[PATCH V12 0/5] Add i.MX7ULP EVK PWM backlight support

[PATCH V12 0/5] Add i.MX7ULP EVK PWM backlight support

[Anson Huang]

i.MX7ULP EVK board has MIPI-DSI display, its backlight is supplied by
TPM PWM module, this patch set enables i.MX7ULP TPM PWM driver support
and also add backlight support for MIPI-DSI display.

Changes since V11:
	- ONLY add a function comment in drivers/pwm/pwm-imx-tpm.c

Anson Huang (5):
  dt-bindings: pwm: Add i.MX TPM PWM binding
  pwm: Add i.MX TPM PWM driver support
  ARM: imx_v6_v7_defconfig: Add TPM PWM support by default
  ARM: dts: imx7ulp: Add tpm pwm support
  ARM: dts: imx7ulp-evk: Add backlight support

 .../devicetree/bindings/pwm/imx-tpm-pwm.txt        |  22 +
 arch/arm/boot/dts/imx7ulp-evk.dts                  |  20 +
 arch/arm/boot/dts/imx7ulp.dtsi                     |  10 +
 arch/arm/configs/imx_v6_v7_defconfig               |   1 +
 drivers/pwm/Kconfig                                |  11 +
 drivers/pwm/Makefile                               |   1 +
 drivers/pwm/pwm-imx-tpm.c                          | 448 +++++++++++++++++++++
 7 files changed, 513 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt
 create mode 100644 drivers/pwm/pwm-imx-tpm.c

-- 
2.7.4

[PATCH V12 1/5] dt-bindings: pwm: Add i.MX TPM PWM binding

[Anson Huang]

Add i.MX TPM(Low Power Timer/Pulse Width Modulation Module) PWM binding.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
No change.
---
 .../devicetree/bindings/pwm/imx-tpm-pwm.txt        | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt

diff --git a/Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt
new file mode 100644
index 0000000..3ba958d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt
@@ -0,0 +1,22 @@
+Freescale i.MX TPM PWM controller
+
+Required properties:
+- compatible : Should be "fsl,imx7ulp-pwm".
+- reg: Physical base address and length of the controller's registers.
+- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format.
+- clocks : The clock provided by the SoC to drive the PWM.
+- interrupts: The interrupt for the PWM controller.
+
+Note: The TPM counter and period counter are shared between multiple channels, so all channels
+should use same period setting.
+
+Example:
+
+tpm4: pwm@40250000 {
+	compatible = "fsl,imx7ulp-pwm";
+	reg = <0x40250000 0x1000>;
+	assigned-clocks = <&pcc2 IMX7ULP_CLK_LPTPM4>;
+	assigned-clock-parents = <&scg1 IMX7ULP_CLK_SOSC_BUS_CLK>;
+	clocks = <&pcc2 IMX7ULP_CLK_LPTPM4>;
+	#pwm-cells = <3>;
+};
-- 
2.7.4

[PATCH V12 2/5] pwm: Add i.MX TPM PWM driver support

[Anson Huang]

i.MX7ULP has TPM(Low Power Timer/Pulse Width Modulation Module)
inside, it can support multiple PWM channels, all the channels
share same counter and period setting, but each channel can
configure its duty and polarity independently.

There are several TPM modules in i.MX7ULP, the number of channels
in TPM modules are different, it can be read from each TPM module's
PARAM register.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
---
Changes since V11:
	- ONLY add function comment to pwm_imx_tpm_round_state(), no code change.
---
 drivers/pwm/Kconfig       |  11 ++
 drivers/pwm/Makefile      |   1 +
 drivers/pwm/pwm-imx-tpm.c | 448 ++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 460 insertions(+)
 create mode 100644 drivers/pwm/pwm-imx-tpm.c

diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index c054bd1..1311b540 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -210,6 +210,17 @@ config PWM_IMX27
 	  To compile this driver as a module, choose M here: the module
 	  will be called pwm-imx27.
 
+config PWM_IMX_TPM
+	tristate "i.MX TPM PWM support"
+	depends on ARCH_MXC || COMPILE_TEST
+	depends on HAVE_CLK && HAS_IOMEM
+	help
+	  Generic PWM framework driver for i.MX7ULP TPM module, TPM's full
+	  name is Low Power Timer/Pulse Width Modulation Module.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called pwm-imx-tpm.
+
 config PWM_JZ4740
 	tristate "Ingenic JZ47xx PWM support"
 	depends on MACH_INGENIC
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index 448825e..c368599 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_PWM_HIBVT)		+= pwm-hibvt.o
 obj-$(CONFIG_PWM_IMG)		+= pwm-img.o
 obj-$(CONFIG_PWM_IMX1)		+= pwm-imx1.o
 obj-$(CONFIG_PWM_IMX27)		+= pwm-imx27.o
+obj-$(CONFIG_PWM_IMX_TPM)	+= pwm-imx-tpm.o
 obj-$(CONFIG_PWM_JZ4740)	+= pwm-jz4740.o
 obj-$(CONFIG_PWM_LP3943)	+= pwm-lp3943.o
 obj-$(CONFIG_PWM_LPC18XX_SCT)	+= pwm-lpc18xx-sct.o
diff --git a/drivers/pwm/pwm-imx-tpm.c b/drivers/pwm/pwm-imx-tpm.c
new file mode 100644
index 0000000..62f1ec2
--- /dev/null
+++ b/drivers/pwm/pwm-imx-tpm.c
@@ -0,0 +1,448 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2018-2019 NXP.
+ *
+ * Limitations:
+ * - The TPM counter and period counter are shared between
+ *   multiple channels, so all channels should use same period
+ *   settings.
+ * - Changes to polarity cannot be latched at the time of the
+ *   next period start.
+ * - Changing period and duty cycle together isn't atomic,
+ *   with the wrong timing it might happen that a period is
+ *   produced with old duty cycle but new period settings.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/log2.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+#include <linux/slab.h>
+
+#define PWM_IMX_TPM_PARAM	0x4
+#define PWM_IMX_TPM_GLOBAL	0x8
+#define PWM_IMX_TPM_SC		0x10
+#define PWM_IMX_TPM_CNT		0x14
+#define PWM_IMX_TPM_MOD		0x18
+#define PWM_IMX_TPM_CnSC(n)	(0x20 + (n) * 0x8)
+#define PWM_IMX_TPM_CnV(n)	(0x24 + (n) * 0x8)
+
+#define PWM_IMX_TPM_PARAM_CHAN			GENMASK(7, 0)
+
+#define PWM_IMX_TPM_SC_PS			GENMASK(2, 0)
+#define PWM_IMX_TPM_SC_CMOD			GENMASK(4, 3)
+#define PWM_IMX_TPM_SC_CMOD_INC_EVERY_CLK	FIELD_PREP(PWM_IMX_TPM_SC_CMOD, 1)
+#define PWM_IMX_TPM_SC_CPWMS			BIT(5)
+
+#define PWM_IMX_TPM_CnSC_CHF	BIT(7)
+#define PWM_IMX_TPM_CnSC_MSB	BIT(5)
+#define PWM_IMX_TPM_CnSC_MSA	BIT(4)
+
+/*
+ * The reference manual describes this field as two separate bits. The
+ * semantic of the two bits isn't orthogonal though, so they are treated
+ * together as a 2-bit field here.
+ */
+#define PWM_IMX_TPM_CnSC_ELS	GENMASK(3, 2)
+#define PWM_IMX_TPM_CnSC_ELS_INVERSED	FIELD_PREP(PWM_IMX_TPM_CnSC_ELS, 1)
+#define PWM_IMX_TPM_CnSC_ELS_NORMAL	FIELD_PREP(PWM_IMX_TPM_CnSC_ELS, 2)
+
+
+#define PWM_IMX_TPM_MOD_WIDTH	16
+#define PWM_IMX_TPM_MOD_MOD	GENMASK(PWM_IMX_TPM_MOD_WIDTH - 1, 0)
+
+struct imx_tpm_pwm_chip {
+	struct pwm_chip chip;
+	struct clk *clk;
+	void __iomem *base;
+	struct mutex lock;
+	u32 user_count;
+	u32 enable_count;
+	u32 real_period;
+};
+
+struct imx_tpm_pwm_param {
+	u8 prescale;
+	u32 mod;
+	u32 val;
+};
+
+static inline struct imx_tpm_pwm_chip *to_imx_tpm_pwm_chip(struct pwm_chip *chip)
+{
+	return container_of(chip, struct imx_tpm_pwm_chip, chip);
+}
+
+/*
+ * This function determines for a given pwm_state *state that a consumer
+ * might request the pwm_state *real_state that eventually is implemented
+ * by the hardware and the necessary register values (in *p) to achieve
+ * this.
+ */
+static int pwm_imx_tpm_round_state(struct pwm_chip *chip,
+				   struct imx_tpm_pwm_param *p,
+				   struct pwm_state *real_state,
+				   struct pwm_state *state)
+{
+	struct imx_tpm_pwm_chip *tpm = to_imx_tpm_pwm_chip(chip);
+	u32 rate, prescale, period_count, clock_unit;
+	u64 tmp;
+
+	rate = clk_get_rate(tpm->clk);
+	tmp = (u64)state->period * rate;
+	clock_unit = DIV_ROUND_CLOSEST_ULL(tmp, NSEC_PER_SEC);
+	if (clock_unit <= PWM_IMX_TPM_MOD_MOD)
+		prescale = 0;
+	else
+		prescale = ilog2(clock_unit) + 1 - PWM_IMX_TPM_MOD_WIDTH;
+
+	if ((!FIELD_FIT(PWM_IMX_TPM_SC_PS, prescale)))
+		return -ERANGE;
+	p->prescale = prescale;
+
+	period_count = (clock_unit + ((1 << prescale) >> 1)) >> prescale;
+	p->mod = period_count;
+
+	/* calculate real period HW can support */
+	tmp = (u64)period_count << prescale;
+	tmp *= NSEC_PER_SEC;
+	real_state->period = DIV_ROUND_CLOSEST_ULL(tmp, rate);
+
+	/*
+	 * if eventually the PWM output is inactive, either
+	 * duty cycle is 0 or status is disabled, need to
+	 * make sure the output pin is inactive.
+	 */
+	if (!state->enabled)
+		real_state->duty_cycle = 0;
+	else
+		real_state->duty_cycle = state->duty_cycle;
+
+	tmp = (u64)p->mod * real_state->duty_cycle;
+	p->val = DIV_ROUND_CLOSEST_ULL(tmp, real_state->period);
+
+	real_state->polarity = state->polarity;
+	real_state->enabled = state->enabled;
+
+	return 0;
+}
+
+static void pwm_imx_tpm_get_state(struct pwm_chip *chip,
+				  struct pwm_device *pwm,
+				  struct pwm_state *state)
+{
+	struct imx_tpm_pwm_chip *tpm = to_imx_tpm_pwm_chip(chip);
+	u32 rate, val, prescale;
+	u64 tmp;
+
+	/* get period */
+	state->period = tpm->real_period;
+
+	/* get duty cycle */
+	rate = clk_get_rate(tpm->clk);
+	val = readl(tpm->base + PWM_IMX_TPM_SC);
+	prescale = FIELD_GET(PWM_IMX_TPM_SC_PS, val);
+	tmp = readl(tpm->base + PWM_IMX_TPM_CnV(pwm->hwpwm));
+	tmp = (tmp << prescale) * NSEC_PER_SEC;
+	state->duty_cycle = DIV_ROUND_CLOSEST_ULL(tmp, rate);
+
+	/* get polarity */
+	val = readl(tpm->base + PWM_IMX_TPM_CnSC(pwm->hwpwm));
+	if ((val & PWM_IMX_TPM_CnSC_ELS) == PWM_IMX_TPM_CnSC_ELS_INVERSED)
+		state->polarity = PWM_POLARITY_INVERSED;
+	else
+		/*
+		 * Assume reserved values (2b00 and 2b11) to yield
+		 * normal polarity.
+		 */
+		state->polarity = PWM_POLARITY_NORMAL;
+
+	/* get channel status */
+	state->enabled = FIELD_GET(PWM_IMX_TPM_CnSC_ELS, val) ? true : false;
+}
+
+/* this function is supposed to be called with mutex hold */
+static int pwm_imx_tpm_apply_hw(struct pwm_chip *chip,
+				struct imx_tpm_pwm_param *p,
+				struct pwm_state *state,
+				struct pwm_device *pwm)
+{
+	struct imx_tpm_pwm_chip *tpm = to_imx_tpm_pwm_chip(chip);
+	bool period_update = false;
+	bool duty_update = false;
+	u32 val, cmod, cur_prescale;
+	unsigned long timeout;
+	struct pwm_state c;
+
+	if (state->period != tpm->real_period) {
+		/*
+		 * TPM counter is shared by multiple channels, so
+		 * prescale and period can NOT be modified when
+		 * there are multiple channels in use with different
+		 * period settings.
+		 */
+		if (tpm->user_count > 1)
+			return -EBUSY;
+
+		val = readl(tpm->base + PWM_IMX_TPM_SC);
+		cmod = FIELD_GET(PWM_IMX_TPM_SC_CMOD, val);
+		cur_prescale = FIELD_GET(PWM_IMX_TPM_SC_PS, val);
+		if (cmod && cur_prescale != p->prescale)
+			return -EBUSY;
+
+		/* set TPM counter prescale */
+		val &= ~PWM_IMX_TPM_SC_PS;
+		val |= FIELD_PREP(PWM_IMX_TPM_SC_PS, p->prescale);
+		writel(val, tpm->base + PWM_IMX_TPM_SC);
+
+		/*
+		 * set period count:
+		 * if the PWM is disabled (CMOD[1:0] = 2b00), then MOD register
+		 * is updated when MOD register is written.
+		 *
+		 * if the PWM is enabled (CMOD[1:0] ≠ 2b00), the period length
+		 * is latched into hardware when the next period starts.
+		 */
+		writel(p->mod, tpm->base + PWM_IMX_TPM_MOD);
+		tpm->real_period = state->period;
+		period_update = true;
+	}
+
+	pwm_imx_tpm_get_state(chip, pwm, &c);
+
+	/* polarity is NOT allowed to be changed if PWM is active */
+	if (c.enabled && c.polarity != state->polarity)
+		return -EBUSY;
+
+	if (state->duty_cycle != c.duty_cycle) {
+		/*
+		 * set channel value:
+		 * if the PWM is disabled (CMOD[1:0] = 2b00), then CnV register
+		 * is updated when CnV register is written.
+		 *
+		 * if the PWM is enabled (CMOD[1:0] ≠ 2b00), the duty length
+		 * is latched into hardware when the next period starts.
+		 */
+		writel(p->val, tpm->base + PWM_IMX_TPM_CnV(pwm->hwpwm));
+		duty_update = true;
+	}
+
+	/* make sure MOD & CnV registers are updated */
+	if (period_update || duty_update) {
+		timeout = jiffies + msecs_to_jiffies(tpm->real_period /
+						     NSEC_PER_MSEC + 1);
+		while (readl(tpm->base + PWM_IMX_TPM_MOD) != p->mod
+		       || readl(tpm->base + PWM_IMX_TPM_CnV(pwm->hwpwm))
+		       != p->val) {
+			if (time_after(jiffies, timeout))
+				return -ETIME;
+			cpu_relax();
+		}
+	}
+
+	/*
+	 * polarity settings will enabled/disable output status
+	 * immediately, so if the channel is disabled, need to
+	 * make sure MSA/MSB/ELS are set to 0 which means channel
+	 * disabled.
+	 */
+	val = readl(tpm->base + PWM_IMX_TPM_CnSC(pwm->hwpwm));
+	val &= ~(PWM_IMX_TPM_CnSC_ELS | PWM_IMX_TPM_CnSC_MSA |
+		 PWM_IMX_TPM_CnSC_MSB);
+	if (state->enabled) {
+		/*
+		 * set polarity (for edge-aligned PWM modes)
+		 *
+		 * ELS[1:0] = 2b10 yields normal polarity behaviour,
+		 * ELS[1:0] = 2b01 yields inversed polarity.
+		 * The other values are reserved.
+		 */
+		val |= PWM_IMX_TPM_CnSC_MSB;
+		val |= (state->polarity == PWM_POLARITY_NORMAL) ?
+			PWM_IMX_TPM_CnSC_ELS_NORMAL :
+			PWM_IMX_TPM_CnSC_ELS_INVERSED;
+	}
+	writel(val, tpm->base + PWM_IMX_TPM_CnSC(pwm->hwpwm));
+
+	/* control the counter status */
+	if (state->enabled != c.enabled) {
+		val = readl(tpm->base + PWM_IMX_TPM_SC);
+		if (state->enabled) {
+			if (++tpm->enable_count == 1)
+				val |= PWM_IMX_TPM_SC_CMOD_INC_EVERY_CLK;
+		} else {
+			if (--tpm->enable_count == 0)
+				val &= ~PWM_IMX_TPM_SC_CMOD;
+		}
+		writel(val, tpm->base + PWM_IMX_TPM_SC);
+	}
+
+	return 0;
+}
+
+static int pwm_imx_tpm_apply(struct pwm_chip *chip,
+			     struct pwm_device *pwm,
+			     struct pwm_state *state)
+{
+	struct imx_tpm_pwm_chip *tpm = to_imx_tpm_pwm_chip(chip);
+	struct imx_tpm_pwm_param param;
+	struct pwm_state real_state;
+	int ret;
+
+	ret = pwm_imx_tpm_round_state(chip, &param, &real_state, state);
+	if (ret)
+		return ret;
+
+	mutex_lock(&tpm->lock);
+	ret = pwm_imx_tpm_apply_hw(chip, &param, &real_state, pwm);
+	mutex_unlock(&tpm->lock);
+
+	return ret;
+}
+
+static int pwm_imx_tpm_request(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+	struct imx_tpm_pwm_chip *tpm = to_imx_tpm_pwm_chip(chip);
+
+	mutex_lock(&tpm->lock);
+	tpm->user_count++;
+	mutex_unlock(&tpm->lock);
+
+	return 0;
+}
+
+static void pwm_imx_tpm_free(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+	struct imx_tpm_pwm_chip *tpm = to_imx_tpm_pwm_chip(chip);
+
+	mutex_lock(&tpm->lock);
+	tpm->user_count--;
+	mutex_unlock(&tpm->lock);
+}
+
+static const struct pwm_ops imx_tpm_pwm_ops = {
+	.request = pwm_imx_tpm_request,
+	.free = pwm_imx_tpm_free,
+	.get_state = pwm_imx_tpm_get_state,
+	.apply = pwm_imx_tpm_apply,
+	.owner = THIS_MODULE,
+};
+
+static int pwm_imx_tpm_probe(struct platform_device *pdev)
+{
+	struct imx_tpm_pwm_chip *tpm;
+	int ret;
+	u32 val;
+
+	tpm = devm_kzalloc(&pdev->dev, sizeof(*tpm), GFP_KERNEL);
+	if (!tpm)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, tpm);
+
+	tpm->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(tpm->base))
+		return PTR_ERR(tpm->base);
+
+	tpm->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(tpm->clk)) {
+		ret = PTR_ERR(tpm->clk);
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev,
+				"failed to get PWM clock: %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(tpm->clk);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"failed to prepare or enable clock: %d\n", ret);
+		return ret;
+	}
+
+	tpm->chip.dev = &pdev->dev;
+	tpm->chip.ops = &imx_tpm_pwm_ops;
+	tpm->chip.base = -1;
+	tpm->chip.of_xlate = of_pwm_xlate_with_flags;
+	tpm->chip.of_pwm_n_cells = 3;
+
+	/* get number of channels */
+	val = readl(tpm->base + PWM_IMX_TPM_PARAM);
+	tpm->chip.npwm = FIELD_GET(PWM_IMX_TPM_PARAM_CHAN, val);
+
+	mutex_init(&tpm->lock);
+
+	ret = pwmchip_add(&tpm->chip);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to add PWM chip: %d\n", ret);
+		clk_disable_unprepare(tpm->clk);
+	}
+
+	return ret;
+}
+
+static int pwm_imx_tpm_remove(struct platform_device *pdev)
+{
+	struct imx_tpm_pwm_chip *tpm = platform_get_drvdata(pdev);
+	int ret = pwmchip_remove(&tpm->chip);
+
+	clk_disable_unprepare(tpm->clk);
+
+	return ret;
+}
+
+static int __maybe_unused pwm_imx_tpm_suspend(struct device *dev)
+{
+	struct imx_tpm_pwm_chip *tpm = dev_get_drvdata(dev);
+
+	if (tpm->enable_count > 0)
+		return -EBUSY;
+
+	clk_disable_unprepare(tpm->clk);
+
+	return 0;
+}
+
+static int __maybe_unused pwm_imx_tpm_resume(struct device *dev)
+{
+	struct imx_tpm_pwm_chip *tpm = dev_get_drvdata(dev);
+	int ret = 0;
+
+	ret = clk_prepare_enable(tpm->clk);
+	if (ret)
+		dev_err(dev,
+			"failed to prepare or enable clock: %d\n",
+			ret);
+
+	return ret;
+}
+
+static SIMPLE_DEV_PM_OPS(imx_tpm_pwm_pm,
+			 pwm_imx_tpm_suspend, pwm_imx_tpm_resume);
+
+static const struct of_device_id imx_tpm_pwm_dt_ids[] = {
+	{ .compatible = "fsl,imx7ulp-pwm", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx_tpm_pwm_dt_ids);
+
+static struct platform_driver imx_tpm_pwm_driver = {
+	.driver = {
+		.name = "imx7ulp-tpm-pwm",
+		.of_match_table = imx_tpm_pwm_dt_ids,
+		.pm = &imx_tpm_pwm_pm,
+	},
+	.probe	= pwm_imx_tpm_probe,
+	.remove = pwm_imx_tpm_remove,
+};
+module_platform_driver(imx_tpm_pwm_driver);
+
+MODULE_AUTHOR("Anson Huang <Anson.Huang@nxp.com>");
+MODULE_DESCRIPTION("i.MX TPM PWM Driver");
+MODULE_LICENSE("GPL v2");
-- 
2.7.4

[PATCH V12 3/5] ARM: imx_v6_v7_defconfig: Add TPM PWM support by default

[Anson Huang]

Select CONFIG_PWM_IMX_TPM by default to support i.MX7ULP
TPM PWM.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
No change.
---
 arch/arm/configs/imx_v6_v7_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index ea387cb..cee7c61 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -402,6 +402,7 @@ CONFIG_MPL3115=y
 CONFIG_PWM=y
 CONFIG_PWM_FSL_FTM=y
 CONFIG_PWM_IMX27=y
+CONFIG_PWM_IMX_TPM=y
 CONFIG_NVMEM_IMX_OCOTP=y
 CONFIG_NVMEM_VF610_OCOTP=y
 CONFIG_TEE=y
-- 
2.7.4

[PATCH V12 4/5] ARM: dts: imx7ulp: Add tpm pwm support

[Anson Huang]

Add i.MX7ULP EVK board PWM support.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
No change.
---
 arch/arm/boot/dts/imx7ulp.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/imx7ulp.dtsi b/arch/arm/boot/dts/imx7ulp.dtsi
index d6b7110..8fb9559 100644
--- a/arch/arm/boot/dts/imx7ulp.dtsi
+++ b/arch/arm/boot/dts/imx7ulp.dtsi
@@ -124,6 +124,16 @@
 			status = "disabled";
 		};
 
+		tpm4: pwm@40250000 {
+			compatible = "fsl,imx7ulp-pwm";
+			reg = <0x40250000 0x1000>;
+			assigned-clocks = <&pcc2 IMX7ULP_CLK_LPTPM4>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_SOSC_BUS_CLK>;
+			clocks = <&pcc2 IMX7ULP_CLK_LPTPM4>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		tpm5: tpm@40260000 {
 			compatible = "fsl,imx7ulp-tpm";
 			reg = <0x40260000 0x1000>;
-- 
2.7.4

[PATCH V12 5/5] ARM: dts: imx7ulp-evk: Add backlight support

[Anson Huang]

This patch adds i.MX7ULP EVK board MIPI-DSI backlight support.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
No change.
---
 arch/arm/boot/dts/imx7ulp-evk.dts | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/imx7ulp-evk.dts b/arch/arm/boot/dts/imx7ulp-evk.dts
index a09026a..59f094e 100644
--- a/arch/arm/boot/dts/imx7ulp-evk.dts
+++ b/arch/arm/boot/dts/imx7ulp-evk.dts
@@ -22,6 +22,14 @@
 		reg = <0x60000000 0x40000000>;
 	};
 
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&tpm4 1 50000 0>;
+		brightness-levels = <0 20 25 30 35 40 100>;
+		default-brightness-level = <6>;
+		status = "okay";
+	};
+
 	reg_vsd_3v3: regulator-vsd-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "VSD_3V3";
@@ -40,6 +48,12 @@
 	status = "okay";
 };
 
+&tpm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0>;
+	status = "okay";
+};
+
 &usdhc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc0>;
@@ -57,6 +71,12 @@
 		bias-pull-up;
 	};
 
+	pinctrl_pwm0: pwm0grp {
+		fsl,pins = <
+			IMX7ULP_PAD_PTF2__TPM4_CH1	0x2
+		>;
+	};
+
 	pinctrl_usdhc0: usdhc0grp {
 		fsl,pins = <
 			IMX7ULP_PAD_PTD1__SDHC0_CMD	0x43
-- 
2.7.4

Re: [PATCH V12 1/5] dt-bindings: pwm: Add i.MX TPM PWM binding

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 496 bytes --]

On Thu, May 09, 2019 at 01:29:19PM +0000, Anson Huang wrote:
> Add i.MX TPM(Low Power Timer/Pulse Width Modulation Module) PWM binding.
> 
> Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> No change.
> ---
>  .../devicetree/bindings/pwm/imx-tpm-pwm.txt        | 22 ++++++++++++++++++++++
>  1 file changed, 22 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt

Applied, thanks.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH V12 2/5] pwm: Add i.MX TPM PWM driver support

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 987 bytes --]

On Thu, May 09, 2019 at 01:29:29PM +0000, Anson Huang wrote:
> i.MX7ULP has TPM(Low Power Timer/Pulse Width Modulation Module)
> inside, it can support multiple PWM channels, all the channels
> share same counter and period setting, but each channel can
> configure its duty and polarity independently.
> 
> There are several TPM modules in i.MX7ULP, the number of channels
> in TPM modules are different, it can be read from each TPM module's
> PARAM register.
> 
> Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> ---
> Changes since V11:
> 	- ONLY add function comment to pwm_imx_tpm_round_state(), no code change.
> ---
>  drivers/pwm/Kconfig       |  11 ++
>  drivers/pwm/Makefile      |   1 +
>  drivers/pwm/pwm-imx-tpm.c | 448 ++++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 460 insertions(+)
>  create mode 100644 drivers/pwm/pwm-imx-tpm.c

Applied, thanks.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]