* [PATCH v2 1/2] arm: dts: imx*(colibri|apalis): add missing recovery modes to i2c
@ 2019-10-16 17:03 Philippe Schenker
2019-10-16 17:03 ` [PATCH v2 2/2] arm: dts: vf-colibri: add recovery mode " Philippe Schenker
2019-10-28 3:08 ` [PATCH v2 1/2] arm: dts: imx*(colibri|apalis): add missing recovery modes " Shawn Guo
0 siblings, 2 replies; 3+ messages in thread
From: Philippe Schenker @ 2019-10-16 17:03 UTC (permalink / raw)
To: devicetree, Shawn Guo
Cc: Marcel Ziswiler, Max Krummenacher, Stefan Agner, linux-kernel,
Luka Pivk, Philippe Schenker, Fabio Estevam, Rob Herring,
linux-arm-kernel, Pengutronix Kernel Team, Mark Rutland,
NXP Linux Team, Sascha Hauer
This patch adds missing i2c recovery modes and corrects wrongly named
ones.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
---
Changes in v2:
- Added scl/sda gpio
- Added missing recovery mode to i2c2 on imx6qdl-colibri
arch/arm/boot/dts/imx6qdl-apalis.dtsi | 30 +++++++++++++++++++++-----
arch/arm/boot/dts/imx6qdl-colibri.dtsi | 18 ++++++++++++----
2 files changed, 39 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
index 7c4ad541c3f5..86cad6c9f0f9 100644
--- a/arch/arm/boot/dts/imx6qdl-apalis.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
@@ -205,8 +205,11 @@
/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
&i2c1 {
clock-frequency = <100000>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
};
@@ -216,8 +219,11 @@
*/
&i2c2 {
clock-frequency = <100000>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
pmic: pfuze100@8 {
@@ -372,9 +378,9 @@
*/
&i2c3 {
clock-frequency = <100000>;
- pinctrl-names = "default", "recovery";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c3>;
- pinctrl-1 = <&pinctrl_i2c3_recovery>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
scl-gpios = <&gpio3 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio3 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
@@ -646,6 +652,13 @@
>;
};
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x4001b8b1
+ >;
+ };
+
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
@@ -653,6 +666,13 @@
>;
};
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x4001b8b1
+ >;
+ };
+
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
@@ -660,7 +680,7 @@
>;
};
- pinctrl_i2c3_recovery: i2c3recoverygrp {
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
fsl,pins = <
MX6QDL_PAD_EIM_D17__GPIO3_IO17 0x4001b8b1
MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x4001b8b1
diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index 019dda6b88ad..8ab9960fc15d 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -166,8 +166,11 @@
*/
&i2c2 {
clock-frequency = <100000>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-0 = <&pinctrl_i2c2_gpio>;
+ scl-gpios = <&gpio2 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio3 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
pmic: pfuze100@8 {
@@ -312,9 +315,9 @@
*/
&i2c3 {
clock-frequency = <100000>;
- pinctrl-names = "default", "recovery";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c3>;
- pinctrl-1 = <&pinctrl_i2c3_recovery>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
@@ -509,6 +512,13 @@
>;
};
+ pinctrl_i2c2_gpio: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x4001b8b1
+ MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x4001b8b1
+ >;
+ };
+
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
@@ -516,7 +526,7 @@
>;
};
- pinctrl_i2c3_recovery: i2c3recoverygrp {
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
fsl,pins = <
MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x4001b8b1
MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x4001b8b1
--
2.23.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH v2 2/2] arm: dts: vf-colibri: add recovery mode to i2c
2019-10-16 17:03 [PATCH v2 1/2] arm: dts: imx*(colibri|apalis): add missing recovery modes to i2c Philippe Schenker
@ 2019-10-16 17:03 ` Philippe Schenker
2019-10-28 3:08 ` [PATCH v2 1/2] arm: dts: imx*(colibri|apalis): add missing recovery modes " Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Philippe Schenker @ 2019-10-16 17:03 UTC (permalink / raw)
To: devicetree, Shawn Guo
Cc: Marcel Ziswiler, Max Krummenacher, Stefan Agner, linux-kernel,
Luka Pivk, Philippe Schenker, Stefan Agner, Rob Herring,
linux-arm-kernel, Pengutronix Kernel Team, Mark Rutland,
Sascha Hauer
This patch enables the recovery mode now available.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
---
Changes in v2:
- Added scl/sda gpios
arch/arm/boot/dts/vf-colibri.dtsi | 12 +++++++++++-
1 file changed, 11 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/vf-colibri.dtsi
index b6a1eeeb2bb4..fba37b8756f7 100644
--- a/arch/arm/boot/dts/vf-colibri.dtsi
+++ b/arch/arm/boot/dts/vf-colibri.dtsi
@@ -129,8 +129,11 @@
&i2c0 {
clock-frequency = <400000>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c0>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ scl-gpios = <&gpio1 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
};
&nfc {
@@ -308,6 +311,13 @@
>;
};
+ pinctrl_i2c0_gpio: i2c0gpiogrp {
+ fsl,pins = <
+ VF610_PAD_PTB14__GPIO_36 0x37ff
+ VF610_PAD_PTB15__GPIO_37 0x37ff
+ >;
+ };
+
pinctrl_nfc: nfcgrp {
fsl,pins = <
VF610_PAD_PTD23__NF_IO7 0x28df
--
2.23.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v2 1/2] arm: dts: imx*(colibri|apalis): add missing recovery modes to i2c
2019-10-16 17:03 [PATCH v2 1/2] arm: dts: imx*(colibri|apalis): add missing recovery modes to i2c Philippe Schenker
2019-10-16 17:03 ` [PATCH v2 2/2] arm: dts: vf-colibri: add recovery mode " Philippe Schenker
@ 2019-10-28 3:08 ` Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Shawn Guo @ 2019-10-28 3:08 UTC (permalink / raw)
To: Philippe Schenker
Cc: devicetree, Marcel Ziswiler, Max Krummenacher, Stefan Agner,
linux-kernel, Luka Pivk, Fabio Estevam, Rob Herring,
linux-arm-kernel, Pengutronix Kernel Team, Mark Rutland,
NXP Linux Team, Sascha Hauer
On Wed, Oct 16, 2019 at 05:03:41PM +0000, Philippe Schenker wrote:
> This patch adds missing i2c recovery modes and corrects wrongly named
> ones.
>
> Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
As a practise, we use 'ARM: ' to prefix i.MX arch/arm/ patches.
I fixed it up and applied both patches.
Shawn
>
> ---
>
> Changes in v2:
> - Added scl/sda gpio
> - Added missing recovery mode to i2c2 on imx6qdl-colibri
>
> arch/arm/boot/dts/imx6qdl-apalis.dtsi | 30 +++++++++++++++++++++-----
> arch/arm/boot/dts/imx6qdl-colibri.dtsi | 18 ++++++++++++----
> 2 files changed, 39 insertions(+), 9 deletions(-)
>
> diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
> index 7c4ad541c3f5..86cad6c9f0f9 100644
> --- a/arch/arm/boot/dts/imx6qdl-apalis.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
> @@ -205,8 +205,11 @@
> /* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
> &i2c1 {
> clock-frequency = <100000>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "gpio";
> pinctrl-0 = <&pinctrl_i2c1>;
> + pinctrl-1 = <&pinctrl_i2c1_gpio>;
> + scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> status = "disabled";
> };
>
> @@ -216,8 +219,11 @@
> */
> &i2c2 {
> clock-frequency = <100000>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "gpio";
> pinctrl-0 = <&pinctrl_i2c2>;
> + pinctrl-1 = <&pinctrl_i2c2_gpio>;
> + scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> status = "okay";
>
> pmic: pfuze100@8 {
> @@ -372,9 +378,9 @@
> */
> &i2c3 {
> clock-frequency = <100000>;
> - pinctrl-names = "default", "recovery";
> + pinctrl-names = "default", "gpio";
> pinctrl-0 = <&pinctrl_i2c3>;
> - pinctrl-1 = <&pinctrl_i2c3_recovery>;
> + pinctrl-1 = <&pinctrl_i2c3_gpio>;
> scl-gpios = <&gpio3 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> sda-gpios = <&gpio3 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> status = "disabled";
> @@ -646,6 +652,13 @@
> >;
> };
>
> + pinctrl_i2c1_gpio: i2c1gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x4001b8b1
> + MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x4001b8b1
> + >;
> + };
> +
> pinctrl_i2c2: i2c2grp {
> fsl,pins = <
> MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> @@ -653,6 +666,13 @@
> >;
> };
>
> + pinctrl_i2c2_gpio: i2c2gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x4001b8b1
> + >;
> + };
> +
> pinctrl_i2c3: i2c3grp {
> fsl,pins = <
> MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
> @@ -660,7 +680,7 @@
> >;
> };
>
> - pinctrl_i2c3_recovery: i2c3recoverygrp {
> + pinctrl_i2c3_gpio: i2c3gpiogrp {
> fsl,pins = <
> MX6QDL_PAD_EIM_D17__GPIO3_IO17 0x4001b8b1
> MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x4001b8b1
> diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
> index 019dda6b88ad..8ab9960fc15d 100644
> --- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
> @@ -166,8 +166,11 @@
> */
> &i2c2 {
> clock-frequency = <100000>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "gpio";
> pinctrl-0 = <&pinctrl_i2c2>;
> + pinctrl-0 = <&pinctrl_i2c2_gpio>;
> + scl-gpios = <&gpio2 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio3 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> status = "okay";
>
> pmic: pfuze100@8 {
> @@ -312,9 +315,9 @@
> */
> &i2c3 {
> clock-frequency = <100000>;
> - pinctrl-names = "default", "recovery";
> + pinctrl-names = "default", "gpio";
> pinctrl-0 = <&pinctrl_i2c3>;
> - pinctrl-1 = <&pinctrl_i2c3_recovery>;
> + pinctrl-1 = <&pinctrl_i2c3_gpio>;
> scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> status = "disabled";
> @@ -509,6 +512,13 @@
> >;
> };
>
> + pinctrl_i2c2_gpio: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x4001b8b1
> + MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x4001b8b1
> + >;
> + };
> +
> pinctrl_i2c3: i2c3grp {
> fsl,pins = <
> MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
> @@ -516,7 +526,7 @@
> >;
> };
>
> - pinctrl_i2c3_recovery: i2c3recoverygrp {
> + pinctrl_i2c3_gpio: i2c3gpiogrp {
> fsl,pins = <
> MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x4001b8b1
> MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x4001b8b1
> --
> 2.23.0
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-10-28 3:08 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-16 17:03 [PATCH v2 1/2] arm: dts: imx*(colibri|apalis): add missing recovery modes to i2c Philippe Schenker
2019-10-16 17:03 ` [PATCH v2 2/2] arm: dts: vf-colibri: add recovery mode " Philippe Schenker
2019-10-28 3:08 ` [PATCH v2 1/2] arm: dts: imx*(colibri|apalis): add missing recovery modes " Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).