* [PATCH v2 0/5] mainline Protonic boards
@ 2020-03-19 5:56 Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 1/5] dt-bindings: vendor-prefixes: Add an entry for Protonic Holland Oleksij Rempel
` (4 more replies)
0 siblings, 5 replies; 8+ messages in thread
From: Oleksij Rempel @ 2020-03-19 5:56 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team
changes v2:
- squash PRTI6Q patches
Oleksij Rempel (5):
dt-bindings: vendor-prefixes: Add an entry for Protonic Holland
ARM: dts: add Protonic PRTI6Q board
ARM: dts: add Protonic WD2 board
ARM: dts: add Protonic VT7 board
ARM: dts: add Protonic RVT board
.../devicetree/bindings/arm/fsl.yaml | 4 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/imx6dl-prtrvt.dts | 108 ++++
arch/arm/boot/dts/imx6dl-prtvt7.dts | 390 ++++++++++++++
arch/arm/boot/dts/imx6q-prti6q.dts | 286 ++++++++++
arch/arm/boot/dts/imx6q-prtwd2.dts | 242 +++++++++
arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 489 ++++++++++++++++++
8 files changed, 1525 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
create mode 100644 arch/arm/boot/dts/imx6q-prtwd2.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
--
2.25.1
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2 1/5] dt-bindings: vendor-prefixes: Add an entry for Protonic Holland
2020-03-19 5:56 [PATCH v2 0/5] mainline Protonic boards Oleksij Rempel
@ 2020-03-19 5:56 ` Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 2/5] ARM: dts: add Protonic PRTI6Q board Oleksij Rempel
` (3 subsequent siblings)
4 siblings, 0 replies; 8+ messages in thread
From: Oleksij Rempel @ 2020-03-19 5:56 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team
Add "prt" entry for Protonic Holland: https://www.protonic.nl/en/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 9e67944bec9c..a0d3214187a5 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -775,6 +775,8 @@ patternProperties:
description: Primux Trading, S.L.
"^probox2,.*":
description: PROBOX2 (by W2COMP Co., Ltd.)
+ "^prt,.*":
+ description: Protonic Holland
"^pulsedlight,.*":
description: PulsedLight, Inc
"^purism,.*":
--
2.25.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 2/5] ARM: dts: add Protonic PRTI6Q board
2020-03-19 5:56 [PATCH v2 0/5] mainline Protonic boards Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 1/5] dt-bindings: vendor-prefixes: Add an entry for Protonic Holland Oleksij Rempel
@ 2020-03-19 5:56 ` Oleksij Rempel
2020-03-19 10:21 ` Marco Felsch
2020-03-19 5:56 ` [PATCH v2 3/5] ARM: dts: add Protonic WD2 board Oleksij Rempel
` (2 subsequent siblings)
4 siblings, 1 reply; 8+ messages in thread
From: Oleksij Rempel @ 2020-03-19 5:56 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, David Jander, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team
Protonic PRTI6Q is a development board and a base class for different
specific customer application boards based on the i.MX6 family of SoCs,
developed by Protonic Holland.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/arm/fsl.yaml | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-prti6q.dts | 286 ++++++++++
arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 489 ++++++++++++++++++
4 files changed, 777 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index a8e0b4a813ed..3b52b582efdf 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -119,6 +119,7 @@ properties:
- fsl,imx6q-sabreauto
- fsl,imx6q-sabrelite
- fsl,imx6q-sabresd
+ - prt,prti6q # Protonic PRTI6Q board
- technologic,imx6q-ts4900
- technologic,imx6q-ts7970
- toradex,apalis_imx6q # Apalis iMX6 Module
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d6546d2676b9..3f500a9e88a9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -530,6 +530,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-phytec-mira-rdk-nand.dtb \
imx6q-phytec-pbab01.dtb \
imx6q-pistachio.dtb \
+ imx6q-prti6q.dtb \
imx6q-rex-pro.dtb \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
diff --git a/arch/arm/boot/dts/imx6q-prti6q.dts b/arch/arm/boot/dts/imx6q-prti6q.dts
new file mode 100644
index 000000000000..8880d56c59ac
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-prti6q.dts
@@ -0,0 +1,286 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+
+/ {
+ model = "Protonic PRTI6Q board";
+ compatible = "prt,prti6q", "fsl,imx6q";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0xf0000000>;
+ };
+
+ sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "imx-spdif";
+ spdif-controller = <&spdif>;
+ spdif-in;
+ spdif-out;
+ };
+
+ clocks {
+ spi3_crystal: spi3clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ reg_wl12xx: regulator-wl12xx {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wl1271_npd>;
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-WL12xx";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio1 26 0>;
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+
+ can3: mcp2515@0 {
+ compatible = "microchip,mcp2515";
+ spi-max-frequency = <5000000>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+ reg = <0>;
+ clocks = <&spi3_crystal>;
+ };
+
+ adc128: adc128@1 {
+ compatible = "ti,adc128s052";
+ reg = <1>;
+ vref-supply = <®_3v3>;
+ spi-max-frequency = <2000000>;
+ };
+};
+
+&iomuxc {
+ prti6q {
+ pinctrl_nand: nandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0
+ >;
+ };
+
+ pinctrl_hdmi: hdmigrp {
+ fsl,pins = <
+ /* NOTE: DDC is done via I2C2, so DON'T
+ * configure DDC pins for HDMI!
+ */
+ MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_spdif: spdifgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
+ MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
+ MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
+ >;
+ };
+
+ /* DDC */
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ /* CAN3 CS */
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ /* ADC128S022 CS */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
+ /* CAN3_nINT */
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ /* WL12xx IRQ */
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
+ >;
+ };
+
+ pinctrl_wl1271_npd: wl1271_npd {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
+ >;
+ };
+ };
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spdif>;
+ status = "okay";
+};
+
+/* DDC */
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ vmmc-supply = <®_wl12xx>;
+ non-removable;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ status = "okay";
+
+ wl1271 {
+ compatible = "ti,wl1271";
+ irq-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ ref-clock-frequency = "38400000";
+ tcxo-clock-frequency = "19200000";
+ };
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
new file mode 100644
index 000000000000..6515b96fa0a5
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
@@ -0,0 +1,489 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_1v2: regulator-1v2 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "otg-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 0>;
+ enable-active-high;
+ };
+
+ reg_usb_h1_vbus: regulator-h1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "h1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&codec>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+
+ backlight_lcd: backlight-lcd {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 1 2 4 6 8 12 16 24 32 48 64 96 128 192
+ 255>;
+ default-brightness-level = <15>;
+ power-supply = <®_3v3>;
+ status = "okay";
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds: led-controller {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-hb0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-mmc0 {
+ function = LED_FUNCTION_SD;
+ gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "disk-activity";
+ };
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux_ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux_pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash: s25sl032p@0 {
+ compatible = "spansion,m25p80";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x0 0x80000>;
+ };
+
+ partition@80000 {
+ label = "env";
+ reg = <0x80000 0x10000>;
+ };
+
+ partition@90000 {
+ label = "spare";
+ reg = <0x90000 0x370000>;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ codec: sgtl5000@a {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ can_adc: ads1015@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+
+ tmp103: tmp103@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ prti6q {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x100b0
+ MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x100b0
+ MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b0
+ MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1b0b0
+ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1b0b0
+ >;
+ };
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ /* CAN3_nINT */
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__SD1_CD_B 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ >;
+ };
+
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_backlight: backlightgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1csi0grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+ >;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&ssi1 {
+ #sound-dai-cells = <0>;
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #size-cells = <1>;
+ #address-cells = <1>;
+
+ bootstate_backend: bootstate_backend@f0000 {
+ reg = <0xf0000 0x10000>;
+ label = "bootstate";
+ };
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ status = "okay";
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 3/5] ARM: dts: add Protonic WD2 board
2020-03-19 5:56 [PATCH v2 0/5] mainline Protonic boards Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 1/5] dt-bindings: vendor-prefixes: Add an entry for Protonic Holland Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 2/5] ARM: dts: add Protonic PRTI6Q board Oleksij Rempel
@ 2020-03-19 5:56 ` Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 4/5] ARM: dts: add Protonic VT7 board Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 5/5] ARM: dts: add Protonic RVT board Oleksij Rempel
4 siblings, 0 replies; 8+ messages in thread
From: Oleksij Rempel @ 2020-03-19 5:56 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, David Jander, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team
Add support for the Protonic WD2 board, which is an internal development
platform for low-cost agricultural Virtual Terminals based on COTS tablets
and web applications.
It inherits from the PRTI6Q base class.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/arm/fsl.yaml | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-prtwd2.dts | 242 ++++++++++++++++++
3 files changed, 244 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-prtwd2.dts
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 3b52b582efdf..5bdf8d38b2f0 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -120,6 +120,7 @@ properties:
- fsl,imx6q-sabrelite
- fsl,imx6q-sabresd
- prt,prti6q # Protonic PRTI6Q board
+ - prt,prtwd2 # Protonic WD2 board
- technologic,imx6q-ts4900
- technologic,imx6q-ts7970
- toradex,apalis_imx6q # Apalis iMX6 Module
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3f500a9e88a9..b6fc2b375a61 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -531,6 +531,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-phytec-pbab01.dtb \
imx6q-pistachio.dtb \
imx6q-prti6q.dtb \
+ imx6q-prtwd2.dtb \
imx6q-rex-pro.dtb \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
diff --git a/arch/arm/boot/dts/imx6q-prtwd2.dts b/arch/arm/boot/dts/imx6q-prtwd2.dts
new file mode 100644
index 000000000000..275c291d1ef4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-prtwd2.dts
@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2018 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+
+/ {
+ model = "Protonic WD2 board";
+ compatible = "prt,prtwd2", "fsl,imx6q";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ usdhc2_pwrseq: usdhc2_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wlan_npd>;
+ reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
+ };
+
+ /* PRTWD2 rev 1 bitbang I2C for Ethernet Switch */
+ i2c@4 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio1 22 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH)>;
+ i2c-gpio,delay-us = <20>; /* ~10 kHz */
+ i2c-gpio,scl-output-only;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+&iomuxc {
+ prti6q {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x130b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+ >;
+ };
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ /* CAN1_SR + CAN2_SR GPIO outputs */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+
+ /* HW revision detect */
+ /* REV_ID0 */
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
+ /* REV_ID1 */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ /* REV_ID2 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ /* REV_ID3 */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
+ /* REV_ID4 */
+ MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
+
+ /* USB charging control */
+ MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x130b0
+ MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x130b0
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x130b0
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x130b0
+
+ MX6QDL_PAD_ENET_MDIO__GPIO1_IO22 0x1f8b0
+ MX6QDL_PAD_ENET_MDC__GPIO1_IO31 0x1f8b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ /* DEBUG0 */
+ MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
+ /* DEBUG1 */
+ MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
+ /* POWER_LED */
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
+ >;
+ };
+
+ pinctrl_wlan_npd: wlan_npd {
+ fsl,pins = <
+ /* WL_REG_ON */
+ MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+
+ fixedphy: fixed-link {
+ speed = <100>;
+ pause;
+ full-duplex;
+ };
+};
+
+&ecspi1 {
+ status = "disabled";
+};
+
+&flash {
+ status = "disabled";
+};
+
+&ecspi1 {
+ status = "disabled";
+};
+
+&audmux {
+ status = "disabled";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&pcie {
+ status = "disabled";
+};
+
+&pwm1 {
+ status = "disabled";
+};
+
+&ssi1 {
+ status = "disabled";
+};
+
+&uart2 {
+ status = "disabled";
+};
+
+&uart5 {
+ status = "disabled";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ no-1-8-v;
+ non-removable;
+ mmc-pwrseq = <&usdhc2_pwrseq>;
+ pm-ignore-notify;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+&can2 {
+ status = "disabled";
+};
+
+&can_adc {
+ channel@4 {
+ reg = <4>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ channel@6 {
+ reg = <6>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ channel@7 {
+ reg = <7>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 4/5] ARM: dts: add Protonic VT7 board
2020-03-19 5:56 [PATCH v2 0/5] mainline Protonic boards Oleksij Rempel
` (2 preceding siblings ...)
2020-03-19 5:56 ` [PATCH v2 3/5] ARM: dts: add Protonic WD2 board Oleksij Rempel
@ 2020-03-19 5:56 ` Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 5/5] ARM: dts: add Protonic RVT board Oleksij Rempel
4 siblings, 0 replies; 8+ messages in thread
From: Oleksij Rempel @ 2020-03-19 5:56 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, Robin van der Gracht, David Jander, devicetree,
Fabio Estevam, linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team
The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch
touchscreen display.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/arm/fsl.yaml | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-prtvt7.dts | 390 ++++++++++++++++++
3 files changed, 392 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 5bdf8d38b2f0..424be1edf005 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -168,6 +168,7 @@ properties:
- emtrion,emcon-mx6-avari # emCON-MX6S or emCON-MX6DL SoM on Avari Base
- fsl,imx6dl-sabreauto # i.MX6 DualLite/Solo SABRE Automotive Board
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
+ - prt,prtvt7 # Protonic VT7 board
- technologic,imx6dl-ts4900
- technologic,imx6dl-ts7970
- toradex,colibri_imx6dl # Colibri iMX6 Module
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b6fc2b375a61..e53abe1de259 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -446,6 +446,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-nitrogen6x.dtb \
imx6dl-phytec-mira-rdk-nand.dtb \
imx6dl-phytec-pbab01.dtb \
+ imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
imx6dl-riotboard.dtb \
imx6dl-sabreauto.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
new file mode 100644
index 000000000000..704410a84b0c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -0,0 +1,390 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Protonic VT7";
+ compatible = "prt,prtvt7", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ reg_12v_bl: regulator-bl-12v {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_12v_bl>;
+ compatible = "regulator-fixed";
+ regulator-name = "12v-bl";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ display: display {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ compatible = "fsl,imx-parallel-display";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ panel {
+ compatible = "innolux,g070y2t0ec";
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
+ hard_keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ esc {
+ label = "GPIO Key ESC";
+ linux,code = <KEY_ESC>;
+ gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
+ };
+
+ up {
+ label = "GPIO Key UP";
+ linux,code = <KEY_UP>;
+ gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
+ };
+
+ down {
+ label = "GPIO Key DOWN";
+ linux,code = <KEY_DOWN>;
+ gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
+ };
+
+ enter {
+ label = "GPIO Key Enter";
+ linux,code = <KEY_ENTER>;
+ gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
+ };
+
+ cycle {
+ label = "GPIO Key CYCLE";
+ linux,code = <KEY_CYCLEWINDOWS>;
+ gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
+ };
+
+ f1 {
+ label = "GPIO Key F1";
+ linux,code = <KEY_F1>;
+ gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
+ };
+
+ f2 {
+ label = "GPIO Key F2";
+ linux,code = <KEY_F2>;
+ gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
+ };
+
+ f3 {
+ label = "GPIO Key F3";
+ linux,code = <KEY_F3>;
+ gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
+ };
+
+ f4 {
+ label = "GPIO Key F4";
+ linux,code = <KEY_F4>;
+ gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
+ };
+
+ f5 {
+ label = "GPIO Key F5";
+ linux,code = <KEY_F5>;
+ gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
+ };
+
+ f6 {
+ label = "GPIO Key F6";
+ linux,code = <KEY_F6>;
+ gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
+ };
+
+ f7 {
+ label = "GPIO Key F7";
+ linux,code = <KEY_F7>;
+ gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
+ };
+
+ f8 {
+ label = "GPIO Key F8";
+ linux,code = <KEY_F8>;
+ gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
+ };
+
+ f9 {
+ label = "GPIO Key F9";
+ linux,code = <KEY_F9>;
+ gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
+ };
+
+ f10 {
+ label = "GPIO Key F10";
+ linux,code = <KEY_F10>;
+ gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&iomuxc {
+ prti6q {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ /* CAN1_SR output */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ /* ITU656_nRESET */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ /* ITU656_nPDN */
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
+ /* AUDIO_nRESET */
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
+
+ /* HW revision detect */
+ /* REV_ID0 */
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
+ /* REV_ID1 = PWM output LED_PWM (SION) */
+ /* defined in &pinctrl_pwm3 */
+ /* REV_ID2 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ /* REV_ID3 */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
+ /* REV_ID4 */
+ MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_tsc2046e: tsc2046egrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_12v_bl: 12blgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+ pinctrl_ipu1_disp: ipudisp1grp {
+ fsl,pins = <
+ /* DSE 0xb0 => 26 Ohm,
+ * 0xa0 => 37 Ohm,
+ * 0x90 => 78 Ohm
+ */
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0
+
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0
+
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0
+
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0
+ >;
+ };
+ };
+};
+
+&pcie {
+ status = "disabled";
+};
+
+&uart2 {
+ status = "disabled";
+};
+
+&uart5 {
+ status = "disabled";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&can2 {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
+
+&backlight_lcd {
+ pinctrl-names = "default";
+ pinctrl-0 = <>;
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000>;
+ brightness-levels = <0 5 7 9 12 15 20 27 35 47 62 81 107 142 188 248
+ 328 433 573 757 1000>;
+ default-brightness-level = <20>;
+ power-supply = <®_12v_bl>;
+ status = "okay";
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+
+ tsc: tsc2046e@0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc2046e>;
+ compatible = "ti,tsc2046";
+ spi-max-frequency = <100000>;
+ reg = <0>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
+ pendown-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ vcc-supply = <®_3v3>;
+
+ ti,vref-delay-usecs = /bits/ 16 <100>;
+
+ ti,x-min = /bits/ 16 <0>;
+ ti,x-max = /bits/ 16 <8000>;
+ ti,y-min = /bits/ 16 <0>;
+ ti,y-max = /bits/ 16 <4800>;
+ ti,x-plate-ohms = /bits/ 16 <800>;
+ ti,y-plate-ohms = /bits/ 16 <300>;
+ ti,pressure-max = /bits/ 16 <4095>;
+
+ ti,skip-samples = <2>;
+ ti,sample-period-msecs = <10>;
+ ti,report-period-msecs = <30>;
+
+ ti,filter-tolerance = <80>;
+ ti,touch-resistance-threshold = <3500>;
+ };
+};
+
+&ipu1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+ status = "okay";
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&leds {
+ led-hb0 {
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&i2c3 {
+ rtc: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ gpio_pca: gpio@74 {
+ compatible = "nxp,pca9539";
+ reg = <0x74>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 5/5] ARM: dts: add Protonic RVT board
2020-03-19 5:56 [PATCH v2 0/5] mainline Protonic boards Oleksij Rempel
` (3 preceding siblings ...)
2020-03-19 5:56 ` [PATCH v2 4/5] ARM: dts: add Protonic VT7 board Oleksij Rempel
@ 2020-03-19 5:56 ` Oleksij Rempel
4 siblings, 0 replies; 8+ messages in thread
From: Oleksij Rempel @ 2020-03-19 5:56 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, David Jander, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team
Protonic RVT is an internal development platform for a wireless ISObus
Virtual Terminal based on COTS tablets, and the predecessor of the WD2
platform.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/arm/fsl.yaml | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-prtrvt.dts | 108 ++++++++++++++++++
3 files changed, 110 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 424be1edf005..2e8a03ef5c95 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -168,6 +168,7 @@ properties:
- emtrion,emcon-mx6-avari # emCON-MX6S or emCON-MX6DL SoM on Avari Base
- fsl,imx6dl-sabreauto # i.MX6 DualLite/Solo SABRE Automotive Board
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
+ - prt,prtrvt # Protonic RVT board
- prt,prtvt7 # Protonic VT7 board
- technologic,imx6dl-ts4900
- technologic,imx6dl-ts7970
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e53abe1de259..afaccc9bc645 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -446,6 +446,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-nitrogen6x.dtb \
imx6dl-phytec-mira-rdk-nand.dtb \
imx6dl-phytec-pbab01.dtb \
+ imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
imx6dl-riotboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-prtrvt.dts b/arch/arm/boot/dts/imx6dl-prtrvt.dts
new file mode 100644
index 000000000000..fddc91b5a113
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-prtrvt.dts
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+
+/ {
+ model = "Protonic RVT board";
+ compatible = "prt,prtrvt", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x10000000>;
+ };
+};
+
+&iomuxc {
+ prti6q {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ /* CAN1_SR + CAN2_SR GPIO outputs */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
+
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ /* ITU656_nRESET */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+
+ /* HW revision detect */
+ /* REV_ID0 */
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
+ /* REV_ID1 */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ /* REV_ID2 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ /* REV_ID3 */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
+ /* REV_ID4 */
+ MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ /* DEBUG0 */
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ /* Not connected */
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+ };
+};
+
+&i2c3 {
+ rtc: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&pwm1 {
+ status = "disabled";
+};
+
+&ssi1 {
+ status = "disabled";
+};
+
+&uart2 {
+ status = "disabled";
+};
+
+&uart5 {
+ status = "disabled";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&can2 {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
+
+&audmux {
+ status = "disabled";
+};
+
+&ipu1 {
+ status = "disabled";
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v2 2/5] ARM: dts: add Protonic PRTI6Q board
2020-03-19 5:56 ` [PATCH v2 2/5] ARM: dts: add Protonic PRTI6Q board Oleksij Rempel
@ 2020-03-19 10:21 ` Marco Felsch
2020-03-24 10:51 ` Oleksij Rempel
0 siblings, 1 reply; 8+ messages in thread
From: Marco Felsch @ 2020-03-19 10:21 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo, devicetree,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Fabio Estevam, linux-arm-kernel
Hi Oleksij,
thanks for your patche. In general you should use generic node names,
sort the properties, nodes, phandles correctly except the iomux node.
Finally, pls don't mix dts and dtsi files. If the dts needs the iomux
than pls mux it within the dts file :) Pls see my comments below.
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright (c) 2014 Protonic Holland
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include "imx6qdl-prti6q.dtsi"
> +
> +/ {
> + model = "Protonic PRTI6Q board";
> + compatible = "prt,prti6q", "fsl,imx6q";
> +
> + memory@10000000 {
> + device_type = "memory";
> + reg = <0x10000000 0xf0000000>;
> + };
> +
> + sound-spdif {
> + compatible = "fsl,imx-audio-spdif";
> + model = "imx-spdif";
> + spdif-controller = <&spdif>;
> + spdif-in;
> + spdif-out;
> + };
> +
> + clocks {
Is this container necessary?
> + spi3_crystal: spi3clk {
Should we name the clock extcanclk?
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <25000000>;
> + };
> + };
> +
> + panel {
> + compatible = "kyo,tcg121xglp";
> + backlight = <&backlight_lcd>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +
> + reg_wl12xx: regulator-wl12xx {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wl1271_npd>;
Does npd mean no-power-down?
> + compatible = "regulator-fixed";
The "compatible" property should be the 1st property.
> + regulator-name = "regulator-WL12xx";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + gpio = <&gpio1 26 0>;
> + startup-delay-us = <70000>;
> + enable-active-high;
> + };
Please sort all nodes and phandles alphabetical, this applies to all
your .dts(i) files except the iomux node. I saw some dt files moving
that node to the end. @Shawn is this a unwritten rule?
> +};
> +
> +&ecspi2 {
> + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + status = "okay";
> +
> + can3: mcp2515@0 {
Where is this phandle used? Please name the node more generic e.g. like
the phandle and drop the phandle if not used.
> + compatible = "microchip,mcp2515";
> + spi-max-frequency = <5000000>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
> + reg = <0>;
The "reg" property should be listed after the "compatible" property.
> + clocks = <&spi3_crystal>;
> + };
> +
> + adc128: adc128@1 {
> + compatible = "ti,adc128s052";
> + reg = <1>;
> + vref-supply = <®_3v3>;
> + spi-max-frequency = <2000000>;
> + };
> +};
> +
> +&iomuxc {
> + prti6q {
Is this container necessary?
> + pinctrl_nand: nandgrp {
Where is this node used?
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
> + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
> + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
> + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
> + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
> + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
> + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
> + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
> + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
> + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
> + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
> + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
> + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
> + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
> + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
> + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
> + >;
> + };
> +
> + pinctrl_usbotg: usbotggrp {
Here we are mixing dtsi and dts files and the dtsi is not self-contained
anymore. This isn't a good idea.
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
> + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
> + /* power enable, high active */
> + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0
> + >;
> + };
> +
> + pinctrl_hdmi: hdmigrp {
> + fsl,pins = <
> + /* NOTE: DDC is done via I2C2, so DON'T
> + * configure DDC pins for HDMI!
> + */
> + MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
> + >;
> + };
> +
> + pinctrl_spdif: spdifgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
> + MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
> + >;
> + };
> +
> + pinctrl_leds: ledsgrp {
Here we are mixing it too.
> + fsl,pins = <
> + MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
> + MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
> + >;
> + };
> +
> + /* DDC */
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
Most of the node is already defined in your dtsi file and again
mixing dtsi and dts file. Pls check that for all your files. I
would mux the common things like miso,mosi,clk within the dtsi and the
cs signals here. Also we can use the phandle to extend the node.
> + fsl,pins = <
> + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> + /* CAN3 CS */
> + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> + /* ADC128S022 CS */
> + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
> + /* CAN3_nINT */
> + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
> + >;
> + };
> +
> + pinctrl_enet: enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
> +
> + /* Phy reset */
> + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
> + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
Why is this node needed? We only add the IRQ line. You only need to use
the phandle to extend the node or add a new wl1271grp. I would prefer
the 2nd.
> + fsl,pins = <
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> + /* WL12xx IRQ */
> + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
> + >;
> + };
> +
> + pinctrl_wl1271_npd: wl1271_npd {
Pls don't use '_' within node names.
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
> + >;
> + };
> + };
> +};
> +
> +&hdmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hdmi>;
> + ddc-i2c-bus = <&i2c2>;
> + status = "okay";
> +};
> +
> +&spdif {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spdif>;
> + status = "okay";
> +};
> +
> +/* DDC */
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +};
> +
> +&sata {
> + status = "okay";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet>;
> + phy-mode = "rgmii-id";
> + phy-handle = <&rgmii_phy>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microchip KSZ9031RNX PHY */
> + rgmii_phy: ethernet-phy@0 {
> + reg = <0>;
> + interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
> + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <10000>;
> + reset-deassert-us = <300>;
> + };
> + };
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds-channel@0 {
> + status = "okay";
> +
> + port@4 {
> + reg = <4>;
> +
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + vmmc-supply = <®_wl12xx>;
> + non-removable;
> + cap-power-off-card;
> + keep-power-in-suspend;
> + status = "okay";
> +
> + wl1271 {
> + compatible = "ti,wl1271";
> + irq-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> + ref-clock-frequency = "38400000";
> + tcxo-clock-frequency = "19200000";
> + };
> +};
> +
> +&snvs_poweroff {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
> new file mode 100644
> index 000000000000..6515b96fa0a5
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
Should we add the .dtsi file seperate?
> @@ -0,0 +1,489 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright (c) 2014 Protonic Holland
> + */
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/sound/fsl-imx-audmux.h>
> +
> +/ {
> + chosen {
> + stdout-path = &uart4;
> + };
> +
> + reg_3v3: regulator-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_1v8: regulator-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + reg_1v2: regulator-1v2 {
> + compatible = "regulator-fixed";
> + regulator-name = "1v2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + };
> +
> + reg_usb_otg_vbus: regulator-otg-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "otg-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio3 22 0>;
> + enable-active-high;
> + };
> +
> + reg_usb_h1_vbus: regulator-h1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "h1-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "prti6q-sgtl5000";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Line", "Line In Jack",
> + "Headphone", "Headphone Jack",
> + "Speaker", "External Speaker";
> + simple-audio-card,routing =
> + "MIC_IN", "Microphone Jack",
> + "LINE_IN", "Line In Jack",
> + "Headphone Jack", "HP_OUT",
> + "External Speaker", "LINE_OUT";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&ssi1>;
> + system-clock-frequency = <0>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&codec>;
> + bitclock-master;
> + frame-master;
> + };
> + };
> +
> + backlight_lcd: backlight-lcd {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_backlight>;
> + compatible = "pwm-backlight";
Should be the first property.
> + pwms = <&pwm1 0 5000000>;
> + brightness-levels = <0 1 2 4 6 8 12 16 24 32 48 64 96 128 192
> + 255>;
> + default-brightness-level = <15>;
Can you check the num-interpolated-steps property?
> + power-supply = <®_3v3>;
> + status = "okay";
Should be the last property.
> + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> + };
> +
> + leds: led-controller {
led-controller?
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_leds>;
> +
> + led-hb0 {
Do we need the led- prefix here?
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + led-mmc0 {
> + function = LED_FUNCTION_SD;
> + gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "disk-activity";
> + };
> + };
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +
> + mux_ssi1 {
> + fsl,audmux-port = <0>;
> + fsl,port-config = <
> + IMX_AUDMUX_V2_PTCR_SYN 0
> + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
> + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
> + IMX_AUDMUX_V2_PTCR_TFSDIR 0
> + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
> + >;
> + };
> +
> + mux_pins3 {
> + fsl,audmux-port = <2>;
> + fsl,port-config = <
> + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
> + 0 IMX_AUDMUX_V2_PDCR_TXRXEN
> + >;
> + };
> +};
> +
> +&ecspi1 {
> + cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
Nitpick, it is uncommon to list cs-gpios first.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1>;
> + status = "okay";
> +
> + flash: s25sl032p@0 {
Please use a generic name like spi-flash or flash.
> + compatible = "spansion,m25p80";
> + spi-max-frequency = <20000000>;
> + reg = <0>;
After the compatible string.
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "boot";
> + reg = <0x0 0x80000>;
> + };
> +
> + partition@80000 {
> + label = "env";
> + reg = <0x80000 0x10000>;
> + };
> +
> + partition@90000 {
> + label = "spare";
> + reg = <0x90000 0x370000>;
> + };
The partitions should be listed under the partitions node.
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + codec: sgtl5000@a {
Pls use generic names for all nodes, pls check that for all your dts(i)
files.
> + #sound-dai-cells = <0>;
> + compatible = "fsl,sgtl5000";
> + reg = <0xa>;
Compatible and reg should be moved to the begin.
> + clocks = <&clks 201>;
> + VDDA-supply = <®_3v3>;
> + VDDIO-supply = <®_3v3>;
> + VDDD-supply = <®_1v8>;
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +
> + can_adc: ads1015@49 {
Do we need the phandle here? Also node name is not generic and the
phandle is a bit odd can_adc listed under an i2c-node?
> + compatible = "ti,ads1015";
> + reg = <0x49>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + channel@4 {
> + reg = <4>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> +
> + channel@5 {
> + reg = <5>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> +
> + channel@6 {
> + reg = <6>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> +
> + channel@7 {
> + reg = <7>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> + };
> +
> + tmp103: tmp103@70 {
> + compatible = "ti,tmp103";
> + reg = <0x70>;
> + };
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + prti6q {
Is this container needed.
> + pinctrl_hog: hoggrp {
Pls, don't use hoggrps..
> + fsl,pins = <
> + /* SGTL5000 sys_mclk */
> + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
> + MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x100b0
> + MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x100b0
> + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b0
> + MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1b0b0
> + MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1b0b0
> + >;
> + };
> +
> + pinctrl_audmux: audmuxgrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
> + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
> + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
> + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
> + >;
> + };
> +
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> + /* CS */
> + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> + /* CS */
> + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> + /* CAN3_nINT */
> + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
> + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
> + MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart5: uart5grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
> + MX6QDL_PAD_GPIO_1__SD1_CD_B 0x1b0b0
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
> + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
> + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
> + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
> + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
> + >;
> + };
> +
> + pinctrl_can1: can1grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
> + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
> + >;
> + };
> +
> + pinctrl_can2: can2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
> + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
> + >;
> + };
> +
> + pinctrl_pwm1: pwm1grp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
> + >;
> + };
> +
> + pinctrl_backlight: backlightgrp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
> + >;
> + };
> +
> + pinctrl_ipu1_csi0: ipu1csi0grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
> + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
> + >;
> + };
> + };
> +};
> +
> +&pcie {
> + status = "okay";
> +};
> +
> +&pwm1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm1>;
> + status = "okay";
> +};
> +
> +&ssi1 {
> + #sound-dai-cells = <0>;
> + fsl,mode = "i2s-slave";
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + status = "okay";
> +};
> +
> +&uart5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart5>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usb_h1_vbus>;
> + phy_type = "utmi";
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <®_usb_otg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + phy_type = "utmi";
> + dr_mode = "host";
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #size-cells = <1>;
> + #address-cells = <1>;
> +
> + bootstate_backend: bootstate_backend@f0000 {
> + reg = <0xf0000 0x10000>;
> + label = "bootstate";
> + };
> + };
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can1>;
> + status = "okay";
> +};
> +
> +&can2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can2>;
> + status = "okay";
> +};
Regards,
Marco
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 2/5] ARM: dts: add Protonic PRTI6Q board
2020-03-19 10:21 ` Marco Felsch
@ 2020-03-24 10:51 ` Oleksij Rempel
0 siblings, 0 replies; 8+ messages in thread
From: Oleksij Rempel @ 2020-03-24 10:51 UTC (permalink / raw)
To: Marco Felsch
Cc: Mark Rutland, devicetree, Fabio Estevam, Sascha Hauer,
linux-kernel, Rob Herring, NXP Linux Team,
Pengutronix Kernel Team, David Jander, Shawn Guo,
linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 25079 bytes --]
On Thu, Mar 19, 2020 at 11:21:09AM +0100, Marco Felsch wrote:
> Hi Oleksij,
>
> thanks for your patche. In general you should use generic node names,
> sort the properties, nodes, phandles correctly except the iomux node.
> Finally, pls don't mix dts and dtsi files. If the dts needs the iomux
> than pls mux it within the dts file :) Pls see my comments below.
>
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright (c) 2014 Protonic Holland
> > + */
> > +
> > +/dts-v1/;
> > +#include "imx6q.dtsi"
> > +#include "imx6qdl-prti6q.dtsi"
> > +
> > +/ {
> > + model = "Protonic PRTI6Q board";
> > + compatible = "prt,prti6q", "fsl,imx6q";
> > +
> > + memory@10000000 {
> > + device_type = "memory";
> > + reg = <0x10000000 0xf0000000>;
> > + };
> > +
> > + sound-spdif {
> > + compatible = "fsl,imx-audio-spdif";
> > + model = "imx-spdif";
> > + spdif-controller = <&spdif>;
> > + spdif-in;
> > + spdif-out;
> > + };
> > +
> > + clocks {
>
> Is this container necessary?
removed.
> > + spi3_crystal: spi3clk {
>
> Should we name the clock extcanclk?
i synced it with schematics name
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <25000000>;
> > + };
> > + };
> > +
> > + panel {
> > + compatible = "kyo,tcg121xglp";
> > + backlight = <&backlight_lcd>;
> > +
> > + port {
> > + panel_in: endpoint {
> > + remote-endpoint = <&lvds0_out>;
> > + };
> > + };
> > + };
> > +
> > + reg_wl12xx: regulator-wl12xx {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_wl1271_npd>;
>
> Does npd mean no-power-down?
ACK
>
> > + compatible = "regulator-fixed";
>
> The "compatible" property should be the 1st property.
done
> > + regulator-name = "regulator-WL12xx";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + gpio = <&gpio1 26 0>;
> > + startup-delay-us = <70000>;
> > + enable-active-high;
> > + };
>
> Please sort all nodes and phandles alphabetical, this applies to all
> your .dts(i) files except the iomux node. I saw some dt files moving
> that node to the end. @Shawn is this a unwritten rule?
done
>
> > +};
> > +
> > +&ecspi2 {
> > + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi2>;
> > + status = "okay";
> > +
> > + can3: mcp2515@0 {
>
> Where is this phandle used? Please name the node more generic e.g. like
> the phandle and drop the phandle if not used.
done
> > + compatible = "microchip,mcp2515";
> > + spi-max-frequency = <5000000>;
> > + interrupt-parent = <&gpio3>;
> > + interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
> > + reg = <0>;
>
> The "reg" property should be listed after the "compatible" property.
done
> > + clocks = <&spi3_crystal>;
> > + };
> > +
> > + adc128: adc128@1 {
> > + compatible = "ti,adc128s052";
> > + reg = <1>;
> > + vref-supply = <®_3v3>;
> > + spi-max-frequency = <2000000>;
> > + };
> > +};
> > +
> > +&iomuxc {
> > + prti6q {
>
> Is this container necessary?
removed
> > + pinctrl_nand: nandgrp {
>
> Where is this node used?
removed and other nodes are reworked as well
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
> > + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
> > + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
> > + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
> > + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
> > + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
> > + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
> > + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
> > + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
> > + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
> > + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
> > + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
> > + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
> > + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
> > + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
> > + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
> > + >;
> > + };
> > +
> > + pinctrl_usbotg: usbotggrp {
>
> Here we are mixing dtsi and dts files and the dtsi is not self-contained
> anymore. This isn't a good idea.
done
>
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
> > + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
> > + /* power enable, high active */
> > + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0
> > + >;
> > + };
> > +
> > + pinctrl_hdmi: hdmigrp {
> > + fsl,pins = <
> > + /* NOTE: DDC is done via I2C2, so DON'T
> > + * configure DDC pins for HDMI!
> > + */
> > + MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
> > + >;
> > + };
> > +
> > + pinctrl_spdif: spdifgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
> > + MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_leds: ledsgrp {
>
> Here we are mixing it too.
done
> > + fsl,pins = <
> > + MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
> > + MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
> > + >;
> > + };
> > +
> > + /* DDC */
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_ecspi2: ecspi2grp {
>
> Most of the node is already defined in your dtsi file and again
> mixing dtsi and dts file. Pls check that for all your files. I
> would mux the common things like miso,mosi,clk within the dtsi and the
> cs signals here. Also we can use the phandle to extend the node.
done
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> > + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> > + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> > + /* CAN3 CS */
> > + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> > + /* ADC128S022 CS */
> > + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
> > + /* CAN3_nINT */
> > + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_enet: enetgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> > + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
> > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
> > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
> > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
> > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
> > + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
> > + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
> > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
> > + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
> > +
> > + /* Phy reset */
> > + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
> > + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
>
> Why is this node needed? We only add the IRQ line. You only need to use
> the phandle to extend the node or add a new wl1271grp. I would prefer
> the 2nd.
done
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> > + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> > + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> > + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> > + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> > + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> > + /* WL12xx IRQ */
> > + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
> > + >;
> > + };
> > +
> > + pinctrl_wl1271_npd: wl1271_npd {
>
> Pls don't use '_' within node names.
done
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
> > + >;
> > + };
> > + };
> > +};
> > +
> > +&hdmi {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hdmi>;
> > + ddc-i2c-bus = <&i2c2>;
> > + status = "okay";
> > +};
> > +
> > +&spdif {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_spdif>;
> > + status = "okay";
> > +};
> > +
> > +/* DDC */
> > +&i2c2 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +};
> > +
> > +&sata {
> > + status = "okay";
> > +};
> > +
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet>;
> > + phy-mode = "rgmii-id";
> > + phy-handle = <&rgmii_phy>;
> > + status = "okay";
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + /* Microchip KSZ9031RNX PHY */
> > + rgmii_phy: ethernet-phy@0 {
> > + reg = <0>;
> > + interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
> > + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> > + reset-assert-us = <10000>;
> > + reset-deassert-us = <300>;
> > + };
> > + };
> > +};
> > +
> > +&ldb {
> > + status = "okay";
> > +
> > + lvds-channel@0 {
> > + status = "okay";
> > +
> > + port@4 {
> > + reg = <4>;
> > +
> > + lvds0_out: endpoint {
> > + remote-endpoint = <&panel_in>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&usdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc2>;
> > + vmmc-supply = <®_wl12xx>;
> > + non-removable;
> > + cap-power-off-card;
> > + keep-power-in-suspend;
> > + status = "okay";
> > +
> > + wl1271 {
> > + compatible = "ti,wl1271";
> > + irq-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> > + ref-clock-frequency = "38400000";
> > + tcxo-clock-frequency = "19200000";
> > + };
> > +};
> > +
> > +&snvs_poweroff {
> > + status = "okay";
> > +};
> > diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
> > new file mode 100644
> > index 000000000000..6515b96fa0a5
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
>
> Should we add the .dtsi file seperate?
better no. it is useless as standalone file any way.
> > @@ -0,0 +1,489 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright (c) 2014 Protonic Holland
> > + */
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/leds/common.h>
> > +#include <dt-bindings/sound/fsl-imx-audmux.h>
> > +
> > +/ {
> > + chosen {
> > + stdout-path = &uart4;
> > + };
> > +
> > + reg_3v3: regulator-3v3 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_1v8: regulator-1v8 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "1v8";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_1v2: regulator-1v2 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "1v2";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_usb_otg_vbus: regulator-otg-vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "otg-vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + gpio = <&gpio3 22 0>;
> > + enable-active-high;
> > + };
> > +
> > + reg_usb_h1_vbus: regulator-h1-vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "h1-vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
> > + };
> > +
> > + sound {
> > + compatible = "simple-audio-card";
> > + simple-audio-card,name = "prti6q-sgtl5000";
> > + simple-audio-card,format = "i2s";
> > + simple-audio-card,widgets =
> > + "Microphone", "Microphone Jack",
> > + "Line", "Line In Jack",
> > + "Headphone", "Headphone Jack",
> > + "Speaker", "External Speaker";
> > + simple-audio-card,routing =
> > + "MIC_IN", "Microphone Jack",
> > + "LINE_IN", "Line In Jack",
> > + "Headphone Jack", "HP_OUT",
> > + "External Speaker", "LINE_OUT";
> > +
> > + simple-audio-card,cpu {
> > + sound-dai = <&ssi1>;
> > + system-clock-frequency = <0>;
> > + };
> > +
> > + simple-audio-card,codec {
> > + sound-dai = <&codec>;
> > + bitclock-master;
> > + frame-master;
> > + };
> > + };
> > +
> > + backlight_lcd: backlight-lcd {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_backlight>;
> > + compatible = "pwm-backlight";
>
> Should be the first property.
done
> > + pwms = <&pwm1 0 5000000>;
> > + brightness-levels = <0 1 2 4 6 8 12 16 24 32 48 64 96 128 192
> > + 255>;
> > + default-brightness-level = <15>;
>
> Can you check the num-interpolated-steps property?
done
> > + power-supply = <®_3v3>;
> > + status = "okay";
>
> Should be the last property.
done
> > + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + leds: led-controller {
>
> led-controller?
renamed to leds
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_leds>;
> > +
> > + led-hb0 {
>
> Do we need the led- prefix here?
if i interpret it properly, then yes:
Documentation/devicetree/bindings/leds/leds-gpio.yaml
> > + function = LED_FUNCTION_STATUS;
> > + gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "heartbeat";
> > + };
> > +
> > + led-mmc0 {
> > + function = LED_FUNCTION_SD;
> > + gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "disk-activity";
> > + };
> > + };
> > +};
> > +
> > +&audmux {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_audmux>;
> > + status = "okay";
> > +
> > + mux_ssi1 {
> > + fsl,audmux-port = <0>;
> > + fsl,port-config = <
> > + IMX_AUDMUX_V2_PTCR_SYN 0
> > + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
> > + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
> > + IMX_AUDMUX_V2_PTCR_TFSDIR 0
> > + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
> > + >;
> > + };
> > +
> > + mux_pins3 {
> > + fsl,audmux-port = <2>;
> > + fsl,port-config = <
> > + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
> > + 0 IMX_AUDMUX_V2_PDCR_TXRXEN
> > + >;
> > + };
> > +};
> > +
> > +&ecspi1 {
> > + cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
>
> Nitpick, it is uncommon to list cs-gpios first.
git grep -B1 "cs-gpios" arch/arm/boot/dts/
shows, it is common.
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi1>;
> > + status = "okay";
> > +
> > + flash: s25sl032p@0 {
>
> Please use a generic name like spi-flash or flash.
done
> > + compatible = "spansion,m25p80";
> > + spi-max-frequency = <20000000>;
> > + reg = <0>;
>
> After the compatible string.
done
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + partition@0 {
> > + label = "boot";
> > + reg = <0x0 0x80000>;
> > + };
> > +
> > + partition@80000 {
> > + label = "env";
> > + reg = <0x80000 0x10000>;
> > + };
> > +
> > + partition@90000 {
> > + label = "spare";
> > + reg = <0x90000 0x370000>;
> > + };
>
> The partitions should be listed under the partitions node.
done
> > + };
> > +};
> > +
> > +&i2c1 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + status = "okay";
> > +
> > + codec: sgtl5000@a {
>
> Pls use generic names for all nodes, pls check that for all your dts(i)
> files.
done
> > + #sound-dai-cells = <0>;
> > + compatible = "fsl,sgtl5000";
> > + reg = <0xa>;
>
> Compatible and reg should be moved to the begin.
done
> > + clocks = <&clks 201>;
> > + VDDA-supply = <®_3v3>;
> > + VDDIO-supply = <®_3v3>;
> > + VDDD-supply = <®_1v8>;
> > + };
> > +};
> > +
> > +&i2c3 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + status = "okay";
> > +
> > + can_adc: ads1015@49 {
>
> Do we need the phandle here? Also node name is not generic and the
> phandle is a bit odd can_adc listed under an i2c-node?
removed and renamed
> > + compatible = "ti,ads1015";
> > + reg = <0x49>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + channel@4 {
> > + reg = <4>;
> > + ti,gain = <3>;
> > + ti,datarate = <3>;
> > + };
> > +
> > + channel@5 {
> > + reg = <5>;
> > + ti,gain = <3>;
> > + ti,datarate = <3>;
> > + };
> > +
> > + channel@6 {
> > + reg = <6>;
> > + ti,gain = <3>;
> > + ti,datarate = <3>;
> > + };
> > +
> > + channel@7 {
> > + reg = <7>;
> > + ti,gain = <3>;
> > + ti,datarate = <3>;
> > + };
> > + };
> > +
> > + tmp103: tmp103@70 {
> > + compatible = "ti,tmp103";
> > + reg = <0x70>;
> > + };
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hog>;
> > +
> > + prti6q {
>
> Is this container needed.
removed
> > + pinctrl_hog: hoggrp {
>
> Pls, don't use hoggrps..
removed
> > + fsl,pins = <
> > + /* SGTL5000 sys_mclk */
> > + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
> > + MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x100b0
> > + MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x100b0
> > + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b0
> > + MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1b0b0
> > + MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_audmux: audmuxgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
> > + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
> > + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
> > + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
> > + >;
> > + };
> > +
> > + pinctrl_ecspi1: ecspi1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> > + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> > + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> > + /* CS */
> > + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
> > + >;
> > + };
> > +
> > + pinctrl_ecspi2: ecspi2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> > + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> > + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> > + /* CS */
> > + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> > + /* CAN3_nINT */
> > + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c1: i2c1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
> > + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c3: i2c3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> > + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_uart2: uart2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
> > + MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
> > + MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
> > + MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_uart4: uart4grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> > + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_uart5: uart5grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
> > + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1: usdhc1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
> > + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
> > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
> > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
> > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
> > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
> > + MX6QDL_PAD_GPIO_1__SD1_CD_B 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> > + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> > + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> > + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> > + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> > + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3: usdhc3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
> > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
> > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
> > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
> > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
> > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
> > + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
> > + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
> > + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
> > + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
> > + >;
> > + };
> > +
> > + pinctrl_can1: can1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
> > + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
> > + >;
> > + };
> > +
> > + pinctrl_can2: can2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
> > + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
> > + >;
> > + };
> > +
> > + pinctrl_pwm1: pwm1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_backlight: backlightgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_ipu1_csi0: ipu1csi0grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
> > + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
> > + >;
> > + };
> > + };
> > +};
> > +
> > +&pcie {
> > + status = "okay";
> > +};
> > +
> > +&pwm1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pwm1>;
> > + status = "okay";
> > +};
> > +
> > +&ssi1 {
> > + #sound-dai-cells = <0>;
> > + fsl,mode = "i2s-slave";
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart2>;
> > + status = "okay";
> > +};
> > +
> > +&uart4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart4>;
> > + status = "okay";
> > +};
> > +
> > +&uart5 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart5>;
> > + status = "okay";
> > +};
> > +
> > +&usbh1 {
> > + vbus-supply = <®_usb_h1_vbus>;
> > + phy_type = "utmi";
> > + dr_mode = "host";
> > + status = "okay";
> > +};
> > +
> > +&usbotg {
> > + vbus-supply = <®_usb_otg_vbus>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbotg>;
> > + phy_type = "utmi";
> > + dr_mode = "host";
> > + disable-over-current;
> > + status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +};
> > +
> > +&usdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc2>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&usdhc3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc3>;
> > + bus-width = <8>;
> > + non-removable;
> > + status = "okay";
> > +
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #size-cells = <1>;
> > + #address-cells = <1>;
> > +
> > + bootstate_backend: bootstate_backend@f0000 {
> > + reg = <0xf0000 0x10000>;
> > + label = "bootstate";
> > + };
> > + };
> > +};
> > +
> > +&can1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_can1>;
> > + status = "okay";
> > +};
> > +
> > +&can2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_can2>;
> > + status = "okay";
> > +};
>
> Regards,
> Marco
>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2020-03-24 10:51 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-19 5:56 [PATCH v2 0/5] mainline Protonic boards Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 1/5] dt-bindings: vendor-prefixes: Add an entry for Protonic Holland Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 2/5] ARM: dts: add Protonic PRTI6Q board Oleksij Rempel
2020-03-19 10:21 ` Marco Felsch
2020-03-24 10:51 ` Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 3/5] ARM: dts: add Protonic WD2 board Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 4/5] ARM: dts: add Protonic VT7 board Oleksij Rempel
2020-03-19 5:56 ` [PATCH v2 5/5] ARM: dts: add Protonic RVT board Oleksij Rempel
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).