From: Cyril Chemparathy <cyril-l0cyMroinI0@public.gmane.org>
To: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org,
spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org,
sameo-VuQAYsv1563Yd54FQh9/CA@public.gmane.org,
rpurdie-Fm38FmjxZ/leoWH0uzbU5w@public.gmane.org,
dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org
Cc: linux-arm-kernel-xIg/pKzrS19vn6HldHNs0ANdhmdF6hFW@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: [PATCH v8 00/11] tnetv107x ssp drivers
Date: Tue, 18 Jan 2011 14:21:34 -0500 [thread overview]
Message-ID: <1295378505-15221-1-git-send-email-cyril@ti.com> (raw)
TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port
device. It has a built-in programmable execution engine that can be programmed
to operate as almost any serial bus (I2C, SPI, EasyScale, and others).
This patch series implements a driver stack that looks like the following:
+--------+
| eeprom | . . .
+--------+
+-----------+ +--------------+ +---------+
| regulator | . . . | i2c-gpio | | 1-wire | . . .
+-----------+ +--------------+ +---------+
+----------------------+ +--------------------------------+
| ssp-spi | | ssp-gpio |
+----------------------+ +--------------------------------+
+----------------------------------------------------------+
| ssp |
+----------------------------------------------------------+
Changes between v8 and v7 of this series:
- Reorder commits, removed regulator driver patch (already upstreamed)
- Renamed static function definitions to keep namespace clean (mfd, gpio)
- Removed instance pdata in mfd driver
Changes between v7 and v6 of this series:
- Workaround for iosel2 register not reading back set bits.
- Update backlight status once probe succeeds.
Changes between v6 and v5 of this series:
- Changed initcalls to module_init() across all drivers. This series now
uses a late_initcall() in the board to delay initialization of gpio and
regulator dependent devices.
Changes between v5 and v4 of this series:
- Moved drivers from misc/gpio/spi to mfd
- Removed implicit init-time iosel setup
- Minor cleanups in backlight driver
Changes between v3 and v4 of this series:
- Replaced polled wait for sequence termination with interrupt
- Improved locking within SSP driver
- Other minor cleanups
Changes between v2 and v3 of this series:
- Minor cleanups in Kconfig and Makefile ordering
Changes between v1 and v2 of this series:
- Replaced open()/close() semantics with dynamic platform_device
registration on SSP probe.
- Removed user-land interface to regulator registers
- More sensible regulator constraints
- Other minor cleanups
Cyril Chemparathy (11):
mfd: add driver for sequencer serial port
spi: add ti-ssp spi master driver
gpio: add ti-ssp gpio driver
backlight: add support for tps6116x controller
davinci: add tnetv107x ssp platform device
davinci: add ssp config for tnetv107x evm board
davinci: add spi devices on tnetv107x evm
davinci: add tnetv107x evm regulators
davinci: add tnetv107x evm ti-ssp gpio device
davinci: add tnetv107x evm backlight device
davinci: add tnetv107x evm i2c eeprom device
arch/arm/mach-davinci/board-tnetv107x-evm.c | 197 ++++++++++
arch/arm/mach-davinci/devices-tnetv107x.c | 25 ++
arch/arm/mach-davinci/include/mach/tnetv107x.h | 2 +
arch/arm/mach-davinci/tnetv107x.c | 2 +-
drivers/gpio/Kconfig | 10 +
drivers/gpio/Makefile | 1 +
drivers/gpio/ti-ssp-gpio.c | 207 ++++++++++
drivers/mfd/Kconfig | 11 +
drivers/mfd/Makefile | 1 +
drivers/mfd/ti-ssp.c | 476 ++++++++++++++++++++++++
drivers/spi/Kconfig | 10 +
drivers/spi/Makefile | 1 +
drivers/spi/ti-ssp-spi.c | 402 ++++++++++++++++++++
drivers/video/backlight/Kconfig | 7 +
drivers/video/backlight/Makefile | 2 +-
drivers/video/backlight/tps6116x.c | 299 +++++++++++++++
include/linux/mfd/ti_ssp.h | 97 +++++
17 files changed, 1748 insertions(+), 2 deletions(-)
create mode 100644 drivers/gpio/ti-ssp-gpio.c
create mode 100644 drivers/mfd/ti-ssp.c
create mode 100644 drivers/spi/ti-ssp-spi.c
create mode 100644 drivers/video/backlight/tps6116x.c
create mode 100644 include/linux/mfd/ti_ssp.h
next reply other threads:[~2011-01-18 19:21 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-01-18 19:21 Cyril Chemparathy [this message]
2011-01-18 19:21 ` [PATCH v8 01/11] mfd: add driver for sequencer serial port Cyril Chemparathy
2011-01-19 17:43 ` Kevin Hilman
2011-01-31 0:40 ` Samuel Ortiz
2011-03-17 7:33 ` Nori, Sekhar
2011-01-18 19:21 ` [PATCH v8 02/11] spi: add ti-ssp spi master driver Cyril Chemparathy
2011-01-18 19:21 ` [PATCH v8 05/11] davinci: add tnetv107x ssp platform device Cyril Chemparathy
[not found] ` <1295378505-15221-1-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2011-01-18 19:21 ` [PATCH v8 03/11] gpio: add ti-ssp gpio driver Cyril Chemparathy
[not found] ` <1295378505-15221-4-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2011-02-28 12:34 ` Nori, Sekhar
2011-03-17 18:45 ` Grant Likely
[not found] ` <20110317184514.GP9597-MrY2KI0G/OVr83L8+7iqerDks+cytr/Z@public.gmane.org>
2011-03-18 6:30 ` Nori, Sekhar
2011-01-18 19:21 ` [PATCH v8 04/11] backlight: add support for tps6116x controller Cyril Chemparathy
2011-01-19 17:42 ` Kevin Hilman
2011-01-18 19:21 ` [PATCH v8 06/11] davinci: add ssp config for tnetv107x evm board Cyril Chemparathy
2011-01-18 19:21 ` [PATCH v8 08/11] davinci: add tnetv107x evm regulators Cyril Chemparathy
2011-01-18 19:21 ` [PATCH v8 10/11] davinci: add tnetv107x evm backlight device Cyril Chemparathy
2011-01-18 19:21 ` [PATCH v8 11/11] davinci: add tnetv107x evm i2c eeprom device Cyril Chemparathy
2011-01-18 19:21 ` [PATCH v8 07/11] davinci: add spi devices on tnetv107x evm Cyril Chemparathy
2011-01-18 19:21 ` [PATCH v8 09/11] davinci: add tnetv107x evm ti-ssp gpio device Cyril Chemparathy
-- strict thread matches above, loose matches on Subject: below --
2011-01-17 19:15 [PATCH v8 00/11] tnetv107x ssp drivers Cyril Chemparathy
[not found] ` <1295291725-32509-1-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2011-01-18 18:13 ` Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1295378505-15221-1-git-send-email-cyril@ti.com \
--to=cyril-l0cymroini0@public.gmane.org \
--cc=davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org \
--cc=dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
--cc=linux-arm-kernel-xIg/pKzrS19vn6HldHNs0ANdhmdF6hFW@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=rpurdie-Fm38FmjxZ/leoWH0uzbU5w@public.gmane.org \
--cc=sameo-VuQAYsv1563Yd54FQh9/CA@public.gmane.org \
--cc=spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).