kernel.org>,
"Linux Samsung SOC" <linux-samsung-soc@vger.kernel.org>,
"open list:SERIAL DRIVERS" <linux-serial@vger.kernel.org>
Subject: Re: [PATCH v3 7/7] arm64: dts: exynos: Add Exynos850 SoC support
Date: Thu, 12 Aug 2021 20:42:42 +0300 [thread overview]
Message-ID: <CAPLW+4=2msw44EjujeTUvcYJ701iZTPwkVoO3UzZyakspev20A@mail.gmail.com> (raw)
In-Reply-To: <f0e892ce-acd0-7acc-4881-dd67dda6fb38@canonical.com>
On Thu, 12 Aug 2021 at 11:17, Krzysztof Kozlowski
<krzysztof.kozlowski@canonical.com> wrote:
>
> On 11/08/2021 13:48, Sam Protsenko wrote:
> > Samsung Exynos850 is ARMv8-based mobile-oriented SoC.
> >
> > This patch adds minimal SoC support by including next Device Tree nodes:
> >
> > 1. Octa cores (Cortex-A55), supporting PSCI v1.0
> > 2. ARM architecture timer (armv8-timer)
> > 3. Interrupt controller (GIC-400)
> > 4. Pinctrl nodes for GPIO
> > 5. Serial node
> >
> > Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
> > ---
> > Changes in v3:
> > - Used generic fixed clock for serial
> >
> > Changes in v2:
> > * Commit message:
> > - Documented added dts features instead of CPU features
> >
> > * exynos850-usi.dtsi:
> > - Removed, moved everything to exynos850.dtsi
> >
> > * exynos850.dtsi:
> > - Root node:
> > - Added comment about engineering name (Exynos3830)
> > - Renamed pinctrl nodes, adding domain names
> > - Used hard coded IRQ numbers instead of named constants everywhere
> > - Added soc node, moved next nodes there: gic, clock, pinctrls and
> > serial
> > - Used address-cells=1 for soc node and removed unneeded 0x0 from
> > reg properties
> > - Moved exynos850-pinctrl.dtsi include line to the end of
> > exynos850.dtsi
> > - Coding style fixes
> > - cpus:
> > - Used address-cells=1 for cpus node
> > - Renamed cpu@0001 to cpu@1, and so on
> > - Left only "arm,cortex-a55" for cpus compatible
> > - Renamed reg = <0x0001> to <0x1> for cpus
> > - armv8 timer:
> > - Add comment about missing HV timer IRQ to armv8 timer node
> > - Removed not existing properties from armv8 timer node
> > - Fixed cpu number in CPU_MASK()
> > - Removed obsolete clock-frequency property
> > - GIC:
> > - Fixed GIC type to be GIC-400
> > - Fixed size of GIC's 2nd region to be 0x2000
> > - serial node:
> > - Hard coded clock number for serial_0 for now; will replace with
> > named const once proper clock driver is implemented
> > - Removed gate_uart_clk0 clock from serial_0, as that clock is not
> > supported in serial driver anyway (yet)
> > - clock node:
> > - Fixed clock controller node name (@0x12.. -> @12..)
> >
> > * exynos850-pinctrl.dtsi:
> > - Referenced pinctrl nodes instead of defining those again in root node
> > - Fixed interrupt-cells (3 -> 2)
> > - Fixed USI related comments for pin config nodes
> > - Removed decon_f_te_* and fm_lna_en nodes (won't be used)
> > - Reordered pin config nodes by pin numbers
> > - Improved all comments
> > - Used existing named constants for pin-function and pin-pud
> > - Fixed node names (used hyphens instead of underscore)
> > - Fixed warnings found in W=1 build
> >
> > .../boot/dts/exynos/exynos850-pinctrl.dtsi | 748 ++++++++++++++++++
> > arch/arm64/boot/dts/exynos/exynos850.dtsi | 261 ++++++
> > 2 files changed, 1009 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> > create mode 100644 arch/arm64/boot/dts/exynos/exynos850.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> > new file mode 100644
> > index 000000000000..ba5d5f33e2f6
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> > @@ -0,0 +1,748 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Samsung's Exynos850 SoC pin-mux and pin-config device tree source
> > + *
> > + * Copyright (C) 2017 Samsung Electronics Co., Ltd.
> > + * Copyright (C) 2021 Linaro Ltd.
> > + *
> > + * Samsung's Exynos850 SoC pin-mux and pin-config options are listed as device
> > + * tree nodes in this file.
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include <dt-bindings/pinctrl/samsung.h>
> > +
> > +&pinctrl_alive {
> > + gpa0: gpa0 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + gpa1: gpa1 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + gpa2: gpa2 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + gpa3: gpa3 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + gpa4: gpa4 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + gpq0: gpq0 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + /* I2C5 (also called CAM_PMIC_I2C in TRM) */
> > + i2c5_bus: i2c5-bus {
> > + samsung,pins = "gpa3-5", "gpa3-6";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + /* I2C6 (also called MOTOR_I2C in TRM) */
> > + i2c6_bus: i2c6-bus {
> > + samsung,pins = "gpa3-7", "gpa4-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + /* USI: UART */
> > + uart0_bus: uart0-bus {
> > + samsung,pins = "gpq0-0", "gpq0-1";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + };
> > +};
> > +
> > +&pinctrl_cmgp {
> > + gpm0: gpm0 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + gpm1: gpm1 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + gpm2: gpm2 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + gpm3: gpm3 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + gpm4: gpm4 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + gpm5: gpm5 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + /* USI_CMGP0: HSI2C function */
> > + hsi2c3_bus: hsi2c3-bus {
> > + samsung,pins = "gpm0-0", "gpm1-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <0>;
>
> There are also macros for DRV.
>
Unfortunately, existing DRV macros won't work for Exynos850. DRV
constants have different meaning for different GPIO domains in
Exynos850, so I thought introducing several groups of DRV constants
might be confusing. But please let me know if you still want me do
that.
> I assume you checked whether the actual values of FUNC/PULL/DRV macros
> match Exynos850 datasheet.
>
Yep, they are good.
> > + };
> > +
> > + /* USI_CMGP0: UART function (4 pins, Auto Flow Control) */
> > + uart1_bus_single: uart1-bus {
> > + samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0", "gpm3-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + };
> > +
> > + /* USI_CMGP0: UART function (2 pins, Non-Auto Flow Control) */
> > + uart1_bus_dual: uart1-bus-dual {
> > + samsung,pins = "gpm0-0", "gpm1-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + };
> > +
> > + /* USI_CMGP0: SPI function */
> > + spi1_bus: spi1-bus {
> > + samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + spi1_cs: spi1-cs {
> > + samsung,pins = "gpm3-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + spi1_cs_func: spi1-cs-func {
> > + samsung,pins = "gpm3-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + /* USI_CMGP1: HSI2C function */
> > + hsi2c4_bus: hsi2c4-bus {
> > + samsung,pins = "gpm4-0", "gpm5-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + /* USI_CMGP1: UART function (4 pins, Auto Flow Control) */
> > + uart2_bus_single: uart2-bus {
> > + samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0", "gpm7-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + };
> > +
> > + /* USI_CMGP1: UART function (2 pins, Non-Auto Flow Control) */
> > + uart2_bus_dual: uart2-bus-dual {
> > + samsung,pins = "gpm4-0", "gpm5-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + };
> > +
> > + /* USI_CMGP1: SPI function */
> > + spi2_bus: spi2-bus {
> > + samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + spi2_cs: spi2-cs {
> > + samsung,pins = "gpm7-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + spi2_cs_func: spi2-cs-func {
> > + samsung,pins = "gpm7-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <0>;
> > + };
> > +};
> > +
> > +&pinctrl_aud {
> > + gpb0: gpb0 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpb1: gpb1 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + aud_codec_mclk: aud-codec-mclk {
> > + samsung,pins = "gpb0-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > + };
> > +
> > + aud_codec_mclk_idle: aud-codec-mclk-idle {
> > + samsung,pins = "gpb0-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > + };
> > +
> > + aud_i2s0_bus: aud-i2s0-bus {
> > + samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > + };
> > +
> > + aud_i2s0_idle: aud-i2s0-idle {
> > + samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > + };
> > +
> > + aud_i2s1_bus: aud-i2s1-bus {
> > + samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > + };
> > +
> > + aud_i2s1_idle: aud-i2s1-idle {
> > + samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > + };
> > +
> > + aud_fm_bus: aud-fm-bus {
> > + samsung,pins = "gpb1-4";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > + };
> > +
> > + aud_fm_idle: aud-fm-idle {
> > + samsung,pins = "gpb1-4";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > + };
> > +};
> > +
> > +&pinctrl_hsi {
> > + gpf2: gpf2 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + sd2_clk: sd2-clk {
> > + samsung,pins = "gpf2-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <2>;
> > + };
> > +
> > + sd2_clk_fast_slew_rate_1x: sd2-clk-fast-slew-rate-1x {
> > + samsung,pins = "gpf2-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + sd2_clk_fast_slew_rate_1_5x: sd2-clk-fast-slew-rate-1-5x {
> > + samsung,pins = "gpf2-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <1>;
> > + };
> > +
> > + sd2_clk_fast_slew_rate_2x: sd2-clk-fast-slew-rate-2x {
> > + samsung,pins = "gpf2-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <2>;
> > + };
> > +
> > + sd2_clk_fast_slew_rate_2_5x: sd2-clk-fast-slew-rate-2-5x {
> > + samsung,pins = "gpf2-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <3>;
> > + };
> > +
> > + sd2_clk_fast_slew_rate_3x: sd2-clk-fast-slew-rate-3x {
> > + samsung,pins = "gpf2-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <4>;
> > + };
> > +
> > + sd2_clk_fast_slew_rate_4x: sd2-clk-fast-slew-rate-4x {
> > + samsung,pins = "gpf2-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <5>;
> > + };
> > +
> > + sd2_cmd: sd2-cmd {
> > + samsung,pins = "gpf2-1";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <2>;
> > + };
> > +
> > + sd2_bus1: sd2-bus-width1 {
> > + samsung,pins = "gpf2-2";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <2>;
> > + };
> > +
> > + sd2_bus4: sd2-bus-width4 {
> > + samsung,pins = "gpf2-3", "gpf2-4", "gpf2-5";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <2>;
> > + };
> > +
> > + sd2_pins_as_pdn: sd2-pins-as-pdn {
> > + samsung,pins = "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
> > + "gpf2-4", "gpf2-5";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > + };
> > +};
> > +
> > +&pinctrl_core {
> > + gpf0: gpf0 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpf1: gpf1 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + sd0_clk: sd0-clk {
> > + samsung,pins = "gpf0-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <3>;
> > + };
> > +
> > + sd0_clk_fast_slew_rate_1x: sd0-clk-fast-slew-rate-1x {
> > + samsung,pins = "gpf0-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <1>;
> > + };
> > +
> > + sd0_clk_fast_slew_rate_2x: sd0-clk-fast-slew-rate-2x {
> > + samsung,pins = "gpf0-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <2>;
> > + };
> > +
> > + sd0_clk_fast_slew_rate_3x: sd0-clk-fast-slew-rate-3x {
> > + samsung,pins = "gpf0-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <2>;
> > + };
> > +
> > + sd0_clk_fast_slew_rate_4x: sd0-clk-fast-slew-rate-4x {
> > + samsung,pins = "gpf0-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <3>;
> > + };
> > +
> > + sd0_cmd: sd0-cmd {
> > + samsung,pins = "gpf0-1";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <3>;
> > + };
> > +
> > + sd0_rdqs: sd0-rdqs {
> > + samsung,pins = "gpf0-2";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > + samsung,pin-drv = <3>;
> > + };
> > +
> > + sd0_nreset: sd0-nreset {
> > + samsung,pins = "gpf0-3";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <3>;
> > + };
> > +
> > + sd0_bus1: sd0-bus-width1 {
> > + samsung,pins = "gpf1-0";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <3>;
> > + };
> > +
> > + sd0_bus4: sd0-bus-width4 {
> > + samsung,pins = "gpf1-1", "gpf1-2", "gpf1-3";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <3>;
> > + };
> > +
> > + sd0_bus8: sd0-bus-width8 {
> > + samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <3>;
> > + };
> > +};
> > +
> > +&pinctrl_peri {
> > + gpg0: gpg0 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpp0: gpp0 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > + gpp1: gpp1 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpp2: gpp2 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpg1: gpg1 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpg2: gpg2 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpg3: gpg3 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpc0: gpc0 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + gpc1: gpc1 {
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + };
> > +
> > + /* USI: HSI2C0 */
> > + hsi2c0_bus: hsi2c0-bus {
> > + samsung,pins = "gpc1-0", "gpc1-1";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + /* USI: HSI2C1 */
> > + hsi2c1_bus: hsi2c1-bus {
> > + samsung,pins = "gpc1-2", "gpc1-3";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + /* USI: HSI2C2 */
> > + hsi2c2_bus: hsi2c2-bus {
> > + samsung,pins = "gpc1-4", "gpc1-5";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + /* USI: SPI */
> > + spi0_bus: spi0-bus {
> > + samsung,pins = "gpp2-0", "gpp2-2", "gpp2-3";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + spi0_cs: spi0-cs {
> > + samsung,pins = "gpp2-1";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + spi0_cs_func: spi0-cs-func {
> > + samsung,pins = "gpp2-1";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + i2c0_bus: i2c0-bus {
> > + samsung,pins = "gpp0-0", "gpp0-1";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + i2c1_bus: i2c1-bus {
> > + samsung,pins = "gpp0-2", "gpp0-3";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + i2c2_bus: i2c2-bus {
> > + samsung,pins = "gpp0-4", "gpp0-5";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + i2c3_bus: i2c3-bus {
> > + samsung,pins = "gpp1-0", "gpp1-1";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + i2c4_bus: i2c4-bus {
> > + samsung,pins = "gpp1-2", "gpp1-3";
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > + samsung,pin-drv = <0>;
> > + };
> > +
> > + sensor_mclk0_in: sensor-mclk0-in {
> > + samsung,pins = "gpc0-0";
>
> All these gpc0 go before hsi2c0_bus node (to have them ordered by
> datasheet pin name).
>
Done.
> > + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > + samsung,pin-drv = <2>;
> > + };
> > +
>
> Rest looks good but anyway will wait for the board DTS. :)
>
Sure. I'll probably send next patch series only when the board gets
announced, and will include board's dts of course.
> Best regards,
> Krzysztof
next prev parent reply other threads:[~2021-08-12 17:42 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-08-11 11:48 [PATCH v3 0/7] Add minimal support for Exynos850 SoC Sam Protsenko
2021-08-11 11:48 ` [PATCH v3 1/7] dt-bindings: pinctrl: samsung: Add Exynos850 doc Sam Protsenko
2021-08-11 11:48 ` [PATCH v3 2/7] pinctrl: samsung: Add Exynos850 SoC specific data Sam Protsenko
2021-08-11 11:48 ` [PATCH v3 3/7] dt-bindings: serial: samsung: Add Exynos850 doc Sam Protsenko
2021-08-17 21:21 ` Rob Herring
2021-09-06 16:27 ` Sam Protsenko
2021-09-07 7:52 ` Krzysztof Kozlowski
2021-08-11 11:48 ` [PATCH v3 4/7] tty: serial: samsung: Init USI to keep clocks running Sam Protsenko
2021-08-11 11:48 ` [PATCH v3 5/7] tty: serial: samsung: Fix driver data macros style Sam Protsenko
2021-08-11 11:48 ` [PATCH v3 6/7] tty: serial: samsung: Add Exynos850 SoC data Sam Protsenko
2021-08-11 11:48 ` [PATCH v3 7/7] arm64: dts: exynos: Add Exynos850 SoC support Sam Protsenko
2021-08-12 8:17 ` Krzysztof Kozlowski
2021-08-12 17:42 ` Sam Protsenko [this message]
2021-08-16 9:45 ` Krzysztof Kozlowski
2021-08-17 18:42 ` Rob Herring
2021-08-21 20:04 ` Sam Protsenko
2021-08-13 7:41 ` [PATCH v3 0/7] Add minimal support for Exynos850 SoC Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAPLW+4=2msw44EjujeTUvcYJ701iZTPwkVoO3UzZyakspev20A@mail.gmail.com' \
--to=semen.protsenko@linaro.org \
--cc=amit.pundir@linaro.org \
--cc=ckeepax@opensource.wolfsonmicro.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jirislaby@kernel.org \
--cc=john.stultz@linaro.org \
--cc=krzysztof.kozlowski@canonical.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=maz@kernel.org \
--cc=mturquette@baylibre.com \
--cc=pawel.mikolaj.chmiel@gmail.com \
--cc=robh+dt@kernel.org \
--cc=ryu.real@samsung.com \
--cc=s.nawrocki@samsung.com \
--cc=sboyd@kernel.org \
--cc=sumit.semwal@linaro.org \
--cc=tom.gall@linaro.org \
--cc=tomasz.figa@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).