[PATCH AUTOSEL 5.17 027/135] spi: spi-rspi: Remove setting {src,dst}_{addr,addr_width} based on DMA direction

[PATCH AUTOSEL 5.17 027/135] spi: spi-rspi: Remove setting {src,dst}_{addr,addr_width} based on DMA direction

[Sasha Levin]

From: Biju Das <biju.das.jz@bp.renesas.com>

[ Upstream commit 6f381481a5b236cb53d6de2c49c6ef83a4d0f432 ]

The direction field in the DMA config is deprecated. The rspi driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.

This patch fixes the issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220411173115.6619-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/spi/spi-rspi.c | 15 ++++++---------
 1 file changed, 6 insertions(+), 9 deletions(-)

diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c
index bd5708d7e5a1..7a014eeec2d0 100644
--- a/drivers/spi/spi-rspi.c
+++ b/drivers/spi/spi-rspi.c
@@ -1108,14 +1108,11 @@ static struct dma_chan *rspi_request_dma_chan(struct device *dev,
 	}
 
 	memset(&cfg, 0, sizeof(cfg));
+	cfg.dst_addr = port_addr + RSPI_SPDR;
+	cfg.src_addr = port_addr + RSPI_SPDR;
+	cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
 	cfg.direction = dir;
-	if (dir == DMA_MEM_TO_DEV) {
-		cfg.dst_addr = port_addr;
-		cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
-	} else {
-		cfg.src_addr = port_addr;
-		cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
-	}
 
 	ret = dmaengine_slave_config(chan, &cfg);
 	if (ret) {
@@ -1146,12 +1143,12 @@ static int rspi_request_dma(struct device *dev, struct spi_controller *ctlr,
 	}
 
 	ctlr->dma_tx = rspi_request_dma_chan(dev, DMA_MEM_TO_DEV, dma_tx_id,
-					     res->start + RSPI_SPDR);
+					     res->start);
 	if (!ctlr->dma_tx)
 		return -ENODEV;
 
 	ctlr->dma_rx = rspi_request_dma_chan(dev, DMA_DEV_TO_MEM, dma_rx_id,
-					     res->start + RSPI_SPDR);
+					     res->start);
 	if (!ctlr->dma_rx) {
 		dma_release_channel(ctlr->dma_tx);
 		ctlr->dma_tx = NULL;
-- 
2.35.1

[PATCH AUTOSEL 5.17 082/135] spi: stm32-qspi: Fix wait_cmd timeout in APM mode

[Sasha Levin]

From: Patrice Chotard <patrice.chotard@foss.st.com>

[ Upstream commit d83d89ea68b4726700fa87b22db075e4217e691c ]

In APM mode, TCF and TEF flags are not set. To avoid timeout in
stm32_qspi_wait_cmd(), don't check if TCF/TEF are set.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: eberhard.stoll@kontron.de
Link: https://lore.kernel.org/r/20220511074644.558874-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/spi/spi-stm32-qspi.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/spi/spi-stm32-qspi.c b/drivers/spi/spi-stm32-qspi.c
index ffdc55f87e82..dd38cb8ffbc2 100644
--- a/drivers/spi/spi-stm32-qspi.c
+++ b/drivers/spi/spi-stm32-qspi.c
@@ -308,7 +308,8 @@ static int stm32_qspi_wait_cmd(struct stm32_qspi *qspi,
 	if (!op->data.nbytes)
 		goto wait_nobusy;
 
-	if (readl_relaxed(qspi->io_base + QSPI_SR) & SR_TCF)
+	if ((readl_relaxed(qspi->io_base + QSPI_SR) & SR_TCF) ||
+	    qspi->fmode == CCR_FMODE_APM)
 		goto out;
 
 	reinit_completion(&qspi->data_completion);
-- 
2.35.1