From: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
To: <linux-kernel@vger.kernel.org>
Cc: <linux-serial@vger.kernel.org>, <gregkh@linuxfoundation.org>,
<jirislaby@kernel.org>, <ilpo.jarvinen@linux.intel.com>,
<macro@orcam.me.uk>, <andriy.shevchenko@linux.intel.com>,
<lukas@wunner.de>, <cang1@live.co.uk>,
<matthew.gerlach@linux.intel.com>, <deller@gmx.de>,
<phil.edworthy@renesas.com>, <geert+renesas@glider.be>,
<marpagan@redhat.com>, <u.kleine-koenig@pengutronix.de>,
<etremblay@distech-controls.com>, <wander@redhat.com>,
Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Subject: [PATCH v11 tty-next 4/4] serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
Date: Sat, 4 Feb 2023 11:01:38 +0530 [thread overview]
Message-ID: <20230204053138.2520105-5-kumaravel.thiagarajan@microchip.com> (raw)
In-Reply-To: <20230204053138.2520105-1-kumaravel.thiagarajan@microchip.com>
pci1xxxx's quad-uart function has the capability to wake up UART
from suspend state. Enable wakeup before entering into suspend and
disable wakeup on resume.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
---
Changes in v11:
- No Change
Changes in v10:
- No Change
Changes in v9:
- No Change
Changes in v8:
- No Change
Changes in v7:
- No Change
Changes in v6:
- No Change
Changes in v5:
- Corrected commit message
Changes in v4:
- No Change
Changes in v3:
- Handled race condition in suspend and resume callbacks
Changes in v2:
- Use DEFINE_SIMPLE_DEV_PM_OPS instead of SIMPLE_DEV_PM_OPS.
- Use pm_sleep_ptr instead of CONFIG_PM_SLEEP.
- Change the return data type of pci1xxxx_port_suspend to bool from int.
---
drivers/tty/serial/8250/8250_pci1xxxx.c | 115 ++++++++++++++++++++++++
1 file changed, 115 insertions(+)
diff --git a/drivers/tty/serial/8250/8250_pci1xxxx.c b/drivers/tty/serial/8250/8250_pci1xxxx.c
index 58f47d18f7d8..a3b25779d921 100644
--- a/drivers/tty/serial/8250/8250_pci1xxxx.c
+++ b/drivers/tty/serial/8250/8250_pci1xxxx.c
@@ -212,6 +212,116 @@ static const struct serial_rs485 pci1xxxx_rs485_supported = {
/* Delay RTS before send is not supported */
};
+static bool pci1xxxx_port_suspend(int line)
+{
+ struct uart_8250_port *up = serial8250_get_port(line);
+ struct uart_port *port = &up->port;
+ struct tty_port *tport = &port->state->port;
+ unsigned long flags;
+ bool ret = false;
+ u8 wakeup_mask;
+
+ mutex_lock(&tport->mutex);
+ if (port->suspended == 0 && port->dev) {
+ wakeup_mask = readb(up->port.membase + UART_WAKE_MASK_REG);
+
+ spin_lock_irqsave(&port->lock, flags);
+ port->mctrl &= ~TIOCM_OUT2;
+ port->ops->set_mctrl(port, port->mctrl);
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ ret = (wakeup_mask & UART_WAKE_SRCS) != UART_WAKE_SRCS;
+ }
+
+ writeb(UART_WAKE_SRCS, port->membase + UART_WAKE_REG);
+ mutex_unlock(&tport->mutex);
+
+ return ret;
+}
+
+static void pci1xxxx_port_resume(int line)
+{
+ struct uart_8250_port *up = serial8250_get_port(line);
+ struct uart_port *port = &up->port;
+ struct tty_port *tport = &port->state->port;
+ unsigned long flags;
+
+ mutex_lock(&tport->mutex);
+ writeb(UART_BLOCK_SET_ACTIVE, port->membase + UART_ACTV_REG);
+ writeb(UART_WAKE_SRCS, port->membase + UART_WAKE_REG);
+
+ if (port->suspended == 0) {
+ spin_lock_irqsave(&port->lock, flags);
+ port->mctrl |= TIOCM_OUT2;
+ port->ops->set_mctrl(port, port->mctrl);
+ spin_unlock_irqrestore(&port->lock, flags);
+ }
+ mutex_unlock(&tport->mutex);
+}
+
+static int pci1xxxx_suspend(struct device *dev)
+{
+ struct pci1xxxx_8250 *priv = dev_get_drvdata(dev);
+ struct pci_dev *pcidev = to_pci_dev(dev);
+ bool wakeup = false;
+ unsigned int data;
+ void __iomem *p;
+ int i;
+
+ for (i = 0; i < priv->nr; i++) {
+ if (priv->line[i] >= 0) {
+ serial8250_suspend_port(priv->line[i]);
+ wakeup |= pci1xxxx_port_suspend(priv->line[i]);
+ }
+ }
+
+ p = pci_ioremap_bar(pcidev, 0);
+ if (!p) {
+ dev_err(dev, "remapping of bar 0 memory failed");
+ return -ENOMEM;
+ }
+
+ data = readl(p + UART_RESET_REG);
+ writel(data | UART_RESET_D3_RESET_DISABLE, p + UART_RESET_REG);
+
+ if (wakeup)
+ writeb(UART_PCI_CTRL_D3_CLK_ENABLE, p + UART_PCI_CTRL_REG);
+
+ iounmap(p);
+ device_set_wakeup_enable(dev, true);
+ pci_wake_from_d3(pcidev, true);
+
+ return 0;
+}
+
+static int pci1xxxx_resume(struct device *dev)
+{
+ struct pci1xxxx_8250 *priv = dev_get_drvdata(dev);
+ struct pci_dev *pcidev = to_pci_dev(dev);
+ unsigned int data;
+ void __iomem *p;
+ int i;
+
+ p = pci_ioremap_bar(pcidev, 0);
+ if (!p) {
+ dev_err(dev, "remapping of bar 0 memory failed");
+ return -ENOMEM;
+ }
+
+ data = readl(p + UART_RESET_REG);
+ writel(data & ~UART_RESET_D3_RESET_DISABLE, p + UART_RESET_REG);
+ iounmap(p);
+
+ for (i = 0; i < priv->nr; i++) {
+ if (priv->line[i] >= 0) {
+ pci1xxxx_port_resume(priv->line[i]);
+ serial8250_resume_port(priv->line[i]);
+ }
+ }
+
+ return 0;
+}
+
static int pci1xxxx_setup(struct pci_dev *pdev,
struct uart_8250_port *port, int port_idx)
{
@@ -352,6 +462,8 @@ static void pci1xxxx_serial_remove(struct pci_dev *dev)
pci_iounmap(dev, priv->membase);
}
+static DEFINE_SIMPLE_DEV_PM_OPS(pci1xxxx_pm_ops, pci1xxxx_suspend, pci1xxxx_resume);
+
static const struct pci_device_id pci1xxxx_pci_tbl[] = {
{ PCI_VDEVICE(EFAR, PCI_DEVICE_ID_EFAR_PCI11010) },
{ PCI_VDEVICE(EFAR, PCI_DEVICE_ID_EFAR_PCI11101) },
@@ -366,6 +478,9 @@ static struct pci_driver pci1xxxx_pci_driver = {
.name = "pci1xxxx serial",
.probe = pci1xxxx_serial_probe,
.remove = pci1xxxx_serial_remove,
+ .driver = {
+ .pm = pm_sleep_ptr(&pci1xxxx_pm_ops),
+ },
.id_table = pci1xxxx_pci_tbl,
};
module_pci_driver(pci1xxxx_pci_driver);
--
2.25.1
next prev parent reply other threads:[~2023-02-03 16:57 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-02-04 5:31 [PATCH v11 tty-next 0/4] serial: 8250_pci1xxxx: Add driver for the pci1xxxx's quad-uart function Kumaravel Thiagarajan
2023-02-04 5:31 ` [PATCH v11 tty-next 1/4] serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c Kumaravel Thiagarajan
2023-02-04 5:30 ` kernel test robot
2023-02-05 0:59 ` kernel test robot
2023-02-06 11:40 ` Andy Shevchenko
2023-02-06 11:41 ` Andy Shevchenko
2023-02-04 5:31 ` [PATCH v11 tty-next 2/4] serial: 8250_pci1xxxx: Add driver for quad-uart support Kumaravel Thiagarajan
2023-02-04 5:31 ` [PATCH v11 tty-next 3/4] serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver Kumaravel Thiagarajan
2023-02-04 5:31 ` Kumaravel Thiagarajan [this message]
2023-02-06 11:37 ` [PATCH v11 tty-next 0/4] serial: 8250_pci1xxxx: Add driver for the pci1xxxx's quad-uart function Andy Shevchenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230204053138.2520105-5-kumaravel.thiagarajan@microchip.com \
--to=kumaravel.thiagarajan@microchip.com \
--cc=andriy.shevchenko@linux.intel.com \
--cc=cang1@live.co.uk \
--cc=deller@gmx.de \
--cc=etremblay@distech-controls.com \
--cc=geert+renesas@glider.be \
--cc=gregkh@linuxfoundation.org \
--cc=ilpo.jarvinen@linux.intel.com \
--cc=jirislaby@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=lukas@wunner.de \
--cc=macro@orcam.me.uk \
--cc=marpagan@redhat.com \
--cc=matthew.gerlach@linux.intel.com \
--cc=phil.edworthy@renesas.com \
--cc=tharunkumar.pasumarthi@microchip.com \
--cc=u.kleine-koenig@pengutronix.de \
--cc=wander@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).