From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
To: linux-clk@vger.kernel.org, sboyd@kernel.org
Cc: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Subject: [PATCH v1 1/6] clk: divider: Implement and wire up .determine_rate by default
Date: Sat, 3 Jul 2021 00:51:40 +0200 [thread overview]
Message-ID: <20210702225145.2643303-2-martin.blumenstingl@googlemail.com> (raw)
In-Reply-To: <20210702225145.2643303-1-martin.blumenstingl@googlemail.com>
.determine_rate is meant to replace .round_rate. The former comes with a
benefit which is especially relevant on 32-bit systems: since
.determine_rate uses an "unsigned long" (compared to a "signed long"
which is used by .round_rate) the maximum value on 32-bit systems
increases from 2^31 (or approx. 2.14GHz) to 2^32 (or approx. 4.29GHz).
Implement .determine_rate in addition to .round_rate so drivers that are
using clk_divider_{ro_,}ops can benefit from this by default. Keep the
.round_rate callback for now since some drivers rely on
clk_divider_ops.round_rate being implemented.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
drivers/clk/clk-divider.c | 23 +++++++++++++++++++++++
1 file changed, 23 insertions(+)
diff --git a/drivers/clk/clk-divider.c b/drivers/clk/clk-divider.c
index 87ba4966b0e8..f6b2bf558486 100644
--- a/drivers/clk/clk-divider.c
+++ b/drivers/clk/clk-divider.c
@@ -446,6 +446,27 @@ static long clk_divider_round_rate(struct clk_hw *hw, unsigned long rate,
divider->width, divider->flags);
}
+static int clk_divider_determine_rate(struct clk_hw *hw,
+ struct clk_rate_request *req)
+{
+ struct clk_divider *divider = to_clk_divider(hw);
+
+ /* if read only, just return current value */
+ if (divider->flags & CLK_DIVIDER_READ_ONLY) {
+ u32 val;
+
+ val = clk_div_readl(divider) >> divider->shift;
+ val &= clk_div_mask(divider->width);
+
+ return divider_ro_determine_rate(hw, req, divider->table,
+ divider->width,
+ divider->flags, val);
+ }
+
+ return divider_determine_rate(hw, req, divider->table, divider->width,
+ divider->flags);
+}
+
int divider_get_val(unsigned long rate, unsigned long parent_rate,
const struct clk_div_table *table, u8 width,
unsigned long flags)
@@ -501,6 +522,7 @@ static int clk_divider_set_rate(struct clk_hw *hw, unsigned long rate,
const struct clk_ops clk_divider_ops = {
.recalc_rate = clk_divider_recalc_rate,
.round_rate = clk_divider_round_rate,
+ .determine_rate = clk_divider_determine_rate,
.set_rate = clk_divider_set_rate,
};
EXPORT_SYMBOL_GPL(clk_divider_ops);
@@ -508,6 +530,7 @@ EXPORT_SYMBOL_GPL(clk_divider_ops);
const struct clk_ops clk_divider_ro_ops = {
.recalc_rate = clk_divider_recalc_rate,
.round_rate = clk_divider_round_rate,
+ .determine_rate = clk_divider_determine_rate,
};
EXPORT_SYMBOL_GPL(clk_divider_ro_ops);
--
2.32.0
next prev parent reply other threads:[~2021-07-02 22:52 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-07-02 22:51 [PATCH v1 0/6] clk: switch dividers to .determine_rate Martin Blumenstingl
2021-07-02 22:51 ` Martin Blumenstingl [this message]
2021-08-06 1:10 ` [PATCH v1 1/6] clk: divider: Implement and wire up .determine_rate by default Stephen Boyd
2021-10-14 9:55 ` Alex Bee
2021-10-14 12:11 ` Martin Blumenstingl
2021-10-14 21:34 ` Martin Blumenstingl
2021-10-14 22:52 ` Stephen Boyd
2021-10-15 12:05 ` [PATCH] clk: composite: Also consider .determine_rate for rate + mux composites Martin Blumenstingl
2021-10-15 21:27 ` Stephen Boyd
2021-11-01 20:19 ` Guillaume Tucker
2021-11-01 20:58 ` Martin Blumenstingl
2021-11-01 21:59 ` Robin Murphy
2021-11-01 22:11 ` Robin Murphy
2021-11-01 22:41 ` Alex Bee
2021-11-02 7:58 ` Guillaume Tucker
2021-11-02 21:40 ` LABBE Corentin
2021-10-15 19:14 ` [PATCH v1 1/6] clk: divider: Implement and wire up .determine_rate by default Alex Bee
2021-10-15 21:31 ` Stephen Boyd
2021-07-02 22:51 ` [PATCH v1 2/6] clk: imx: clk-divider-gate: Switch to clk_divider.determine_rate Martin Blumenstingl
2021-07-19 10:43 ` Abel Vesa
2021-07-29 11:30 ` Abel Vesa
2021-07-02 22:51 ` [PATCH v1 3/6] clk: bcm2835: " Martin Blumenstingl
2021-07-05 6:57 ` Marek Szyprowski
2021-08-06 1:10 ` Stephen Boyd
2021-07-02 22:51 ` [PATCH v1 4/6] clk: stm32f4: " Martin Blumenstingl
2021-08-06 1:10 ` Stephen Boyd
2021-07-02 22:51 ` [PATCH v1 5/6] clk: stm32h7: " Martin Blumenstingl
2021-08-06 1:10 ` Stephen Boyd
2021-07-02 22:51 ` [PATCH v1 6/6] clk: stm32mp1: " Martin Blumenstingl
2021-08-06 1:10 ` Stephen Boyd
2021-08-03 19:32 ` [PATCH v1 0/6] clk: switch dividers to .determine_rate Martin Blumenstingl
2021-08-03 20:16 ` Stephen Boyd
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210702225145.2643303-2-martin.blumenstingl@googlemail.com \
--to=martin.blumenstingl@googlemail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=sboyd@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).